Innosilicon t3 50 arrived.

[Hockeybum]

I just wanted to update that that Innosilicon did send my miners, they arrived today and I will be installing them next week.

[1715002453]

1715002453

[1715002453]

1715002453

[1715002453]

1715002453

[1715002453]

1715002453

[1715002453]

1715002453

[philipma1957]

I just wanted to update that that Innosilicon did send my miners, they arrived today and I will be installing them next week.

Good news so about a 25-30 day delay.

And you had to upgrade from 43th at 100 or 125 a miner ?

My single t3 50 does well on factory+ but it does suck a lot of power say 3350 watts.

Pretty annoyed with innosilicon myself and I know you are more annoyed.

So let’s tally

The bad:
Inno late for many
Pulls extra watts
Many had to pay for forced upgrades from 43th to 50th.

The good :

It can do 50.50 t at factory plus
So far It works

[Biffa]

I didn't take them up on the offer of an "upgrade" to T50, so I pulled out of my T43's and got a refund.

It did take 23 days for them to actually send the refund after I requested it, but it did come through.

[minefarmbuy]

Promotional pricing for T3 is live but looks like not the T2 yet.

https://twitter.com/Inno_Miner/status/1184408814386200576?s=201

[Biffa]

My hosting provide won't allow them in the datacenter anymore.

[minefarmbuy]

Probably because pdu change for c19/c20.

[Biffa]

No more because the PSU's die all the time and they consider them a fire risk

[philipma1957]

Yep cause the units need to be run at lower then preformance if you run them long term.

Mine runs at factory +  and I use a voltage regulator that keep power at 227-233 volts.

If you have 208 3 phase and run this psu a long time many  units struggle to do factory speed and will need to do balance +

many big hosts  are 208 3 phase  and can run around 205 volts  this psu will not keep up on preformance setting.

I found a decent 230 volt regulator  that  is rated for 20amps  So far it has been very good. I have four of them:

https://www.ebay.com/itm/New-SmartPower-Systems-Automatic-Voltage-Regulator-AVR20-230TBF-Plus/372797321665

I  got two at 200 and two at 150

I got one from the seller above. His works well.  as did the others for the other sellers.

My thoughts are this could be helpful if you are running

s17
t17

t3 50
t3 39

on 208 volt 3 phase circuits.  But I think no hoster will want to be bothered with them.

[Philopolymath]

My T3+ 57Th  have finally arrived and I have them fired up to test before they are off to the Host.
So far so good exactly at spec...57th on performance drawing 3300W Fans steady at 70% with chip temps hovering in low 70's.

So
High performance we have 57Th @ 3300W (Insane jet engine loud when warm)
Reduced settings
Factory setting puts out 50Th @ 2550W Ambient is 65F (Not for long) fans @50%..... chips temps high 60's
Balanced........not checked yet
Economy.....39Th @ 1800W !!!! And Not too loud at all...tolerable

These are early results after only a few hours on each.
Definitely will NOT be running them full tilt.
All this on stock firmware
These units are for sale in Ottawa but will soon be in Labrador at Cryptoboreas

[philipma1957]

Factory setting puts out 50Th @ 2550W Ambient is 65F (Not for long) fans @50%..... chips temps high 60's

This is good   it is better then the  bitmain t17e I got yesterday

It does 54th at 3356

your factory setting of 50th at 2550   is 800 watt savings at a loss of 4th
your high setting of 57th  at 3300     is 56 watts savings with 3 th extra

Right now innosilicon is blowing out  the t3+ 57th

https://www.innosilicon.com/html/t3+57t-miner/index.html

1666 plus shipping

all of bitmains gear is a bit slower or a month slower.  So at the moment  this is kind of competitive.

[minefarmbuy]

while the sale is happening and the bonus unit, philip as usual is correct.

[philipma1957]

while the sale is happening and the bonus unit, philip as usual is correct.

yep and I am still pissed off at them, but to be fair bitmain  has been crappy as of late.  So I have issues with them. Along with pangolinminer.