nicehash not working with T17 antminer

[adamjamal]

Hello,

I have a problem regarding nicehash after the last update the T17 won't work when i use nicehash pool the hashrate remains zero in the miner state , i tried to go back to my old firmware but i couldn't , any ideas for the cause of this problem and solutions , thanks in advance .

this one is working just fine with nicehash : Antminer-T17-user-OM-201912051119-sig_4803.tar
the problem is with this : Antminer-T17-user-OM-201912241613-sig_5047.tar

I also tried another pool and it was working fine the problem is with nicehash only !

kernel log when using nicehash

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203756K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25620K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12580K (cceb8000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 12/6, WL threshold: 4096, image sequence number: 72543235
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID D94047F6-1175-4366-977B-837CC879EE19, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 39/20, WL threshold: 4096, image sequence number: 3389548455
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 721E72E7-F382-4130-AD9F-6C10D9102537, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
2020-01-14 08:30:36 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2020-01-14 08:30:36 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2020-01-14 08:30:36 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2020-01-14 08:30:36 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-01-14 08:30:36 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2020-01-14 08:30:36 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2020-01-14 08:30:36 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2020-01-14 08:30:36 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2020-01-14 08:30:36 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-01-14 08:30:36 thread.c:789:create_read_nonce_reg_thread: create thread
2020-01-14 08:30:42 driver-btm-api.c:1067:init_miner_version: miner ID : 804824025c20885c
2020-01-14 08:30:42 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-01-14 08:30:43 eeprom.c:431:check_pattern_test_level: L1 board
2020-01-14 08:30:45 eeprom.c:431:check_pattern_test_level: L1 board
2020-01-14 08:30:47 eeprom.c:431:check_pattern_test_level: L1 board
2020-01-14 08:30:47 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-01-14 08:30:47 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-01-14 08:30:47 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-01-14 08:30:47 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-01-14 08:30:47 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-01-14 08:30:47 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-01-14 08:30:47 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-01-14 08:30:47 driver-btm-api.c:644:_set_project_type: project:2
2020-01-14 08:30:47 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-01-14 08:30:47 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-01-14 08:30:47 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-01-14 08:30:47 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-01-14 08:30:47 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-01-14 08:30:47 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-01-14 08:30:47 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-01-14 08:30:48 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-01-14 08:30:50 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-01-14 08:30:53 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-01-14 08:30:55 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-01-14 08:30:58 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-01-14 08:31:00 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-01-14 08:31:04 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-01-14 08:31:04 thread.c:784:create_pic_heart_beat_thread: create thread
2020-01-14 08:31:04 power_api.c:55:power_init: power init ... 
2020-01-14 08:31:04 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-01-14 08:31:36 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-01-14 08:31:41 power_api.c:124:check_voltage_multi: retry time: 0
2020-01-14 08:31:43 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.273115 
2020-01-14 08:31:45 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.346592 
2020-01-14 08:31:47 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.297607 
2020-01-14 08:31:47 power_api.c:97:get_average_voltage: aveage voltage is: 17.305771 
2020-01-14 08:31:47 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-01-14 08:31:47 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-01-14 08:31:47 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-01-14 08:31:47 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-01-14 08:31:47 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-01-14 08:31:58 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-01-14 08:32:08 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-01-14 08:32:18 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-01-14 08:32:22 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-01-14 08:32:22 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-01-14 08:32:22 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-01-14 08:32:22 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-01-14 08:32:22 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-01-14 08:32:22 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-01-14 08:32:22 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-01-14 08:32:22 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-01-14 08:32:22 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-01-14 08:32:23 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-01-14 08:32:23 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-01-14 08:32:23 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-01-14 08:32:23 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-01-14 08:32:23 voltage[0] = 1690
2020-01-14 08:32:23 voltage[1] = 1690
2020-01-14 08:32:23 voltage[2] = 1690
2020-01-14 08:32:23 power_api.c:140:set_working_voltage: working_voltage = 16.900000
2020-01-14 08:32:24 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-01-14 08:32:26 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-01-14 08:32:27 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-01-14 08:32:27 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-01-14 08:32:27 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-01-14 08:32:27 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-01-14 08:32:27 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-01-14 08:32:29 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 17
2020-01-14 08:32:29 thread.c:804:create_check_miner_status_thread: create thread
2020-01-14 08:32:29 thread.c:794:create_set_miner_status_thread: create thread
2020-01-14 08:32:29 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-01-14 08:32:29 thread.c:779:create_temperature_monitor_thread: create thread
2020-01-14 08:32:29 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2020-01-14 08:32:29 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.80 ...
2020-01-14 08:33:04 power_api.c:124:check_voltage_multi: retry time: 0
2020-01-14 08:33:06 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.050742 
2020-01-14 08:33:07 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.167080 
2020-01-14 08:33:09 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.093603 
2020-01-14 08:33:09 power_api.c:97:get_average_voltage: aveage voltage is: 18.103808 
2020-01-14 08:33:09 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-01-14 08:33:09 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-01-14 08:33:09 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-01-14 08:33:10 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-01-14 08:33:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-01-14 08:33:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-01-14 08:33:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-01-14 08:33:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-01-14 08:33:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-01-14 08:33:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-01-14 08:33:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-01-14 08:33:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-01-14 08:33:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-01-14 08:33:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-01-14 08:33:13 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-01-14 08:33:13 driver-btm-api.c:612:set_timeout: freq 720 final timeout=163
2020-01-14 08:33:13 power_api.c:146:set_higher_voltage: higher_voltage = 17.900000
2020-01-14 08:33:13 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 17.90 ...
2020-01-14 08:33:40 power_api.c:124:check_voltage_multi: retry time: 0
2020-01-14 08:33:43 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.209941 
2020-01-14 08:33:46 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.320156 
2020-01-14 08:33:49 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.234433 
2020-01-14 08:33:49 power_api.c:97:get_average_voltage: aveage voltage is: 18.254844 
2020-01-14 08:33:49 frequency.c:540:get_current_min_freq: current min freq 720
2020-01-14 08:33:49 driver-btm-api.c:1660:check_clock_counter: freq 720 clock_counter_limit 92
2020-01-14 08:33:51 thread.c:799:create_check_system_status_thread: create thread
2020-01-14 08:33:52 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2020-01-14 08:33:52 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2020-01-14 08:33:56 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-01-14 08:34:01 driver-btm-api.c:1293:dhash_chip_send_job: Version num 1
[/quote]

kernel log with another pool working 
[quote]

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203756K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25620K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12580K (cceb8000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 12/6, WL threshold: 4096, image sequence number: 72543235
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID D94047F6-1175-4366-977B-837CC879EE19, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 39/20, WL threshold: 4096, image sequence number: 3389548455
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 721E72E7-F382-4130-AD9F-6C10D9102537, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
2020-01-13 19:51:26 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2020-01-13 19:51:26 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2020-01-13 19:51:26 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2020-01-13 19:51:26 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-01-13 19:51:26 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2020-01-13 19:51:26 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2020-01-13 19:51:26 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2020-01-13 19:51:26 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2020-01-13 19:51:26 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-01-13 19:51:26 thread.c:789:create_read_nonce_reg_thread: create thread
2020-01-13 19:51:32 driver-btm-api.c:1067:init_miner_version: miner ID : 804824025c20885c
2020-01-13 19:51:32 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-01-13 19:51:34 eeprom.c:431:check_pattern_test_level: L1 board
2020-01-13 19:51:36 eeprom.c:431:check_pattern_test_level: L1 board
2020-01-13 19:51:37 eeprom.c:431:check_pattern_test_level: L1 board
2020-01-13 19:51:37 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-01-13 19:51:37 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-01-13 19:51:37 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-01-13 19:51:37 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-01-13 19:51:37 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-01-13 19:51:37 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-01-13 19:51:37 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-01-13 19:51:37 driver-btm-api.c:644:_set_project_type: project:2
2020-01-13 19:51:37 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-01-13 19:51:37 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-01-13 19:51:37 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-01-13 19:51:37 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-01-13 19:51:37 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-01-13 19:51:37 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-01-13 19:51:37 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-01-13 19:51:39 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-01-13 19:51:39 register.c:283:get_register: !!! reg crc error
2020-01-13 19:51:41 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-01-13 19:51:45 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-01-13 19:51:46 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-01-13 19:51:50 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-01-13 19:51:52 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-01-13 19:51:55 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-01-13 19:51:55 thread.c:784:create_pic_heart_beat_thread: create thread
2020-01-13 19:51:55 power_api.c:55:power_init: power init ... 
2020-01-13 19:51:55 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-01-13 19:52:27 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-01-13 19:52:33 power_api.c:124:check_voltage_multi: retry time: 0
2020-01-13 19:52:34 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.965019 
2020-01-13 19:52:36 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.475176 
2020-01-13 19:52:38 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.260869 
2020-01-13 19:52:38 power_api.c:97:get_average_voltage: aveage voltage is: 17.567021 
2020-01-13 19:52:38 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-01-13 19:52:38 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-01-13 19:52:38 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-01-13 19:52:38 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-01-13 19:52:38 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-01-13 19:52:50 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-01-13 19:52:59 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-01-13 19:53:10 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-01-13 19:53:13 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-01-13 19:53:13 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-01-13 19:53:14 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-01-13 19:53:14 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-01-13 19:53:14 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-01-13 19:53:14 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-01-13 19:53:14 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-01-13 19:53:14 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-01-13 19:53:14 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-01-13 19:53:14 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-01-13 19:53:14 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-01-13 19:53:14 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-01-13 19:53:14 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-01-13 19:53:14 voltage[0] = 1690
2020-01-13 19:53:14 voltage[1] = 1690
2020-01-13 19:53:14 voltage[2] = 1690
2020-01-13 19:53:14 power_api.c:140:set_working_voltage: working_voltage = 16.900000
2020-01-13 19:53:16 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-01-13 19:53:17 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-01-13 19:53:19 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-01-13 19:53:19 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-01-13 19:53:19 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-01-13 19:53:19 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-01-13 19:53:19 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-01-13 19:53:20 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 17
2020-01-13 19:53:20 thread.c:804:create_check_miner_status_thread: create thread
2020-01-13 19:53:20 thread.c:794:create_set_miner_status_thread: create thread
2020-01-13 19:53:20 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-01-13 19:53:20 thread.c:779:create_temperature_monitor_thread: create thread
2020-01-13 19:53:20 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2020-01-13 19:53:20 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.80 ...
2020-01-13 19:53:55 power_api.c:124:check_voltage_multi: retry time: 0
2020-01-13 19:53:57 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.081357 
2020-01-13 19:53:59 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.167080 
2020-01-13 19:54:01 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.093603 
2020-01-13 19:54:01 power_api.c:97:get_average_voltage: aveage voltage is: 18.114013 
2020-01-13 19:54:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-01-13 19:54:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-01-13 19:54:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-01-13 19:54:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-01-13 19:54:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-01-13 19:54:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-01-13 19:54:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-01-13 19:54:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-01-13 19:54:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-01-13 19:54:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-01-13 19:54:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-01-13 19:54:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-01-13 19:54:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-01-13 19:54:03 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-01-13 19:54:03 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-01-13 19:54:03 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-01-13 19:54:03 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-01-13 19:54:03 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-01-13 19:54:03 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-01-13 19:54:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-01-13 19:54:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-01-13 19:54:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-01-13 19:54:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-01-13 19:54:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-01-13 19:54:04 driver-btm-api.c:612:set_timeout: freq 720 final timeout=163
2020-01-13 19:54:04 power_api.c:146:set_higher_voltage: higher_voltage = 17.900000
2020-01-13 19:54:04 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 17.90 ...
2020-01-13 19:54:31 power_api.c:124:check_voltage_multi: retry time: 0
2020-01-13 19:54:34 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.240556 
2020-01-13 19:54:37 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.326279 
2020-01-13 19:54:41 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.246679 
2020-01-13 19:54:41 power_api.c:97:get_average_voltage: aveage voltage is: 18.271172 
2020-01-13 19:54:41 frequency.c:540:get_current_min_freq: current min freq 720
2020-01-13 19:54:41 driver-btm-api.c:1660:check_clock_counter: freq 720 clock_counter_limit 92
2020-01-13 19:54:43 thread.c:799:create_check_system_status_thread: create thread
2020-01-13 19:54:43 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2020-01-13 19:54:43 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2020-01-13 19:54:48 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-01-13 19:55:02 driver-btm-api.c:1293:dhash_chip_send_job: Version num 1
2020-01-13 19:55:12 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
2020-01-13 19:55:16 thread.c:382:check_working_voltage: current PCB min temperature is 41
2020-01-13 19:55:16 thread.c:383:check_working_voltage: current voltage is 17.90V, recovery to 16.90V
2020-01-13 19:55:16 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 16.90 ...
2020-01-13 19:55:48 power_api.c:124:check_voltage_multi: retry time: 0
2020-01-13 19:55:50 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.187392 
2020-01-13 19:55:52 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.285361 
2020-01-13 19:55:55 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.248623 
2020-01-13 19:55:55 power_api.c:97:get_average_voltage: aveage voltage is: 17.240459 
2020-01-13 20:00:54 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 18101
2020-01-13 20:00:54 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 17812
2020-01-13 20:00:54 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 18076
2020-01-13 20:25:55 thread.c:204:calc_hashrate_avg: avg rate is 43449.37 in 30 mins
2020-01-13 20:25:55 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-13 20:55:56 thread.c:204:calc_hashrate_avg: avg rate is 43336.34 in 30 mins
2020-01-13 20:55:56 temperature.c:450:temp_statistics_show:   pcb temp 41~54  chip temp 66~80
2020-01-13 21:25:58 thread.c:204:calc_hashrate_avg: avg rate is 43503.58 in 30 mins
2020-01-13 21:25:58 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-13 21:55:59 thread.c:204:calc_hashrate_avg: avg rate is 43653.85 in 30 mins
2020-01-13 21:55:59 temperature.c:450:temp_statistics_show:   pcb temp 41~55  chip temp 66~80
2020-01-13 22:26:00 thread.c:204:calc_hashrate_avg: avg rate is 43404.55 in 30 mins
2020-01-13 22:26:00 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-13 22:56:01 thread.c:204:calc_hashrate_avg: avg rate is 43437.54 in 30 mins
2020-01-13 22:56:01 temperature.c:450:temp_statistics_show:   pcb temp 41~54  chip temp 66~80
2020-01-13 23:26:03 thread.c:204:calc_hashrate_avg: avg rate is 43445.93 in 30 mins
2020-01-13 23:26:03 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 65~80
2020-01-13 23:56:04 thread.c:204:calc_hashrate_avg: avg rate is 43184.22 in 30 mins
2020-01-13 23:56:04 temperature.c:450:temp_statistics_show:   pcb temp 41~54  chip temp 66~80
2020-01-14 00:26:05 thread.c:204:calc_hashrate_avg: avg rate is 43414.31 in 30 mins
2020-01-14 00:26:05 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-14 00:56:07 thread.c:204:calc_hashrate_avg: avg rate is 43207.67 in 30 mins
2020-01-14 00:56:07 temperature.c:450:temp_statistics_show:   pcb temp 41~55  chip temp 66~80
2020-01-14 01:26:08 thread.c:204:calc_hashrate_avg: avg rate is 43043.22 in 30 mins
2020-01-14 01:26:08 temperature.c:450:temp_statistics_show:   pcb temp 41~55  chip temp 67~80
2020-01-14 01:56:09 thread.c:204:calc_hashrate_avg: avg rate is 43511.56 in 30 mins
2020-01-14 01:56:09 temperature.c:450:temp_statistics_show:   pcb temp 40~55  chip temp 66~80
2020-01-14 02:26:11 thread.c:204:calc_hashrate_avg: avg rate is 43656.22 in 30 mins
2020-01-14 02:26:11 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-14 02:56:12 thread.c:204:calc_hashrate_avg: avg rate is 43388.33 in 30 mins
2020-01-14 02:56:12 temperature.c:450:temp_statistics_show:   pcb temp 40~55  chip temp 66~81
2020-01-14 03:26:13 thread.c:204:calc_hashrate_avg: avg rate is 43617.73 in 30 mins
2020-01-14 03:26:13 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-14 03:56:14 thread.c:204:calc_hashrate_avg: avg rate is 43377.63 in 30 mins
2020-01-14 03:56:14 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 65~80
2020-01-14 04:26:16 thread.c:204:calc_hashrate_avg: avg rate is 43459.97 in 30 mins
2020-01-14 04:26:16 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-14 04:56:17 thread.c:204:calc_hashrate_avg: avg rate is 43361.97 in 30 mins
2020-01-14 04:56:17 temperature.c:450:temp_statistics_show:   pcb temp 40~55  chip temp 66~80
2020-01-14 05:26:18 thread.c:204:calc_hashrate_avg: avg rate is 43537.85 in 30 mins
2020-01-14 05:26:18 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-14 05:56:20 thread.c:204:calc_hashrate_avg: avg rate is 43637.74 in 30 mins
2020-01-14 05:56:20 temperature.c:450:temp_statistics_show:   pcb temp 40~55  chip temp 66~81
2020-01-14 06:26:21 thread.c:204:calc_hashrate_avg: avg rate is 43388.46 in 30 mins
2020-01-14 06:26:21 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-14 06:56:22 thread.c:204:calc_hashrate_avg: avg rate is 43335.47 in 30 mins
2020-01-14 06:56:22 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 65~80
2020-01-14 07:26:23 thread.c:204:calc_hashrate_avg: avg rate is 43245.02 in 30 mins
2020-01-14 07:26:23 temperature.c:450:temp_statistics_show:   pcb temp 40~54  chip temp 66~80
2020-01-14 07:56:25 thread.c:204:calc_hashrate_avg: avg rate is 43394.37 in 30 mins
2020-01-14 07:56:25 temperature.c:450:temp_statistics_show:   pcb temp 41~55  chip temp 66~80
2020-01-14 08:26:26 thread.c:204:calc_hashrate_avg: avg rate is 43291.17 in 30 mins
2020-01-14 08:26:26 temperature.c:450:temp_statistics_show:   pcb temp 41~55  chip temp 67~80

[1714903268]

1714903268

[BitMaxz]

I don't recommend to use nicehash pool because it will give you little reward compared to other pools. If you are having issue on Nicehash better use other mining pool for BTC.

Check other SHA256 pools from this link https://miningpoolstats.stream/bitcoin

or Try viaBTC pool it is better than Nicehash.

[Philipma1957cellphone]

Yeah the new firmware prevents nicehash due to.the constant switching nicehash causes.  I would not use nicehash with t17 t17e t17+ gear.

Or any type of.s17 gear.

[adamjamal]

Yeah the new firmware prevents nicehash due to.the constant switching nicehash causes.  I would not use nicehash with t17 t17e t17+ gear.

Or any type of.s17 gear.

so there is no way to use nice hash now ? is there a way to go back to my old firmware

I don't recommend to use nicehash pool because it will give you little reward compared to other pools. If you are having issue on Nicehash better use other mining pool for BTC.

Check other SHA256 pools from this link https://miningpoolstats.stream/bitcoin

or Try viaBTC pool it is better than Nicehash.

well it's the best from my perspective and i did try to compare it and found it gives me the highest reward i don't know how and why, thanks for the advice .

[BitMaxz]

You can downgrade it with signed firmware but it looks like Bitmain always remove older version from their download page.

Maybe some user here who use the same miner has a backup or older firmware version but I don't recommend to download them from unknown source unless if they have a bitmain direct link of older version.

[adamjamal]

You can downgrade it with signed firmware but it looks like Bitmain always remove older version from their download page.

Maybe some user here who use the same miner has a backup or older firmware version but I don't recommend to download them from unknown source unless if they have a bitmain direct link of older version.

if you mean using the upgrade process and choose the old firmware i already tried that and got this error (RUNME:cannot downgrade!!!) system upgrade failed , is there a way to bypass that

[BitMaxz]

if you mean using the upgrade process and choose the old firmware i already tried that and got this error (RUNME:cannot downgrade!!!) system upgrade failed , is there a way to bypass that

Are you sure about the firmware if it's a signed firmware?
if it's unsigned firmware it won't work but if you flash it with sig firmware it should be work.

Anyway, if your miner has an SD card slot you can try to contact bitmain and ask for an SD card image. I'm sure their image is a lower version.

You can follow this guide from here SD card flashing with customized PW

[mikeywith]

Yeah the new firmware prevents nicehash due to.the constant switching nicehash causes.  I would not use nicehash with t17 t17e t17+ gear.

Or any type of.s17 gear.

OP you should really pay close attention to this, switching coins is really bad for your miner, I heard this elsewhere before and I thought it was a complete bullshit until I experienced it myself, it was not with any SHA256 miner but with X11 and a couple of D3s, more than 50% of the hashboards that were mining on nicehash stopped working, the miners that were pointed to another pool mining dash directly lived a lot longer.

I have no technical explanations behind this, I am having a hard time saying this because it's hard to believe, I couldn't believe it when I heard it because it made no sense then, still makes no sense now to be honest, you either take my words for it, or simply ignore them.

[rocky2020]

You can downgrade it with signed firmware but it looks like Bitmain always remove older version from their download page.

Maybe some user here who use the same miner has a backup or older firmware version but I don't recommend to download them from unknown source unless if they have a bitmain direct link of older version.

if you use a non signed firmware ( like AsicTuner overclock ), it wont work on NiceHash ( maybe not compatible with their "Asicboost" ? ). But if you use original firmware, even the latest, it works perfectly.

To downgare, just recover 1st firmware ( not on their website, they removed it ), put on SD and flash it through the Sd reader.

[adamjamal]

if you use a non signed firmware ( like AsicTuner overclock ), it wont work on NiceHash ( maybe not compatible with their "Asicboost" ? ). But if you use original firmware, even the latest, it works perfectly.

To downgare, just recover 1st firmware ( not on their website, they removed it ), put on SD and flash it through the Sd reader.

do you have T17 miner with the latest update and nicehash do work for you ?

Are you sure about the firmware if it's a signed firmware?
if it's unsigned firmware it won't work but if you flash it with sig firmware it should be work.

Anyway, if your miner has an SD card slot you can try to contact bitmain and ask for an SD card image. I'm sure their image is a lower version.

You can follow this guide from here SD card flashing with customized PW

yeah i downloaded it from there website before the last one (i keep all the upgrade files on my pc), strange why i can't downgrade !
i will try the SD thing hope it will work, thank you .

[rocky2020]

i have latest T17 firmware and it work fine nicehash.  i tried overclock firmware, and in that case nicehash didn't reconized it

you have to do it by SD, bec it overide the downgrade protection.

[adamjamal]

i have latest T17 firmware and it work fine nicehash.  i tried overclock firmware, and in that case nicehash didn't reconized it

you have to do it by SD, bec it overide the downgrade protection.

you tried this version (Antminer-T17-user-OM-201912241613-sig_5047.tar.gz) with nicehash and it works ?
if that's the case can you please send me your kernel log file and how did you put the pools in the miner configurations same port for all the 3 or how, i will try exactly like you maybe it will work

[Artemis3]

Yeah the new firmware prevents nicehash due to.the constant switching nicehash causes.  I would not use nicehash with t17 t17e t17+ gear.

Or any type of.s17 gear.

Constant switching requires the use of #xnsub. Was this removed from newer gear?

I agree that nicehash isn't the best way of running a sha256 miner, and they have shady past record forcing loses to their clients when hacked, etc.

[supersonic]

just use stratum+tcp://sha256asicboost.EU.nicehash.com:3368
had same issue on my S17's
problem solved for me

[adamjamal]

just use stratum+tcp://sha256asicboost.EU.nicehash.com:3368
had same issue on my S17's
problem solved for me

Thank you only if you told me this earlier  , nicehash also give me this solution and it worked, after almost a week from talking about this problem .