T17/S17 malfunction: cases, solutions, remedies, RMA history

[TeslaWatt.com]

A new miner (T17+) only hashes on two boards out of three directly from the box.
Pure thievery as it would cost more to send it back than to keep hashing on two boards.

Not pleased.
DO NOT order T17+

They have RMA facility at "4704 Roseville Road, Suite 108, north highlands CA 95660". USPS should not be to expensive. Here you have more addresses you can ship to: https://support.bitmain.com/hc/en-us/articles/220138027-Global-repair-site-delivery-addresses.

[1714975072]

1714975072

[1714975072]

1714975072

[1714975072]

1714975072

[mikeywith]

He MUST create a repair ticket and only send the miner when instructed, he should also send the WHOLE miner and not just the bad hash boards, and if they don't receive it within 30 days from the day THEY shipped it from china, it will not be treated as DOA, if he sends it before 30 days have past - hey can still get paid for the shipping fees in the form of a coupon, so you want to make sure to use the fastest shipping method possible and not exceed the 30 days period if you want to be compensated for the shipping fees.

[TheYankeesWin!]

This is good info.  I have one of this missing a board units.

It worked for 26 days and now the one board is fuck you.

I will still be under warranty on may 15 which is the ½ ing  I may send it in then.

[jbillk]

I recently purchased a dead S17. the previous owner said this machine experienced problems with dropping hashboards right out of the box.

He RMA back to Bitmain. He eventually got it back, but only 2 hashbords were working. Eventually the other 2 went later on. I paid scrap value for it.

I changed out the data cables, re-flashed it, took it apart, tightened some connections, played with grounding, etc...

The log shows:

hashboard 0 has 0/48 chips detected
hashboard 1 has 40/48  chips detected
hashboard 2 has 32/48 chips detected

Shuts them all down.

I've been able to get 2 boards working by heating up the unit on startup. I basically put another miner's exhaust on the intake, and block the exhaust fans and get the unit very hot. Once it starts hashing i unblock the fans and remove from heat.

Seems like the boards are very sensitive to temperature on startup, so it may be worth trying if you have bricked units. it just frustrating because sometimes they work fine, and when i reboot they are dead again unless i do my startup procedure.

Now its running 2 of the boards, but randomly the second one drops out do to the temperature sensor issue.

[Scorpyy]

Im having identical issues. I own 2x T17+ units ( 2-3 months old ), and i am having issues with temp sensors.

One T17+ machine just dropped a temp sensor on 1 chain:

Code:

[2020/04/21 04:11:03] ERROR: src/temp.c:218 chain[0] sen[2] - Lost, no updates for 10 sec
[2020/04/21 04:11:03] ERROR: src/temp.c:218 chain[0] sen[3] - Lost, no updates for 10 sec
[2020/04/21 04:11:03] WARN: chain[0] - 2 sensor(s) reported their temps!
[2020/04/21 04:11:04] ERROR: src/temp.c:218 chain[0] sen[0] - Lost, no updates for 10 sec
[2020/04/21 04:11:04] ERROR: src/temp.c:218 chain[0] sen[1] - Lost, no updates for 10 sec
[2020/04/21 04:11:04] WARN: chain[0] - 0 sensor(s) reported their temps!
[2020/04/21 04:11:04] ERROR: driver-btm-chain.c:950 chain[0] - Failed to read temp from all sensors!
[2020/04/21 04:11:04] INFO: chain[0] - Shutting down the chain

I tried re-flashing with every possible firmware and issue persisted. Asic.to and Awesome miner firmwares helped me a lot since they auto restart on unbalance. So i usually let it run with 2 boards, however sometimes the third board re-appears but this time some of the chips have an X on them: https://prntscr.com/s5qm51 but im fine with this as long as it stays like this at least.

The 2nd T17+ machine - i tough i broke it. I was frustrated that my first T17+ machine is working at 2/3 of power so i decided to up-clock the other machine that was fully operational. But right after the tuning process, 2 sensors on the chain started dropping.

Code:

[2020/04/24 11:07:43] INFO: chain[2] - 44 chips detected
[2020/04/24 11:07:44] INFO: chain[1] - 44 chips detected
[2020/04/24 11:07:46] INFO: chain[0] - 44 chips detected
[2020/04/24 11:07:53] INFO: Start-up temperature is 24 C (min -15 C)
[2020/04/24 11:07:53] INFO: Switching to manual fan control (100 %)
[2020/04/24 11:07:53] INFO: Setting voltage from 19500 to 19300 mV gradually
[2020/04/24 11:08:11] INFO: Setting freq from 50 to 750 Mhz gradually
[2020/04/24 11:08:11] INFO: Warming up the chips
[2020/04/24 11:08:21] WARN: Target temp 85 C is too high
[2020/04/24 11:08:21] WARN: Overriding target temp to 77 C
[2020/04/24 11:08:21] INFO: Switching to automatic fan control (77 C)
[2020/04/24 11:08:21] INFO: Start mining!
[2020/04/24 11:08:35] ERROR: src/temp.c:218 chain[0] sen[2] - Lost, no updates for 10 sec
[2020/04/24 11:08:35] ERROR: src/temp.c:218 chain[0] sen[3] - Lost, no updates for 10 sec
[2020/04/24 11:08:35] WARN: chain[0] - 2 sensor(s) reported their temps!

As the machine was using Awesome miner firmware, which requires at least 1 sensor our of 4 to be operational i was confused why did the board drop? I contacted support and they are currently investigating this.

But then issue became worse:

Code:

[2020/04/25 02:50:15] INFO: chain[2] - Initializing
[2020/04/25 02:50:15] INFO: chain[1] - Initializing
[2020/04/25 02:50:15] INFO: chain[0] - Initializing
[2020/04/25 02:50:28] INFO: chain[2] - 44 chips detected
[2020/04/25 02:50:32] WARN: chain[1] - 40 of 44 chips detected
[2020/04/25 02:50:35] WARN: chain[0] - 14 of 44 chips detected
[2020/04/25 02:50:43] WARN: chain[1] - 40 of 44 chips detected
[2020/04/25 02:50:46] WARN: chain[0] - 14 of 44 chips detected
[2020/04/25 02:50:55] WARN: chain[1] - 40 of 44 chips detected
[2020/04/25 02:50:55] ERROR: driver-btm-chain.c:487 chain[1] - Failed to detect ASIC chips
[2020/04/25 02:50:55] INFO: chain[1] - Shutting down the chain
[2020/04/25 02:50:55] ERROR: driver-btm-base.c:358 chain[1] - Initialization failed
[2020/04/25 02:50:58] WARN: chain[0] - 14 of 44 chips detected
[2020/04/25 02:50:58] ERROR: driver-btm-chain.c:487 chain[0] - Failed to detect ASIC chips
[2020/04/25 02:50:58] INFO: chain[0] - Shutting down the chain

It now appeared that chips were dead on some boards. I tried switching slots and data cables, all pointed out to 2 dead boards. And this morning i was planning to open the machine and visually inspect if the chips were burnt and guess what? They re-appeared by themselves.

Code:

[2020/04/25 11:31:15] INFO: chain[2] - Initializing
[2020/04/25 11:31:15] INFO: chain[1] - Initializing
[2020/04/25 11:31:15] INFO: chain[0] - Initializing
[2020/04/25 11:31:28] INFO: chain[2] - 44 chips detected
[2020/04/25 11:31:29] INFO: chain[1] - 44 chips detected
[2020/04/25 11:31:30] INFO: chain[0] - 44 chips detected

However some of the chips have an X: https://prntscr.com/s5qp07

But still better then 1 board.

I also contacted Bitmain regarding temp sensors issue, they have told me to ship it back to China ( Europe office is closed due to pandemic ). I have decided to keep the half-working machines as shipping cost + possible complications were not worth it. If i encounter any more issues i will post it here. The post above that said he used to warm up the chips sounds interesting. I will give it a try if boards start dropping again.

T17e machine works fine for now.

[favebook]

Im having identical issues. I own 2x T17+ units ( 2-3 months old ), and i am having issues with temp sensors.

Try using Asic.to firmware and undervolt or overvolt it a bit. That seemed to be a fix in most instances. Also, if that does not work, try lower frequency with higher voltage.

[Scorpyy]

I have Awesome miner firmware currently, but it has the same options.

Here are results.

Starting point:

Pre-set profile @ 61 TH/s 700 Mhz 18.4 voltage = All boards and chips detected, sensors ok, some chips have an "X". Outcome 50 TH/s instead of 60 TH/s. No errors in kernel log

Undervolting:
700 Mhz with 17.8 voltage = chain[0] - 0 of 44 chips detected & chain[1] - 40 of 44 chips detected, shutted down both chains = 1 board operational - 20 TH/s
700 Mhz with 18.0 voltage = chain[0] - 0 of 44 chips detected & chain[1] - 40 of 44 chips detected, shutted down both chains = 1 board operational - 20 TH/s
700 Mhz with 18.2 voltage = 0 of 44 chips detected on 2 boards = 1 board operational, 20 TH/s

Overvolting:

700 Mhz with 18.5 voltage = chain[0] - 0 of 44 chips detected & chain[1] - 40 of 44 chips detected, shutted down both chains = 1 board operational - 20 TH/s
700 Mhz with 18.6 voltage = same as above.
700 Mhz with 18.8 voltage = same as above.

780 Mhz with 19.6 voltage = chain 0 and 1 0 of 44 chips detected. 1 board operational = 23 TH/s
800 Mhz with 19.5 voltage = same as above.
800 Mhz with 19.6 voltage = same as above.

Lowering hashrate:

600 Mhz with 18.4 voltage = chain[0] - 0 of 44 chips detected & chain[1] - 40 of 44 chips detected, shutted down both chains = 1 board operational
550 Mhz with 18.4 voltage = temps sensors error. 0 chains active. Machine is in a reboot loop.

Thing to note that even tho i changed frequency in settings it didn't change on machine, preset was disabled, chains set to "use global".
INFO: Setting freq from 50 to 695 Mhz gradually

and also voltage seems to be starting from same value anyway:
INFO: Setting voltage from 19500 to 18750 mV gradually

Ending point:

Pre-set profile @ 61 TH/s 700 Mhz 18.4 voltage - chain[0] - 0 of 44 chips detected & chain[1] - 40 of 44 chips detected, shutted down both chains = 1 board operational  20 TH/s

[favebook]

Try doing something insane like 600MHz and 18v or 700MHz and 19v to see if that wakes up hashboards. Or go even lower (something like 400/500 MHz with 17-19v).

[Scorpyy]

600 MHz - 18.0 v -  0 of 44 chips detected on 2 boards, 1 board boots up.

600 MHz - 19.0 v -chain[0] - 14 of 44 chain[1] - 0 of 44 chips detected, 1 board boots up.

400 MHz - 19.0 v - 0 of 44 chips detected on 2 boards. 1 board boots up.

I am wondering if i should try what jbillke did by warming up the chips during booting process. Is it safe to try 73 TH/s with 825 ? Is it safe to enable quiet fan on startup?

[favebook]

Yeah, it is safe to enable quiet fan on startup especially in your case...

Idk what your unit default settings are but T17+ are usually 58 TH/s... You can try going for 73, but if all other didn't work, I doubt that will, but please, do try.

Also, try warming up chips before turning machine on as he suggested, might work, but I doubt.

[mysticbitcoin]

Hey guys, I'm having an issue with a T17 40TH that I just picked up as well. I picked up a batch of three of them and two of them are hashing at 40TH no problem. One of them has been intermittent and ends up only doing 31TH, where the third board chain [2] is only hashing at 40% ~4TH. I've tried resetting the settings, then updating to the latest firmware from Bitmain, but same problem.

Kernel Log:

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 195068K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 34308K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 21268K (cc63c000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 4244297529
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 01559AD8-7B6A-42E6-A3FE-EDF3659527A9, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1052/338, WL threshold: 4096, image sequence number: 4185749592
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 4829CF2C-7435-4146-B2FD-0826AAE8443A, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2020-04-25 03:46:52 driver-btm-api.c:782:init_freq_mode: This is scan-user version
2020-04-25 03:46:52 driver-btm-api.c:2082:bitmain_soc_init: opt_multi_version     = 1
2020-04-25 03:46:52 driver-btm-api.c:2083:bitmain_soc_init: opt_bitmain_ab        = 1
2020-04-25 03:46:52 driver-btm-api.c:2084:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-04-25 03:46:52 driver-btm-api.c:2085:bitmain_soc_init: Miner compile time: Mon Jul 29 00:19:06 CST 2019 type: Antminer T17
2020-04-25 03:46:52 driver-btm-api.c:2086:bitmain_soc_init: commit version: e33ca6d 2019-07-18 12:39:03, build by: lol 2019-07-29 00:27:27
2020-04-25 03:46:52 driver-btm-api.c:1937:show_sn: no SN got, please write SN to /nvdata/sn
2020-04-25 03:46:52 driver-btm-api.c:1271:miner_device_init: Detect 256MB control board of XILINX
2020-04-25 03:46:52 driver-btm-api.c:1219:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-04-25 03:46:52 thread.c:745:create_read_nonce_reg_thread: create thread
2020-04-25 03:46:58 driver-btm-api.c:1203:init_miner_version: miner ID : 8042750618c0885c
2020-04-25 03:46:58 driver-btm-api.c:1209:init_miner_version: FPGA Version = 0xB013
2020-04-25 03:46:59 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-04-25 03:47:01 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-04-25 03:47:03 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-04-25 03:47:03 driver-btm-api.c:849:get_product_id: product_id[0] = 1
2020-04-25 03:47:03 driver-btm-api.c:849:get_product_id: product_id[1] = 1
2020-04-25 03:47:03 driver-btm-api.c:849:get_product_id: product_id[2] = 1
2020-04-25 03:47:03 driver-btm-api.c:1760:get_ccdly_opt: ccdly_opt[0] = 1
2020-04-25 03:47:03 driver-btm-api.c:1760:get_ccdly_opt: ccdly_opt[1] = 1
2020-04-25 03:47:03 driver-btm-api.c:1760:get_ccdly_opt: ccdly_opt[2] = 1
2020-04-25 03:47:03 driver-btm-api.c:1995:bitmain_board_init: g_ccdly_opt = 1
2020-04-25 03:47:03 driver-btm-api.c:795:_set_project_type: project:2
2020-04-25 03:47:03 driver-btm-api.c:825:_set_project_type: Project type: Antminer T17
2020-04-25 03:47:03 driver-btm-api.c:836:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-04-25 03:47:03 driver-btm-api.c:837:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-04-25 03:47:03 driver-btm-api.c:836:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-04-25 03:47:03 driver-btm-api.c:837:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-04-25 03:47:03 driver-btm-api.c:836:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-04-25 03:47:03 driver-btm-api.c:837:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-04-25 03:47:04 driver-btm-api.c:2015:bitmain_board_init: Fan check passed.
2020-04-25 03:47:04 register.c:283:get_register: !!! reg crc error
2020-04-25 03:47:06 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-04-25 03:47:09 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-04-25 03:47:11 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-04-25 03:47:14 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-04-25 03:47:16 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-04-25 03:47:20 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-04-25 03:47:20 thread.c:740:create_pic_heart_beat_thread: create thread
2020-04-25 03:47:20 power_api.c:55:power_init: power init ... 
2020-04-25 03:47:20 driver-btm-api.c:2025:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-04-25 03:47:52 power_api.c:231:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-04-25 03:47:57 power_api.c:123:check_voltage_multi: retry time: 0
2020-04-25 03:47:59 power_api.c:85:get_average_voltage: chain[0], voltage is: 17.909912 
2020-04-25 03:48:01 power_api.c:85:get_average_voltage: chain[1], voltage is: 17.358838 
2020-04-25 03:48:03 power_api.c:85:get_average_voltage: chain[2], voltage is: 17.218008 
2020-04-25 03:48:03 power_api.c:96:get_average_voltage: aveage voltage is: 17.495586 
2020-04-25 03:48:03 power_api.c:181:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-04-25 03:48:03 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-04-25 03:48:03 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-04-25 03:48:03 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-04-25 03:48:03 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-04-25 03:48:14 driver-btm-api.c:1146:check_asic_number_with_power_on: Chain[0]: find 29 asic, times 0
2020-04-25 03:48:24 driver-btm-api.c:1146:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 1
2020-04-25 03:48:34 driver-btm-api.c:1146:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-04-25 03:48:44 driver-btm-api.c:1146:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-04-25 03:48:48 driver-btm-api.c:339:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-04-25 03:48:48 driver-btm-api.c:339:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-04-25 03:48:48 driver-btm-api.c:339:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-04-25 03:48:48 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-04-25 03:48:48 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-04-25 03:48:48 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-04-25 03:48:48 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-04-25 03:48:48 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-04-25 03:48:48 driver-btm-api.c:1787:check_clock_counter: freq 50 clock_counter_limit 6
2020-04-25 03:48:49 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-04-25 03:48:49 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-04-25 03:48:49 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-04-25 03:48:49 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-04-25 03:48:49 voltage[0] = 1710
2020-04-25 03:48:49 voltage[1] = 1710
2020-04-25 03:48:49 voltage[2] = 1710
2020-04-25 03:48:49 power_api.c:139:set_working_voltage: working_voltage = 17.100000
2020-04-25 03:48:50 temperature.c:268:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-04-25 03:48:52 temperature.c:268:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-04-25 03:48:53 temperature.c:268:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-04-25 03:48:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-04-25 03:48:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-04-25 03:48:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-04-25 03:48:53 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-04-25 03:48:55 driver-btm-api.c:239:check_bringup_temp: Bring up temperature is 21
2020-04-25 03:48:55 thread.c:760:create_check_miner_status_thread: create thread
2020-04-25 03:48:55 thread.c:750:create_set_miner_status_thread: create thread
2020-04-25 03:48:55 driver-btm-api.c:732:calculate_timeout: dev->timeout = 392
2020-04-25 03:48:55 freq_tuning.c:152:freq_tuning_get_max_freq: Max freq of tuning is 760
2020-04-25 03:48:55 frequency.c:483:increase_freq_by_frequency_list_slowly: Increase freq slowly for all chain to 670
2020-04-25 03:48:55 frequency.c:340:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 50.000000 to 600.000000 @18.00V.
2020-04-25 03:48:55 frequency.c:341:auto_adaption_high_voltage_increase_frequency: index 0 1
2020-04-25 03:48:55 power_api.c:378:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-04-25 03:49:33 power_api.c:123:check_voltage_multi: retry time: 0
2020-04-25 03:49:34 power_api.c:85:get_average_voltage: chain[0], voltage is: 18.142588 
2020-04-25 03:49:36 power_api.c:85:get_average_voltage: chain[1], voltage is: 18.118095 
2020-04-25 03:49:38 power_api.c:85:get_average_voltage: chain[2], voltage is: 18.258926 
2020-04-25 03:49:38 power_api.c:96:get_average_voltage: aveage voltage is: 18.173203 
2020-04-25 03:49:38 driver-btm-api.c:662:increase_freq_slowly: init_freq = 50.00, final_freq = 600.00, freq_step = 5.00, chain = 255
2020-04-25 03:51:29 frequency.c:340:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 600.000000 to 650.000000 @18.00V.
2020-04-25 03:51:29 frequency.c:341:auto_adaption_high_voltage_increase_frequency: index 1 1
2020-04-25 03:51:29 driver-btm-api.c:662:increase_freq_slowly: init_freq = 600.00, final_freq = 650.00, freq_step = 5.00, chain = 255
2020-04-25 03:51:40 frequency.c:340:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 650.000000 to 670.000000 @18.00V.
2020-04-25 03:51:40 frequency.c:341:auto_adaption_high_voltage_increase_frequency: index 2 1
2020-04-25 03:51:40 driver-btm-api.c:662:increase_freq_slowly: init_freq = 650.00, final_freq = 670.00, freq_step = 5.00, chain = 255
2020-04-25 03:51:44 frequency.c:490:increase_freq_by_frequency_list_slowly: Increase freq slowly for chain 0 to 700
2020-04-25 03:51:44 frequency.c:340:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 670.000000 to 700.000000 @18.00V.
2020-04-25 03:51:44 frequency.c:341:auto_adaption_high_voltage_increase_frequency: index 2 1
2020-04-25 03:51:44 driver-btm-api.c:662:increase_freq_slowly: init_freq = 670.00, final_freq = 700.00, freq_step = 5.00, chain = 0
2020-04-25 03:51:50 driver-btm-api.c:763:set_timeout: freq 700 final timeout=168
2020-04-25 03:51:50 power_api.c:396:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.10 ...
2020-04-25 03:52:22 power_api.c:123:check_voltage_multi: retry time: 0
2020-04-25 03:52:24 power_api.c:85:get_average_voltage: chain[0], voltage is: 17.211885 
2020-04-25 03:52:26 power_api.c:85:get_average_voltage: chain[1], voltage is: 17.187392 
2020-04-25 03:52:27 power_api.c:85:get_average_voltage: chain[2], voltage is: 17.334345 
2020-04-25 03:52:27 power_api.c:96:get_average_voltage: aveage voltage is: 17.244541 
2020-04-25 03:52:27 frequency.c:582:get_current_min_freq: current min freq 670
2020-04-25 03:52:27 driver-btm-api.c:1787:check_clock_counter: freq 670 clock_counter_limit 85
2020-04-25 03:52:27 register.c:966:register_process_asic_response: Get another asic response: chain = 2, asic = 26
2020-04-25 03:52:27 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 5, core = 0, found 1, clock counter 0x00000000
2020-04-25 03:52:27 driver-btm-api.c:2179:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.
2020-04-25 03:52:27 thread.c:735:create_temperature_monitor_thread: create thread
2020-04-25 03:52:27 thread.c:755:create_check_system_status_thread: create thread
2020-04-25 03:52:28 driver-btm-api.c:2198:bitmain_soc_init: Init done!
2020-04-25 03:52:28 driver-btm-api.c:197:set_miner_status: STATUS_INIT
2020-04-25 03:52:32 driver-btm-api.c:197:set_miner_status: STATUS_OKAY
2020-04-25 03:52:37 driver-btm-api.c:1443:dhash_chip_send_job: Verion num 4
2020-04-25 03:57:37 thread.c:384:is_zero_nonce_happened: chain_nonce[0] = 15320
2020-04-25 03:57:37 thread.c:384:is_zero_nonce_happened: chain_nonce[1] = 14787
2020-04-25 03:57:37 thread.c:384:is_zero_nonce_happened: chain_nonce[2] = 12441
2020-04-25 03:57:37 thread.c:440:clear_zero_nonce_mark: 0 nonce protect succeed.

These screen shots are from before updating firmware:

https://drive.google.com/file/d/1g6OLOJpkJbIvsySUGZgQwTcQq2ywgsFV/view?usp=sharing
https://drive.google.com/file/d/1bgXIlyCkS8awDIgnV9w30f6BQCyrqgXO/view?usp=sharing

I've not run the machine for more than 30-40min just in case there could be any further damage. The third board just drops down and stays there! The message I see in the Kernel Log regarding Chain [2] is: 2020-04-25 03:52:27 register.c:966:register_process_asic_response: Get another asic response: chain = 2, asic = 26. What can should I do?

[favebook]

Probably dead chips. Either RMA, try custom firmware undervolt/overvolt or deal with it and keep it like that.

[jbillk]

I am wondering if i should try what jbillke did by warming up the chips during booting process.

I don't think the frequency and voltage adjustments will help if the chains aren't initialized. I haven't had much luck with that. Looks like in the log that the pre-heat, voltage tuning, and frequency tuning is done after the board detects all the chips are good to go.

Perhaps this is why i've had luck manually pre-heating the boards, as it gets them up to temperature before it attempts to detect all the asic chips. Try to get the startup temp to 75 C and see what happens.

Code:

[2020/04/25 19:41:01] ERROR: driver-btm-chain.c:487 chain[0] - Failed to detect ASIC chips
[2020/04/25 19:41:01] INFO: chain[0] - Shutting down the chain
[2020/04/25 19:41:02] ERROR: driver-btm-base.c:358 chain[0] - Initialization failed
[2020/04/25 19:41:05] INFO: Start-up temperature is 28 C (min -15 C)
[2020/04/25 19:41:05] INFO: Switching to manual fan control (100 %)
[2020/04/25 19:41:05] INFO: Setting voltage from 21000 to 19400 mV gradually
[2020/04/25 19:41:33] INFO: Setting freq from 50 to 700 Mhz gradually
[2020/04/25 19:41:33] INFO: Warming up the chips
[2020/04/25 19:41:41] INFO: Switching to automatic fan control (75 C)
[2020/04/25 19:41:41] INFO: Start mining!
[2020/04/25 19:42:41] INFO: Setting voltage from 19400 to 19200 mV gradually
[2020/04/25 19:43:03] INFO: Setting voltage from 19200 to 19000 mV gradually
[2020/04/25 19:43:26] INFO: Setting voltage from 19000 to 18800 mV gradually

[Scorpyy]

I have succeeded to get the 2nd board operational by heating up the machine ( previously he saw 40 of 44 chips and when heated 44/44 ). But it was just a matter of time before it dropped out again. I found out that you can do the same thing with his original paper box if miner can see at least 1 board. ( upclock board, cover with a box, let it run for 10s, unplug from wall socket, re-plug again ).

On the other machine i found the best solution to be the following:

• Machine usually works with 2/3 boards only.
• Up-clock the unit to 800 Mhz.
• Set Disable chips at 92 C.
• Set the unit to downscale if chip overheat.
• Quiet fan mode at startup.
• After it restarts all 3 hashboards are visible ( for a 12hr or a day ).
• Up-clock to 800mhz again but select Pre-save option this time.

Code:

[2020/05/01 17:35:06] INFO: Power ON
[2020/05/01 17:35:08] INFO: Starting FPGA queue
[2020/05/01 17:35:08] INFO: Initializing hash boards
[2020/05/01 17:35:08] INFO: chain[2] - Initializing
[2020/05/01 17:35:08] INFO: chain[1] - Initializing
[2020/05/01 17:35:08] INFO: chain[0] - Initializing
[2020/05/01 17:35:22] INFO: chain[2] - 44 chips detected
[2020/05/01 17:35:23] INFO: chain[1] - 44 chips detected
[2020/05/01 17:35:24] ERROR: src/chip139x.c:1006 chain[0] - Failed to receive chip replies
[2020/05/01 17:35:25] ERROR: src/chip139x.c:1006 chain[0] - Failed to receive chip replies
[2020/05/01 17:35:26] ERROR: src/chip139x.c:1006 chain[0] - Failed to receive chip replies
[2020/05/01 17:35:26] WARN: chain[0] - 0 of 44 chips detected
[2020/05/01 17:35:49] ERROR: driver-btm-chain.c:487 chain[0] - Failed to detect ASIC chips
[2020/05/01 17:35:49] INFO: chain[0] - Shutting down the chain
[2020/05/01 17:35:50] ERROR: driver-btm-base.c:358 chain[0] - Initialization failed
[2020/05/01 17:35:53] INFO: Start-up temperature is 22 C (min -15 C)
[2020/05/01 17:35:53] INFO: Activating silent start-up mode
[2020/05/01 17:35:53] INFO: Switching to warm-up fan control (62 C)
[2020/05/01 17:35:53] INFO: Setting voltage from 19500 to 19800 mV gradually
[2020/05/01 17:36:15] INFO: Setting freq from 50 to 800 Mhz gradually
[2020/05/01 17:36:15] INFO: Warming up the chips
[2020/05/01 17:36:24] INFO: Switching to automatic fan control (80 C)
[2020/05/01 17:36:24] INFO: Start mining!
[2020/05/01 17:37:24] INFO: Setting voltage from 19800 to 19600 mV gradually
[2020/05/01 17:37:47] INFO: Setting voltage from 19600 to 19400 mV gradually
[2020/05/02 06:11:10] WARN: chain[1] - Overheated, chip temp=92
[2020/05/02 06:11:10] WARN: Switching to emergency fan control
[2020/05/02 06:11:10] INFO: chain[1] - Shutting down the chain
[2020/05/02 06:11:10] INFO: Shutting down the miner
[2020/05/02 06:11:11] INFO: Stopping FPGA queue
[2020/05/02 06:11:11] INFO: chain[0] - Shutting down the chain
[2020/05/02 06:11:11] INFO: chain[1] - Shutting down the chain
[2020/05/02 06:11:11] INFO: chain[2] - Shutting down the chain
[2020/05/02 06:11:11] INFO: Power OFF
[2020/05/02 06:11:27] INFO: Detected 256 Mb of RAM
[2020/05/02 06:11:27] INFO: Switching to manual fan control (30 %)
[2020/05/02 06:11:27] INFO: Checking fans
[2020/05/02 06:11:27] INFO: fan[0] - OK
[2020/05/02 06:11:27] INFO: fan[1] - OK
[2020/05/02 06:11:27] INFO: fan[2] - OK
[2020/05/02 06:11:27] INFO: fan[3] - OK
[2020/05/02 06:11:33] INFO: Power ON
[2020/05/02 06:11:35] INFO: Starting FPGA queue
[2020/05/02 06:11:35] INFO: Initializing hash boards
[2020/05/02 06:11:35] INFO: chain[2] - Initializing
[2020/05/02 06:11:35] INFO: chain[1] - Initializing
[2020/05/02 06:11:35] INFO: chain[0] - Initializing
[2020/05/02 06:11:48] INFO: chain[2] - 44 chips detected
[2020/05/02 06:11:49] INFO: chain[1] - 44 chips detected
[2020/05/02 06:11:50] INFO: chain[0] - 44 chips detected
[2020/05/02 06:11:57] INFO: Start-up temperature is 24 C (min -15 C)
[2020/05/02 06:11:57] INFO: Activating silent start-up mode
[2020/05/02 06:11:57] INFO: Switching to warm-up fan control (62 C)
[2020/05/02 06:11:57] INFO: Setting voltage from 19500 to 19300 mV gradually
[2020/05/02 06:12:15] INFO: Setting freq from 50 to 750 Mhz gradually
[2020/05/02 06:12:15] INFO: Warming up the chips
[2020/05/02 06:12:25] INFO: Switching to automatic fan control (80 C)
[2020/05/02 06:12:25] INFO: Start mining!

[PopoJeff]

What fresh hell is this?

Ran fine for about 16hrs out of the box.... then I dropped one board due to the temp sensor error.  Now this crc error.    Been thru about a dozen reboots.  Comes up runs all 3 boards fine for about 20 min, then drops the one.  Also did a reset via interface.

Code:

2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error
2020-05-03 00:25:10 register.c:306:get_register: !!! reg crc error

Code:

2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 679740416
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 545719296
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 1049232384
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 898434048
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 663749632
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 798163968
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 932578304
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 983106560
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 580649984
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 715064320
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 547488768
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 732234752
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 900203520
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 1034617856
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 632161280
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 615580672
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 1018430464
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 884409344
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 716833792
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 566035456
2020-05-03 00:31:23 register.c:313:get_register: !!! REG_TYPE = 1. 1052771328
2020-05-03 00:32:00 register.c:313:get_register: !!! REG_TYPE = 1. 806683648
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 806683648
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 773325824
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 639304704
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 1042154496
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 656475136
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 1059324928
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 925303808
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 690619392
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 573375488
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 808453120
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 942867456
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 540410880
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 758711296
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 893125632
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 1027539968
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 574751744
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 692388864
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 927466496
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 1061880832
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 659424256
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 642843648
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 1045693440
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 911672320
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 676987904
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 593298432
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 694158336
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 560137216
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 962987008
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 879297536
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 745276416
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 611255296
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 913441792
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 1031078912
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 595067904
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 729482240
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 863896576
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 813761536
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 679740416
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 545719296
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 1049232384
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 898434048
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 663749632
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 798163968
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 932578304
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 983106560
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 580649984
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 715064320
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 547488768
2020-05-03 00:32:51 register.c:313:get_register: !!! REG_TYPE = 1. 732234752

Code:

2020-05-03 00:34:51 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2020-05-03 00:34:52 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2020-05-03 00:34:52 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0
2020-05-03 00:34:52 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
2020-05-03 00:34:52 thread.c:996:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 0 times.
2020-05-03 00:34:53 thread.c:976:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 13, require 65, failed times 1: ooooo ooxxx ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2020-05-03 00:34:54 thread.c:996:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 1 times.
2020-05-03 00:34:55 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2020-05-03 00:34:55 thread.c:976:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 13, require 65, failed times 1: ooooo ooxxx ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2020-05-03 00:34:55 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2020-05-03 00:34:55 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0
2020-05-03 00:34:56 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
2020-05-03 00:34:56 thread.c:996:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 2 times.
2020-05-03 00:34:57 thread.c:976:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 13, require 65, failed times 1: ooooo ooxxx ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2020-05-03 00:34:58 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2020-05-03 00:34:58 thread.c:996:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 3 times.
2020-05-03 00:34:59 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2020-05-03 00:34:59 thread.c:976:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 13, require 65, failed times 1: ooooo ooxxx ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2020-05-03 00:34:59 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0
2020-05-03 00:34:59 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
2020-05-03 00:35:01 thread.c:996:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 4 times.
2020-05-03 00:35:01 thread.c:976:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 13, require 65, failed times 1: ooooo ooxxx ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2020-05-03 00:35:02 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2020-05-03 00:35:02 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2020-05-03 00:35:03 thread.c:996:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 5 times.
2020-05-03 00:35:03 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0
2020-05-03 00:35:03 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
2020-05-03 00:35:03 thread.c:976:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 13, require 65, failed times 1: ooooo ooxxx ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2020-05-03 00:35:05 thread.c:996:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 6 times.
2020-05-03 00:35:05 thread.c:976:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 13, require 65, failed times 1: ooooo ooxxx ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2020-05-03 00:35:05 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2020-05-03 00:35:06 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2020-05-03 00:35:06 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0
2020-05-03 00:35:06 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
2020-05-03 00:35:07 thread.c:996:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 7 times.
2020-05-03 00:35:07 thread.c:976:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 13, require 65, failed times 1: ooooo ooxxx ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2020-05-03 00:35:09 thread.c:996:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 8 times.
2020-05-03 00:35:09 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2020-05-03 00:35:09 thread.c:976:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 13, require 65, failed times 1: ooooo ooxxx ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2020-05-03 00:35:09 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2020-05-03 00:35:10 temperature.c:838:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0

[mysticbitcoin]

Hey, Guys did a full cleaning on this T17  and found that it was running at Full Hash speed for a while, but started going down hill fast!

Here is the Kernel Log: (Before it rebooted)

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203756K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25620K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12580K (cceb8000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 4244297529
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 01559AD8-7B6A-42E6-A3FE-EDF3659527A9, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1052/338, WL threshold: 4096, image sequence number: 4185749592
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 4829CF2C-7435-4146-B2FD-0826AAE8443A, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2020-04-29 16:46:29 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2020-04-29 16:46:29 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2020-04-29 16:46:29 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2020-04-29 16:46:29 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-04-29 16:46:29 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2020-04-29 16:46:29 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2020-04-29 16:46:29 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2020-04-29 16:46:29 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2020-04-29 16:46:29 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-04-29 16:46:29 thread.c:789:create_read_nonce_reg_thread: create thread
2020-04-29 16:46:35 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-04-29 16:46:35 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-04-29 16:46:37 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-04-29 16:46:39 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-04-29 16:46:40 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-04-29 16:46:40 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-04-29 16:46:40 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-04-29 16:46:40 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-04-29 16:46:40 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-04-29 16:46:40 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-04-29 16:46:40 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-04-29 16:46:40 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-04-29 16:46:40 driver-btm-api.c:644:_set_project_type: project:2
2020-04-29 16:46:40 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-04-29 16:46:40 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-04-29 16:46:40 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-04-29 16:46:40 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-04-29 16:46:40 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-04-29 16:46:40 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-04-29 16:46:40 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-04-29 16:46:42 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-04-29 16:46:42 register.c:283:get_register: !!! reg crc error
2020-04-29 16:46:44 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-04-29 16:46:48 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-04-29 16:46:49 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-04-29 16:46:53 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-04-29 16:46:55 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-04-29 16:46:58 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-04-29 16:46:58 thread.c:784:create_pic_heart_beat_thread: create thread
2020-04-29 16:46:58 power_api.c:55:power_init: power init ... 
2020-04-29 16:46:58 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-04-29 16:47:30 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-04-29 16:47:36 power_api.c:124:check_voltage_multi: retry time: 0
2020-04-29 16:47:38 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.903789 
2020-04-29 16:47:39 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.352715 
2020-04-29 16:47:41 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.211885 
2020-04-29 16:47:41 power_api.c:97:get_average_voltage: aveage voltage is: 17.489463 
2020-04-29 16:47:41 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-04-29 16:47:41 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-04-29 16:47:41 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-04-29 16:47:41 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-04-29 16:47:41 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-04-29 16:47:53 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-04-29 16:48:03 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-04-29 16:48:13 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-04-29 16:48:16 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-04-29 16:48:16 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-04-29 16:48:17 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-04-29 16:48:17 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-04-29 16:48:17 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-04-29 16:48:17 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-04-29 16:48:17 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-04-29 16:48:17 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-04-29 16:48:17 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-04-29 16:48:17 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-04-29 16:48:17 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-04-29 16:48:17 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-04-29 16:48:17 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-04-29 16:48:17 voltage[0] = 1710
2020-04-29 16:48:17 voltage[1] = 1710
2020-04-29 16:48:17 voltage[2] = 1710
2020-04-29 16:48:17 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-04-29 16:48:19 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-04-29 16:48:20 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-04-29 16:48:22 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-04-29 16:48:22 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-04-29 16:48:22 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-04-29 16:48:22 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-04-29 16:48:22 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-04-29 16:48:23 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 19
2020-04-29 16:48:23 thread.c:804:create_check_miner_status_thread: create thread
2020-04-29 16:48:23 thread.c:794:create_set_miner_status_thread: create thread
2020-04-29 16:48:23 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-04-29 16:48:23 thread.c:779:create_temperature_monitor_thread: create thread
2020-04-29 16:48:23 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2020-04-29 16:48:23 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-04-29 16:48:56 power_api.c:124:check_voltage_multi: retry time: 0
2020-04-29 16:48:58 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.142588 
2020-04-29 16:48:59 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.148711 
2020-04-29 16:49:01 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.271172 
2020-04-29 16:49:01 power_api.c:97:get_average_voltage: aveage voltage is: 18.187490 
2020-04-29 16:49:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-04-29 16:49:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-04-29 16:49:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-04-29 16:49:01 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-04-29 16:49:02 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-04-29 16:49:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-04-29 16:49:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-04-29 16:49:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-04-29 16:49:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-04-29 16:49:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-04-29 16:49:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-04-29 16:49:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-04-29 16:49:03 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-04-29 16:49:03 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-04-29 16:49:04 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-04-29 16:49:05 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-04-29 16:49:05 power_api.c:146:set_higher_voltage: higher_voltage = 18.000000
2020-04-29 16:49:05 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 18.00 ...
2020-04-29 16:49:29 power_api.c:124:check_voltage_multi: retry time: 0
2020-04-29 16:49:31 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.154834 
2020-04-29 16:49:32 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.130342 
2020-04-29 16:49:34 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.246679 
2020-04-29 16:49:34 power_api.c:97:get_average_voltage: aveage voltage is: 18.177285 
2020-04-29 16:49:34 frequency.c:540:get_current_min_freq: current min freq 670
2020-04-29 16:49:34 driver-btm-api.c:1660:check_clock_counter: freq 670 clock_counter_limit 85
2020-04-29 16:49:35 register.c:966:register_process_asic_response: Get another asic response: chain = 2, asic = 26
2020-04-29 16:49:35 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 20, core = 105, found 1, clock counter 0x00000000
2020-04-29 16:49:35 driver-btm-api.c:2097:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.
2020-04-29 16:49:35 thread.c:799:create_check_system_status_thread: create thread
2020-04-29 16:49:36 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2020-04-29 16:49:36 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2020-04-29 16:49:40 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-04-29 16:49:50 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
2020-04-29 16:49:54 thread.c:382:check_working_voltage: current PCB min temperature is 43
2020-04-29 16:49:54 thread.c:383:check_working_voltage: current voltage is 18.00V, recovery to 17.10V
2020-04-29 16:49:54 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.10 ...
2020-04-29 16:50:28 power_api.c:124:check_voltage_multi: retry time: 0
2020-04-29 16:50:30 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.211885 
2020-04-29 16:50:31 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.175146 
2020-04-29 16:50:33 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.309853 
2020-04-29 16:50:33 power_api.c:97:get_average_voltage: aveage voltage is: 17.232295 
2020-04-29 16:55:32 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 17383
2020-04-29 16:55:32 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 16885
2020-04-29 16:55:32 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 14342
2020-04-29 16:55:32 thread.c:478:clear_zero_nonce_mark: 0 nonce protect succeed.
2020-04-29 17:20:33 thread.c:204:calc_hashrate_avg: avg rate is 39133.01 in 30 mins
2020-04-29 17:20:33 temperature.c:450:temp_statistics_show:   pcb temp 41~56  chip temp 62~79
2020-04-29 17:20:33 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 17:20:33 thread.c:286:check_hashrate: current PCB min temperature 41
2020-04-29 17:20:33 thread.c:287:check_hashrate: current voltage is 17.10V, working voltage is 17.10V
2020-04-29 17:20:33 thread.c:318:check_hashrate: high temp, increase voltage 0.1V/0.2V to 17.20V
2020-04-29 17:20:33 driver-btm-api.c:2124:bitmain_reopen_core: reopen_core start!
2020-04-29 17:20:40 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-04-29 17:20:40 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-04-29 17:20:41 chain = 0, mode = 0, load_done = false.
2020-04-29 17:20:41 chain = 1, mode = 0, load_done = false.
2020-04-29 17:20:41 chain = 2, mode = 0, load_done = false.
2020-04-29 17:20:42 chain = 0, mode = 0, load_done = false.
2020-04-29 17:20:42 chain = 1, mode = 0, load_done = false.
2020-04-29 17:20:42 chain = 2, mode = 0, load_done = false.
2020-04-29 17:20:42 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-04-29 17:20:43 chain = 0, mode = 0, load_done = false.
2020-04-29 17:20:43 chain = 1, mode = 0, load_done = false.
2020-04-29 17:20:43 chain = 2, mode = 0, load_done = false.
2020-04-29 17:20:44 chain = 0, mode = 0, load_done = false.
2020-04-29 17:20:44 chain = 1, mode = 0, load_done = false.
2020-04-29 17:20:44 chain = 2, mode = 0, load_done = false.
2020-04-29 17:20:44 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-04-29 17:20:45 chain = 0, mode = 0, load_done = false.
2020-04-29 17:20:45 chain = 1, mode = 0, load_done = false.
2020-04-29 17:20:45 chain = 2, mode = 0, load_done = false.
2020-04-29 17:20:46 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-04-29 17:20:46 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-04-29 17:20:46 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-04-29 17:20:46 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-04-29 17:20:46 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-04-29 17:20:46 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-04-29 17:20:46 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-04-29 17:20:46 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-04-29 17:20:46 driver-btm-api.c:644:_set_project_type: project:2
2020-04-29 17:20:46 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-04-29 17:20:46 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-04-29 17:20:46 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-04-29 17:20:46 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-04-29 17:20:46 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-04-29 17:20:46 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-04-29 17:20:46 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-04-29 17:20:48 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
[color=red][b]2020-04-29 17:20:49 register.c:283:get_register: !!! reg crc error[/b][/color]
2020-04-29 17:20:51 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-04-29 17:20:54 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-04-29 17:20:56 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-04-29 17:21:00 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-04-29 17:21:03 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-04-29 17:21:09 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-04-29 17:21:09 power_api.c:55:power_init: power init ... 
2020-04-29 17:21:09 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-04-29 17:21:41 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-04-29 17:21:43 power_api.c:124:check_voltage_multi: retry time: 0
2020-04-29 17:21:44 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.199638 
2020-04-29 17:21:46 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.113916 
2020-04-29 17:21:48 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.236377 
2020-04-29 17:21:48 power_api.c:97:get_average_voltage: aveage voltage is: 17.183310 
2020-04-29 17:21:48 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-04-29 17:21:48 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-04-29 17:21:48 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-04-29 17:21:48 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-04-29 17:21:48 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-04-29 17:21:58 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 29 asic, times 0
2020-04-29 17:22:08 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 1
2020-04-29 17:22:18 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-04-29 17:22:29 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-04-29 17:22:32 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-04-29 17:22:32 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-04-29 17:22:32 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-04-29 17:22:33 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-04-29 17:22:33 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-04-29 17:22:33 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-04-29 17:22:33 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-04-29 17:22:33 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-04-29 17:22:33 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-04-29 17:22:33 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-04-29 17:22:33 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-04-29 17:22:33 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-04-29 17:22:33 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-04-29 17:22:33 voltage[0] = 1710
2020-04-29 17:22:33 voltage[1] = 1710
2020-04-29 17:22:33 voltage[2] = 1710
2020-04-29 17:22:33 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-04-29 17:22:35 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-04-29 17:22:36 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-04-29 17:22:37 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-04-29 17:22:37 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-04-29 17:22:37 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-04-29 17:22:37 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-04-29 17:22:37 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-04-29 17:22:39 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 18
2020-04-29 17:22:39 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-04-29 17:22:39 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-04-29 17:23:15 power_api.c:124:check_voltage_multi: retry time: 0
2020-04-29 17:23:17 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.136465 
2020-04-29 17:23:19 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.118095 
2020-04-29 17:23:20 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.228310 
2020-04-29 17:23:20 power_api.c:97:get_average_voltage: aveage voltage is: 18.160957 
2020-04-29 17:23:20 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-04-29 17:23:21 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-04-29 17:23:21 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-04-29 17:23:21 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-04-29 17:23:21 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-04-29 17:23:21 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-04-29 17:23:21 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-04-29 17:23:21 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-04-29 17:23:21 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-04-29 17:23:21 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-04-29 17:23:22 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-04-29 17:23:23 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-04-29 17:23:23 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-04-29 17:23:23 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-04-29 17:23:23 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-04-29 17:23:23 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-04-29 17:23:23 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-04-29 17:23:23 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-04-29 17:23:23 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-04-29 17:23:23 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-04-29 17:23:24 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-04-29 17:23:24 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-04-29 17:23:24 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-04-29 17:23:24 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-04-29 17:23:24 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-04-29 17:23:24 power_api.c:146:set_higher_voltage: higher_voltage = 18.000000
2020-04-29 17:23:24 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 18.00 ...
2020-04-29 17:23:48 power_api.c:124:check_voltage_multi: retry time: 0
2020-04-29 17:23:50 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.118095 
2020-04-29 17:23:52 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.118095 
2020-04-29 17:23:54 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.240556 
2020-04-29 17:23:54 power_api.c:97:get_average_voltage: aveage voltage is: 18.158916 
2020-04-29 17:23:54 driver-btm-api.c:2186:bitmain_reopen_core: reopen_core done!
2020-04-29 17:23:54 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.20 ...
2020-04-29 17:24:34 power_api.c:124:check_voltage_multi: retry time: 0
2020-04-29 17:24:36 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.303730 
2020-04-29 17:24:38 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.273115 
2020-04-29 17:24:40 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.401699 
2020-04-29 17:24:40 power_api.c:97:get_average_voltage: aveage voltage is: 17.326181 
2020-04-29 17:24:40 power_api.c:140:set_working_voltage: working_voltage = 17.200001
2020-04-29 17:29:39 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 112803
2020-04-29 17:29:39 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 107268
2020-04-29 17:29:39 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 91851
2020-04-29 17:54:40 thread.c:204:calc_hashrate_avg: avg rate is 39117.71 in 30 mins
2020-04-29 17:54:40 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 63~80
2020-04-29 17:54:40 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 17:54:40 thread.c:286:check_hashrate: current PCB min temperature 42
2020-04-29 17:54:40 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-04-29 17:54:40 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-04-29 18:24:41 thread.c:204:calc_hashrate_avg: avg rate is 39320.85 in 30 mins
2020-04-29 18:24:41 temperature.c:450:temp_statistics_show:   pcb temp 42~57  chip temp 63~81
2020-04-29 18:54:42 thread.c:204:calc_hashrate_avg: avg rate is 39045.15 in 30 mins
2020-04-29 18:54:42 temperature.c:450:temp_statistics_show:   pcb temp 42~57  chip temp 63~80
2020-04-29 18:54:42 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 18:54:42 thread.c:286:check_hashrate: current PCB min temperature 42
2020-04-29 18:54:42 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-04-29 18:54:42 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-04-29 19:24:44 thread.c:204:calc_hashrate_avg: avg rate is 39035.09 in 30 mins
2020-04-29 19:24:44 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 63~81
2020-04-29 19:24:44 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 19:24:44 thread.c:286:check_hashrate: current PCB min temperature 42
2020-04-29 19:24:44 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-04-29 19:24:44 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-04-29 19:54:45 thread.c:204:calc_hashrate_avg: avg rate is 38942.28 in 30 mins
2020-04-29 19:54:45 temperature.c:450:temp_statistics_show:   pcb temp 42~57  chip temp 63~81
2020-04-29 19:54:45 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 19:54:45 thread.c:286:check_hashrate: current PCB min temperature 42
2020-04-29 19:54:45 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-04-29 19:54:45 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-04-29 20:24:46 thread.c:204:calc_hashrate_avg: avg rate is 39099.22 in 30 mins
2020-04-29 20:24:46 temperature.c:450:temp_statistics_show:   pcb temp 43~57  chip temp 63~80
2020-04-29 20:24:46 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 20:24:46 thread.c:286:check_hashrate: current PCB min temperature 43
2020-04-29 20:24:46 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-04-29 20:24:46 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-04-29 20:54:48 thread.c:204:calc_hashrate_avg: avg rate is 39243.94 in 30 mins
2020-04-29 20:54:48 temperature.c:450:temp_statistics_show:   pcb temp 43~57  chip temp 64~80
2020-04-29 21:24:49 thread.c:204:calc_hashrate_avg: avg rate is 39079.01 in 30 mins
2020-04-29 21:24:49 temperature.c:450:temp_statistics_show:   pcb temp 43~57  chip temp 64~80
2020-04-29 21:24:49 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 21:24:49 thread.c:286:check_hashrate: current PCB min temperature 43
2020-04-29 21:24:49 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-04-29 21:24:49 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-04-29 21:54:50 thread.c:204:calc_hashrate_avg: avg rate is 39195.28 in 30 mins
2020-04-29 21:54:50 temperature.c:450:temp_statistics_show:   pcb temp 43~57  chip temp 64~80
2020-04-29 21:54:50 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 21:54:50 thread.c:286:check_hashrate: current PCB min temperature 43
2020-04-29 21:54:50 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-04-29 21:54:50 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-04-29 22:24:52 thread.c:204:calc_hashrate_avg: avg rate is 39376.48 in 30 mins
2020-04-29 22:24:52 temperature.c:450:temp_statistics_show:   pcb temp 44~56  chip temp 66~80
2020-04-29 22:54:53 thread.c:204:calc_hashrate_avg: avg rate is 39147.83 in 30 mins
2020-04-29 22:54:53 temperature.c:450:temp_statistics_show:   pcb temp 43~55  chip temp 64~79
2020-04-29 22:54:53 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 22:54:53 thread.c:286:check_hashrate: current PCB min temperature 43
2020-04-29 22:54:53 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-04-29 22:54:53 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-04-29 23:24:54 thread.c:204:calc_hashrate_avg: avg rate is 39294.97 in 30 mins
2020-04-29 23:24:54 temperature.c:450:temp_statistics_show:   pcb temp 43~57  chip temp 64~80
2020-04-29 23:54:55 thread.c:204:calc_hashrate_avg: avg rate is 38966.09 in 30 mins
2020-04-29 23:54:55 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 63~79
2020-04-29 23:54:55 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-04-29 23:54:55 thread.c:286:check_hashrate: current PCB min temperature 42
2020-04-29 23:54:55 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-04-29 23:54:55 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V

Pictures of the Miner Status:

https://drive.google.com/file/d/1o0hf-1KdEfxtyAs3ewfT3x7gPbpxzBXL/view?usp=sharing
https://drive.google.com/open?id=1vJ8PzxGsONfzU43RouEbhy9a4RUeB9Mw

Things to Note in the Kernel Log:

1.)

Code:

2020-04-29 16:49:35 register.c:966:register_process_asic_response: Get another asic response: chain = 2, asic = 26
2020-04-29 16:49:35 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 20, core = 105, found 1, clock counter 0x00000000
2020-04-29 16:49:35 driver-btm-api.c:2097:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.

2.)

Code:

2020-04-29 17:20:49 register.c:283:get_register: !!! reg crc error

3.)

Code:

2020-04-29 17:20:33 thread.c:318:check_hashrate: high temp, increase voltage 0.1V/0.2V to 17.20V
2020-04-29 17:20:33 driver-btm-api.c:2124:bitmain_reopen_core: reopen_core start!

2020-04-29 17:54:40 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V - (Continually shows until it finally reboots)

[mysticbitcoin]

Ok, So it's official the 3rd Hash Board just died (Chain [2]). Here is the slow death of the Hash Board, starts operating at half hash. after this:

Kernel Log:

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203756K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25620K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12580K (cceb8000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 4244297529
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 01559AD8-7B6A-42E6-A3FE-EDF3659527A9, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1052/339, WL threshold: 4096, image sequence number: 4185749592
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 4829CF2C-7435-4146-B2FD-0826AAE8443A, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
1970-01-01 00:05:54 driver-btm-api.c:631:init_freq_mode: This is scan-user version
1970-01-01 00:05:54 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
1970-01-01 00:05:54 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
1970-01-01 00:05:54 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
1970-01-01 00:05:54 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
1970-01-01 00:05:54 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
1970-01-01 00:05:54 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
1970-01-01 00:05:54 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
1970-01-01 00:05:54 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
1970-01-01 00:05:54 thread.c:789:create_read_nonce_reg_thread: create thread
1970-01-01 00:06:00 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
1970-01-01 00:06:00 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
1970-01-01 00:06:02 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
1970-01-01 00:06:04 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
1970-01-01 00:06:05 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
1970-01-01 00:06:05 driver-btm-api.c:705:get_product_id: product_id[0] = 1
1970-01-01 00:06:05 driver-btm-api.c:705:get_product_id: product_id[1] = 1
1970-01-01 00:06:05 driver-btm-api.c:705:get_product_id: product_id[2] = 1
1970-01-01 00:06:05 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
1970-01-01 00:06:05 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
1970-01-01 00:06:05 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
1970-01-01 00:06:05 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
1970-01-01 00:06:05 driver-btm-api.c:644:_set_project_type: project:2
1970-01-01 00:06:05 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
1970-01-01 00:06:05 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
1970-01-01 00:06:05 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
1970-01-01 00:06:05 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
1970-01-01 00:06:05 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
1970-01-01 00:06:05 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
1970-01-01 00:06:05 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
1970-01-01 00:06:07 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
1970-01-01 00:06:08 register.c:283:get_register: !!! reg crc error
1970-01-01 00:06:09 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
1970-01-01 00:06:13 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
1970-01-01 00:06:14 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
1970-01-01 00:06:18 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
1970-01-01 00:06:20 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
1970-01-01 00:06:23 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
1970-01-01 00:06:23 thread.c:784:create_pic_heart_beat_thread: create thread
1970-01-01 00:06:23 power_api.c:55:power_init: power init ... 
1970-01-01 00:06:23 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
1970-01-01 00:06:55 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
1970-01-01 00:07:01 power_api.c:124:check_voltage_multi: retry time: 0
1970-01-01 00:07:03 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.916035 
1970-01-01 00:07:04 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.364961 
1970-01-01 00:07:06 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.242500 
1970-01-01 00:07:06 power_api.c:97:get_average_voltage: aveage voltage is: 17.507832 
1970-01-01 00:07:06 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
1970-01-01 00:07:06 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
1970-01-01 00:07:06 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
1970-01-01 00:07:06 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
1970-01-01 00:07:06 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
1970-01-01 00:07:18 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
1970-01-01 00:07:28 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
1970-01-01 00:07:38 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
1970-01-01 00:07:41 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
1970-01-01 00:07:41 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
1970-01-01 00:07:42 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
1970-01-01 00:07:42 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
1970-01-01 00:07:42 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
1970-01-01 00:07:42 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
1970-01-01 00:07:42 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
1970-01-01 00:07:42 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
1970-01-01 00:07:42 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
1970-01-01 00:07:42 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
1970-01-01 00:07:42 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
1970-01-01 00:07:42 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
1970-01-01 00:07:43 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
1970-01-01 00:07:43 voltage[0] = 1710
1970-01-01 00:07:43 voltage[1] = 1710
1970-01-01 00:07:43 voltage[2] = 1710
1970-01-01 00:07:43 power_api.c:140:set_working_voltage: working_voltage = 17.100000
1970-01-01 00:07:44 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
1970-01-01 00:07:45 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
1970-01-01 00:07:47 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
1970-01-01 00:07:47 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
1970-01-01 00:07:47 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
1970-01-01 00:07:47 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
1970-01-01 00:07:47 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
1970-01-01 00:07:49 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 17
1970-01-01 00:07:49 thread.c:804:create_check_miner_status_thread: create thread
1970-01-01 00:07:49 thread.c:794:create_set_miner_status_thread: create thread
1970-01-01 00:07:49 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
1970-01-01 00:07:49 thread.c:779:create_temperature_monitor_thread: create thread
1970-01-01 00:07:49 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
1970-01-01 00:07:49 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
1970-01-01 00:08:21 power_api.c:124:check_voltage_multi: retry time: 0
1970-01-01 00:08:23 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.124219 
1970-01-01 00:08:24 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.118095 
1970-01-01 00:08:26 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.246679 
1970-01-01 00:08:26 power_api.c:97:get_average_voltage: aveage voltage is: 18.162998 
1970-01-01 00:08:26 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
1970-01-01 00:08:26 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
1970-01-01 00:08:26 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
1970-01-01 00:08:27 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
1970-01-01 00:08:28 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
1970-01-01 00:08:28 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
1970-01-01 00:08:28 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
1970-01-01 00:08:28 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
1970-01-01 00:08:28 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
1970-01-01 00:08:28 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
1970-01-01 00:08:28 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
1970-01-01 00:08:28 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
1970-01-01 00:08:28 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
1970-01-01 00:08:29 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
1970-01-01 00:08:30 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
1970-01-01 00:08:30 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
1970-01-01 00:08:30 power_api.c:146:set_higher_voltage: higher_voltage = 18.000000
1970-01-01 00:08:30 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 18.00 ...
1970-01-01 00:08:54 power_api.c:124:check_voltage_multi: retry time: 0
1970-01-01 00:08:56 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.111972 
1970-01-01 00:08:58 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.093603 
1970-01-01 00:08:59 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.203818 
1970-01-01 00:08:59 power_api.c:97:get_average_voltage: aveage voltage is: 18.136465 
1970-01-01 00:08:59 frequency.c:540:get_current_min_freq: current min freq 670
1970-01-01 00:08:59 driver-btm-api.c:1660:check_clock_counter: freq 670 clock_counter_limit 85
1970-01-01 00:09:00 thread.c:478:clear_zero_nonce_mark: 0 nonce protect succeed.
1970-01-01 00:09:00 thread.c:799:create_check_system_status_thread: create thread
1970-01-01 00:09:01 driver-btm-api.c:2113:bitmain_soc_init: Init done!
1970-01-01 00:09:01 driver-btm-api.c:201:set_miner_status: STATUS_INIT
1970-01-01 00:09:06 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
1970-01-01 00:09:11 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
1970-01-01 00:09:15 thread.c:382:check_working_voltage: current PCB min temperature is 40
1970-01-01 00:09:15 thread.c:383:check_working_voltage: current voltage is 18.00V, recovery to 17.10V
1970-01-01 00:09:15 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.10 ...
1970-01-01 00:09:53 power_api.c:124:check_voltage_multi: retry time: 0
1970-01-01 00:09:55 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.169023 
1970-01-01 00:09:56 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.162900 
1970-01-01 00:09:58 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.273115 
1970-01-01 00:09:58 power_api.c:97:get_average_voltage: aveage voltage is: 17.201679 
1970-01-01 00:14:57 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 17980
1970-01-01 00:14:57 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 16935
1970-01-01 00:14:57 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 14659
1970-01-01 00:18:01 driver-btm-api.c:1293:dhash_chip_send_job: Version num 1
1970-01-01 00:18:09 driver-btm-api.c:201:set_miner_status: WARN_NET_LOST
1970-01-01 00:18:21 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
1970-01-01 00:18:22 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-05-01 04:33:01 driver-btm-api.c:201:set_miner_status: WARN_NET_LOST
2020-05-01 04:33:10 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-05-01 04:33:19 log.c:100:_log_update_name: _log_update_name
2020-05-01 04:33:19 log.c:100:_log_update_name: _log_update_name
2020-05-01 04:52:37 thread.c:204:calc_hashrate_avg: avg rate is 0.05 in 26471803 mins
2020-05-01 04:52:37 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 62~80
2020-05-01 04:52:37 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-01 04:52:37 thread.c:286:check_hashrate: current PCB min temperature 42
2020-05-01 04:52:37 thread.c:287:check_hashrate: current voltage is 17.10V, working voltage is 17.10V
2020-05-01 04:52:37 thread.c:318:check_hashrate: high temp, increase voltage 0.1V/0.2V to 17.20V
2020-05-01 04:52:37 driver-btm-api.c:2124:bitmain_reopen_core: reopen_core start!
2020-05-01 04:52:43 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-05-01 04:52:43 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-05-01 04:52:43 chain = 0, mode = 0, load_done = false.
2020-05-01 04:52:43 chain = 1, mode = 0, load_done = false.
2020-05-01 04:52:43 chain = 2, mode = 0, load_done = false.
2020-05-01 04:52:44 chain = 0, mode = 0, load_done = false.
2020-05-01 04:52:44 chain = 1, mode = 0, load_done = false.
2020-05-01 04:52:44 chain = 2, mode = 0, load_done = false.
2020-05-01 04:52:45 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-01 04:52:45 chain = 0, mode = 0, load_done = false.
2020-05-01 04:52:45 chain = 1, mode = 0, load_done = false.
2020-05-01 04:52:45 chain = 2, mode = 0, load_done = false.
2020-05-01 04:52:46 chain = 0, mode = 0, load_done = false.
2020-05-01 04:52:46 chain = 1, mode = 0, load_done = false.
2020-05-01 04:52:46 chain = 2, mode = 0, load_done = false.
2020-05-01 04:52:47 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-01 04:52:47 chain = 0, mode = 0, load_done = false.
2020-05-01 04:52:47 chain = 1, mode = 0, load_done = false.
2020-05-01 04:52:47 chain = 2, mode = 0, load_done = false.
2020-05-01 04:52:48 chain = 0, mode = 0, load_done = false.
2020-05-01 04:52:48 chain = 1, mode = 0, load_done = false.
2020-05-01 04:52:48 chain = 2, mode = 0, load_done = false.
2020-05-01 04:52:48 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-01 04:52:48 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-05-01 04:52:48 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-05-01 04:52:48 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-05-01 04:52:48 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-05-01 04:52:48 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-05-01 04:52:48 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-05-01 04:52:48 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-05-01 04:52:48 driver-btm-api.c:644:_set_project_type: project:2
2020-05-01 04:52:48 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-05-01 04:52:48 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-05-01 04:52:48 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-05-01 04:52:48 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-05-01 04:52:48 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-05-01 04:52:48 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-05-01 04:52:48 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-05-01 04:52:50 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-05-01 04:52:52 register.c:283:get_register: !!! reg crc error
2020-05-01 04:52:54 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-05-01 04:52:57 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-05-01 04:52:59 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-05-01 04:53:02 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-05-01 04:53:06 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-05-01 04:53:12 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-05-01 04:53:12 power_api.c:55:power_init: power init ... 
2020-05-01 04:53:12 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-05-01 04:53:44 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-05-01 04:53:45 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-01 04:53:47 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.218008 
2020-05-01 04:53:49 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.095547 
2020-05-01 04:53:51 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.242500 
2020-05-01 04:53:51 power_api.c:97:get_average_voltage: aveage voltage is: 17.185351 
2020-05-01 04:53:51 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-05-01 04:53:51 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-01 04:53:51 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-01 04:53:51 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-01 04:53:51 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-01 04:54:01 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-05-01 04:54:11 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-05-01 04:54:21 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-05-01 04:54:24 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-05-01 04:54:25 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-05-01 04:54:25 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-05-01 04:54:25 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-05-01 04:54:25 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-05-01 04:54:25 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-05-01 04:54:25 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-05-01 04:54:25 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-05-01 04:54:25 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-05-01 04:54:26 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-01 04:54:26 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-01 04:54:26 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-01 04:54:26 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-01 04:54:26 voltage[0] = 1710
2020-05-01 04:54:26 voltage[1] = 1710
2020-05-01 04:54:26 voltage[2] = 1710
2020-05-01 04:54:26 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-05-01 04:54:27 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-05-01 04:54:29 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-05-01 04:54:30 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-05-01 04:54:30 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-05-01 04:54:30 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-05-01 04:54:30 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-05-01 04:54:30 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-05-01 04:54:32 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 19
2020-05-01 04:54:32 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-05-01 04:54:32 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-05-01 04:55:04 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-01 04:55:06 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.136465 
2020-05-01 04:55:08 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.118095 
2020-05-01 04:55:09 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.240556 
2020-05-01 04:55:09 power_api.c:97:get_average_voltage: aveage voltage is: 18.165039 
2020-05-01 04:55:09 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-01 04:55:10 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-01 04:55:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-01 04:55:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-01 04:55:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-01 04:55:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-01 04:55:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-01 04:55:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-01 04:55:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-01 04:55:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-01 04:55:11 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-01 04:55:12 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-01 04:55:13 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-01 04:55:13 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-01 04:55:13 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-01 04:55:13 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-05-01 04:55:13 power_api.c:146:set_higher_voltage: higher_voltage = 18.000000
2020-05-01 04:55:13 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 18.00 ...
2020-05-01 04:55:35 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-01 04:55:37 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.105849 
2020-05-01 04:55:38 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.099726 
2020-05-01 04:55:40 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.203818 
2020-05-01 04:55:40 power_api.c:97:get_average_voltage: aveage voltage is: 18.136465 
2020-05-01 04:55:41 driver-btm-api.c:2186:bitmain_reopen_core: reopen_core done!
2020-05-01 04:55:41 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.20 ...
2020-05-01 04:56:21 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-01 04:56:23 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.279238 
2020-05-01 04:56:25 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.266992 
2020-05-01 04:56:26 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.371084 
2020-05-01 04:56:26 power_api.c:97:get_average_voltage: aveage voltage is: 17.305771 
2020-05-01 04:56:26 power_api.c:140:set_working_voltage: working_voltage = 17.200001
2020-05-01 05:01:25 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 112684
2020-05-01 05:01:25 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 107768
2020-05-01 05:01:25 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 92532
2020-05-01 05:26:26 thread.c:204:calc_hashrate_avg: avg rate is 39234.15 in 30 mins
2020-05-01 05:26:26 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 63~80
2020-05-01 05:56:28 thread.c:204:calc_hashrate_avg: avg rate is 39273.71 in 30 mins
2020-05-01 05:56:28 temperature.c:450:temp_statistics_show:   pcb temp 42~57  chip temp 63~80
2020-05-01 06:26:29 thread.c:204:calc_hashrate_avg: avg rate is 38989.37 in 30 mins
2020-05-01 06:26:29 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 64~80
2020-05-01 06:26:29 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-01 06:26:29 thread.c:286:check_hashrate: current PCB min temperature 42
2020-05-01 06:26:29 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-01 06:26:29 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-01 06:56:30 thread.c:204:calc_hashrate_avg: avg rate is 39031.50 in 30 mins
2020-05-01 06:56:30 temperature.c:450:temp_statistics_show:   pcb temp 42~57  chip temp 63~80

[...]

2020-05-02 04:27:26 thread.c:204:calc_hashrate_avg: avg rate is 39244.02 in 30 mins
2020-05-02 04:27:26 temperature.c:450:temp_statistics_show:   pcb temp 38~56  chip temp 59~80
2020-05-02 04:57:27 thread.c:204:calc_hashrate_avg: avg rate is 39168.48 in 30 mins
2020-05-02 04:57:27 temperature.c:450:temp_statistics_show:   pcb temp 41~56  chip temp 62~80
2020-05-02 04:57:27 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-02 04:57:27 thread.c:286:check_hashrate: current PCB min temperature 41
2020-05-02 04:57:27 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-02 04:57:27 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-02 05:27:28 thread.c:204:calc_hashrate_avg: avg rate is 39010.16 in 30 mins
2020-05-02 05:27:28 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 63~80
2020-05-02 05:27:28 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-02 05:27:28 thread.c:286:check_hashrate: current PCB min temperature 42
2020-05-02 05:27:28 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-02 05:27:28 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V

Miner Status Screen:

https://drive.google.com/file/d/197SGfVUR8r7rLnQQDiwElOplCgagpMZC/view?usp=sharing

[mysticbitcoin]

DOWNHILL:

Kernel Log - After reboot (many be a few):

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203756K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25620K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12580K (cceb8000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 4244297529
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 01559AD8-7B6A-42E6-A3FE-EDF3659527A9, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1052/339, WL threshold: 4096, image sequence number: 4185749592
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 4829CF2C-7435-4146-B2FD-0826AAE8443A, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2020-05-03 00:44:13 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2020-05-03 00:44:13 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2020-05-03 00:44:13 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2020-05-03 00:44:13 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-05-03 00:44:13 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2020-05-03 00:44:13 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2020-05-03 00:44:13 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2020-05-03 00:44:13 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2020-05-03 00:44:13 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-05-03 00:44:13 thread.c:789:create_read_nonce_reg_thread: create thread
2020-05-03 00:44:19 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-05-03 00:44:19 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-05-03 00:44:21 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 00:44:23 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 00:44:25 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 00:44:25 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-05-03 00:44:25 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-05-03 00:44:25 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-05-03 00:44:25 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-05-03 00:44:25 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-05-03 00:44:25 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-05-03 00:44:25 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-05-03 00:44:25 driver-btm-api.c:644:_set_project_type: project:2
2020-05-03 00:44:25 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-05-03 00:44:25 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-05-03 00:44:25 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-05-03 00:44:25 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-05-03 00:44:25 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-05-03 00:44:25 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-05-03 00:44:25 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-05-03 00:44:27 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-05-03 00:44:28 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-05-03 00:44:32 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-05-03 00:44:34 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-05-03 00:44:37 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-05-03 00:44:39 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-05-03 00:44:42 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-05-03 00:44:42 thread.c:784:create_pic_heart_beat_thread: create thread
2020-05-03 00:44:42 power_api.c:55:power_init: power init ... 
2020-05-03 00:44:42 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-05-03 00:45:14 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-05-03 00:45:20 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 00:45:22 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.113916 
2020-05-03 00:45:24 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.113916 
2020-05-03 00:45:25 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.224131 
2020-05-03 00:45:25 power_api.c:97:get_average_voltage: aveage voltage is: 17.150654 
2020-05-03 00:45:25 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-05-03 00:45:25 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-03 00:45:25 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-03 00:45:25 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-03 00:45:26 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-03 00:45:37 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-05-03 00:45:47 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-05-03 00:45:57 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-05-03 00:46:01 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 00:46:01 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 00:46:01 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 00:46:01 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-05-03 00:46:01 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-05-03 00:46:01 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-05-03 00:46:01 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-05-03 00:46:01 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-05-03 00:46:01 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-05-03 00:46:02 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-03 00:46:02 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-03 00:46:02 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-03 00:46:02 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-03 00:46:02 voltage[0] = 1710
2020-05-03 00:46:02 voltage[1] = 1710
2020-05-03 00:46:02 voltage[2] = 1710
2020-05-03 00:46:02 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-05-03 00:46:03 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-05-03 00:46:05 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-05-03 00:46:06 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-05-03 00:46:06 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-05-03 00:46:06 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-05-03 00:46:06 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-05-03 00:46:06 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-05-03 00:46:08 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 24
2020-05-03 00:46:08 thread.c:804:create_check_miner_status_thread: create thread
2020-05-03 00:46:08 thread.c:794:create_set_miner_status_thread: create thread
2020-05-03 00:46:08 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-05-03 00:46:08 thread.c:779:create_temperature_monitor_thread: create thread
2020-05-03 00:46:08 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2020-05-03 00:46:08 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-05-03 00:46:40 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 00:46:42 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.130342 
2020-05-03 00:46:44 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.111972 
2020-05-03 00:46:45 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.228310 
2020-05-03 00:46:45 power_api.c:97:get_average_voltage: aveage voltage is: 18.156875 
2020-05-03 00:46:45 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 00:46:46 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 00:46:46 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 00:46:46 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 00:46:46 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 00:46:46 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 00:46:46 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 00:46:46 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 00:46:46 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 00:46:46 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 00:46:47 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 00:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 00:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 00:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 00:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 00:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 00:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 00:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 00:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 00:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 00:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 00:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 00:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 00:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 00:46:49 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-05-03 00:46:49 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.10 ...
2020-05-03 00:47:26 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 00:47:28 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.199638 
2020-05-03 00:47:30 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.175146 
2020-05-03 00:47:31 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.297607 
2020-05-03 00:47:31 power_api.c:97:get_average_voltage: aveage voltage is: 17.224131 
2020-05-03 00:47:31 frequency.c:540:get_current_min_freq: current min freq 670
2020-05-03 00:47:31 driver-btm-api.c:1660:check_clock_counter: freq 670 clock_counter_limit 85
2020-05-03 00:47:33 thread.c:799:create_check_system_status_thread: create thread
2020-05-03 00:47:33 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2020-05-03 00:47:33 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2020-05-03 00:47:38 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-05-03 00:48:14 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
2020-05-03 00:53:13 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 15397
2020-05-03 00:53:13 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 14678
2020-05-03 00:53:13 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 12461
2020-05-03 01:18:14 thread.c:204:calc_hashrate_avg: avg rate is 39088.74 in 30 mins
2020-05-03 01:18:14 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 64~80
2020-05-03 01:18:14 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 01:18:14 thread.c:286:check_hashrate: current PCB min temperature 42
2020-05-03 01:18:14 thread.c:287:check_hashrate: current voltage is 17.10V, working voltage is 17.10V
2020-05-03 01:18:14 thread.c:318:check_hashrate: high temp, increase voltage 0.1V/0.2V to 17.20V
2020-05-03 01:18:14 driver-btm-api.c:2124:bitmain_reopen_core: reopen_core start!
2020-05-03 01:18:20 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-05-03 01:18:20 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-05-03 01:18:21 chain = 0, mode = 0, load_done = false.
2020-05-03 01:18:21 chain = 1, mode = 0, load_done = false.
2020-05-03 01:18:21 chain = 2, mode = 0, load_done = false.
2020-05-03 01:18:22 chain = 0, mode = 0, load_done = false.
2020-05-03 01:18:22 chain = 1, mode = 0, load_done = false.
2020-05-03 01:18:22 chain = 2, mode = 0, load_done = false.
2020-05-03 01:18:22 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 01:18:23 chain = 0, mode = 0, load_done = false.
2020-05-03 01:18:23 chain = 1, mode = 0, load_done = false.
2020-05-03 01:18:23 chain = 2, mode = 0, load_done = false.
2020-05-03 01:18:24 chain = 0, mode = 0, load_done = false.
2020-05-03 01:18:24 chain = 1, mode = 0, load_done = false.
2020-05-03 01:18:24 chain = 2, mode = 0, load_done = false.
2020-05-03 01:18:24 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 01:18:25 chain = 0, mode = 0, load_done = false.
2020-05-03 01:18:25 chain = 1, mode = 0, load_done = false.
2020-05-03 01:18:25 chain = 2, mode = 0, load_done = false.
2020-05-03 01:18:26 chain = 0, mode = 0, load_done = false.
2020-05-03 01:18:26 chain = 1, mode = 0, load_done = false.
2020-05-03 01:18:26 chain = 2, mode = 0, load_done = false.
2020-05-03 01:18:26 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 01:18:26 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-05-03 01:18:26 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-05-03 01:18:26 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-05-03 01:18:26 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-05-03 01:18:26 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-05-03 01:18:26 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-05-03 01:18:26 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-05-03 01:18:26 driver-btm-api.c:644:_set_project_type: project:2
2020-05-03 01:18:26 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-05-03 01:18:26 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-05-03 01:18:26 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-05-03 01:18:26 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-05-03 01:18:26 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-05-03 01:18:26 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-05-03 01:18:26 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-05-03 01:18:28 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-05-03 01:18:28 register.c:283:get_register: !!! reg crc error
2020-05-03 01:18:30 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-05-03 01:18:36 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-05-03 01:18:38 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-05-03 01:18:41 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-05-03 01:18:43 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-05-03 01:18:48 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-05-03 01:18:48 power_api.c:55:power_init: power init ... 
2020-05-03 01:18:48 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-05-03 01:19:20 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-05-03 01:19:24 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 01:19:25 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.120039 
2020-05-03 01:19:27 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.113916 
2020-05-03 01:19:29 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.224131 
2020-05-03 01:19:29 power_api.c:97:get_average_voltage: aveage voltage is: 17.152695 
2020-05-03 01:19:29 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-05-03 01:19:29 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-03 01:19:29 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-03 01:19:29 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-03 01:19:29 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-03 01:19:40 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-05-03 01:19:50 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-05-03 01:20:01 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 23 asic, times 0
2020-05-03 01:20:11 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 23 asic, times 1
2020-05-03 01:20:20 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 23 asic, times 2
2020-05-03 01:20:20 driver-btm-api.c:1037:check_asic_number: Chain 2 only find 23 asic, will power off hash board 2
2020-05-03 01:20:26 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 01:20:26 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 01:20:26 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-05-03 01:20:27 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-05-03 01:20:27 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-05-03 01:20:27 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-05-03 01:20:27 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-05-03 01:20:27 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-03 01:20:27 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-03 01:20:27 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-03 01:20:27 voltage[0] = 1710
2020-05-03 01:20:27 voltage[1] = 1710
2020-05-03 01:20:27 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-05-03 01:20:28 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-05-03 01:20:30 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-05-03 01:20:30 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-05-03 01:20:30 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-05-03 01:20:30 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-05-03 01:20:31 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 20
2020-05-03 01:20:31 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-05-03 01:20:31 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-05-03 01:21:00 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 01:21:02 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.160957 
2020-05-03 01:21:03 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.148711 
2020-05-03 01:21:03 power_api.c:97:get_average_voltage: aveage voltage is: 18.154834 
2020-05-03 01:21:03 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 01:21:04 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 01:21:04 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 01:21:04 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 01:21:04 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 01:21:04 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 01:21:04 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 01:21:04 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 01:21:04 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 01:21:04 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 01:21:05 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 01:21:06 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 01:21:06 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 01:21:06 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-05-03 01:21:06 power_api.c:146:set_higher_voltage: higher_voltage = 18.000000
2020-05-03 01:21:06 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 18.00 ...
2020-05-03 01:21:25 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 01:21:27 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.142588 
2020-05-03 01:21:29 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.124219 
2020-05-03 01:21:29 power_api.c:97:get_average_voltage: aveage voltage is: 18.133403 
2020-05-03 01:21:29 driver-btm-api.c:2186:bitmain_reopen_core: reopen_core done!
2020-05-03 01:21:29 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.20 ...
2020-05-03 01:22:04 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 01:22:06 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.297607 
2020-05-03 01:22:08 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.279238 
2020-05-03 01:22:08 power_api.c:97:get_average_voltage: aveage voltage is: 17.288423 
2020-05-03 01:22:08 power_api.c:140:set_working_voltage: working_voltage = 17.200001
2020-05-03 01:27:07 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 109508
2020-05-03 01:27:07 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 104312
2020-05-03 01:52:08 thread.c:204:calc_hashrate_avg: avg rate is 27576.08 in 30 mins
2020-05-03 01:52:08 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 65~80
2020-05-03 02:22:09 thread.c:204:calc_hashrate_avg: avg rate is 27625.39 in 30 mins
2020-05-03 02:22:09 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 64~79

Miner Status Screen: https://drive.google.com/file/d/1W87ewVEAnAqcX6uh8zDsLQMMoYNa7jg-/view?usp=sharing

Things to Note: (Its rebooted a few times - this is what I could get for the kernel log)

Code:

2020-05-03 01:20:01 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 23 asic, times 0
2020-05-03 01:20:11 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 23 asic, times 1
2020-05-03 01:20:20 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 23 asic, times 2
2020-05-03 01:20:20 driver-btm-api.c:1037:check_asic_number: Chain 2 only find 23 asic, will power off hash board 2

[mikeywith]

Code:

2020-05-03 01:52:08 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 65~80
2020-05-03 02:22:09 thread.c:204:calc_hashrate_avg: avg rate is 27625.39 in 30 mins
2020-05-03 02:22:09 temperature.c:450:temp_statistics_show:   pcb temp 42~56  chip temp 64~79

Your temps are pretty high, chain 2 does show less ASICs than it should but that's not your only issue, your temps are pretty high forcing the miner to lower the voltage/frequency which may cause it to be unstable and then reboot/stop mining. When you remove the third board (Chain 2) the other two boards will cool down and there is a good chance they will mine on without an issue and you will think that chain 2 was the only problem when actually you have a heat problem.

I suggest you set the fans at 100% and see if the miner works more stable with these settings if you don't know how to set a fixed speed for those fans let me know I'll show you.

[mysticbitcoin]

Mikey, This is the only one of the T17s giving me grief. The ambient environment temp being an average of 22 degrees Celsius to a maximum of 24 degrees Celsius. The highest the boards get according to the logs is 45 Degrees, which is within operating spec according to Bitmain. But I agree with what your saying according to the logs. The funny thing is I was so fustrated I opened her up and re-seated the Chain [2] Cable (take it out and plug it in on the Hashboard side) and she came up online all 30 chips recognized. Could the cable be a problem? Ive never heard of such a case but Bitmain always gives a default trouble shooting of replacing the controller to hashboard cables (although I've never found that they have been particularly helpful).

Here is the most Kernel recent log, running all night since I re-seated the cable.

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203756K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25620K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12580K (cceb8000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/2, WL threshold: 4096, image sequence number: 4244297529
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 01559AD8-7B6A-42E6-A3FE-EDF3659527A9, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1052/340, WL threshold: 4096, image sequence number: 4185749592
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 4829CF2C-7435-4146-B2FD-0826AAE8443A, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2020-05-03 04:09:50 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2020-05-03 04:09:50 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2020-05-03 04:09:50 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2020-05-03 04:09:50 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-05-03 04:09:50 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2020-05-03 04:09:50 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2020-05-03 04:09:50 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2020-05-03 04:09:50 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2020-05-03 04:09:50 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-05-03 04:09:50 thread.c:789:create_read_nonce_reg_thread: create thread
2020-05-03 04:09:56 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-05-03 04:09:56 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-05-03 04:09:58 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 04:10:00 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 04:10:02 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 04:10:02 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-05-03 04:10:02 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-05-03 04:10:02 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-05-03 04:10:02 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-05-03 04:10:02 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-05-03 04:10:02 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-05-03 04:10:02 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-05-03 04:10:02 driver-btm-api.c:644:_set_project_type: project:2
2020-05-03 04:10:02 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-05-03 04:10:02 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-05-03 04:10:02 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-05-03 04:10:02 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-05-03 04:10:02 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-05-03 04:10:02 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-05-03 04:10:02 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-05-03 04:10:04 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-05-03 04:10:05 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-05-03 04:10:09 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-05-03 04:10:11 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-05-03 04:10:14 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-05-03 04:10:16 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-05-03 04:10:19 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-05-03 04:10:19 thread.c:784:create_pic_heart_beat_thread: create thread
2020-05-03 04:10:19 power_api.c:55:power_init: power init ... 
2020-05-03 04:10:19 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-05-03 04:10:19 power_api.c:46:power_off: init gpio907
2020-05-03 04:10:51 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-05-03 04:10:57 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 04:10:59 power_api.c:86:get_average_voltage: chain[0], voltage is: 21.253095 
2020-05-03 04:11:01 power_api.c:86:get_average_voltage: chain[1], voltage is: 20.573437 
2020-05-03 04:11:02 power_api.c:86:get_average_voltage: chain[2], voltage is: 20.071347 
2020-05-03 04:11:02 power_api.c:97:get_average_voltage: aveage voltage is: 20.632627 
2020-05-03 04:11:02 power_api.c:110:check_voltage: target_vol = 17.00, actural_vol = 20.63, more than 1.0v diff.
2020-05-03 04:11:03 power_api.c:124:check_voltage_multi: retry time: 1
2020-05-03 04:11:05 power_api.c:86:get_average_voltage: chain[0], voltage is: 19.048799 
2020-05-03 04:11:07 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.454863 
2020-05-03 04:11:10 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.622129 
2020-05-03 04:11:10 power_api.c:97:get_average_voltage: aveage voltage is: 18.375263 
2020-05-03 04:11:10 power_api.c:110:check_voltage: target_vol = 17.00, actural_vol = 18.38, more than 1.0v diff.
2020-05-03 04:11:11 power_api.c:124:check_voltage_multi: retry time: 2
2020-05-03 04:11:13 power_api.c:86:get_average_voltage: chain[0], voltage is: 16.599580 
2020-05-03 04:11:16 power_api.c:86:get_average_voltage: chain[1], voltage is: 15.748476 
2020-05-03 04:11:18 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.456806 
2020-05-03 04:11:18 power_api.c:97:get_average_voltage: aveage voltage is: 16.601621 
2020-05-03 04:11:18 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-05-03 04:11:18 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-03 04:11:18 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-03 04:11:18 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-03 04:11:18 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-03 04:11:28 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-05-03 04:11:38 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-05-03 04:11:49 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-05-03 04:11:52 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 04:11:52 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 04:11:52 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 04:11:53 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-05-03 04:11:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-05-03 04:11:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-05-03 04:11:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-05-03 04:11:53 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-05-03 04:11:53 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-05-03 04:11:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-03 04:11:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-03 04:11:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-03 04:11:53 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-03 04:11:53 voltage[0] = 1710
2020-05-03 04:11:53 voltage[1] = 1710
2020-05-03 04:11:53 voltage[2] = 1710
2020-05-03 04:11:53 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-05-03 04:11:55 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-05-03 04:11:56 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-05-03 04:11:57 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-05-03 04:11:57 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-05-03 04:11:57 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-05-03 04:11:57 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-05-03 04:11:57 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-05-03 04:11:59 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 20
2020-05-03 04:11:59 thread.c:804:create_check_miner_status_thread: create thread
2020-05-03 04:11:59 thread.c:794:create_set_miner_status_thread: create thread
2020-05-03 04:11:59 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-05-03 04:11:59 thread.c:779:create_temperature_monitor_thread: create thread
2020-05-03 04:11:59 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2020-05-03 04:11:59 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-05-03 04:12:35 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 04:12:37 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.142588 
2020-05-03 04:12:39 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.124219 
2020-05-03 04:12:40 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.240556 
2020-05-03 04:12:40 power_api.c:97:get_average_voltage: aveage voltage is: 18.169121 
2020-05-03 04:12:40 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 04:12:41 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 04:12:42 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 04:12:42 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 04:12:42 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 04:12:42 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 04:12:42 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 04:12:42 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 04:12:42 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 04:12:42 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 04:12:42 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 04:12:43 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 04:12:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 04:12:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 04:12:44 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 04:12:44 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-05-03 04:12:44 power_api.c:146:set_higher_voltage: higher_voltage = 18.000000
2020-05-03 04:12:44 power_api.c:428:slowly_set_iic_power_to_higher_voltage: slowly setting to voltage: 18.00 ...
2020-05-03 04:13:08 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 04:13:10 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.118095 
2020-05-03 04:13:12 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.081357 
2020-05-03 04:13:14 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.197695 
2020-05-03 04:13:14 power_api.c:97:get_average_voltage: aveage voltage is: 18.132383 
2020-05-03 04:13:14 frequency.c:540:get_current_min_freq: current min freq 670
2020-05-03 04:13:14 driver-btm-api.c:1660:check_clock_counter: freq 670 clock_counter_limit 85
2020-05-03 04:13:14 thread.c:799:create_check_system_status_thread: create thread
2020-05-03 04:13:15 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2020-05-03 04:13:15 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2020-05-03 04:13:19 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-05-03 04:13:24 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
2020-05-03 04:13:28 thread.c:382:check_working_voltage: current PCB min temperature is 43
2020-05-03 04:13:28 thread.c:383:check_working_voltage: current voltage is 18.00V, recovery to 17.10V
2020-05-03 04:13:28 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.10 ...
2020-05-03 04:14:00 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 04:14:04 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.187392 
2020-05-03 04:14:07 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.162900 
2020-05-03 04:14:10 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.285361 
2020-05-03 04:14:10 power_api.c:97:get_average_voltage: aveage voltage is: 17.211885 
2020-05-03 04:19:09 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 17787
2020-05-03 04:19:09 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 16839
2020-05-03 04:19:09 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 14466
2020-05-03 04:43:05 driver-btm-api.c:201:set_miner_status: WARN_NET_LOST
2020-05-03 04:44:11 thread.c:204:calc_hashrate_avg: avg rate is 38861.96 in 30 mins
2020-05-03 04:44:11 temperature.c:450:temp_statistics_show:   pcb temp 43~56  chip temp 64~80
2020-05-03 04:44:11 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 04:44:11 thread.c:286:check_hashrate: current PCB min temperature 43
2020-05-03 04:44:11 thread.c:287:check_hashrate: current voltage is 17.10V, working voltage is 17.10V
2020-05-03 04:44:11 thread.c:318:check_hashrate: high temp, increase voltage 0.1V/0.2V to 17.20V
2020-05-03 04:44:11 driver-btm-api.c:2124:bitmain_reopen_core: reopen_core start!
2020-05-03 04:44:17 driver-btm-api.c:1067:init_miner_version: miner ID : 8042750618c0885c
2020-05-03 04:44:17 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2020-05-03 04:44:18 chain = 0, mode = 0, load_done = false.
2020-05-03 04:44:18 chain = 1, mode = 0, load_done = false.
2020-05-03 04:44:18 chain = 2, mode = 0, load_done = false.
2020-05-03 04:44:19 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 04:44:19 chain = 0, mode = 0, load_done = false.
2020-05-03 04:44:19 chain = 1, mode = 0, load_done = false.
2020-05-03 04:44:19 chain = 2, mode = 0, load_done = false.
2020-05-03 04:44:20 chain = 0, mode = 0, load_done = false.
2020-05-03 04:44:20 chain = 1, mode = 0, load_done = false.
2020-05-03 04:44:20 chain = 2, mode = 0, load_done = false.
2020-05-03 04:44:21 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 04:44:21 chain = 0, mode = 0, load_done = false.
2020-05-03 04:44:21 chain = 1, mode = 0, load_done = false.
2020-05-03 04:44:21 chain = 2, mode = 0, load_done = false.
2020-05-03 04:44:22 chain = 0, mode = 0, load_done = false.
2020-05-03 04:44:22 chain = 1, mode = 0, load_done = false.
2020-05-03 04:44:22 chain = 2, mode = 0, load_done = false.
2020-05-03 04:44:23 eeprom.c:425:check_pattern_test_level: invalid pattern test result. ignore
2020-05-03 04:44:23 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2020-05-03 04:44:23 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2020-05-03 04:44:23 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2020-05-03 04:44:23 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2020-05-03 04:44:23 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2020-05-03 04:44:23 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2020-05-03 04:44:23 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2020-05-03 04:44:23 driver-btm-api.c:644:_set_project_type: project:2
2020-05-03 04:44:23 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2020-05-03 04:44:23 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2020-05-03 04:44:23 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-05-03 04:44:23 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2020-05-03 04:44:23 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-05-03 04:44:23 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2020-05-03 04:44:23 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-05-03 04:44:25 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2020-05-03 04:44:25 register.c:283:get_register: !!! reg crc error
2020-05-03 04:44:27 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-05-03 04:44:33 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-05-03 04:44:36 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-05-03 04:44:41 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-05-03 04:44:43 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-05-03 04:44:46 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-05-03 04:44:46 power_api.c:55:power_init: power init ... 
2020-05-03 04:44:46 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-05-03 04:45:18 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2020-05-03 04:45:20 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 04:45:22 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.230254 
2020-05-03 04:45:25 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.126162 
2020-05-03 04:45:28 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.211885 
2020-05-03 04:45:28 power_api.c:97:get_average_voltage: aveage voltage is: 17.189433 
2020-05-03 04:45:28 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2020-05-03 04:45:28 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-03 04:45:28 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-03 04:45:28 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-03 04:45:28 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-03 04:45:38 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2020-05-03 04:45:48 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2020-05-03 04:45:58 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2020-05-03 04:46:01 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 04:46:01 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 04:46:02 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2020-05-03 04:46:02 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2020-05-03 04:46:02 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-05-03 04:46:02 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-05-03 04:46:02 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-05-03 04:46:02 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2020-05-03 04:46:02 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2020-05-03 04:46:02 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-05-03 04:46:02 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-05-03 04:46:02 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-05-03 04:46:02 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2020-05-03 04:46:03 voltage[0] = 1710
2020-05-03 04:46:03 voltage[1] = 1710
2020-05-03 04:46:03 voltage[2] = 1710
2020-05-03 04:46:03 power_api.c:140:set_working_voltage: working_voltage = 17.100000
2020-05-03 04:46:04 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-05-03 04:46:05 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-05-03 04:46:07 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-05-03 04:46:07 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-05-03 04:46:07 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-05-03 04:46:07 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-05-03 04:46:07 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2020-05-03 04:46:08 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 21
2020-05-03 04:46:08 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2020-05-03 04:46:08 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2020-05-03 04:46:41 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 04:46:43 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.142588 
2020-05-03 04:46:44 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.130342 
2020-05-03 04:46:48 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.258926 
2020-05-03 04:46:48 power_api.c:97:get_average_voltage: aveage voltage is: 18.177285 
2020-05-03 04:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 42 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 04:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 50 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 04:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 60 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 04:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 75 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 04:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 100 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 04:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 150 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 04:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 300 set refdiv: 2, fbdiv: 168, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 04:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 350 set refdiv: 2, fbdiv: 168, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 04:46:48 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 420 set refdiv: 2, fbdiv: 168, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 525 set refdiv: 2, fbdiv: 168, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 700 set refdiv: 2, fbdiv: 168, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 04:46:49 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 41 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 7, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 47 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 6, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 57 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 5, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 71 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 4, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 95 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 3, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 143 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 2, usr divider: 1
2020-05-03 04:46:50 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 287 set refdiv: 2, fbdiv: 161, postdiv1: 7, postdiv2: 1, usr divider: 1
2020-05-03 04:46:51 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 335 set refdiv: 2, fbdiv: 161, postdiv1: 6, postdiv2: 1, usr divider: 1
2020-05-03 04:46:51 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 402 set refdiv: 2, fbdiv: 161, postdiv1: 5, postdiv2: 1, usr divider: 1
2020-05-03 04:46:51 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 503 set refdiv: 2, fbdiv: 161, postdiv1: 4, postdiv2: 1, usr divider: 1
2020-05-03 04:46:51 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 670 set refdiv: 2, fbdiv: 161, postdiv1: 3, postdiv2: 1, usr divider: 1
2020-05-03 04:46:51 driver-btm-api.c:612:set_timeout: freq 700 final timeout=168
2020-05-03 04:46:51 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.10 ...
2020-05-03 04:47:24 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 04:47:26 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.181269 
2020-05-03 04:47:28 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.156777 
2020-05-03 04:47:29 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.279238 
2020-05-03 04:47:29 power_api.c:97:get_average_voltage: aveage voltage is: 17.205762 
2020-05-03 04:47:29 driver-btm-api.c:1293:dhash_chip_send_job: Version num 1
2020-05-03 04:47:29 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
2020-05-03 04:47:30 driver-btm-api.c:2186:bitmain_reopen_core: reopen_core done!
2020-05-03 04:47:30 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.20 ...
2020-05-03 04:47:57 power_api.c:124:check_voltage_multi: retry time: 0
2020-05-03 04:47:59 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.279238 
2020-05-03 04:48:01 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.266992 
2020-05-03 04:48:03 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.377207 
2020-05-03 04:48:03 power_api.c:97:get_average_voltage: aveage voltage is: 17.307812 
2020-05-03 04:48:03 power_api.c:140:set_working_voltage: working_voltage = 17.200001
2020-05-03 04:49:02 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2020-05-03 04:53:02 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 111804
2020-05-03 04:53:02 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 106763
2020-05-03 04:53:02 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 91522
2020-05-03 05:18:02 thread.c:204:calc_hashrate_avg: avg rate is 39414.58 in 30 mins
2020-05-03 05:18:02 temperature.c:450:temp_statistics_show:   pcb temp 44~57  chip temp 65~80
2020-05-03 05:48:03 thread.c:204:calc_hashrate_avg: avg rate is 39042.75 in 30 mins
2020-05-03 05:48:03 temperature.c:450:temp_statistics_show:   pcb temp 44~57  chip temp 65~80
2020-05-03 05:48:03 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 05:48:03 thread.c:286:check_hashrate: current PCB min temperature 44
2020-05-03 05:48:03 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 05:48:03 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 06:18:04 thread.c:204:calc_hashrate_avg: avg rate is 39262.43 in 30 mins
2020-05-03 06:18:04 temperature.c:450:temp_statistics_show:   pcb temp 44~57  chip temp 65~80
2020-05-03 06:48:06 thread.c:204:calc_hashrate_avg: avg rate is 39010.80 in 30 mins
2020-05-03 06:48:06 temperature.c:450:temp_statistics_show:   pcb temp 44~57  chip temp 65~80
2020-05-03 06:48:06 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 06:48:06 thread.c:286:check_hashrate: current PCB min temperature 44
2020-05-03 06:48:06 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 06:48:06 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 07:18:07 thread.c:204:calc_hashrate_avg: avg rate is 39115.22 in 30 mins
2020-05-03 07:18:07 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~81
2020-05-03 07:18:07 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 07:18:07 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 07:18:07 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 07:18:07 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 07:48:08 thread.c:204:calc_hashrate_avg: avg rate is 39039.77 in 30 mins
2020-05-03 07:48:08 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 07:48:08 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 07:48:08 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 07:48:08 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 07:48:08 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 08:18:10 thread.c:204:calc_hashrate_avg: avg rate is 39204.20 in 30 mins
2020-05-03 08:18:10 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 08:48:11 thread.c:204:calc_hashrate_avg: avg rate is 39071.31 in 30 mins
2020-05-03 08:48:11 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 08:48:11 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 08:48:11 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 08:48:11 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 08:48:11 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 09:18:12 thread.c:204:calc_hashrate_avg: avg rate is 39131.81 in 30 mins
2020-05-03 09:18:12 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 09:18:12 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 09:18:12 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 09:18:12 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 09:18:12 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 09:48:14 thread.c:204:calc_hashrate_avg: avg rate is 39150.20 in 30 mins
2020-05-03 09:48:14 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 09:48:14 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 09:48:14 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 09:48:14 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 09:48:14 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 10:18:15 thread.c:204:calc_hashrate_avg: avg rate is 39184.80 in 30 mins
2020-05-03 10:18:15 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 10:18:15 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 10:18:15 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 10:18:15 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 10:18:15 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 10:48:16 thread.c:204:calc_hashrate_avg: avg rate is 38965.19 in 30 mins
2020-05-03 10:48:16 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 10:48:16 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 10:48:16 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 10:48:16 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 10:48:16 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 11:18:17 thread.c:204:calc_hashrate_avg: avg rate is 39314.97 in 30 mins
2020-05-03 11:18:17 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 11:48:19 thread.c:204:calc_hashrate_avg: avg rate is 39373.88 in 30 mins
2020-05-03 11:48:19 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 12:18:20 thread.c:204:calc_hashrate_avg: avg rate is 38999.76 in 30 mins
2020-05-03 12:18:20 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~81
2020-05-03 12:18:20 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 12:18:20 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 12:18:20 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 12:18:20 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 12:48:21 thread.c:204:calc_hashrate_avg: avg rate is 38962.77 in 30 mins
2020-05-03 12:48:21 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 12:48:21 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 12:48:21 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 12:48:21 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 12:48:21 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 13:18:22 thread.c:204:calc_hashrate_avg: avg rate is 39077.63 in 30 mins
2020-05-03 13:18:22 temperature.c:450:temp_statistics_show:   pcb temp 45~57  chip temp 66~80
2020-05-03 13:18:22 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 13:18:22 thread.c:286:check_hashrate: current PCB min temperature 45
2020-05-03 13:18:22 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 13:18:22 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 13:48:24 thread.c:204:calc_hashrate_avg: avg rate is 38996.33 in 30 mins
2020-05-03 13:48:24 temperature.c:450:temp_statistics_show:   pcb temp 38~56  chip temp 59~79
2020-05-03 13:48:24 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 13:48:24 thread.c:286:check_hashrate: current PCB min temperature 38
2020-05-03 13:48:24 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 13:48:24 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 14:18:25 thread.c:204:calc_hashrate_avg: avg rate is 39111.03 in 30 mins
2020-05-03 14:18:25 temperature.c:450:temp_statistics_show:   pcb temp 38~56  chip temp 59~80
2020-05-03 14:18:25 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 14:18:25 thread.c:286:check_hashrate: current PCB min temperature 38
2020-05-03 14:18:25 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 14:18:25 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V
2020-05-03 14:48:26 thread.c:204:calc_hashrate_avg: avg rate is 38897.26 in 30 mins
2020-05-03 14:48:26 temperature.c:450:temp_statistics_show:   pcb temp 37~55  chip temp 58~79
2020-05-03 14:48:26 thread.c:285:check_hashrate: latest avg rate < 0.98......
2020-05-03 14:48:26 thread.c:286:check_hashrate: current PCB min temperature 37
2020-05-03 14:48:26 thread.c:287:check_hashrate: current voltage is 17.20V, working voltage is 17.20V
2020-05-03 14:48:26 thread.c:312:check_hashrate: high temp, voltage has already increased 0.1V/0.2V

Miner Status Page: https://drive.google.com/file/d/1bjfGsFdSOzZLzp9nSr2eEqf4AadNwMe3/view?usp=sharing

Jacob


Mikey, I'll take you up and can  you show me how to change the fan speed to 100%? Can you do it on Stock firmware?

Jacob