Randomly dropping one board on s17e

[PopoJeff]

Hey gang.

On my s17e 64, it'll run just fine for about two days, then it'll drop a board. I do a reboot and it recovers fine. Runs another 2-3 days, and drops a board again. Still under warranty. Any ideas if this is something I can remedy, or ship it out for repair?

Here's a sample of the log, when running just fine:

Code:

io907
2020-01-25 22:30:35 power_api.c:318:set_to_check_asic_voltage: Set to voltage raw 1800, one step.
2020-01-25 22:30:52 uart.c:69:set_baud: set UART baud to 115200
2020-01-25 22:30:59 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[0]: find 135 asic, times 0
2020-01-25 22:31:06 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[1]: find 135 asic, times 0
2020-01-25 22:31:13 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[2]: find 135 asic, times 0
2020-01-25 22:31:13 power_api.c:336:set_to_highest_voltage_by_steps: Set to voltage raw 2000, step by step.
2020-01-25 22:32:00 driver-hash-chip.c:433:set_uart_relay: set uart relay to 0x390003
2020-01-25 22:32:01 driver-hash-chip.c:821:set_ldo_ctrl: Set LDO to 0x2000203

But when it drops the one board, the italicized line reads:  Chain [2]: find 000 asic, ....

I'm not seeing any errors pop up when that occurs. My other 3 s17's have been running like a Swiss clock (Pro50, and two S17+)

Edit:  Bitmains trouble-shooting guide (mostly related to S9's) shows "make sure cables are good and properly placed" as a solution.

[1714977378]

1714977378

[1714977378]

1714977378

[1714977378]

1714977378

[BitMaxz]

Much better to put the whole kernel logs on pastebin.com and post it here or use the insert code from message box here and post it here

It looks like this:

or use the button

Then post

Also, make a screenshot of your miner status and post it here.


Antminer has high temp protection mode that might be the cause of your miner stop mining. If it just a one board getting 0 asic and all miner stop then it was a temp protection mode but if it still running with drop hashrate you might have a defective hashboard.

However, if you can put all of your kernel logs and some screenshot here maybe we can find what is the cause of hash rate drop.

[PopoJeff]

Thanks, here we go...  couldn't get the whole page to copy, but I got the bottom majority.  Enough you can see the reboot I did just before my original post, and the recovery to normal, and to now, where it dropped a board again.

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203428K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25948K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12908K (cce65000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 2863239596
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 789016DF-956B-4FC7-BD75-88461A74F46B, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 74/39, WL threshold: 4096, image sequence number: 614900815
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 91DF6B3D-1A99-4241-87C7-EB25097110C1, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2020-01-25 22:29:37 driver-btm-api.c:486:init_freq_mode: This is scan-user version
2020-01-25 22:29:37 driver-btm-api.c:1784:bitmain_soc_init: Miner compile time: Sat Nov  2 00:57:07 CST 2019 type: Antminer S17e
2020-01-25 22:29:37 driver-btm-api.c:1785:bitmain_soc_init: commit version: 3658412 2019-11-01 22:33:08, build by: lol 2019-11-02 01:07:07
2020-01-25 22:29:37 driver-btm-api.c:1786:bitmain_soc_init: opt_multi_version     = 1
2020-01-25 22:29:37 driver-btm-api.c:1787:bitmain_soc_init: opt_bitmain_ab        = 1
2020-01-25 22:29:37 driver-btm-api.c:1788:bitmain_soc_init: mid_auto_gen          = 0
2020-01-25 22:29:37 driver-btm-api.c:1789:bitmain_soc_init: opt_bitmain_work_mode = 0
2020-01-25 22:29:37 driver-btm-api.c:1613:show_sn: no SN got, please write SN to /nvdata/sn
2020-01-25 22:29:37 fan.c:248:front_fan_power_on: Note: front fan is power on!
2020-01-25 22:29:37 fan.c:260:rear_fan_power_on: Note: rear fan is power on!
2020-01-25 22:29:37 driver-btm-api.c:949:miner_device_init: Detect 256MB control board of XILINX
2020-01-25 22:29:37 driver-btm-api.c:897:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-01-25 22:29:37 thread.c:705:create_read_nonce_reg_thread: create thread
2020-01-25 22:29:43 driver-btm-api.c:881:init_miner_version: miner ID : 8162552a18c08854
2020-01-25 22:29:43 driver-btm-api.c:887:init_miner_version: FPGA Version = 0xB023
2020-01-25 22:29:45 [chain 0]
0x0000 96 13 01 00 59 44 46 54   59 48 36 41 49 41 41 4A 
0x0010 42 30 47 4C 33 00 00 00   28 01 00 01 01 01 01 04 
0x0020 04 41 42 5A 5A 5A A5 E7   96 13 56 56 56 56 56 56 
0x0030 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0040 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0050 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0060 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0070 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0080 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0090 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x00A0 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x00B0 56 3A 07 7B 56 00 00 00   00 01 00 FF FF FF FF FF 
0x00C0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00D0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00E0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00F0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF 42 9B 

2020-01-25 22:29:45 fixture_header                 : 0x1396
2020-01-25 22:29:45 fixture_version                : 0x0001
2020-01-25 22:29:45 hash_board_sn                  : YDFTYH6AIAAJB0GL3
2020-01-25 22:29:45 pcb_version                    : 0x0128
2020-01-25 22:29:45 bom_version                    : 0x0100
2020-01-25 22:29:45 product_id                     : 0x01
2020-01-25 22:29:45 board_bin                      : 0x01
2020-01-25 22:29:45 
2020-01-25 22:29:45 miner_header                   : 0x1396
2020-01-25 22:29:45 work_mode_count                : 0x01
2020-01-25 22:29:45 miner_bin                      : 0x00
2020-01-25 22:29:45 [mode 0]
2020-01-25 22:29:45 voltage                        : 1850
2020-01-25 22:29:45 ideal_hash_rate                : 22139
IC[000]:430 IC[001]:430 IC[002]:430 IC[003]:430 IC[004]:430 IC[005]:430 IC[006]:430 IC[007]:430 IC[008]:430 
IC[009]:430 IC[010]:430 IC[011]:430 IC[012]:430 IC[013]:430 IC[014]:430 IC[015]:430 IC[016]:430 IC[017]:430 
IC[018]:430 IC[019]:430 IC[020]:430 IC[021]:430 IC[022]:430 IC[023]:430 IC[024]:430 IC[025]:430 IC[026]:430 
IC[027]:430 IC[028]:430 IC[029]:430 IC[030]:430 IC[031]:430 IC[032]:430 IC[033]:430 IC[034]:430 IC[035]:430 
IC[036]:430 IC[037]:430 IC[038]:430 IC[039]:430 IC[040]:430 IC[041]:430 IC[042]:430 IC[043]:430 IC[044]:430 
IC[045]:430 IC[046]:430 IC[047]:430 IC[048]:430 IC[049]:430 IC[050]:430 IC[051]:430 IC[052]:430 IC[053]:430 
IC[054]:430 IC[055]:430 IC[056]:430 IC[057]:430 IC[058]:430 IC[059]:430 IC[060]:430 IC[061]:430 IC[062]:430 
IC[063]:430 IC[064]:430 IC[065]:430 IC[066]:430 IC[067]:430 IC[068]:430 IC[069]:430 IC[070]:430 IC[071]:430 
IC[072]:430 IC[073]:430 IC[074]:430 IC[075]:430 IC[076]:430 IC[077]:430 IC[078]:430 IC[079]:430 IC[080]:430 
IC[081]:430 IC[082]:430 IC[083]:430 IC[084]:430 IC[085]:430 IC[086]:430 IC[087]:430 IC[088]:430 IC[089]:430 
IC[090]:430 IC[091]:430 IC[092]:430 IC[093]:430 IC[094]:430 IC[095]:430 IC[096]:430 IC[097]:430 IC[098]:430 
IC[099]:430 IC[100]:430 IC[101]:430 IC[102]:430 IC[103]:430 IC[104]:430 IC[105]:430 IC[106]:430 IC[107]:430 
IC[108]:430 IC[109]:430 IC[110]:430 IC[111]:430 IC[112]:430 IC[113]:430 IC[114]:430 IC[115]:430 IC[116]:430 
IC[117]:430 IC[118]:430 IC[119]:430 IC[120]:430 IC[121]:430 IC[122]:430 IC[123]:430 IC[124]:430 IC[125]:430 
IC[126]:430 IC[127]:430 IC[128]:430 IC[129]:430 IC[130]:430 IC[131]:430 IC[132]:430 IC[133]:430 IC[134]:430 
2020-01-25 22:29:47 [chain 1]
0x0000 96 13 01 00 59 44 46 54   59 48 36 41 49 41 41 4A 
0x0010 42 30 46 45 4C 00 00 00   28 01 00 01 01 01 01 04 
0x0020 04 41 42 5A 5A 5A 6E 67   96 13 52 52 4E 52 4E 52 
0x0030 52 52 4E 52 4E 52 52 52   52 4E 52 4E 52 52 52 52 
0x0040 52 52 4E 4E 4E 52 4E 52   4E 52 52 52 52 4E 4E 4E 
0x0050 52 52 52 4E 52 52 52 52   4E 4E 52 52 4E 52 52 52 
0x0060 52 52 52 4E 52 4E 52 4E   52 52 52 52 4E 4E 4E 52 
0x0070 52 52 52 52 52 4E 4E 52   52 4E 52 4E 52 4E 52 52 
0x0080 4E 52 52 52 4E 52 52 52   52 4E 52 52 4E 4E 52 4E 
0x0090 52 4E 52 52 52 52 52 52   52 4E 4E 4E 52 52 52 4E 
0x00A0 52 52 4E 52 52 52 52 4E   4E 4E 52 52 52 52 52 4E 
0x00B0 52 3A 07 60 51 00 00 00   00 01 00 FF FF FF FF FF 
0x00C0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00D0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00E0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00F0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF AA DB 

2020-01-25 22:29:47 fixture_header                 : 0x1396
2020-01-25 22:29:47 fixture_version                : 0x0001
2020-01-25 22:29:47 hash_board_sn                  : YDFTYH6AIAAJB0FEL
2020-01-25 22:29:47 pcb_version                    : 0x0128
2020-01-25 22:29:47 bom_version                    : 0x0100
2020-01-25 22:29:47 product_id                     : 0x01
2020-01-25 22:29:47 board_bin                      : 0x01
2020-01-25 22:29:47 
2020-01-25 22:29:47 miner_header                   : 0x1396
2020-01-25 22:29:47 work_mode_count                : 0x01
2020-01-25 22:29:47 miner_bin                      : 0x00
2020-01-25 22:29:47 [mode 0]
2020-01-25 22:29:47 voltage                        : 1850
2020-01-25 22:29:47 ideal_hash_rate                : 20832
IC[000]:410 IC[001]:410 IC[002]:390 IC[003]:410 IC[004]:390 IC[005]:410 IC[006]:410 IC[007]:410 IC[008]:390 
IC[009]:410 IC[010]:390 IC[011]:410 IC[012]:410 IC[013]:410 IC[014]:410 IC[015]:390 IC[016]:410 IC[017]:390 
IC[018]:410 IC[019]:410 IC[020]:410 IC[021]:410 IC[022]:410 IC[023]:410 IC[024]:390 IC[025]:390 IC[026]:390 
IC[027]:410 IC[028]:390 IC[029]:410 IC[030]:390 IC[031]:410 IC[032]:410 IC[033]:410 IC[034]:410 IC[035]:390 
IC[036]:390 IC[037]:390 IC[038]:410 IC[039]:410 IC[040]:410 IC[041]:390 IC[042]:410 IC[043]:410 IC[044]:410 
IC[045]:410 IC[046]:390 IC[047]:390 IC[048]:410 IC[049]:410 IC[050]:390 IC[051]:410 IC[052]:410 IC[053]:410 
IC[054]:410 IC[055]:410 IC[056]:410 IC[057]:390 IC[058]:410 IC[059]:390 IC[060]:410 IC[061]:390 IC[062]:410 
IC[063]:410 IC[064]:410 IC[065]:410 IC[066]:390 IC[067]:390 IC[068]:390 IC[069]:410 IC[070]:410 IC[071]:410 
IC[072]:410 IC[073]:410 IC[074]:410 IC[075]:390 IC[076]:390 IC[077]:410 IC[078]:410 IC[079]:390 IC[080]:410 
IC[081]:390 IC[082]:410 IC[083]:390 IC[084]:410 IC[085]:410 IC[086]:390 IC[087]:410 IC[088]:410 IC[089]:410 
IC[090]:390 IC[091]:410 IC[092]:410 IC[093]:410 IC[094]:410 IC[095]:390 IC[096]:410 IC[097]:410 IC[098]:390 
IC[099]:390 IC[100]:410 IC[101]:390 IC[102]:410 IC[103]:390 IC[104]:410 IC[105]:410 IC[106]:410 IC[107]:410 
IC[108]:410 IC[109]:410 IC[110]:410 IC[111]:390 IC[112]:390 IC[113]:390 IC[114]:410 IC[115]:410 IC[116]:410 
IC[117]:390 IC[118]:410 IC[119]:410 IC[120]:390 IC[121]:410 IC[122]:410 IC[123]:410 IC[124]:410 IC[125]:390 
IC[126]:390 IC[127]:390 IC[128]:410 IC[129]:410 IC[130]:410 IC[131]:410 IC[132]:410 IC[133]:390 IC[134]:410 
2020-01-25 22:29:48 [chain 2]
0x0000 96 13 01 00 59 44 46 54   59 48 36 41 49 41 41 4A 
0x0010 42 30 46 45 43 00 00 00   28 01 00 01 01 01 01 04 
0x0020 04 41 42 5A 5A 5A 5D 70   96 13 5A 5A 5A 5A 5A 5A 
0x0030 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0040 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0050 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0060 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0070 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0080 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0090 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x00A0 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x00B0 5A 3A 07 B0 5A 00 00 00   00 01 00 FF FF FF FF FF 
0x00C0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00D0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00E0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00F0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF B8 22 

2020-01-25 22:29:48 fixture_header                 : 0x1396
2020-01-25 22:29:48 fixture_version                : 0x0001
2020-01-25 22:29:48 hash_board_sn                  : YDFTYH6AIAAJB0FEC
2020-01-25 22:29:48 pcb_version                    : 0x0128
2020-01-25 22:29:48 bom_version                    : 0x0100
2020-01-25 22:29:48 product_id                     : 0x01
2020-01-25 22:29:48 board_bin                      : 0x01
2020-01-25 22:29:48 
2020-01-25 22:29:48 miner_header                   : 0x1396
2020-01-25 22:29:48 work_mode_count                : 0x01
2020-01-25 22:29:48 miner_bin                      : 0x00
2020-01-25 22:29:48 [mode 0]
2020-01-25 22:29:48 voltage                        : 1850
2020-01-25 22:29:48 ideal_hash_rate                : 23216
IC[000]:450 IC[001]:450 IC[002]:450 IC[003]:450 IC[004]:450 IC[005]:450 IC[006]:450 IC[007]:450 IC[008]:450 
IC[009]:450 IC[010]:450 IC[011]:450 IC[012]:450 IC[013]:450 IC[014]:450 IC[015]:450 IC[016]:450 IC[017]:450 
IC[018]:450 IC[019]:450 IC[020]:450 IC[021]:450 IC[022]:450 IC[023]:450 IC[024]:450 IC[025]:450 IC[026]:450 
IC[027]:450 IC[028]:450 IC[029]:450 IC[030]:450 IC[031]:450 IC[032]:450 IC[033]:450 IC[034]:450 IC[035]:450 
IC[036]:450 IC[037]:450 IC[038]:450 IC[039]:450 IC[040]:450 IC[041]:450 IC[042]:450 IC[043]:450 IC[044]:450 
IC[045]:450 IC[046]:450 IC[047]:450 IC[048]:450 IC[049]:450 IC[050]:450 IC[051]:450 IC[052]:450 IC[053]:450 
IC[054]:450 IC[055]:450 IC[056]:450 IC[057]:450 IC[058]:450 IC[059]:450 IC[060]:450 IC[061]:450 IC[062]:450 
IC[063]:450 IC[064]:450 IC[065]:450 IC[066]:450 IC[067]:450 IC[068]:450 IC[069]:450 IC[070]:450 IC[071]:450 
IC[072]:450 IC[073]:450 IC[074]:450 IC[075]:450 IC[076]:450 IC[077]:450 IC[078]:450 IC[079]:450 IC[080]:450 
IC[081]:450 IC[082]:450 IC[083]:450 IC[084]:450 IC[085]:450 IC[086]:450 IC[087]:450 IC[088]:450 IC[089]:450 
IC[090]:450 IC[091]:450 IC[092]:450 IC[093]:450 IC[094]:450 IC[095]:450 IC[096]:450 IC[097]:450 IC[098]:450 
IC[099]:450 IC[100]:450 IC[101]:450 IC[102]:450 IC[103]:450 IC[104]:450 IC[105]:450 IC[106]:450 IC[107]:450 
IC[108]:450 IC[109]:450 IC[110]:450 IC[111]:450 IC[112]:450 IC[113]:450 IC[114]:450 IC[115]:450 IC[116]:450 
IC[117]:450 IC[118]:450 IC[119]:450 IC[120]:450 IC[121]:450 IC[122]:450 IC[123]:450 IC[124]:450 IC[125]:450 
IC[126]:450 IC[127]:450 IC[128]:450 IC[129]:450 IC[130]:450 IC[131]:450 IC[132]:450 IC[133]:450 IC[134]:450 
2020-01-25 22:29:48 driver-btm-api.c:522:get_product_id: product_id[0] = 1
2020-01-25 22:29:48 driver-btm-api.c:522:get_product_id: product_id[1] = 1
2020-01-25 22:29:48 driver-btm-api.c:522:get_product_id: product_id[2] = 1
2020-01-25 22:29:48 driver-btm-api.c:502:dump_pcb_bom_version: Chain [0] PCB Version: 0x0128
2020-01-25 22:29:48 driver-btm-api.c:503:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-01-25 22:29:48 driver-btm-api.c:502:dump_pcb_bom_version: Chain [1] PCB Version: 0x0128
2020-01-25 22:29:48 driver-btm-api.c:503:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-01-25 22:29:48 driver-btm-api.c:502:dump_pcb_bom_version: Chain [2] PCB Version: 0x0128
2020-01-25 22:29:48 driver-btm-api.c:503:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-01-25 22:29:52 driver-btm-api.c:1735:bitmain_board_init: Fan check passed.
2020-01-25 22:29:54 board.c:48:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-01-25 22:29:56 board.c:60:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-01-25 22:29:57 board.c:48:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-01-25 22:29:59 board.c:60:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-01-25 22:30:00 board.c:48:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-01-25 22:30:02 board.c:60:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-01-25 22:30:02 thread.c:700:create_pic_heart_beat_thread: create thread
2020-01-25 22:30:03 power_api.c:243:power_init: power type version: 0x0042
2020-01-25 22:30:03 power_api.c:261:power_init: Power init:
2020-01-25 22:30:03 power_api.c:262:power_init: current_voltage_raw     = 0
2020-01-25 22:30:03 power_api.c:263:power_init: highest_voltage_raw     = 2000
2020-01-25 22:30:03 power_api.c:264:power_init: working_voltage_raw     = 2000
2020-01-25 22:30:03 power_api.c:265:power_init: higher_voltage_raw      = 1850
2020-01-25 22:30:03 power_api.c:266:power_init: check_asic_voltage_raw  = 1800
2020-01-25 22:30:03 driver-btm-api.c:1745:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-01-25 22:30:03 power_api.c:231:power_off: init gpio907
2020-01-25 22:30:35 power_api.c:318:set_to_check_asic_voltage: Set to voltage raw 1800, one step.
2020-01-25 22:30:52 uart.c:69:set_baud: set UART baud to 115200
2020-01-25 22:30:59 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[0]: find 135 asic, times 0
2020-01-25 22:31:06 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[1]: find 135 asic, times 0
2020-01-25 22:31:13 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[2]: find 135 asic, times 0
2020-01-25 22:31:13 power_api.c:336:set_to_highest_voltage_by_steps: Set to voltage raw 2000, step by step.
2020-01-25 22:32:00 driver-hash-chip.c:433:set_uart_relay: set uart relay to 0x390003
2020-01-25 22:32:01 driver-hash-chip.c:821:set_ldo_ctrl: Set LDO to 0x2000203
2020-01-25 22:32:01 voltage[0] = 1850
2020-01-25 22:32:01 voltage[1] = 1850
2020-01-25 22:32:01 voltage[2] = 1850
2020-01-25 22:32:01 power_api.c:274:set_working_voltage_raw: working_voltage_raw = 1850
2020-01-25 22:32:02 temperature.c:297:calibrate_temp_sensor_one_chain: chain 0 temp sensor NCT218
2020-01-25 22:32:03 temperature.c:297:calibrate_temp_sensor_one_chain: chain 1 temp sensor NCT218
2020-01-25 22:32:05 temperature.c:297:calibrate_temp_sensor_one_chain: chain 2 temp sensor NCT218
2020-01-25 22:32:05 uart.c:69:set_baud: set UART baud to 12000000
2020-01-25 22:32:07 driver-btm-api.c:228:check_bringup_temp: Bring up temperature is 23
2020-01-25 22:32:07 thread.c:720:create_check_miner_status_thread: create thread
2020-01-25 22:32:07 thread.c:710:create_show_miner_status_thread: create thread
2020-01-25 22:32:07 thread.c:695:create_temperature_monitor_thread: create thread
2020-01-25 22:32:07 sweep.c:960:sweep_get_max_freq: max_freq = 480
2020-01-25 22:32:07 frequency.c:472:inc_freq_with_fixed_vco: chain = 255, freq = 390, is_higher_voltage = true
2020-01-25 22:32:07 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 2100, step by step.
2020-01-25 22:32:37 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1950, step by step.
2020-01-25 22:33:00 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1900, step by step.
2020-01-25 22:33:19 frequency.c:507:inc_freq_with_fixed_step: chain = 0, freq_start = 390, freq_end = 430, freq_step = 5, is_higher_voltage = true
2020-01-25 22:33:20 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1880, step by step.
2020-01-25 22:33:37 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1860, step by step.
2020-01-25 22:33:56 frequency.c:507:inc_freq_with_fixed_step: chain = 2, freq_start = 390, freq_end = 430, freq_step = 5, is_higher_voltage = true
2020-01-25 22:33:56 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1880, step by step.
2020-01-25 22:34:13 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1900, step by step.
2020-01-25 22:34:30 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1880, step by step.
2020-01-25 22:34:49 frequency.c:507:inc_freq_with_fixed_step: chain = 2, freq_start = 430, freq_end = 450, freq_step = 5, is_higher_voltage = true
2020-01-25 22:34:51 frequency.c:348:inc_asic_diff_freq_by_steps: chain = 1, start = 390, freq_step = 5
2020-01-25 22:34:55 driver-btm-api.c:470:set_timeout: freq = 450, percent = 90, hcn = 235928, timeout = 524
2020-01-25 22:34:55 power_api.c:330:set_to_working_voltage_by_steps: Set to voltage raw 1850, step by step.
2020-01-25 22:35:11 thread.c:715:create_check_system_status_thread: create thread
2020-01-25 22:35:12 driver-btm-api.c:1894:bitmain_soc_init: Init done!
2020-01-25 22:35:12 driver-btm-api.c:186:set_miner_status: STATUS_INIT
2020-01-25 22:35:17 driver-btm-api.c:186:set_miner_status: STATUS_OKAY
2020-01-25 22:35:18 frequency.c:161:get_ideal_hash_rate_GH: ideal_hash_rate = 66187
2020-01-25 22:35:18 frequency.c:180:get_sale_hash_rate_GH: sale_hash_rate = 64000
2020-01-25 22:35:22 driver-btm-api.c:1214:dhash_chip_send_job: Version num 8
2020-01-25 23:05:24 thread.c:188:calc_hashrate_avg: avg rate is 61566.77 in 30 mins
2020-01-25 23:05:24 temperature.c:465:temp_statistics_show:   pcb temp 31~66  chip temp 48~70
2020-01-25 23:05:24 thread.c:269:check_hashrate: latest avg rate < 0.98......
2020-01-25 23:05:24 thread.c:270:check_hashrate: current PCB min temperature 31
2020-01-25 23:05:24 thread.c:271:check_hashrate: current voltage raw is 1850, working voltage raw is 1850
2020-01-25 23:05:24 thread.c:302:check_hashrate: high temp, increase voltage 0.1V/0.2V to 1860
2020-01-25 23:05:24 driver-btm-api.c:1905:bitmain_reopen_core: reopen_core start!
2020-01-25 23:05:30 driver-btm-api.c:881:init_miner_version: miner ID : 8162552a18c08854
2020-01-25 23:05:30 driver-btm-api.c:887:init_miner_version: FPGA Version = 0xB023
2020-01-25 23:05:32 [chain 0]
0x0000 96 13 01 00 59 44 46 54   59 48 36 41 49 41 41 4A 
0x0010 42 30 47 4C 33 00 00 00   28 01 00 01 01 01 01 04 
0x0020 04 41 42 5A 5A 5A A5 E7   96 13 56 56 56 56 56 56 
0x0030 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0040 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0050 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0060 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0070 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0080 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x0090 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x00A0 56 56 56 56 56 56 56 56   56 56 56 56 56 56 56 56 
0x00B0 56 3A 07 7B 56 00 00 00   00 01 00 FF FF FF FF FF 
0x00C0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00D0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00E0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00F0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF 42 9B 

2020-01-25 23:05:32 fixture_header                 : 0x1396
2020-01-25 23:05:32 fixture_version                : 0x0001
2020-01-25 23:05:32 hash_board_sn                  : YDFTYH6AIAAJB0GL3
2020-01-25 23:05:32 pcb_version                    : 0x0128
2020-01-25 23:05:32 bom_version                    : 0x0100
2020-01-25 23:05:32 product_id                     : 0x01
2020-01-25 23:05:32 board_bin                      : 0x01
2020-01-25 23:05:32 
2020-01-25 23:05:32 miner_header                   : 0x1396
2020-01-25 23:05:32 work_mode_count                : 0x01
2020-01-25 23:05:32 miner_bin                      : 0x00
2020-01-25 23:05:32 [mode 0]
2020-01-25 23:05:32 voltage                        : 1850
2020-01-25 23:05:32 ideal_hash_rate                : 22139
IC[000]:430 IC[001]:430 IC[002]:430 IC[003]:430 IC[004]:430 IC[005]:430 IC[006]:430 IC[007]:430 IC[008]:430 
IC[009]:430 IC[010]:430 IC[011]:430 IC[012]:430 IC[013]:430 IC[014]:430 IC[015]:430 IC[016]:430 IC[017]:430 
IC[018]:430 IC[019]:430 IC[020]:430 IC[021]:430 IC[022]:430 IC[023]:430 IC[024]:430 IC[025]:430 IC[026]:430 
IC[027]:430 IC[028]:430 IC[029]:430 IC[030]:430 IC[031]:430 IC[032]:430 IC[033]:430 IC[034]:430 IC[035]:430 
IC[036]:430 IC[037]:430 IC[038]:430 IC[039]:430 IC[040]:430 IC[041]:430 IC[042]:430 IC[043]:430 IC[044]:430 
IC[045]:430 IC[046]:430 IC[047]:430 IC[048]:430 IC[049]:430 IC[050]:430 IC[051]:430 IC[052]:430 IC[053]:430 
IC[054]:430 IC[055]:430 IC[056]:430 IC[057]:430 IC[058]:430 IC[059]:430 IC[060]:430 IC[061]:430 IC[062]:430 
IC[063]:430 IC[064]:430 IC[065]:430 IC[066]:430 IC[067]:430 IC[068]:430 IC[069]:430 IC[070]:430 IC[071]:430 
IC[072]:430 IC[073]:430 IC[074]:430 IC[075]:430 IC[076]:430 IC[077]:430 IC[078]:430 IC[079]:430 IC[080]:430 
IC[081]:430 IC[082]:430 IC[083]:430 IC[084]:430 IC[085]:430 IC[086]:430 IC[087]:430 IC[088]:430 IC[089]:430 
IC[090]:430 IC[091]:430 IC[092]:430 IC[093]:430 IC[094]:430 IC[095]:430 IC[096]:430 IC[097]:430 IC[098]:430 
IC[099]:430 IC[100]:430 IC[101]:430 IC[102]:430 IC[103]:430 IC[104]:430 IC[105]:430 IC[106]:430 IC[107]:430 
IC[108]:430 IC[109]:430 IC[110]:430 IC[111]:430 IC[112]:430 IC[113]:430 IC[114]:430 IC[115]:430 IC[116]:430 
IC[117]:430 IC[118]:430 IC[119]:430 IC[120]:430 IC[121]:430 IC[122]:430 IC[123]:430 IC[124]:430 IC[125]:430 
IC[126]:430 IC[127]:430 IC[128]:430 IC[129]:430 IC[130]:430 IC[131]:430 IC[132]:430 IC[133]:430 IC[134]:430 
2020-01-25 23:05:33 [chain 1]
0x0000 96 13 01 00 59 44 46 54   59 48 36 41 49 41 41 4A 
0x0010 42 30 46 45 4C 00 00 00   28 01 00 01 01 01 01 04 
0x0020 04 41 42 5A 5A 5A 6E 67   96 13 52 52 4E 52 4E 52 
0x0030 52 52 4E 52 4E 52 52 52   52 4E 52 4E 52 52 52 52 
0x0040 52 52 4E 4E 4E 52 4E 52   4E 52 52 52 52 4E 4E 4E 
0x0050 52 52 52 4E 52 52 52 52   4E 4E 52 52 4E 52 52 52 
0x0060 52 52 52 4E 52 4E 52 4E   52 52 52 52 4E 4E 4E 52 
0x0070 52 52 52 52 52 4E 4E 52   52 4E 52 4E 52 4E 52 52 
0x0080 4E 52 52 52 4E 52 52 52   52 4E 52 52 4E 4E 52 4E 
0x0090 52 4E 52 52 52 52 52 52   52 4E 4E 4E 52 52 52 4E 
0x00A0 52 52 4E 52 52 52 52 4E   4E 4E 52 52 52 52 52 4E 
0x00B0 52 3A 07 60 51 00 00 00   00 01 00 FF FF FF FF FF 
0x00C0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00D0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00E0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00F0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF AA DB 

2020-01-25 23:05:33 fixture_header                 : 0x1396
2020-01-25 23:05:33 fixture_version                : 0x0001
2020-01-25 23:05:33 hash_board_sn                  : YDFTYH6AIAAJB0FEL
2020-01-25 23:05:33 pcb_version                    : 0x0128
2020-01-25 23:05:33 bom_version                    : 0x0100
2020-01-25 23:05:33 product_id                     : 0x01
2020-01-25 23:05:33 board_bin                      : 0x01
2020-01-25 23:05:33 
2020-01-25 23:05:33 miner_header                   : 0x1396
2020-01-25 23:05:33 work_mode_count                : 0x01
2020-01-25 23:05:33 miner_bin                      : 0x00
2020-01-25 23:05:33 [mode 0]
2020-01-25 23:05:33 voltage                        : 1850
2020-01-25 23:05:33 ideal_hash_rate                : 20832
IC[000]:410 IC[001]:410 IC[002]:390 IC[003]:410 IC[004]:390 IC[005]:410 IC[006]:410 IC[007]:410 IC[008]:390 
IC[009]:410 IC[010]:390 IC[011]:410 IC[012]:410 IC[013]:410 IC[014]:410 IC[015]:390 IC[016]:410 IC[017]:390 
IC[018]:410 IC[019]:410 IC[020]:410 IC[021]:410 IC[022]:410 IC[023]:410 IC[024]:390 IC[025]:390 IC[026]:390 
IC[027]:410 IC[028]:390 IC[029]:410 IC[030]:390 IC[031]:410 IC[032]:410 IC[033]:410 IC[034]:410 IC[035]:390 
IC[036]:390 IC[037]:390 IC[038]:410 IC[039]:410 IC[040]:410 IC[041]:390 IC[042]:410 IC[043]:410 IC[044]:410 
IC[045]:410 IC[046]:390 IC[047]:390 IC[048]:410 IC[049]:410 IC[050]:390 IC[051]:410 IC[052]:410 IC[053]:410 
IC[054]:410 IC[055]:410 IC[056]:410 IC[057]:390 IC[058]:410 IC[059]:390 IC[060]:410 IC[061]:390 IC[062]:410 
IC[063]:410 IC[064]:410 IC[065]:410 IC[066]:390 IC[067]:390 IC[068]:390 IC[069]:410 IC[070]:410 IC[071]:410 
IC[072]:410 IC[073]:410 IC[074]:410 IC[075]:390 IC[076]:390 IC[077]:410 IC[078]:410 IC[079]:390 IC[080]:410 
IC[081]:390 IC[082]:410 IC[083]:390 IC[084]:410 IC[085]:410 IC[086]:390 IC[087]:410 IC[088]:410 IC[089]:410 
IC[090]:390 IC[091]:410 IC[092]:410 IC[093]:410 IC[094]:410 IC[095]:390 IC[096]:410 IC[097]:410 IC[098]:390 
IC[099]:390 IC[100]:410 IC[101]:390 IC[102]:410 IC[103]:390 IC[104]:410 IC[105]:410 IC[106]:410 IC[107]:410 
IC[108]:410 IC[109]:410 IC[110]:410 IC[111]:390 IC[112]:390 IC[113]:390 IC[114]:410 IC[115]:410 IC[116]:410 
IC[117]:390 IC[118]:410 IC[119]:410 IC[120]:390 IC[121]:410 IC[122]:410 IC[123]:410 IC[124]:410 IC[125]:390 
IC[126]:390 IC[127]:390 IC[128]:410 IC[129]:410 IC[130]:410 IC[131]:410 IC[132]:410 IC[133]:390 IC[134]:410 
2020-01-25 23:05:35 [chain 2]
0x0000 96 13 01 00 59 44 46 54   59 48 36 41 49 41 41 4A 
0x0010 42 30 46 45 43 00 00 00   28 01 00 01 01 01 01 04 
0x0020 04 41 42 5A 5A 5A 5D 70   96 13 5A 5A 5A 5A 5A 5A 
0x0030 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0040 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0050 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0060 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0070 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0080 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x0090 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x00A0 5A 5A 5A 5A 5A 5A 5A 5A   5A 5A 5A 5A 5A 5A 5A 5A 
0x00B0 5A 3A 07 B0 5A 00 00 00   00 01 00 FF FF FF FF FF 
0x00C0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00D0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00E0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
0x00F0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF B8 22 

2020-01-25 23:05:35 fixture_header                 : 0x1396
2020-01-25 23:05:35 fixture_version                : 0x0001
2020-01-25 23:05:35 hash_board_sn                  : YDFTYH6AIAAJB0FEC
2020-01-25 23:05:35 pcb_version                    : 0x0128
2020-01-25 23:05:35 bom_version                    : 0x0100
2020-01-25 23:05:35 product_id                     : 0x01
2020-01-25 23:05:35 board_bin                      : 0x01
2020-01-25 23:05:35 
2020-01-25 23:05:35 miner_header                   : 0x1396
2020-01-25 23:05:35 work_mode_count                : 0x01
2020-01-25 23:05:35 miner_bin                      : 0x00
2020-01-25 23:05:35 [mode 0]
2020-01-25 23:05:35 voltage                        : 1850
2020-01-25 23:05:35 ideal_hash_rate                : 23216
IC[000]:450 IC[001]:450 IC[002]:450 IC[003]:450 IC[004]:450 IC[005]:450 IC[006]:450 IC[007]:450 IC[008]:450 
IC[009]:450 IC[010]:450 IC[011]:450 IC[012]:450 IC[013]:450 IC[014]:450 IC[015]:450 IC[016]:450 IC[017]:450 
IC[018]:450 IC[019]:450 IC[020]:450 IC[021]:450 IC[022]:450 IC[023]:450 IC[024]:450 IC[025]:450 IC[026]:450 
IC[027]:450 IC[028]:450 IC[029]:450 IC[030]:450 IC[031]:450 IC[032]:450 IC[033]:450 IC[034]:450 IC[035]:450 
IC[036]:450 IC[037]:450 IC[038]:450 IC[039]:450 IC[040]:450 IC[041]:450 IC[042]:450 IC[043]:450 IC[044]:450 
IC[045]:450 IC[046]:450 IC[047]:450 IC[048]:450 IC[049]:450 IC[050]:450 IC[051]:450 IC[052]:450 IC[053]:450 
IC[054]:450 IC[055]:450 IC[056]:450 IC[057]:450 IC[058]:450 IC[059]:450 IC[060]:450 IC[061]:450 IC[062]:450 
IC[063]:450 IC[064]:450 IC[065]:450 IC[066]:450 IC[067]:450 IC[068]:450 IC[069]:450 IC[070]:450 IC[071]:450 
IC[072]:450 IC[073]:450 IC[074]:450 IC[075]:450 IC[076]:450 IC[077]:450 IC[078]:450 IC[079]:450 IC[080]:450 
IC[081]:450 IC[082]:450 IC[083]:450 IC[084]:450 IC[085]:450 IC[086]:450 IC[087]:450 IC[088]:450 IC[089]:450 
IC[090]:450 IC[091]:450 IC[092]:450 IC[093]:450 IC[094]:450 IC[095]:450 IC[096]:450 IC[097]:450 IC[098]:450 
IC[099]:450 IC[100]:450 IC[101]:450 IC[102]:450 IC[103]:450 IC[104]:450 IC[105]:450 IC[106]:450 IC[107]:450 
IC[108]:450 IC[109]:450 IC[110]:450 IC[111]:450 IC[112]:450 IC[113]:450 IC[114]:450 IC[115]:450 IC[116]:450 
IC[117]:450 IC[118]:450 IC[119]:450 IC[120]:450 IC[121]:450 IC[122]:450 IC[123]:450 IC[124]:450 IC[125]:450 
IC[126]:450 IC[127]:450 IC[128]:450 IC[129]:450 IC[130]:450 IC[131]:450 IC[132]:450 IC[133]:450 IC[134]:450 
2020-01-25 23:05:35 driver-btm-api.c:522:get_product_id: product_id[0] = 1
2020-01-25 23:05:35 driver-btm-api.c:522:get_product_id: product_id[1] = 1
2020-01-25 23:05:35 driver-btm-api.c:522:get_product_id: product_id[2] = 1
2020-01-25 23:05:35 driver-btm-api.c:502:dump_pcb_bom_version: Chain [0] PCB Version: 0x0128
2020-01-25 23:05:35 driver-btm-api.c:503:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2020-01-25 23:05:35 driver-btm-api.c:502:dump_pcb_bom_version: Chain [1] PCB Version: 0x0128
2020-01-25 23:05:35 driver-btm-api.c:503:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2020-01-25 23:05:35 driver-btm-api.c:502:dump_pcb_bom_version: Chain [2] PCB Version: 0x0128
2020-01-25 23:05:35 driver-btm-api.c:503:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2020-01-25 23:05:37 driver-btm-api.c:1735:bitmain_board_init: Fan check passed.
2020-01-25 23:05:38 board.c:48:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-01-25 23:05:41 board.c:60:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-01-25 23:05:42 board.c:48:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-01-25 23:05:44 board.c:60:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-01-25 23:05:45 board.c:48:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-01-25 23:05:47 board.c:60:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-01-25 23:05:48 power_api.c:243:power_init: power type version: 0x0042
2020-01-25 23:05:48 power_api.c:261:power_init: Power init:
2020-01-25 23:05:48 power_api.c:262:power_init: current_voltage_raw     = 0
2020-01-25 23:05:48 power_api.c:263:power_init: highest_voltage_raw     = 2000
2020-01-25 23:05:48 power_api.c:264:power_init: working_voltage_raw     = 2000
2020-01-25 23:05:48 power_api.c:265:power_init: higher_voltage_raw      = 1850
2020-01-25 23:05:48 power_api.c:266:power_init: check_asic_voltage_raw  = 1800
2020-01-25 23:05:48 driver-btm-api.c:1745:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-01-25 23:06:20 power_api.c:318:set_to_check_asic_voltage: Set to voltage raw 1800, one step.
2020-01-25 23:06:29 power_api.c:96:check_voltage: target_vol = 18.00, actural_vol = 11.22, more than 0.5v diff.
2020-01-25 23:06:44 uart.c:69:set_baud: set UART baud to 115200
2020-01-25 23:06:51 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[0]: find 135 asic, times 0
2020-01-25 23:06:58 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[1]: find 135 asic, times 0
2020-01-25 23:07:05 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 0
2020-01-25 23:07:06 board.c:48:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-01-25 23:07:08 board.c:60:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-01-25 23:07:16 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 1
2020-01-25 23:07:17 board.c:48:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-01-25 23:07:19 board.c:60:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-01-25 23:07:26 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 2
2020-01-25 23:07:27 board.c:48:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-01-25 23:07:29 board.c:60:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-01-25 23:07:29 driver-btm-api.c:851:check_asic_number: Chain 2 only find 0 asic, will power off hash board 2
2020-01-25 23:07:30 power_api.c:336:set_to_highest_voltage_by_steps: Set to voltage raw 2000, step by step.
2020-01-25 23:08:06 driver-hash-chip.c:433:set_uart_relay: set uart relay to 0x390003
2020-01-25 23:08:06 driver-hash-chip.c:821:set_ldo_ctrl: Set LDO to 0x2000203
2020-01-25 23:08:06 voltage[0] = 1850
2020-01-25 23:08:06 voltage[1] = 1850
2020-01-25 23:08:06 power_api.c:274:set_working_voltage_raw: working_voltage_raw = 1850
2020-01-25 23:08:06 frequency.c:161:get_ideal_hash_rate_GH: ideal_hash_rate = 42971
2020-01-25 23:08:06 frequency.c:180:get_sale_hash_rate_GH: sale_hash_rate = 40000
2020-01-25 23:08:07 temperature.c:297:calibrate_temp_sensor_one_chain: chain 0 temp sensor NCT218
2020-01-25 23:08:09 temperature.c:297:calibrate_temp_sensor_one_chain: chain 1 temp sensor NCT218
2020-01-25 23:08:09 uart.c:69:set_baud: set UART baud to 12000000
2020-01-25 23:08:10 driver-btm-api.c:228:check_bringup_temp: Bring up temperature is 23
2020-01-25 23:08:10 frequency.c:472:inc_freq_with_fixed_vco: chain = 255, freq = 390, is_higher_voltage = true
2020-01-25 23:08:10 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 2100, step by step.
2020-01-25 23:08:35 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1950, step by step.
2020-01-25 23:08:53 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1900, step by step.
2020-01-25 23:09:07 frequency.c:507:inc_freq_with_fixed_step: chain = 0, freq_start = 390, freq_end = 430, freq_step = 5, is_higher_voltage = true
2020-01-25 23:09:08 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1880, step by step.
2020-01-25 23:09:22 frequency.c:348:inc_asic_diff_freq_by_steps: chain = 1, start = 390, freq_step = 5
2020-01-25 23:09:27 driver-btm-api.c:470:set_timeout: freq = 430, percent = 90, hcn = 235928, timeout = 548
2020-01-25 23:09:27 power_api.c:330:set_to_working_voltage_by_steps: Set to voltage raw 1850, step by step.
2020-01-25 23:09:39 driver-btm-api.c:1961:bitmain_reopen_core: reopen_core done!
2020-01-25 23:09:39 power_api.c:348:set_to_voltage_by_steps: Set to voltage raw 1860, step by step.
2020-01-25 23:09:50 power_api.c:274:set_working_voltage_raw: working_voltage_raw = 1860
2020-01-25 23:39:51 thread.c:188:calc_hashrate_avg: avg rate is 43172.19 in 30 mins
2020-01-25 23:39:51 temperature.c:465:temp_statistics_show:   pcb temp 32~62  chip temp 49~70

[Steamtyme]

I see your edit in OP about the bitmain solution that's what I was going to bring to the table. I generally lean that way especially when it's sporadic in dropping off, that or something got sucked into the fans and may be causing an obstruction. If you've gone through and secured all cables and made sure the path for airflow is clear, you should definitely get a ticket started, might as well send them the same log you've posted here.
That way you can tell them you've already tried their initial troubleshooting and give them something to look at.
Edit: Does this model have the LP mode? If so have you tried running it and does the same problem occur?

[PopoJeff]

No power modes at all on the e and + models.  Was hoping they'd do a firmware update with those options.

I'll do some screwing around in the morning, open it up and give it a once over.


And here, looks like it couldn't find the board, tested again and found it, and kept running

Code:

2020-01-26 01:03:33 power_api.c:262:power_init: current_voltage_raw     = 0
2020-01-26 01:03:33 power_api.c:263:power_init: highest_voltage_raw     = 2000
2020-01-26 01:03:33 power_api.c:264:power_init: working_voltage_raw     = 2000
2020-01-26 01:03:33 power_api.c:265:power_init: higher_voltage_raw      = 1850
2020-01-26 01:03:33 power_api.c:266:power_init: check_asic_voltage_raw  = 1800
2020-01-26 01:03:33 driver-btm-api.c:1745:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-01-26 01:04:05 power_api.c:318:set_to_check_asic_voltage: Set to voltage raw 1800, one step.
2020-01-26 01:04:21 uart.c:69:set_baud: set UART baud to 115200
2020-01-26 01:04:28 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[0]: find 135 asic, times 0
2020-01-26 01:04:35 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[1]: find 135 asic, times 0
2020-01-26 01:04:42 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 0
2020-01-26 01:04:43 board.c:48:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-01-26 01:04:45 board.c:60:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-01-26 01:04:52 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 1
2020-01-26 01:04:53 board.c:48:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-01-26 01:04:55 board.c:60:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-01-26 01:05:02 driver-btm-api.c:794:check_asic_number_with_power_on: Chain[2]: find 135 asic, times 2
2020-01-26 01:05:02 power_api.c:336:set_to_highest_voltage_by_steps: Set to voltage raw 2000, step by step.
2020-01-26 01:05:49 driver-hash-chip.c:433:set_uart_relay: set uart relay to 0x390003
2020-01-26 01:05:50 driver-hash-chip.c:821:set_ldo_ctrl: Set LDO to 0x2000203
2020-01-26 01:05:50 voltage[0] = 1850
2020-01-26 01:05:50 voltage[1] = 1850
2020-01-26 01:05:50 voltage[2] = 1850

[BitMaxz]

It seems a power failure the PSU not giving enough power or control board failure.

Since this miner is sealed I don't recommend disassembling the unit because it's still under warranty. But you can try this method below and maybe any of these might solve your issue.

Try these 3 possible solutions.

- Do a hard reset (restore default). You can do this by holding the reset button for 5 to 10 seconds then release. After that test it again.

- If the issue still occurs try to check the miner's configuration for work mode something like that where you can choose between (low power, normal and turbo mode) if you found a working mode try to run it at low power mode if the miner become stable try to set it to normal mode then test. If stable stay with that setting.

- Try to flash it with the latest version through WebGUI you can download the firmware from here Antminer-S17e-user-OM-201912251055-sig_5079.tar.gz
Then run and test the miner.

If all of these don't work you have a defective unit you will need to send it back to bitmain for repair/replacement.

[philipma1957]

This is the prefect case of what should  I do.

2 boards work
1 board does not work.

A) do you live in china or close by.
B) do you live in usa.

If you are in USA you will pay  close to 200 to ship it
when it is returned you may get stuck full trump tax.

so do you say eff the rma and buy this

https://shop.bitmain.com/product/detail?pid=00020191211170208469xU07Idx30682

pros of buying a new psu it will cost about  200 usd shipped to you.
you will mine with 2 boards  while you wait

cons of buying a new psu  it may not fix the problem.

pro of sending for a rma
not many maybe 1
you get a working machine in  4 weeks

cons of send for rma

at least a cost of 200 shipping it in
it may cost 300 in trump tax if you are usa based
cost of 500  is possible
plus you lose 2 boards of hash for 4 to 6 weeks

I have a t17+  it has a shaky  third board.

I will soon order a psu for it.

[PopoJeff]

Thanks for the replies so far,  its run just fine all day today, no problems.  So I didnt touch it. Just monitoring every hour or so.

I live USA east coast, near Philly.  It my understanding they have a repair center in CA.

The + and e models have no power settings at all.... no turbo, no low power.

I'll keep monitoring and do the hard reset if it drops again.


Edit 2-2-20:   Since my last post above (1-26-20), its been running fine, no problems.

Edit: 2-23-20:  still running, no problems

[mikeywith]

I'll keep monitoring and do the hard reset if it drops again.

The "e" version of anything bitmain makes is the worst of it's kind, it either the worst performing chips or the normal version over-clocked.

The problem you describe is most likely a power issue, you need a psu to test with, this is why one should always try to get gears that are compatible with one another, the PSUs of your S17+ and Pro don't work for the S17e, so you have no option left but to buy a new PSU.

With that said, the cheapest and fastest step you have now is a hard reset, this could very likely fix your issue, if you don't plan on sending it back to bitmain, try a non-bitmain firmware and see if you get any results.