S9K Stock firmware SSH unlocked + Control fan

[thierry4wd]

Hi all, i'm happy to share my moded files with all ! Please read all before installing !!!

Feature :

-Stock firmware
-SSH unlocked
-Fan control unlocked
-LPM unlocked (but not working on this miner)
-Statut miner page include my mod for monitoring healt miner


For install :

1 : just try upgrade this ! if not work, jump to "2"
2 : Power off miner
3 : Make all this file on SD card and inser on miner (SD Unlocker 17 Family)    ----- https://www.djayos.com -----
4 : WARNING : this files is taken on T17/S17 firmware, please unplug all data cable on all hashboard before power on miner ! (just for inssurance for save hashboard eprom probably)

5 : power on miner, and wait GREEN and RED led flashing
6 : power off miner and remove sd card
7 : power on miner , and flash my firmware ! ----- ask me -----
8 : If all is ok, power off miner, plug all data cable again, and POWER ON !!!



Enjoy !!!  

If you want donate, do not hesitate !!! lol  

[1714805770]

1714805770

[1714805770]

1714805770

[thierry4wd]

Any comment ?

I have forget to say is full free, no dev fee ? no modified firmware 

Just add SSH files for unlock and unlock fan control on minerconfiguration.cgi

Leave comment

[Keezasa]

Does this firmware work on the s9SE version?

[thierry4wd]

i thinks yes ...

i have tested S9SE firmware on S9K with no problem ...

so you don't take a risk if you test it ...

if don't work, just make my "tutorial" and flash your original S9SE firmware

[elfarto69]

Any chance of reuploading the files, they were removed by the upload service!

[thierry4wd]

Hi, i have re uploded files, please leave comment

[elfarto69]

Thanks a lot, will try and report back

Why my GH Target reads 30 TH ? https://iili.io/d2fd41.png

[thierry4wd]

very strange... please give me "full" miner stat image. If your miner have problem before, my mod not solve this...

You have installed on S9K ? my mod is only compatible with S9K and maybe S9SE , any other miners...

[mikeywith]

very strange... please give me "full" miner stat image. If your miner have problem before, my mod not solve this...

I think it's normal, I have seen a few gears that have some weird target hashrate but as long as the actual hashrate is within normal range then all good, but that doesn't seem to be the case here with 12.5TH assuming his gear is S9k it has to be over 13th for all batches/versions unless he has a few bad chips here and there.

elfarto69 how long has this miner been online for? also, what was the average hashrate on the stock firmware?

[elfarto69]

Miners are supposed to be 13.5 TH/s, and that's more or less what they yield. How is GH Target calculated ?
Here is a screenshot of the stats page:
https://iili.io/d2rEsS.png

[mikeywith]

Why can't you post a complete image of the miner status page? you can hide the pool/worker/wallet details, some information at the top of the page is important.

[thierry4wd]

This miner have a problem ... 0.3HW is BIG !!!

so, don't send full stat, don't help ... is easy ? lol

[elfarto69]

The problem is that the API call that reads the frequency uses  the bitmain-freq value from the config file, in these S9K asics the value is irrelevant if present yet the API returns this value.
Since the UI uses the API call to calculate the hashrate it gets the math wrong. removing it from the config file resolves the issue.

[Keezasa]

So i have tried installing your firmware using SD card. Red and green light LEDs stay on. 20mins later they are still on. No difference. Doing upgrade route from web page gives me Cannot Find Signature!!!

Code:

Miner Type	Antminer S9 SE
Kernel Version	Linux 4.6.0-xilinx-gff8137b-dirty #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
File System Version	Thu Jul 11 09:57:07 CST 2019

Any suggestions?

All I want to do is underclock this PoS.

[BitMaxz]

Do you have any extra SD cards? Maybe your SD card is damaged or an SD card that always corrupted when transferring files.

Try to use a known working SD card and make sure to use this firmware as the guide above and make sure you push the card to the slot properly. If it doesn't work repeat the procedure remove>turn off>insert card>then turn on the miner check the lights if flashing.

[mikeywith]

Since the lights flash constantly i think the sdcard is fine, but maybe the way he puts the files on the sdcard is wrong, the files need to be in the Sdcard directory itself, not in a folder whatsoever, I see a lot of people make this mistake, if files are correctly placed then using another Sdcard is the next best move.

All I want to do is underclock this PoS.

Not sure if this modified firmware will allow you to underclock it, wait for thierry4wd to confirm.

[BitMaxz]

Yeah, in addition, the file above needs to unzip/extract and maybe he just directly put the whole zip file into sd card without extracting the image from SD mptesfirmware T17-S17-S9K-S9SE.zip.

That's why he said "The LEDs stay On" but not flashing it means the files he put are not recognized.


@Keezasa

Make sure to extract the file from the zip file and copy all files from the folder you extracted including the image and paste it to the root of the SD card.

[Keezasa]

Hi Gents,

Thanks for all the help. I have not been home to dabble with S9.

So I tried what you all suggested. Extract files to flash drive. I was using rufus to write the file to the SDcard. Firmware loaded up nice and quick. Reading as S9k. MP TEST FIRMWARE!

Giving it a test drive now and see what it comes up with.

I noticed the fan control option only affects FAN1 and not both of them. FAN2 runs at full speed.

	FAN1	FAN2
Speed (r/min)	3840	5280

[thierry4wd]

Hi, no this works fine on both fans, in reality on almost all minors the 2 fans are different, in fact for the same% one fan will run faster than the other, just try to reverse the connectors of the fan and you will see;) or, for example, apply 30%, and you will also see;)

Thanks for testing my tiny mod

[cryptokayman]

Hi all, i'm happy to share my moded files with all ! Please read all before installing !!!

Feature :

-Stock firmware
-SSH unlocked
-Fan control unlocked
-LPM unlocked (but not working on this miner)
-Statut miner page include my mod for monitoring healt miner


For install :

1 : just try upgrade this ! if not work, jump to "2"
2 : Power off miner
3 : Make all this file on SD card and inser on miner (SD Unlocker 17 Family)    ----- https://www.djayos.com -----
4 : WARNING : this files is taken on T17/S17 firmware, please unplug all data cable on all hashboard before power on miner ! (just for inssurance for save hashboard eprom probably)

5 : power on miner, and wait GREEN and RED led flashing
6 : power off miner and remove sd card
7 : power on miner , and flash my firmware ! ----- ask me -----
8 : If all is ok, power off miner, plug all data cable again, and POWER ON !!!



Enjoy !!!  

If you want donate, do not hesitate !!! lol  

Sorry i am bit late to the party, i couldn't find Your version of S9SE or S9K on your site https://www.djayos.com only S9.S9I.S9J.T9. Have you removed it?