amirheavy666 (OP)
Full Member
Offline
Activity: 228
Merit: 101
NEM (XEM) Top Coin
|
|
July 24, 2020, 11:00:29 AM Last edit: July 24, 2020, 01:29:59 PM by amirheavy666 |
|
Dear bitcointalk membersI have a problem with my new antminer t17+ 55 th/s : My T17+ worked without any problems until one day the power of the farm was cut off and reconnected and after that the device works with only two hashboards with the log on below when i turn on my antminer every time. But when I reset factory my miner with pressing the “reset” button on the miner, the miner works correctly with 3 hashboards but after 4-5 hours without any problem, again miner works with 2 hashboard. what do you thinks of problem? I updated framework to newest version but the problem is exist yet... please check the code on below and advice about this problem... This log :Booting Linux on physical CPU 0x0 Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: Xilinx Zynq cma: Reserved 16 MiB at 0x0e000000 Memory policy: Data cache writealloc On node 0 totalpages: 61440 free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000 Normal zone: 480 pages used for memmap Normal zone: 0 pages reserved Normal zone: 61440 pages, LIFO batch:15 percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152 pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960 Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 203416K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25960K reserved, 16384K cma-reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xcf800000 - 0xff800000 ( 768 MB) lowmem : 0xc0000000 - 0xcf000000 ( 240 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc090c424 (9234 kB) .init : 0xc0a00000 - 0xc0b00000 (1024 kB) .data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB) .bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB) Preemptible hierarchical RCU implementation. Build-time adjustment of leaf fanout to 32. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 NR_IRQS:16 nr_irqs:16 16 efuse mapped to cf800000 ps7-slcr mapped to cf802000 L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 zynq_clock_init: clkc starts at cf802100 Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns ps7-ttc #0 at cf80a000, irq=18 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100058 CPU1: failed to boot: -1 Brought up 1 CPUs SMP: Total of 1 processors activated (666.66 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor menu hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb media: Linux media interface: v0.10 Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered EDAC MC: Ver: 3.0.0 Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 12920K (cce62000 - cdb00000) hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available futex hash table entries: 512 (order: 3, 32768 bytes) workingset: timestamp_bits=28 max_order=16 bucket_order=0 jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps console [ttyPS0] enabled xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000 [drm] Initialized drm 1.1.0 20060810 brd: module loaded loop: module loaded CAN device driver interface gpiod_set_value: invalid GPIO libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00) Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1) e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k e1000e: Copyright(c) 1999 - 2015 Intel Corporation. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice i2c /dev entries driver Xilinx Zynq CpuIdle Driver started sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA ledtrig-cpu: registered to indicate activity on CPUs usbcore: registered new interface driver usbhid usbhid: USB HID core driver nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda nand: Micron MT29F2G08ABAEAWP nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 6 ofpart partitions found on MTD device pl35x-nand Creating 6 MTD partitions on "pl35x-nand": 0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel" 0x000002800000-0x000004800000 : "ramfs" 0x000004800000-0x000005000000 : "configs" 0x000005000000-0x000006000000 : "reserve" 0x000006000000-0x000008000000 : "ramfs-bak" 0x000008000000-0x000010000000 : "reserve1" NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20120528 t) can: netlink gateway (rev 20130117) max_hops=1 zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05' zynq_pm_late_init: Unable to map DDRC IO memory. Registering SWP/SWPB emulation handler hctosys: unable to open rtc device (rtc0) ALSA device list: No soundcards found. RAMDISK: gzip image found at block 0 EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities EXT4-fs (ram0): mounted filesystem without journal. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 1:0. devtmpfs: mounted Freeing unused kernel memory: 1024K (c0a00000 - c0b00000) EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr random: dd urandom read with 0 bits of entropy available ubi0: attaching mtd2 ubi0: scanning is finished ubi0: attached mtd2 (name "configs", size 8 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 34/12, WL threshold: 4096, image sequence number: 262741923 ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40 ubi0: background thread "ubi_bgt0d" started, PID 708 UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711 UBIFS (ubi0:0): recovery needed UBIFS (ubi0:0): recovery completed UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs" UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs) UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID A9E8BDA4-70DE-45D9-83BE-2DD9F129C0C6, small LPT model ubi1: attaching mtd5 ubi1: scanning is finished ubi1: attached mtd5 (name "reserve1", size 128 MiB) ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0 ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi1: max/mean erase counter: 125/26, WL threshold: 4096, image sequence number: 3563076859 ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36 ubi1: background thread "ubi_bgt1d" started, PID 720 UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723 UBIFS (ubi1:0): recovery needed UBIFS (ubi1:0): recovery completed UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1" UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs) UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB) UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID A21581E4-693A-4BBF-A66A-FCE5ACD2EF7F, small LPT model IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz macb e000b000.ethernet eth0: link up (100/Full) IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready In axi fpga driver! request_mem_region OK! AXI fpga dev virtual address is 0xcfb38000 *base_vir_addr = 0xb023 In fpga mem driver! request_mem_region OK! fpga mem virtual address is 0xd2000000 random: nonblocking pool is initialized macb e000b000.ethernet eth0: link down macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz macb e000b000.ethernet eth0: link up (100/Full) 2020-07-24 07:37:33 driver-btm-api.c:762:init_freq_mode: This is scan-user version 2020-07-24 07:37:33 driver-btm-api.c:2553:bitmain_soc_init: opt_multi_version = 1 2020-07-24 07:37:33 driver-btm-api.c:2554:bitmain_soc_init: opt_bitmain_ab = 1 2020-07-24 07:37:33 driver-btm-api.c:2555:bitmain_soc_init: opt_bitmain_work_mode = 0 2020-07-24 07:37:33 driver-btm-api.c:2556:bitmain_soc_init: Miner compile time: Tue Jun 2 10:11:10 CST 2020 type: Antminer T17+ 2020-07-24 07:37:33 driver-btm-api.c:2557:bitmain_soc_init: commit version: 9e9a5bf 2020-06-01 18:48:14, build by: lol 2020-06-02 10:21:50 2020-07-24 07:37:33 driver-btm-api.c:2180:show_sn: 807c250c2b10481c� 7 2020-07-24 07:37:33 driver-btm-api.c:2237:handle_sn_for_factory_mode: read sn success, 807c250c2b10481c� 7 2020-07-24 07:37:33 fan.c:263:front_fan_power_on: Note: front fan is power on! 2020-07-24 07:37:33 fan.c:273:rear_fan_power_on: Note: rear fan is power on! 2020-07-24 07:37:33 driver-btm-api.c:1357:miner_device_init: Detect 256MB control board of XILINX 2020-07-24 07:37:33 driver-btm-api.c:1298:init_fan_parameter: fan_eft : 0 fan_pwm : 0 2020-07-24 07:37:39 driver-btm-api.c:1281:init_miner_version: miner ID : 807c250c2b10481c 2020-07-24 07:37:39 driver-btm-api.c:1287:init_miner_version: FPGA Version = 0xB023 2020-07-24 07:37:45 driver-btm-api.c:814:get_product_id: product_id[0] = 0 2020-07-24 07:37:45 driver-btm-api.c:814:get_product_id: product_id[1] = 0 2020-07-24 07:37:45 driver-btm-api.c:814:get_product_id: product_id[2] = 0 2020-07-24 07:37:45 driver-btm-api.c:845:get_chip_version: chip_version[0] = 1 2020-07-24 07:37:45 driver-btm-api.c:845:get_chip_version: chip_version[1] = 1 2020-07-24 07:37:45 driver-btm-api.c:845:get_chip_version: chip_version[2] = 1 2020-07-24 07:37:45 driver-btm-api.c:2293:update_conf_by_power_feedback: Power feedback is disabled 2020-07-24 07:37:45 driver-btm-api.c:2297:update_conf_by_power_feedback: get_calibration_voltage, vol:1850. 2020-07-24 07:37:45 frequency.c:1389:adjust_higer_max_vol_table: adjust_higer_max_vol_table, ideal_hashrate = 56943, index = 2, adjust_vol = 40 2020-07-24 07:37:45 thread.c:1462:create_read_nonce_reg_thread: create thread 2020-07-24 07:37:51 driver-btm-api.c:1281:init_miner_version: miner ID : 807c250c2b10481c 2020-07-24 07:37:51 driver-btm-api.c:1287:init_miner_version: FPGA Version = 0xB023 2020-07-24 07:37:56 driver-btm-api.c:814:get_product_id: product_id[0] = 0 2020-07-24 07:37:56 driver-btm-api.c:814:get_product_id: product_id[1] = 0 2020-07-24 07:37:56 driver-btm-api.c:814:get_product_id: product_id[2] = 0 2020-07-24 07:37:56 driver-btm-api.c:845:get_chip_version: chip_version[0] = 1 2020-07-24 07:37:56 driver-btm-api.c:845:get_chip_version: chip_version[1] = 1 2020-07-24 07:37:56 driver-btm-api.c:845:get_chip_version: chip_version[2] = 1 2020-07-24 07:37:56 driver-btm-api.c:1944:get_ccdly_opt: ccdly_opt[0] = 0 2020-07-24 07:37:56 driver-btm-api.c:1944:get_ccdly_opt: ccdly_opt[1] = 0 2020-07-24 07:37:56 driver-btm-api.c:1944:get_ccdly_opt: ccdly_opt[2] = 0 2020-07-24 07:37:56 driver-btm-api.c:2439:bitmain_board_init: g_ccdly_opt = 0 2020-07-24 07:37:56 driver-btm-api.c:775:_set_project_type: project:0, set to T17Plus always 2020-07-24 07:37:56 driver-btm-api.c:790:_set_project_type: Project type: Antminer T17+ 2020-07-24 07:37:56 driver-btm-api.c:801:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100 2020-07-24 07:37:56 driver-btm-api.c:802:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100 2020-07-24 07:37:56 driver-btm-api.c:801:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100 2020-07-24 07:37:56 driver-btm-api.c:802:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100 2020-07-24 07:37:56 driver-btm-api.c:801:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100 2020-07-24 07:37:56 driver-btm-api.c:802:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100 2020-07-24 07:37:56 driver-btm-api.c:2461:bitmain_board_init: Fan check passed. 2020-07-24 07:37:57 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app 2020-07-24 07:37:59 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0x88 2020-07-24 07:38:00 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app 2020-07-24 07:38:02 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88 2020-07-24 07:38:03 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app 2020-07-24 07:38:05 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88 2020-07-24 07:38:05 thread.c:1457:create_pic_heart_beat_thread: create thread 2020-07-24 07:38:07 power_api.c:231:power_init: power type version: 0x0042 2020-07-24 07:38:07 power_api.c:249:power_init: Power init: 2020-07-24 07:38:07 power_api.c:250:power_init: current_voltage_raw = 0 2020-07-24 07:38:07 power_api.c:251:power_init: highest_voltage_raw = 1950 2020-07-24 07:38:07 power_api.c:252:power_init: working_voltage_raw = 1900 2020-07-24 07:38:07 power_api.c:253:power_init: higher_voltage_raw = 1930 2020-07-24 07:38:07 power_api.c:254:power_init: check_asic_voltage_raw = 2000 2020-07-24 07:38:07 driver-btm-api.c:2471:bitmain_board_init: Enter 30s sleep to make sure power release finish. 2020-07-24 07:38:07 power_api.c:221:power_off: set gpio907 to 1 2020-07-24 07:38:38 power_api.c:206:power_on: set gpio907 to 0 2020-07-24 07:38:39 power_api.c:388:set_to_voltage_by_steps: Set to voltage raw 1850, step by step. 2020-07-24 07:38:57 power_api.c:120:check_voltage_multi: retry time: 0 2020-07-24 07:38:58 power_api.c:56:_get_avg_voltage: an6 raw = 2.522581, factor = 1.009032 2020-07-24 07:38:58 power_api.c:60:_get_avg_voltage: chain 0, an0 = 0.631714, an2 18.708440, an6 2.500000. 2020-07-24 07:38:59 power_api.c:56:_get_avg_voltage: an6 raw = 2.525806, factor = 1.010323 2020-07-24 07:38:59 power_api.c:60:_get_avg_voltage: chain 1, an0 = 0.679438, an2 18.660282, an6 2.500000. 2020-07-24 07:39:00 power_api.c:56:_get_avg_voltage: an6 raw = 2.522581, factor = 1.009032 2020-07-24 07:39:00 power_api.c:60:_get_avg_voltage: chain 2, an0 = 0.558824, an2 18.732737, an6 2.500000. 2020-07-24 07:39:00 power_api.c:85:_get_avg_voltage: average_voltage = 18.700486 2020-07-24 07:39:00 power_api.c:106:check_voltage: target_vol = 18.50, actural_vol = 18.70, check voltage passed. 2020-07-24 07:39:03 power_api.c:56:_get_avg_voltage: an6 raw = 2.522581, factor = 1.009032 2020-07-24 07:39:03 power_api.c:60:_get_avg_voltage: chain 0, an0 = 0.631714, an2 18.684143, an6 2.500000. 2020-07-24 07:39:04 power_api.c:56:_get_avg_voltage: an6 raw = 2.525806, factor = 1.010323 2020-07-24 07:39:04 power_api.c:60:_get_avg_voltage: chain 1, an0 = 0.655172, an2 18.660282, an6 2.500000. 2020-07-24 07:39:05 power_api.c:56:_get_avg_voltage: an6 raw = 2.522581, factor = 1.009032 2020-07-24 07:39:05 power_api.c:60:_get_avg_voltage: chain 2, an0 = 0.558824, an2 18.708440, an6 2.500000. 2020-07-24 07:39:05 power_api.c:85:_get_avg_voltage: average_voltage = 18.684288 2020-07-24 07:39:05 power_api.c:106:check_voltage: target_vol = 18.50, actural_vol = 18.68, check voltage passed. 2020-07-24 07:39:05 uart.c:81:set_baud: set fpga_baud = 115200, fpga_divider = 26 2020-07-24 07:39:14 driver-btm-api.c:1162:check_asic_number_with_power_on: Chain[0]: find 44 asic, times 0 2020-07-24 07:39:23 driver-btm-api.c:1162:check_asic_number_with_power_on: Chain[1]: find 44 asic, times 0 2020-07-24 07:39:31 driver-btm-api.c:1162:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 0 2020-07-24 07:39:40 driver-btm-api.c:1163:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 1 2020-07-24 07:39:51 driver-btm-api.c:1164:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 2 2020-07-24 07:39:51 power_api.c:400:set_to_check_asic_voltage_by_steps: Set to voltage raw 2000, step by step. 2020-07-24 07:40:07 power_api.c:120:check_voltage_multi: retry time: 0 2020-07-24 07:40:08 power_api.c:56:_get_avg_voltage: an6 raw = 2.525806, factor = 1.010323 2020-07-24 07:40:08 power_api.c:60:_get_avg_voltage: chain 0, an0 = 20.164752, an2 20.140487, an6 2.500000. 2020-07-24 07:40:09 power_api.c:56:_get_avg_voltage: an6 raw = 2.529032, factor = 1.011613 2020-07-24 07:40:09 power_api.c:60:_get_avg_voltage: chain 1, an0 = 20.090561, an2 20.090561, an6 2.500000. 2020-07-24 07:40:10 power_api.c:56:_get_avg_voltage: an6 raw = 2.522581, factor = 1.009032 2020-07-24 07:40:10 power_api.c:60:_get_avg_voltage: chain 2, an0 = 0.558824, an2 20.166241, an6 2.500000. 2020-07-24 07:40:10 power_api.c:85:_get_avg_voltage: average_voltage = 20.132429 2020-07-24 07:40:10 power_api.c:106:check_voltage: target_vol = 20.00, actural_vol = 20.13, check voltage passed. 2020-07-24 07:40:12 power_api.c:56:_get_avg_voltage: an6 raw = 2.525806, factor = 1.010323 2020-07-24 07:40:12 power_api.c:60:_get_avg_voltage: chain 0, an0 = 20.164752, an2 20.140487, an6 2.500000. 2020-07-24 07:40:13 power_api.c:56:_get_avg_voltage: an6 raw = 2.529032, factor = 1.011613 2020-07-24 07:40:13 power_api.c:60:_get_avg_voltage: chain 1, an0 = 20.090561, an2 20.090561, an6 2.500000. 2020-07-24 07:40:14 power_api.c:56:_get_avg_voltage: an6 raw = 2.522581, factor = 1.009032 2020-07-24 07:40:14 power_api.c:60:_get_avg_voltage: chain 2, an0 = 0.558824, an2 20.166241, an6 2.500000. 2020-07-24 07:40:14 power_api.c:85:_get_avg_voltage: average_voltage = 20.132429 2020-07-24 07:40:14 power_api.c:106:check_voltage: target_vol = 20.00, actural_vol = 20.13, check voltage passed. 2020-07-24 07:40:23 driver-btm-api.c:1167:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 3 2020-07-24 07:40:34 driver-btm-api.c:1168:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 4 chain 2, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff 2020-07-24 07:40:43 driver-btm-api.c:1169:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 5 chain 2, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff 2020-07-24 07:40:51 driver-btm-api.c:1170:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 6 2020-07-24 07:40:51 driver-btm-api.c:1235:check_asic_number: Chain 2 only find 0 asic, will power off hash board 2 2020-07-24 07:40:52 driver-btm-api.c:1238:check_asic_number: Chain 2 voltage: an0 = 20.274838, an2 20.348387, an6 2.525806. 2020-07-24 07:40:57 driver-btm-api.c:425:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1 2020-07-24 07:40:57 driver-btm-api.c:425:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1 2020-07-24 07:40:57 driver-btm-api.c:1931:get_core_clock_delay_setting: PWTH_SEL 3, CCDLY_SEL 0 2020-07-24 07:40:57 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34 2020-07-24 07:40:57 driver-btm-api.c:1972:check_clock_counter: freq 50 clock_counter_limit 6 2020-07-24 07:41:12 voltage[0] = 1790 2020-07-24 07:41:12 voltage[1] = 1790 2020-07-24 07:41:12 power_api.c:262:set_working_voltage_raw: working_voltage_raw = 1790 2020-07-24 07:41:14 temperature.c:313:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success. NCT218 2020-07-24 07:41:15 temperature.c:313:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success. NCT218 2020-07-24 07:41:15 uart.c:81:set_baud: set fpga_baud = 6000000, fpga_divider = 3 2020-07-24 07:41:16 driver-btm-api.c:294:check_bringup_temp: Bring up temperature is 24 2020-07-24 07:41:16 thread.c:1477:create_check_miner_status_thread: create thread 2020-07-24 07:41:16 thread.c:1467:create_set_miner_status_thread: create thread 2020-07-24 07:41:16 driver-btm-api.c:712:calculate_timeout: dev->timeout = 245 2020-07-24 07:41:16 thread.c:1447:create_temperature_monitor_thread: create thread 2020-07-24 07:41:16 frequency.c:527:check_bringup_temp_dec_freq: dec freq = 0 when bringup temp = 24 dec_freq_index=0 2020-07-24 07:41:16 freq_tuning.c:184:freq_tuning_get_max_freq: Max freq of tuning is 790 2020-07-24 07:41:16 driver-btm-api.c:1802:send_null_work: [DEBUG] Send null work. 2020-07-24 07:41:16 thread.c:1437:create_asic_status_monitor_thread: create thread 2020-07-24 07:41:16 frequency.c:1194:inc_freq_with_fixed_vco: chain = 255, freq = 625, is_higher_voltage = true 2020-07-24 07:41:16 frequency.c:1210:inc_freq_with_fixed_vco: [0] _POSTDIV1 = 7, _POSTDIV2 = 7, USER_DIV = 1, freq = 51 2020-07-24 07:41:16 power_api.c:388:set_to_voltage_by_steps: Set to voltage raw 1880, step by step. 2020-07-24 07:41:33 power_api.c:120:check_voltage_multi: retry time: 0 2020-07-24 07:41:35 power_api.c:56:_get_avg_voltage: an6 raw = 2.525806, factor = 1.010323 2020-07-24 07:41:35 power_api.c:60:_get_avg_voltage: chain 0, an0 = 19.000001, an2 18.951470, an6 2.500000. 2020-07-24 07:41:36 power_api.c:56:_get_avg_voltage: an6 raw = 2.529032, factor = 1.011613 2020-07-24 07:41:36 power_api.c:60:_get_avg_voltage: chain 1, an0 = 18.903061, an2 18.927296, an6 2.500000. 2020-07-24 07:41:36 power_api.c:85:_get_avg_voltage: average_voltage = 18.939383 2020-07-24 07:41:36 power_api.c:106:check_voltage: target_vol = 18.80, actural_vol = 18.94, check voltage passed. 2020-07-24 07:41:38 power_api.c:56:_get_avg_voltage: an6 raw = 2.525806, factor = 1.010323 2020-07-24 07:41:38 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.975736, an2 18.951470, an6 2.500000. 2020-07-24 07:41:39 power_api.c:56:_get_avg_voltage: an6 raw = 2.529032, factor = 1.011613 2020-07-24 07:41:39 power_api.c:60:_get_avg_voltage: chain 1, an0 = 18.927296, an2 18.927296, an6 2.500000. 2020-07-24 07:41:39 power_api.c:85:_get_avg_voltage: average_voltage = 18.939383 2020-07-24 07:41:39 power_api.c:106:check_voltage: target_vol = 18.80, actural_vol = 18.94, check voltage passed. 2020-07-24 07:41:41 frequency.c:1210:inc_freq_with_fixed_vco: [1] _POSTDIV1 = 7, _POSTDIV2 = 6, USER_DIV = 1, freq = 59 2020-07-24 07:41:43 frequency.c:1210:inc_freq_with_fixed_vco: [2] _POSTDIV1 = 6, _POSTDIV2 = 6, USER_DIV = 1, freq = 69 2020-07-24 07:41:45 frequency.c:1210:inc_freq_with_fixed_vco: [3] _POSTDIV1 = 7, _POSTDIV2 = 5, USER_DIV = 1, freq = 71 2020-07-24 07:41:47 frequency.c:1210:inc_freq_with_fixed_vco: [4] _POSTDIV1 = 6, _POSTDIV2 = 5, USER_DIV = 1, freq = 83 2020-07-24 07:41:49 frequency.c:1210:inc_freq_with_fixed_vco: [5] _POSTDIV1 = 7, _POSTDIV2 = 4, USER_DIV = 1, freq = 89 2020-07-24 07:41:51 frequency.c:1210:inc_freq_with_fixed_vco: [6] _POSTDIV1 = 5, _POSTDIV2 = 5, USER_DIV = 1, freq = 100 2020-07-24 07:41:56 frequency.c:1210:inc_freq_with_fixed_vco: [7] _POSTDIV1 = 6, _POSTDIV2 = 4, USER_DIV = 1, freq = 104 2020-07-24 07:42:00 frequency.c:1210:inc_freq_with_fixed_vco: [8] _POSTDIV1 = 7, _POSTDIV2 = 3, USER_DIV = 1, freq = 119 2020-07-24 07:42:05 frequency.c:1210:inc_freq_with_fixed_vco: [9] _POSTDIV1 = 5, _POSTDIV2 = 4, USER_DIV = 1, freq = 125 2020-07-24 07:42:09 frequency.c:1210:inc_freq_with_fixed_vco: [10] _POSTDIV1 = 6, _POSTDIV2 = 3, USER_DIV = 1, freq = 138 2020-07-24 07:42:14 frequency.c:1210:inc_freq_with_fixed_vco: [11] _POSTDIV1 = 4, _POSTDIV2 = 4, USER_DIV = 1, freq = 156 2020-07-24 07:42:22 frequency.c:1210:inc_freq_with_fixed_vco: [12] _POSTDIV1 = 5, _POSTDIV2 = 3, USER_DIV = 1, freq = 166 2020-07-24 07:42:30 frequency.c:1210:inc_freq_with_fixed_vco: [13] _POSTDIV1 = 7, _POSTDIV2 = 2, USER_DIV = 1, freq = 178 2020-07-24 07:42:38 frequency.c:1210:inc_freq_with_fixed_vco: [14] _POSTDIV1 = 4, _POSTDIV2 = 3, USER_DIV = 1, freq = 208 2020-07-24 07:42:50 frequency.c:1210:inc_freq_with_fixed_vco: [15] _POSTDIV1 = 6, _POSTDIV2 = 2, USER_DIV = 1, freq = 208 2020-07-24 07:43:03 frequency.c:1210:inc_freq_with_fixed_vco: [16] _POSTDIV1 = 5, _POSTDIV2 = 2, USER_DIV = 1, freq = 250 2020-07-24 07:43:21 frequency.c:1210:inc_freq_with_fixed_vco: [17] _POSTDIV1 = 4, _POSTDIV2 = 2, USER_DIV = 1, freq = 312 2020-07-24 07:43:45 frequency.c:1210:inc_freq_with_fixed_vco: [18] _POSTDIV1 = 7, _POSTDIV2 = 1, USER_DIV = 1, freq = 357 2020-07-24 07:44:17 frequency.c:1210:inc_freq_with_fixed_vco: [19] _POSTDIV1 = 6, _POSTDIV2 = 1, USER_DIV = 1, freq = 416 2020-07-24 07:44:58 frequency.c:1210:inc_freq_with_fixed_vco: [20] _POSTDIV1 = 5, _POSTDIV2 = 1, USER_DIV = 1, freq = 500 2020-07-24 07:44:58 power_api.c:388:set_to_voltage_by_steps: Set to voltage raw 1860, step by step. 2020-07-24 07:45:15 power_api.c:120:check_voltage_multi: retry time: 0 2020-07-24 07:45:16 power_api.c:56:_get_avg_voltage: an6 raw = 2.525806, factor = 1.010323 2020-07-24 07:45:16 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.757345, an2 18.733079, an6 2.500000. 2020-07-24 07:45:18 power_api.c:56:_get_avg_voltage: an6 raw = 2.532258, factor = 1.012903 2020-07-24 07:45:18 power_api.c:60:_get_avg_voltage: chain 1, an0 = 18.685351, an2 18.685351, an6 2.500000. 2020-07-24 07:45:18 power_api.c:85:_get_avg_voltage: average_voltage = 18.709215 2020-07-24 07:45:18 power_api.c:106:check_voltage: target_vol = 18.60, actural_vol = 18.71, check voltage passed. 2020-07-24 07:45:20 power_api.c:56:_get_avg_voltage: an6 raw = 2.525806, factor = 1.010323 2020-07-24 07:45:20 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.757345, an2 18.733079, an6 2.500000. 2020-07-24 07:45:21 power_api.c:56:_get_avg_voltage: an6 raw = 2.532258, factor = 1.012903 2020-07-24 07:45:21 power_api.c:60:_get_avg_voltage: chain 1, an0 = 18.685351, an2 18.709555, an6 2.500000. 2020-07-24 07:45:21 power_api.c:85:_get_avg_voltage: average_voltage = 18.721317 2020-07-24 07:45:21 power_api.c:106:check_voltage: target_vol = 18.60, actural_vol = 18.72, check voltage passed. 2020-07-24 07:47:22 frequency.c:1210:inc_freq_with_fixed_vco: [21] _POSTDIV1 = 4, _POSTDIV2 = 1, USER_DIV = 1, freq = 625 2020-07-24 07:47:22 power_api.c:388:set_to_voltage_by_steps: Set to voltage raw 1840, step by step. 2020-07-24 07:47:39 power_api.c:120:check_voltage_multi: retry time: 0 2020-07-24 07:47:40 power_api.c:56:_get_avg_voltage: an6 raw = 2.529032, factor = 1.011613 2020-07-24 07:47:40 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.515306, an2 18.515306, an6 2.500000. 2020-07-24 07:47:41 power_api.c:56:_get_avg_voltage: an6 raw = 2.532258, factor = 1.012903 2020-07-24 07:47:41 power_api.c:60:_get_avg_voltage: chain 1, an0 = 18.443313, an2 18.467517, an6 2.500000. 2020-07-24 07:47:41 power_api.c:85:_get_avg_voltage: average_voltage = 18.491411 2020-07-24 07:47:41 power_api.c:106:check_voltage: target_vol = 18.40, actural_vol = 18.49, check voltage passed. 2020-07-24 07:47:43 power_api.c:56:_get_avg_voltage: an6 raw = 2.529032, factor = 1.011613 2020-07-24 07:47:43 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.515306, an2 18.491071, an6 2.500000. 2020-07-24 07:47:44 power_api.c:56:_get_avg_voltage: an6 raw = 2.532258, factor = 1.012903 2020-07-24 07:47:44 power_api.c:60:_get_avg_voltage: chain 1, an0 = 18.443313, an2 18.467517, an6 2.500000. 2020-07-24 07:47:44 power_api.c:85:_get_avg_voltage: average_voltage = 18.479294 2020-07-24 07:47:44 power_api.c:106:check_voltage: target_vol = 18.40, actural_vol = 18.48, check voltage passed. 2020-07-24 07:50:33 frequency.c:1231:inc_freq_with_fixed_step: chain = 0, freq_start = 625, freq_end = 640, freq_step = 5, is_higher_voltage = true 2020-07-24 07:50:33 driver-btm-api.c:2020:check_clock_counter_domain_last_core: freq 630 clock_counter_limit 20 2020-07-24 07:50:35 driver-btm-api.c:2020:check_clock_counter_domain_last_core: freq 635 clock_counter_limit 20 2020-07-24 07:50:37 driver-btm-api.c:2020:check_clock_counter_domain_last_core: freq 640 clock_counter_limit 20 2020-07-24 07:50:38 power_api.c:388:set_to_voltage_by_steps: Set to voltage raw 1830, step by step. 2020-07-24 07:50:55 power_api.c:120:check_voltage_multi: retry time: 0 2020-07-24 07:50:56 power_api.c:56:_get_avg_voltage: an6 raw = 2.525806, factor = 1.010323 2020-07-24 07:50:56 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.441891, an2 18.441891, an6 2.500000. 2020-07-24 07:50:58 power_api.c:56:_get_avg_voltage: an6 raw = 2.535484, factor = 1.014194 2020-07-24 07:50:58 power_api.c:60:_get_avg_voltage: chain 1, an0 = 18.347328, an2 18.347328, an6 2.500000. 2020-07-24 07:50:58 power_api.c:85:_get_avg_voltage: average_voltage = 18.394609 2020-07-24 07:50:58 power_api.c:106:check_voltage: target_vol = 18.30, actural_vol = 18.39, check voltage passed. 2020-07-24 07:51:00 power_api.c:56:_get_avg_voltage: an6 raw = 2.529032, factor = 1.011613 2020-07-24 07:51:00 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.418367, an2 18.418367, an6 2.500000. 2020-07-24 07:51:01 power_api.c:56:_get_avg_voltage: an6 raw = 2.532258, factor = 1.012903 2020-07-24 07:51:01 power_api.c:60:_get_avg_voltage: chain 1, an0 = 18.370702, an2 18.370702, an6 2.500000. 2020-07-24 07:51:01 power_api.c:85:_get_avg_voltage: average_voltage = 18.394534 2020-07-24 07:51:01 power_api.c:106:check_voltage: target_vol = 18.30, actural_vol = 18.39, check voltage passed. 2020-07-24 07:51:01 frequency.c:1058:inc_asic_diff_freq_by_steps: chain = 0, start = 640, freq_step = 5 2020-07-24 07:51:03 frequency.c:1058:inc_asic_diff_freq_by_steps: chain = 1, start = 625, freq_step = 5 2020-07-24 07:51:05 driver-btm-api.c:743:set_timeout: freq 660 final timeout=111 2020-07-24 07:51:05 power_api.c:346:set_to_working_voltage_by_steps: Set to voltage raw 1790, step by step. 2020-07-24 07:51:22 power_api.c:120:check_voltage_multi: retry time: 0 2020-07-24 07:51:23 power_api.c:56:_get_avg_voltage: an6 raw = 2.529032, factor = 1.011613 2020-07-24 07:51:23 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.054847, an2 18.030612, an6 2.500000. 2020-07-24 07:51:24 power_api.c:56:_get_avg_voltage: an6 raw = 2.532258, factor = 1.012903 2020-07-24 07:51:24 power_api.c:60:_get_avg_voltage: chain 1, an0 = 17.983440, an2 18.007644, an6 2.500000. 2020-07-24 07:51:24 power_api.c:85:_get_avg_voltage: average_voltage = 18.019128 2020-07-24 07:51:24 power_api.c:106:check_voltage: target_vol = 17.90, actural_vol = 18.02, check voltage passed. 2020-07-24 07:51:26 power_api.c:56:_get_avg_voltage: an6 raw = 2.529032, factor = 1.011613 2020-07-24 07:51:26 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.030612, an2 18.030612, an6 2.500000. 2020-07-24 07:51:27 power_api.c:56:_get_avg_voltage: an6 raw = 2.532258, factor = 1.012903 2020-07-24 07:51:27 power_api.c:60:_get_avg_voltage: chain 1, an0 = 17.983440, an2 18.007644, an6 2.500000. 2020-07-24 07:51:27 power_api.c:85:_get_avg_voltage: average_voltage = 18.019128 2020-07-24 07:51:27 power_api.c:106:check_voltage: target_vol = 17.90, actural_vol = 18.02, check voltage passed. 2020-07-24 07:51:27 thread.c:1472:create_check_system_status_thread: create thread 2020-07-24 07:51:27 driver-btm-api.c:2758:bitmain_soc_init: Init done! 2020-07-24 07:51:27 driver-btm-api.c:222:set_miner_status: STATUS_INIT 2020-07-24 07:51:32 driver-btm-api.c:222:set_miner_status: STATUS_OKAY 2020-07-24 07:51:33 frequency.c:316:get_sale_hash_rate_GH: g_sale_hash_rate = 34704 2020-07-24 07:51:37 driver-btm-api.c:1539:dhash_chip_send_job: Version num 4. 2020-07-24 07:51:37 driver-btm-api.c:1686:dhash_chip_send_job: stime.tv_sec 1595577097, block_ntime 1595577095 2020-07-24 07:51:37 driver-btm-api.c:1539:dhash_chip_send_job: Version num 1. 2020-07-24 07:52:01 driver-btm-api.c:1539:dhash_chip_send_job: Version num 4.
|