Pool Change

[solidserver]

Hi, I also have a problem with a T2T innosilicon, I want to change the pool and it doesn't change where the problem could be ??

[BitMaxz]

This is not the right place for this issue you must move this to "Mining Support" you can find the move button at the bottom left of this thread.

Anyway, about your problem can you check if there is IPset button can you hold it for 4-15 seconds. It can reset the miner to default to erase the old configuration. If not working try to use this InnoMonitor tool  you can find it from here https://www.innosilicon.com/html/support_en/tool.html.

Then reset it to the factory settings as the image shown below.



And then set the pool using that tool.

Hope it will work.

[solidserver]

Hi, this problem appears


Operation succeedes  1 miner with pool locking

[mikeywith]

I have never owned this gear, but based on your explanation this seems like an infected miner, did you just buy this miner from the second hand market in China or elsewhere from someone you don't trust?

I could be wrong, but you should isolate this miner from other miners until the problem is fixed (better safe than sorry), for now you should try to reset the miner, also if an Sdcard flash is possible it must be done.

[solidserver]

Hi buy from china is used

[mikeywith]

Hi buy from china is used

Well, then that is bad news.

Your chances to recover this gear depend on the type of virus and how innosilicon handles the reset stuff, does the control board have a slot of an sd/tf card? if yes then you can probably find the files needed to flash the miner, or simply requested it from their support team, if it doesn't have an sd card slot then you will have to buy a new control board.

Again, I am not 100%, if it was an Antminer I would be confident because I have seen a truckload of those gears, but I have no idea about this T2T, I assume they use a similar firmware and the are subject to being hacked just like all other mining gears, and the first symptom of an infected miner is the inability to change the pool/worker and this is what I based my conclusion on.

[solidserver]

Hi, I'm a sd card

[mikeywith]

Hi, I'm a sd card

Ok then go ahead and flash it with an sdcard, make sure you test the sdcard before flashing see if it can read/write files, also make sure you download the files that fit your miner's model, and whatever you do, do NOT power the miner off while flashing it.

[solidserver]

i don't know which to download care is?

T2T 25 TH

[mikeywith]

i don't know which to download care is?

T2T 25 TH

I don't know either, here is the guide on how to flash your miner using Sdcard > http://www.innosilicon.com.cn/download/TF-card-firmware-update-manual-en.pdf

But I couldn't find the files for you, their website is pretty useless, I think your best shot would be sending them a support ticket requesting the image file for your miner, make sure you send them the control board model and miner's SN, they should be able to provide you with the correct file, also there is a chance one of the members here have it, perhaps you should start a new topic "Inno T2T sdcard files needed" or something like that, the current title is pretty inaccurate.

[solidserver]

As far as I think, this is not it


G19_R1.2

[BitMaxz]

Try to access the miner on the browser and then find the system overview make a screenshot so that we can see the exact model and hardware version of your miner.

Sample:

http://www.innosilicon.com.cn/statics/images/web_version_dm.png
http://www.innosilicon.com.cn/statics/images/A5/g9diff.jpg

Then for TF/SD card manual, you can read this PDF file http://www.innosilicon.com.cn/download/TF-card-firmware-update-manual-en.pdf

Make sure to check the board first if what is the exact model of your control board.

After flashing this with TF/SD card you can manually upgrade it to the latest firmware available on their support. Never tested this so this is risky because I can't find the right procedure to flash this miner with SD card.

[solidserver]

Type
T2T
Controller Version
soc
MAC Address
50:6c:be:0b:56:8e
Build Date
11th of June 2020 03:28 PM
Platform Version
t2t_soc_20200611_152800

[mikeywith]

Type
T2T
Controller Version
soc

Based on the image posted above the control board type should appear next to "HW Version" which doesn't seem to be the case for your miner, the virus is likely hiding this information, at this point your ONLY option is to contact Inno, they should be able to obtain all the information about your miner and send you the right files for sd flash as well as the firmware you should upload afterward.

[BitMaxz]

If you can disassemble the unit you can check the control board you can see something like this image below.



If you see some text write them down and use that text to search the exact SD card img file for your miner. Use that term in Google with "SD/TF card firmware" at the end of the text. Let see if you can find exact SD card firmware for your miner.

If not, the only best solution is to contact the innosilicon support as suggested above. They can help you out about this problem if it's still under warranty but if not, just try to contact them for SD card image.

[Difidifi]

I had the exact same problem, buying a miner from Innosilicon. In my case it was the T3+. I tried everything, inclusing firmware update, flashing the firmware via TF card, you name it.
The solution was easy, provided by the customer support of Innosilicon, after constantly bugging them for over 5 days: they emailed me an UNLOCK firmware.
The download link is in the description of the video: https://youtu.be/vaj_gymDUHQ

[infini13]

hi.i have your problem and its killing me. if you fine anyway to remove it can you please please please tell me.

[NotFuzzyWarm]

hi.i have your problem and its killing me. if you fine anyway to remove it can you please please please tell me.

Did you even try to look at other topics in this section of the Forum?
Just a few lines down from the top you will find the the existing topic with the solution to the used Innosilicon miners kerfuffle https://bitcointalk.org/index.php?topic=5355134.msg58141121#msg58141121