ckoeber101 (OP)
Newbie
 Offline
Activity: 1
Merit: 0
|
 |
October 03, 2020, 07:19:28 AM
Last edit: October 04, 2020, 12:15:16 AM by frodocooper |
|
Hello, Troubleshooting 2 separate AntMiner T9+ that displays red fault light and no pool connection. The kernel log is practically identical between the AntMiners and shown below, not sure what the issue is. Also upgraded to latest firmware but the problem persists. Thank you for your time. System OverviewMiner Type Antminer T9+
Hostname antMiner
Model GNU/Linux
Hardware Version
Kernel Version Linux 3.14.0-xilinx-g16220c3 #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
File System Version Wed Jul 31 16:20:36 CST 2019
Logic Version V3.57
BMminer Version
Uptime 17
Load Average 0.00, 0.03, 0.04
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06da8ac (6987 kB)
[ 0.000000] .init : 0xc06db000 - 0xc070e380 ( 205 kB)
[ 0.000000] .data : 0xc0710000 - 0xc0757138 ( 285 kB)
[ 0.000000] .bss : 0xc0757144 - 0xc0797bfc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000292] ps7-ttc #0 at df804000, irq=43
[ 0.000590] Console: colour dummy device 80x30
[ 0.000621] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[ 0.090240] pid_max: default: 32768 minimum: 301
[ 0.090451] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090472] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092626] CPU: Testing write buffer coherency: ok
[ 0.092936] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.092992] Setting up static identity map for 0x4cb118 - 0x4cb170
[ 0.093211] L310 cache controller enabled
[ 0.093231] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.170985] CPU1: Booted secondary processor
[ 0.260218] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.260348] Brought up 2 CPUs
[ 0.260367] SMP: Total of 2 processors activated.
[ 0.260375] CPU: All CPU(s) started in SVC mode.
[ 0.261031] devtmpfs: initialized
[ 0.263453] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.264644] regulator-dummy: no parameters
[ 0.271993] NET: Registered protocol family 16
[ 0.274260] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.276524] cpuidle: using governor ladder
[ 0.276537] cpuidle: using governor menu
[ 0.283861] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.285380] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.285394] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.285504] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.307129] bio: create slab <bio-0> at 0
[ 0.308512] vgaarb: loaded
[ 0.309204] SCSI subsystem initialized
[ 0.310105] usbcore: registered new interface driver usbfs
[ 0.310323] usbcore: registered new interface driver hub
[ 0.310559] usbcore: registered new device driver usb
[ 0.311094] media: Linux media interface: v0.10
[ 0.311259] Linux video capture interface: v2.00
[ 0.311504] pps_core: LinuxPPS API ver. 1 registered
[ 0.311516] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.311636] PTP clock support registered
[ 0.311995] EDAC MC: Ver: 3.0.0
[ 0.313180] Advanced Linux Sound Architecture Driver Initialized.
[ 0.315913] DMA-API: preallocated 4096 debug entries
[ 0.315926] DMA-API: debugging enabled by kernel config
[ 0.315995] Switched to clocksource arm_global_timer
[ 0.336734] NET: Registered protocol family 2
[ 0.337382] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.337438] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.337524] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.337568] TCP: reno registered
[ 0.337585] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.337616] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.337842] NET: Registered protocol family 1
[ 0.338175] RPC: Registered named UNIX socket transport module.
[ 0.338188] RPC: Registered udp transport module.
[ 0.338196] RPC: Registered tcp transport module.
[ 0.338205] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.338217] PCI: CLS 0 bytes, default 64
[ 0.338636] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.340619] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.342666] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.342857] msgmni has been set to 967
[ 0.343613] io scheduler noop registered
[ 0.343626] io scheduler deadline registered
[ 0.343666] io scheduler cfq registered (default)
[ 0.355175] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.355195] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.478345] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.045069] console [ttyPS0] enabled
[ 1.049329] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.056964] [drm] Initialized drm 1.1.0 20060810
[ 1.073875] brd: module loaded
[ 1.083228] loop: module loaded
[ 1.092599] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.098384] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.106339] libphy: XEMACPS mii bus: probed
[ 1.110710] ------------- phy_id = 0x3625e62
[ 1.115412] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.124109] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.130789] ehci-pci: EHCI PCI platform driver
[ 1.138033] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.144839] usbcore: registered new interface driver usb-storage
[ 1.151716] mousedev: PS/2 mouse device common for all mice
[ 1.157831] i2c /dev entries driver
[ 1.164711] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.170232] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.176124] Xilinx Zynq CpuIdle Driver started
[ 1.180969] sdhci: Secure Digital Host Controller Interface driver
[ 1.187115] sdhci: Copyright(c) Pierre Ossman
[ 1.191407] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.198282] mmc0: no vqmmc regulator found
[ 1.202295] mmc0: no vmmc regulator found
[ 1.246017] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.254697] usbcore: registered new interface driver usbhid
[ 1.260219] usbhid: USB HID core driver
[ 1.264911] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.271201] nand: Micron MT29F2G08ABAEAWP
[ 1.275172] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.281114] Bad block table found at page 131008, version 0x01
[ 1.287333] Bad block table found at page 130944, version 0x01
[ 1.293379] 3 ofpart partitions found on MTD device pl353-nand
[ 1.299151] Creating 3 MTD partitions on "pl353-nand":
[ 1.304253] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.312314] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.319612] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.330343] TCP: cubic registered
[ 1.333580] NET: Registered protocol family 17
[ 1.338292] Registering SWP/SWPB emulation handler
[ 1.344145] regulator-dummy: disabling
[ 1.348533] UBI: attaching mtd1 to ubi0
[ 1.874107] UBI: scanning is finished
[ 1.885698] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.892780] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.899542] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.906228] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.913064] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.919065] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.926189] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1151692613
[ 1.935198] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.944432] UBI: background thread "ubi_bgt0d" started, PID 1084
[ 1.944437] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.948384] ALSA device list:
[ 1.948387] No soundcards found.
[ 1.964726] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[ 1.993821] UBIFS: recovery needed
[ 2.086373] UBIFS: recovery completed
[ 2.090042] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 2.095970] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 2.105105] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.114988] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.120028] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 7CB6B46E-224A-4550-9A92-F6ED1D649181, small LPT model
[ 2.131302] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.138498] devtmpfs: mounted
[ 2.141601] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[ 2.982671] random: dd urandom read with 1 bits of entropy available
[ 3.366048]
[ 3.366048] bcm54xx_config_init
[ 4.426042]
[ 4.426042] bcm54xx_config_init
[ 8.426866] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 8.432970] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 22.981828] In axi fpga driver!
[ 22.984895] request_mem_region OK!
[ 22.988323] AXI fpga dev virtual address is 0xdf9fe000
[ 22.993393] *base_vir_addr = 0xc725
[ 23.008103] In fpga mem driver!
[ 23.011383] request_mem_region OK!
[ 23.014930] fpga mem virtual address is 0xe2000000
[ 23.816015]
[ 23.816015] bcm54xx_config_init
[ 24.906014]
[ 24.906014] bcm54xx_config_init
[ 28.906854] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 28.912957] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 1048.709037] random: nonblocking pool is initialized
main.c:13992: log_level = 4
main.c:14019: This is XILINX board. Totalram: 507486208
main.c:14031: Detect 512MB control board of XILINX
driver-bitmain.c:1776: mmap axi_fpga_addr = 0xb6f31000
driver-bitmain.c:1781: axi_fpga_addr data = 0xc725
driver-bitmain.c:1797: mmap fpga_mem_addr = 0xb5d2a000
driver-bitmain.c:994: forceFreq=-1 forceFlag=0
driver-bitmain.c:1696: min work minertest[0]:912
main.c:8570: DETECT HW version=8000c725
main.c:14064: miner ID : 80146d281540881c
main.c:14097: Miner Type = T9+
main.c:14101: AsicType = 1387
main.c:14104: real AsicNum = 18
main.c:14197: use critical mode to search freq...
driver-bitmain.c:1876: get PLUG ON=0x07003f0e
driver-bitmain.c:1907: Find hashboard on Chain[1]
driver-bitmain.c:1907: Find hashboard on Chain[2]
driver-bitmain.c:1907: Find hashboard on Chain[3]
driver-bitmain.c:1907: Find hashboard on Chain[8]
driver-bitmain.c:1907: Find hashboard on Chain[9]
driver-bitmain.c:1907: Find hashboard on Chain[10]
driver-bitmain.c:1907: Find hashboard on Chain[11]
driver-bitmain.c:1907: Find hashboard on Chain[12]
driver-bitmain.c:1907: Find hashboard on Chain[13]
main.c:2126: chain[1] PIC jump to app
main.c:2134: Check chain[1] PIC fw version=0x90
main.c:2126: chain[2] PIC jump to app
main.c:2134: Check chain[2] PIC fw version=0x90
main.c:2126: chain[3] PIC jump to app
main.c:2134: Check chain[3] PIC fw version=0x90
main.c:8651: Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8665: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9022: chain[1] has freq in PIC and will jump over...
main.c:9026: Chain[1] has core num in PIC
main.c:8651: Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x11 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8665: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9022: chain[2] has freq in PIC and will jump over...
main.c:9026: Chain[2] has core num in PIC
main.c:8651: Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8665: chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9022: chain[3] has freq in PIC and will jump over...
main.c:9026: Chain[3] has core num in PIC
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9022: chain[8] has freq in PIC and will jump over...
main.c:9026: Chain[8] has core num in PIC
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9022: chain[9] has freq in PIC and will jump over...
main.c:9026: Chain[9] has core num in PIC
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9022: chain[10] has freq in PIC and will jump over...
main.c:9026: Chain[10] has core num in PIC
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9022: chain[11] has freq in PIC and will jump over...
main.c:9026: Chain[11] has core num in PIC
main.c:9036: Chain[11] ASIC[6] has core num=1
main.c:9036: Chain[11] ASIC[7] has core num=1
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9022: chain[12] has freq in PIC and will jump over...
main.c:9026: Chain[12] has core num in PIC
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9022: chain[13] has freq in PIC and will jump over...
main.c:9026: Chain[13] has core num in PIC
main.c:9183: get PIC voltage=11 on chain[1], value=870
main.c:9183: get PIC voltage=11 on chain[2], value=870
main.c:9183: get PIC voltage=7 on chain[3], value=890
main.c:9183: get PIC voltage=11 on chain[8], value=870
main.c:9183: get PIC voltage=11 on chain[9], value=870
main.c:9183: get PIC voltage=11 on chain[10], value=870
main.c:9183: get PIC voltage=11 on chain[11], value=870
main.c:9183: get PIC voltage=7 on chain[12], value=890
main.c:9183: get PIC voltage=7 on chain[13], value=890
main.c:9349: chain[8] temp offset record: 1,2,0,0,0,0,33,28
main.c:9366: chain[8] temp chip I2C addr=0x98
main.c:9349: chain[10] temp offset record: 1,-1,0,0,0,0,33,28
main.c:9366: chain[10] temp chip I2C addr=0x98
main.c:9349: chain[12] temp offset record: 1,2,0,0,0,0,33,28
main.c:9366: chain[12] temp chip I2C addr=0x98
main.c:13956: total_exist_chain_num = 9
main.c:9562: CRC error counter=0
main.c:9577: set command mode to VIL
main.c:9649:
--- check asic number
main.c:9745: After Get ASIC NUM CRC error counter=0
main.c:9768: set_baud=0
main.c:10693: The min freq=700
main.c:10695: set real timeout 52, need sleep=379392
main.c:12825: After TEST CRC error counter=0
main.c:14236: search freq for 1 times, completed chain = 9, total chain num = 9
main.c:14645: restart Miner chance num=2
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13927: bmminer not found= 1853 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
main.c:13927: bmminer not found=28179 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
main.c:13927: bmminer not found=21952 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
main.c:13927: bmminer not found=15783 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
driver-btm-c5.c:12243:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12292:bitmain_c5_init: Detect 512MB control board of XILINX
driver-btm-c5.c:12321:bitmain_c5_init: Miner Type = T9+
driver-btm-c5.c:12324:bitmain_c5_init: Miner compile time: Wed Jul 31 16:20:36 CST 2019 type: Antminer T9+
driver-btm-c5.c:12414:bitmain_c5_init: miner ID : 80146d281540881c
driver-btm-c5.c:12571:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6000
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=5880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6000
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=5880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6000
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=5880
driver-btm-c5.c:1680:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1685:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[1] PIC fw version=0x90
do read_temp_func once...
get RT hashrate from Chain[1]: (asic index start from 1-18)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000
get RT hashrate from Chain[2]: (asic index start from 1-18)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000
get RT hashrate from Chain[8]: (asic index start from 1-18)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=5243.42 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000
get RT hashrate from Chain[9]: (asic index start from 1-18)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000
get RT hashrate from Chain[10]: (asic index start from 1-18)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000
get RT hashrate from Chain[11]: (asic index start from 1-18)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000
Check Chain[J2] ASIC RT error: (asic index start from 1-18)
Check Chain[J3] ASIC RT error: (asic index start from 1-18)
Check Chain[J9] ASIC RT error: (asic index start from 1-18)
Asic[06]=5243.420000
Check Chain[J10] ASIC RT error: (asic index start from 1-18)
Check Chain[J11] ASIC RT error: (asic index start from 1-18)
Check Chain[J12] ASIC RT error: (asic index start from 1-18)
Done check_asic_reg
Chain[8] Chip[0] pcb temperature=68
Chain[8] Chip[1] junction temperature=82
Special fix Chain[8] Chip[1] middle Temp = 83
Done read temp on Chain[8]
Chain[10] Chip[0] pcb temperature=65
Chain[10] Chip[1] junction temperature=77
Special fix Chain[10] Chip[1] middle Temp = 80
Done read temp on Chain[10]
Max pcb temp : 68
set FAN speed according to: temp_highest=68 temp_top1[PWM_T]=68 temp_top1[TEMP_POS_LOCAL]=68 temp_change=0 fix_fan_steps=0
FAN PWM: 86
read_temp_func Done!
CRC error counter=8969
|
