Please Help ANTMINER S9 newbie TROUBLESHOOT! Red flash on start. NO LIGHTS!

[ashleyminer123]

Firstly i was being silly and tried to power it down for noise manually because I have no point of advice until now. I unplugged 2 asic boards leaving middle plugged in and the suction fan on one side. Powered itself down a few times but was a bit quieter.  Did I break the middle board? I took it out and I only see heatsinks. Should I get a spare? When i find out how to cool it in mineral oil can I simply unplug one of the fans or will that pause the loop and cause an error? I surely don't need 2!

OVERVIEW:
shows no hardware version.

MINING STATUS:
No ASICS listed at all!!!!! (Will it run on one card as I imagined if it were working?) * I believed they had only 3 cards originally

I CAN'T REMEMBER WHERE BUT
The fans all say 0,0,0,0, and so on.

I can access the log:

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000313] ps7-ttc #0 at df804000, irq=43
[    0.000623] Console: colour dummy device 80x30
[    0.000654] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040211] pid_max: default: 32768 minimum: 301
[    0.040434] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040454] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042588] CPU: Testing write buffer coherency: ok
[    0.042919] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042979] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043204] L310 cache controller enabled
[    0.043224] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121035] CPU1: Booted secondary processor
[    0.210229] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210360] Brought up 2 CPUs
[    0.210379] SMP: Total of 2 processors activated.
[    0.210387] CPU: All CPU(s) started in SVC mode.
[    0.211050] devtmpfs: initialized
[    0.213464] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214675] regulator-dummy: no parameters
[    0.221908] NET: Registered protocol family 16
[    0.224147] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226447] cpuidle: using governor ladder
[    0.226460] cpuidle: using governor menu
[    0.233870] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235398] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235411] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235525] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.257202] bio: create slab <bio-0> at 0
[    0.258632] vgaarb: loaded
[    0.259328] SCSI subsystem initialized
[    0.260970] usbcore: registered new interface driver usbfs
[    0.261341] usbcore: registered new interface driver hub
[    0.261579] usbcore: registered new device driver usb
[    0.262104] media: Linux media interface: v0.10
[    0.262261] Linux video capture interface: v2.00
[    0.262506] pps_core: LinuxPPS API ver. 1 registered
[    0.262518] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.262639] PTP clock support registered
[    0.262999] EDAC MC: Ver: 3.0.0
[    0.264027] Advanced Linux Sound Architecture Driver Initialized.
[    0.266872] DMA-API: preallocated 4096 debug entries
[    0.266887] DMA-API: debugging enabled by kernel config
[    0.266959] Switched to clocksource arm_global_timer
[    0.287021] NET: Registered protocol family 2
[    0.287692] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.287750] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.287835] TCP: Hash tables configured (established 4096 bind 4096)
[    0.287879] TCP: reno registered
[    0.287896] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.287929] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.288166] NET: Registered protocol family 1
[    0.288510] RPC: Registered named UNIX socket transport module.
[    0.288522] RPC: Registered udp transport module.
[    0.288531] RPC: Registered tcp transport module.
[    0.288539] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288552] PCI: CLS 0 bytes, default 64
[    0.288996] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291034] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.293167] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293359] msgmni has been set to 967
[    0.294138] io scheduler noop registered
[    0.294151] io scheduler deadline registered
[    0.294195] io scheduler cfq registered (default)
[    0.308357] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.308378] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.431337] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.999132] console [ttyPS0] enabled
[    1.003412] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.011035] [drm] Initialized drm 1.1.0 20060810
[    1.028143] brd: module loaded
[    1.037479] loop: module loaded
[    1.046839] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.052712] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.060776] libphy: XEMACPS mii bus: probed
[    1.065144] ------------- phy_id = 0x3625e62
[    1.070191] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.078834] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.085450] ehci-pci: EHCI PCI platform driver
[    1.092688] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.099524] usbcore: registered new interface driver usb-storage
[    1.106385] mousedev: PS/2 mouse device common for all mice
[    1.112535] i2c /dev entries driver
[    1.119538] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.125020] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.130924] Xilinx Zynq CpuIdle Driver started
[    1.135764] sdhci: Secure Digital Host Controller Interface driver
[    1.141936] sdhci: Copyright(c) Pierre Ossman
[    1.146206] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.153058] mmc0: no vqmmc regulator found
[    1.157097] mmc0: no vmmc regulator found
[    1.196976] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.205671] usbcore: registered new interface driver usbhid
[    1.211182] usbhid: USB HID core driver
[    1.215900] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.222195] nand: Micron MT29F2G08ABAEAWP
[    1.226160] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.232111] Bad block table found at page 131008, version 0x01
[    1.238337] Bad block table found at page 130944, version 0x01
[    1.244387] 3 ofpart partitions found on MTD device pl353-nand
[    1.250169] Creating 3 MTD partitions on "pl353-nand":
[    1.255264] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.263322] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.270648] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.279614] TCP: cubic registered
[    1.282850] NET: Registered protocol family 17
[    1.287562] Registering SWP/SWPB emulation handler
[    1.293430] regulator-dummy: disabling
[    1.297771] UBI: attaching mtd1 to ubi0
[    1.822731] UBI: scanning is finished
[    1.834344] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.841426] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.848187] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.854851] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.861729] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.867710] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.874817] UBI: max/mean erase counter: 28/16, WL threshold: 4096, image sequence number: 1105122292
[    1.884034] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.893251] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.893257] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.897222] ALSA device list:
[    1.897225]   No soundcards found.
[    1.913591] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.942686] UBIFS: recovery needed
[    2.021432] UBIFS: recovery completed
[    2.025105] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.031058] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.040162] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.050085] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.055080] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 3B7239D8-21A7-4628-8BEE-5D1CF3D22D35, small LPT model
[    2.066381] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.073800] devtmpfs: mounted
[    2.076901] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.917826] random: dd urandom read with 0 bits of entropy available
[    3.307004] 
[    3.307004] bcm54xx_config_init
[    3.917009] 
[    3.917009] bcm54xx_config_init
[    7.917827] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[    7.923936] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[   25.601391] In axi fpga driver!
[   25.604462] request_mem_region OK!
[   25.607886] AXI fpga dev virtual address is 0xdf9fc000
[   25.612960] *base_vir_addr = 0x8c510
[   25.628043] In fpga mem driver!
[   25.631224] request_mem_region OK!
[   25.634786] fpga mem virtual address is 0xe2000000
[   26.426378] 
[   26.426378] bcm54xx_config_init
[   27.056329] 
[   27.056329] bcm54xx_config_init
[   31.056763] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   31.062871] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
main.c:13927: log_level = 4
main.c:13954: This is XILINX board. Totalram:       507527168
main.c:13966: Detect 512MB control board of XILINX
driver-bitmain.c:1003: forceFreq=-1 forceFlag=0
main.c:8434: DETECT HW version=0008c510
main.c:13999: miner ID : 8058ec0005904814
main.c:14024: Miner Type = S9
main.c:14036: AsicType = 1387
main.c:14039: real AsicNum = 63
main.c:13591: Find /tmp/searcherror: F:1  The last log is below:
main.c:13927: log_level = 4
main.c:13954: This is XILINX board. Totalram:       507527168
main.c:13966: Detect 512MB control board of XILINX
driver-bitmain.c:1003: forceFreq=-1 forceFlag=0
main.c:8434: DETECT HW version=0008c510
main.c:13999: miner ID : 8058ec0005904814
main.c:14024: Miner Type = S9
main.c:14036: AsicType = 1387
main.c:14039: real AsicNum = 63
main.c:14132: use critical mode to search freq...
driver-bitmain.c:2401: get PLUG ON=0x000000e0
driver-bitmain.c:2471: Find hashboard on Chain[5]
driver-bitmain.c:2471: Find hashboard on Chain[6]
driver-bitmain.c:2471: Find hashboard on Chain[7]
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
main.c:2164: Check chain[5] PIC fw version=0x03
main.c:2164: Check chain[6] PIC fw version=0x03
main.c:2164: Check chain[7] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[5] has freq in PIC and will jump over...
main.c:8965: Chain[5] has core num in PIC
main.c:2164: Check chain[5] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[6] has freq in PIC and will jump over...
main.c:8965: Chain[6] has core num in PIC
main.c:2164: Check chain[6] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[7] has freq in PIC and will jump over...
main.c:8965: Chain[7] has core num in PIC
main.c:8975: Chain[7] ASIC[28] has core num=4
main.c:2164: Check chain[7] PIC fw version=0x03
main.c:9039: get PIC voltage=142 on chain[5], value=860
main.c:9039: get PIC voltage=142 on chain[6], value=860
main.c:9039: get PIC voltage=142 on chain[7], value=860
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:9205: chain[5] temp offset record: 62,0,0,0,0,0,37,28
main.c:9222: chain[5] temp chip I2C addr=0x98
main.c:9228: chain[5] has no middle temp, use special fix mode.
main.c:9205: chain[6] temp offset record: 62,0,0,0,0,0,37,28
main.c:9222: chain[6] temp chip I2C addr=0x98
main.c:9228: chain[6] has no middle temp, use special fix mode.
main.c:9205: chain[7] temp offset record: 62,0,0,0,0,0,37,28
main.c:9222: chain[7] temp chip I2C addr=0x98
main.c:9228: chain[7] has no middle temp, use special fix mode.
main.c:13838: total_exist_chain_num = 3
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:9456: CRC error counter=0
main.c:9471: set command mode to VIL
main.c:9543: 
--- check asic number
main.c:9640: After Get ASIC NUM CRC error counter=0
main.c:9663: set_baud=0
main.c:10588: The min freq=700
main.c:10590: set real timeout 52, need sleep=379392
main.c:12720: After TEST CRC error counter=0
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:14167: search freq for 1 times, completed chain = 3, total chain num = 3 
board_frq_tuning.c:549: single_board_frq_tuning enter
board_frq_tuning.c:550: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:132: force_freq not set, don't need tuning
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:14559: restart Miner chance num=2
main.c:14599: waiting for receive_func to exit!
main.c:14613: waiting for pic heart to exit!
main.c:13809: bmminer not found= 1378 root       0:00 grep bmminer

main.c:14657: bmminer not found, restart bmminer ...
This is the first time running after searching freq!
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Jul 13 10:46:43 CST 2018 type: Antminer S9j
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 8058ec0005904814
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
get fan[5] speed=6120
Fatal Error: some Fan lost or Fan speed low!

I will pay for a fixable solution or suggestion so please send any preferred address for whatever currency I can send (up to) $20 for a correct solution.

[thierry4wd]

hi, your kernel showing ONE fan lost or defected ... You need replace one fan, on other than slot 5

[ashleyminer123]

Are you sure sure its the fan? I know the log says about a fan. Would it still show no hardware? They spin and everything and change speeds. Thankyou so much. Can i get a fan testing kit? If thats true and I can prove it then please send a bitcoin adress for my appreciation

[mikeywith]

When the fans don't work, the miner won't initialize and that would result to so many weird errors, there could be other problems but without fixing the fan first - there is nothing you can do.

if 1 fan spins it will cause the other fan to spin even if the latter was dead, if you unplug the good fan, you will notice that the dead one will stop spinning.

Can i get a fan testing kit?

What kit do you need? just follow the 4 pin wire from the fan to the control board, you will find fan5 and fan4, the one attached to fan5 is the bad one (if the wires haven't been tampered with, fan5 is the exhaust (rear) fan), the best way to confirm this is by switching the wires, fan5 goes to fan4 and vice versa.

Results will be

1- Fan5 is good, fan 4 is bad > (original fan 5 is bad ) which is the most likely scenario
2- Fan4 is good fan 5 is bad > (fan is good, something else is bad) this is very less likely to happen.

also notice that your control board might have fan5 and fan6 instead of fan4 and fan5, it doesn't really matter.