Antminer S9 - hashboard detected but no work

[naughtyju]

Hi everybody.

I ve just received my S9k, with 3 boards, but only 2 work. I wd like understand why the third doesnt work.

Before my post, I check all 6-pins form power supply, all pins of connectors, I open the S9 and look all boards, all it's ok. After, I change the channel of bad board from chain[1] to chain[0].
Edit : I forgot, of course I check on the forum before this post !

The firmware :

Hardware Version   13.10.1.3
Kernel Version   Linux 4.6.0-xilinx-gff8137b-dirty #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
File System Version   Thu Jul 11 20:09:08 CST 2019
CGminer Version   4.9.0

Below, the kernel log :

=> the not working board is on chain[0]. It's strange, the board asks, the 60 ASIC frequencies are ok, but the test of "bring up chain 0" failed and the number of ASIC is wrong (50 only found). I dont understand why. Could you held me please ?

Thanks you.

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 198640K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30736K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 17696K (cc9b8000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Broadcom BCM5241 e000b000.etherne:00: attached PHY driver [Broadcom BCM5241] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 514465032
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 30CB12EE-B9CE-4E2B-B771-12C508ACED28, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1352/337, WL threshold: 4096, image sequence number: 3398628109
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 809BFBD4-4328-4FAA-81CC-F7FB4A57F002, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb34000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
 [2021-01-11 17:00:25.624] httpListenThread start ret=0
 [2021-01-11 17:00:55.625] start listen on 6060 ...
 [2021-01-11 17:04:31.176] setStartTimePoint total_tv_start_sys=282 total_tv_end_sys=283

2021-01-11 17:00:25 driver-btm-soc.c:6310:bitmain_soc_init: This is Antminer S9k scan user version
2021-01-11 17:00:25 driver-btm-soc.c:6316:bitmain_soc_init: special mode: disabled
2021-01-11 17:00:25 driver-btm-soc.c:6323:bitmain_soc_init: This is high performance mode
2021-01-11 17:00:25 driver-btm-soc.c:6328:bitmain_soc_init: last commit version: 37a3761 commit time: 2019-07-11 20:12:37 build: 2019-07-11 20:16:12
2021-01-11 17:00:25 driver-btm-soc.c:6349:bitmain_soc_init: Detect 256MB control board of XILINX
2021-01-11 17:00:25 driver-btm-soc.c:6352:bitmain_soc_init: Miner compile time: Thu Jul 11 20:09:08 CST 2019 type: Antminer S9k
2021-01-11 17:00:25 driver-btm-soc.c:848:check_chain: get_hash_on_plug is 0x7
2021-01-11 17:00:25 driver-btm-soc.c:860:check_chain: !! chain[0]is exist
2021-01-11 17:00:25 driver-btm-soc.c:860:check_chain: !! chain[1]is exist
2021-01-11 17:00:25 driver-btm-soc.c:860:check_chain: !! chain[2]is exist
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fb 28 fb ff
00000080 ff ff ff ff ff ff ff b9   49 49 49 49 49 49 49 49
00000090 49 49 49 49 49 49 49 49   49 49 49 49 49 49 49 49
000000a0 49 49 49 49 49 49 49 49   49 49 49 49 49 49 49 49
000000b0 49 49 49 49 49 49 49 49   49 49 49 49 49 49 49 49
000000c0 49 49 49 49 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff 9a 11 00 00   10 ff ff ff 39 10 03 35
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fb 28 fc ff
00000080 ff ff ff ff ff ff ff b9   49 49 49 49 49 49 49 49
00000090 49 49 49 49 49 49 49 49   49 49 49 49 49 49 49 49
000000a0 49 49 49 49 49 49 49 49   49 49 49 49 49 49 49 49
000000b0 49 49 49 49 49 49 49 49   49 49 49 49 49 49 49 49
000000c0 49 49 49 49 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff 83 11 00 00   10 ff ff ff 39 10 d0 9b
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fc 28 fb ff
00000080 ff ff ff ff ff ff ff b9   4b 4b 4b 4b 4b 4b 4b 4b
00000090 4b 4b 4b 4b 4b 4b 4b 4b   4b 4b 4b 4b 4b 4b 4b 4b
000000a0 4b 4b 4b 4b 4b 4b 4b 4b   4b 4b 4b 4b 4b 4b 4b 4b
000000b0 4b 4b 4b 4b 4b 4b 4b 4b   4b 4b 4b 4b 4b 4b 4b 4b
000000c0 4b 4b 4b 4b 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff 11 12 00 00   10 ff ff ff 39 10 b8 fd

read chain[0] hardware info:
major type: 0
minor type: 2
chip level: 0
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

read chain[1] hardware info:
major type: 0
minor type: 2
chip level: 0
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

read chain[2] hardware info:
major type: 0
minor type: 2
chip level: 0
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

sweep config for eco mode: 
sweep_start_voltage: 9.25
max_aging_voltage:   9.65
sweep_min_freq:      300M
sweep_max_freq:      350M

sweep config for hpf mode: 
sweep_start_voltage: 9.70
max_aging_voltage:   10.10
sweep_min_freq:      355M
sweep_max_freq:      385M
2021-01-11 17:00:37 driver-btm-soc.c:5772:get_freq_result_from_eeprom: orginal chip freq: 
chain 0 freq:
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 

chain 1 freq:
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 

chain 2 freq:
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 

2021-01-11 17:00:37 driver-btm-soc.c:6443:bitmain_soc_init: reset all...
2021-01-11 17:00:39 driver-btm-soc.c:6451:bitmain_soc_init: miner ID : 81440d417b80885c
2021-01-11 17:00:39 driver-btm-soc.c:6114:init_miner_version: FPGA Version = 0xB00D
2021-01-11 17:00:58 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[0] PIC software version: 177
2021-01-11 17:00:59 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[1] PIC software version: 177
2021-01-11 17:01:00 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[2] PIC software version: 177
2021-01-11 17:01:00 power.c:183:power_init: power init ... 
2021-01-11 17:01:00 driver-btm-soc.c:4890:get_working_voltage_from_eeprom: get working vol [ 9.70] from chain[0] eeprom
2021-01-11 17:01:00 power.c:230:set_working_voltage_by_chain: chain[0] working_voltage = 9.700000
2021-01-11 17:01:00 driver-btm-soc.c:4890:get_working_voltage_from_eeprom: get working vol [ 9.70] from chain[1] eeprom
2021-01-11 17:01:00 power.c:230:set_working_voltage_by_chain: chain[1] working_voltage = 9.700000
2021-01-11 17:01:00 driver-btm-soc.c:4890:get_working_voltage_from_eeprom: get working vol [ 9.70] from chain[2] eeprom
2021-01-11 17:01:00 power.c:230:set_working_voltage_by_chain: chain[2] working_voltage = 9.700000
2021-01-11 17:01:00 driver-btm-soc.c:5562:update_highest_voltage: chain 0 hpf working voltage 9.70
2021-01-11 17:01:00 driver-btm-soc.c:5562:update_highest_voltage: chain 1 hpf working voltage 9.70
2021-01-11 17:01:00 driver-btm-soc.c:5562:update_highest_voltage: chain 2 hpf working voltage 9.70
2021-01-11 17:01:00 driver-btm-soc.c:5571:update_highest_voltage: open core at max voltage 10.20
2021-01-11 17:01:00 power.c:779:set_iic_power_to_highest_voltage_by_chain: chain[0] setting to hightest voltage: 10.20 ...
2021-01-11 17:01:00 power.c:705:set_iic_power_by_voltage: now setting voltage to : 10.200000 
2021-01-11 17:01:00 power.c:779:set_iic_power_to_highest_voltage_by_chain: chain[1] setting to hightest voltage: 10.20 ...
2021-01-11 17:01:03 power.c:705:set_iic_power_by_voltage: now setting voltage to : 10.200000 
2021-01-11 17:01:03 power.c:779:set_iic_power_to_highest_voltage_by_chain: chain[2] setting to hightest voltage: 10.20 ...
2021-01-11 17:01:04 power.c:705:set_iic_power_by_voltage: now setting voltage to : 10.200000 
2021-01-11 17:01:04 driver-btm-soc.c:1227:get_ideal_hash_rate: get ideal hash rate 13500
2021-01-11 17:01:04 eeprom.c:669:travel_eeprom_store: chain[0] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:365 IC[001]:365 IC[002]:365 IC[003]:365 IC[004]:365 IC[005]:365 IC[006]:365 IC[007]:365 IC[008]:365 IC[009]:365 
IC[010]:365 IC[011]:365 IC[012]:365 IC[013]:365 IC[014]:365 IC[015]:365 IC[016]:365 IC[017]:365 IC[018]:365 IC[019]:365 
IC[020]:365 IC[021]:365 IC[022]:365 IC[023]:365 IC[024]:365 IC[025]:365 IC[026]:365 IC[027]:365 IC[028]:365 IC[029]:365 
IC[030]:365 IC[031]:365 IC[032]:365 IC[033]:365 IC[034]:365 IC[035]:365 IC[036]:365 IC[037]:365 IC[038]:365 IC[039]:365 
IC[040]:365 IC[041]:365 IC[042]:365 IC[043]:365 IC[044]:365 IC[045]:365 IC[046]:365 IC[047]:365 IC[048]:365 IC[049]:365 
IC[050]:365 IC[051]:365 IC[052]:365 IC[053]:365 IC[054]:365 IC[055]:365 IC[056]:365 IC[057]:365 IC[058]:365 IC[059]:365 
voltage in mode2: 9.70 V
hash rate in mode2: 04506 GH/s

2021-01-11 17:01:04 eeprom.c:669:travel_eeprom_store: chain[1] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:365 IC[001]:365 IC[002]:365 IC[003]:365 IC[004]:365 IC[005]:365 IC[006]:365 IC[007]:365 IC[008]:365 IC[009]:365 
IC[010]:365 IC[011]:365 IC[012]:365 IC[013]:365 IC[014]:365 IC[015]:365 IC[016]:365 IC[017]:365 IC[018]:365 IC[019]:365 
IC[020]:365 IC[021]:365 IC[022]:365 IC[023]:365 IC[024]:365 IC[025]:365 IC[026]:365 IC[027]:365 IC[028]:365 IC[029]:365 
IC[030]:365 IC[031]:365 IC[032]:365 IC[033]:365 IC[034]:365 IC[035]:365 IC[036]:365 IC[037]:365 IC[038]:365 IC[039]:365 
IC[040]:365 IC[041]:365 IC[042]:365 IC[043]:365 IC[044]:365 IC[045]:365 IC[046]:365 IC[047]:365 IC[048]:365 IC[049]:365 
IC[050]:365 IC[051]:365 IC[052]:365 IC[053]:365 IC[054]:365 IC[055]:365 IC[056]:365 IC[057]:365 IC[058]:365 IC[059]:365 
voltage in mode2: 9.70 V
hash rate in mode2: 04483 GH/s

2021-01-11 17:01:04 eeprom.c:669:travel_eeprom_store: chain[2] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:375 IC[001]:375 IC[002]:375 IC[003]:375 IC[004]:375 IC[005]:375 IC[006]:375 IC[007]:375 IC[008]:375 IC[009]:375 
IC[010]:375 IC[011]:375 IC[012]:375 IC[013]:375 IC[014]:375 IC[015]:375 IC[016]:375 IC[017]:375 IC[018]:375 IC[019]:375 
IC[020]:375 IC[021]:375 IC[022]:375 IC[023]:375 IC[024]:375 IC[025]:375 IC[026]:375 IC[027]:375 IC[028]:375 IC[029]:375 
IC[030]:375 IC[031]:375 IC[032]:375 IC[033]:375 IC[034]:375 IC[035]:375 IC[036]:375 IC[037]:375 IC[038]:375 IC[039]:375 
IC[040]:375 IC[041]:375 IC[042]:375 IC[043]:375 IC[044]:375 IC[045]:375 IC[046]:375 IC[047]:375 IC[048]:375 IC[049]:375 
IC[050]:375 IC[051]:375 IC[052]:375 IC[053]:375 IC[054]:375 IC[055]:375 IC[056]:375 IC[057]:375 IC[058]:375 IC[059]:375 
voltage in mode2: 9.70 V
hash rate in mode2: 04625 GH/s

2021-01-11 17:01:04 driver-btm-soc.c:6494:bitmain_soc_init: fan_eft : 0  fan_pwm : 0
2021-01-11 17:01:04 driver-btm-soc.c:6143:bring_up_chain: 

bring up chain 0
2021-01-11 17:01:05 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-01-11 17:01:36 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-01-11 17:01:39 driver-btm-soc.c:3820:check_asic_num: without pre_open_core chain 0, find asic num = 50
2021-01-11 17:01:39 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-01-11 17:01:40 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-01-11 17:01:42 driver-btm-soc.c:3820:check_asic_num: without pre_open_core chain 0, find asic num = 50
2021-01-11 17:01:42 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-01-11 17:01:43 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-01-11 17:01:44 driver-btm-soc.c:3828:check_asic_num: check asic num with pre_open_core
2021-01-11 17:01:44 driver-btm-soc.c:3793:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 0
2021-01-11 17:01:44 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-01-11 17:01:45 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-01-11 17:01:46 driver-btm-soc.c:3761:check_asic_num_without_power_off: Open 5 core for chain 0
2021-01-11 17:01:46 driver-btm-soc.c:3866:open_core_BM1393_pre_open: pre open core = 5
2021-01-11 17:01:47 driver-btm-soc.c:3746:pre_open_core_one_chain: for chain 0
2021-01-11 17:01:48 driver-btm-soc.c:3767:check_asic_num_without_power_off: chain 0, find asic num = 50
2021-01-11 17:01:48 driver-btm-soc.c:3793:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 1
2021-01-11 17:01:48 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-01-11 17:01:49 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-01-11 17:01:50 driver-btm-soc.c:3761:check_asic_num_without_power_off: Open 5 core for chain 0
2021-01-11 17:01:50 driver-btm-soc.c:3866:open_core_BM1393_pre_open: pre open core = 5
2021-01-11 17:01:50 driver-btm-soc.c:3746:pre_open_core_one_chain: for chain 0
2021-01-11 17:01:52 driver-btm-soc.c:3767:check_asic_num_without_power_off: chain 0, find asic num = 50
2021-01-11 17:01:52 driver-btm-soc.c:3850:check_asic_num: chian 0 check asic number failed! 
2021-01-11 17:01:52 driver-btm-soc.c:6143:bring_up_chain: 

bring up chain 1
2021-01-11 17:01:53 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-01-11 17:02:25 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-01-11 17:02:26 driver-btm-soc.c:3820:check_asic_num: without pre_open_core chain 1, find asic num = 60
2021-01-11 17:02:29 driver-btm-soc.c:4643:set_freq_by_chain: chain[1] set freq:100.00
2021-01-11 17:02:30 driver-btm-soc.c:3866:open_core_BM1393_pre_open: pre open core = 13
2021-01-11 17:02:30 driver-btm-soc.c:3746:pre_open_core_one_chain: for chain 1
2021-01-11 17:02:30 temperature.c:581:is_eeprom_tempsensor_data_correct: check sensor info ...
2021-01-11 17:02:30 temperature.c:596:is_eeprom_tempsensor_data_correct: sensor type is TMP451
2021-01-11 17:02:30 temperature.c:608:is_eeprom_tempsensor_data_correct: 2
2021-01-11 17:02:30 temperature.c:622:is_eeprom_tempsensor_data_correct: sensor num is 2
2021-01-11 17:02:30 temperature.c:631:is_eeprom_tempsensor_data_correct: sensor pos = 31, 40, 0, 0
2021-01-11 17:02:30 temperature.c:649:is_eeprom_tempsensor_data_correct: chain[1] temp sensor info, correct!
2021-01-11 17:02:30 temperature.c:738:check_eeprom_calibration_data: chain[1] no need to calibrate !
2021-01-11 17:02:30 temperature.c:514:is_tempsensor_data_correct: Bad,temp_info.type = 0
2021-01-11 17:02:30 temperature.c:753:calibration_sensor_offset: chain[1] temp info,Bad. Reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0 
sensor offset: -5  -4  0  0  0  0 
2021-01-11 17:02:30 temperature.c:791:calibration_sensor_offset: get temp info from eeprom,just use it!
2021-01-11 17:02:30 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x7a61, cmd_buf[2]=0x1a000000, misc=0x7a61
2021-01-11 17:02:31 temperature.c:808:calibration_sensor_offset: Chain[1] chip[31] use PIC middle temp offset=-5, typeID=55
2021-01-11 17:02:31 temperature.c:336:do_calibration_sensor_offset_by_eeprom: New offset - Chain[1] Chip[31] local:0 remote:0 offset:-5 
2021-01-11 17:02:31 temperature.c:860:calibration_sensor_offset: Chain[1] Chip[31] get middle temp offset=-5 typeID=55
2021-01-11 17:02:31 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x7a61, cmd_buf[2]=0x13000000, misc=0x7a61
2021-01-11 17:02:31 temperature.c:808:calibration_sensor_offset: Chain[1] chip[40] use PIC middle temp offset=-4, typeID=55
2021-01-11 17:02:31 temperature.c:336:do_calibration_sensor_offset_by_eeprom: New offset - Chain[1] Chip[40] local:0 remote:0 offset:-4 
2021-01-11 17:02:31 temperature.c:860:calibration_sensor_offset: Chain[1] Chip[40] get middle temp offset=-4 typeID=55
2021-01-11 17:02:31 driver-btm-soc.c:6143:bring_up_chain: 

bring up chain 2
2021-01-11 17:02:32 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-01-11 17:03:04 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2021-01-11 17:03:05 driver-btm-soc.c:3820:check_asic_num: without pre_open_core chain 2, find asic num = 60
2021-01-11 17:03:09 driver-btm-soc.c:4643:set_freq_by_chain: chain[2] set freq:100.00
2021-01-11 17:03:09 driver-btm-soc.c:3866:open_core_BM1393_pre_open: pre open core = 13
2021-01-11 17:03:09 driver-btm-soc.c:3746:pre_open_core_one_chain: for chain 2
2021-01-11 17:03:09 temperature.c:581:is_eeprom_tempsensor_data_correct: check sensor info ...
2021-01-11 17:03:09 temperature.c:596:is_eeprom_tempsensor_data_correct: sensor type is TMP451
2021-01-11 17:03:09 temperature.c:608:is_eeprom_tempsensor_data_correct: 2
2021-01-11 17:03:09 temperature.c:622:is_eeprom_tempsensor_data_correct: sensor num is 2
2021-01-11 17:03:09 temperature.c:631:is_eeprom_tempsensor_data_correct: sensor pos = 31, 40, 0, 0
2021-01-11 17:03:09 temperature.c:649:is_eeprom_tempsensor_data_correct: chain[2] temp sensor info, correct!
2021-01-11 17:03:09 temperature.c:738:check_eeprom_calibration_data: chain[2] no need to calibrate !
2021-01-11 17:03:09 temperature.c:514:is_tempsensor_data_correct: Bad,temp_info.type = 0
2021-01-11 17:03:09 temperature.c:753:calibration_sensor_offset: chain[2] temp info,Bad. Reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0 
sensor offset: -4  -5  0  0  0  0 
2021-01-11 17:03:09 temperature.c:791:calibration_sensor_offset: get temp info from eeprom,just use it!
2021-01-11 17:03:09 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x7a61, cmd_buf[2]=0x1a000000, misc=0x7a61
2021-01-11 17:03:10 temperature.c:808:calibration_sensor_offset: Chain[2] chip[31] use PIC middle temp offset=-4, typeID=55
2021-01-11 17:03:10 temperature.c:336:do_calibration_sensor_offset_by_eeprom: New offset - Chain[2] Chip[31] local:0 remote:0 offset:-4 
2021-01-11 17:03:10 temperature.c:860:calibration_sensor_offset: Chain[2] Chip[31] get middle temp offset=-4 typeID=55
2021-01-11 17:03:10 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x7a61, cmd_buf[2]=0x13000000, misc=0x7a61
2021-01-11 17:03:10 temperature.c:808:calibration_sensor_offset: Chain[2] chip[40] use PIC middle temp offset=-5, typeID=55
2021-01-11 17:03:11 temperature.c:336:do_calibration_sensor_offset_by_eeprom: New offset - Chain[2] Chip[40] local:0 remote:0 offset:-5 
2021-01-11 17:03:11 temperature.c:860:calibration_sensor_offset: Chain[2] Chip[40] get middle temp offset=-5 typeID=55
2021-01-11 17:03:11 asic.c:1153:set_baud: set baud=1
2021-01-11 17:03:11 asic.c:1126:set_baud_one_chain: cmd_buf[0]=0x51090018, cmd_buf[1]=0x2101, cmd_buf[2]=0x11000000, misc=0x2101
2021-01-11 17:03:11 asic.c:1126:set_baud_one_chain: cmd_buf[0]=0x51090018, cmd_buf[1]=0x2101, cmd_buf[2]=0x11000000, misc=0x2101
2021-01-11 17:03:11 asic.c:1164:set_baud: read bc write is 0x82001a
2021-01-11 17:03:11 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x6161, cmd_buf[2]=0x13000000, misc=0x6161
2021-01-11 17:03:11 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x6161, cmd_buf[2]=0x1a000000, misc=0x6161
2021-01-11 17:03:11 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x6161, cmd_buf[2]=0x13000000, misc=0x6161
2021-01-11 17:03:11 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x6161, cmd_buf[2]=0x1a000000, misc=0x6161
2021-01-11 17:03:11 driver-btm-soc.c:6509:bitmain_soc_init: set TICKET_MASK
2021-01-11 17:03:11 temperature.c:1952:detect_startup_environment_temperature: Environment temperature: [12]
2021-01-11 17:03:11 driver-btm-soc.c:3897:set_clock_delay_control: set mode 0
2021-01-11 17:03:11 driver-btm-soc.c:3916:set_clock_delay_control: core_data = 0x04
2021-01-11 17:03:11 driver-btm-soc.c:3987:open_core_bm1393: Start Open Core!!
2021-01-11 17:03:15 driver-btm-soc.c:4054:open_core_bm1393: End Open Core!!
2021-01-11 17:03:15 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 125
2021-01-11 17:03:17 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 150
2021-01-11 17:03:18 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 175
2021-01-11 17:03:19 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 200
2021-01-11 17:03:20 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 225
2021-01-11 17:03:21 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 250
2021-01-11 17:03:22 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 275
2021-01-11 17:03:23 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 300
2021-01-11 17:03:24 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 325
2021-01-11 17:03:25 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 350
2021-01-11 17:03:26 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[1] increase to 365
2021-01-11 17:03:27 driver-btm-soc.c:5215:increase_freq_by_eeprom_slowly: max = 365 ,min = 365
2021-01-11 17:03:27 driver-btm-soc.c:5221:increase_freq_by_eeprom_slowly: chain[1] increaseing the diff freq ...
2021-01-11 17:03:27 driver-btm-soc.c:5249:increase_freq_by_eeprom_slowly: chain 1 final freq setting:
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
2021-01-11 17:03:27 driver-btm-soc.c:5261:increase_freq_by_eeprom_slowly: set chain 1 to working voltage
2021-01-11 17:03:27 power.c:1303:slowly_set_working_power_t11: set chain 1 to working voltage:
now setting chain[1]-volt[10.15]-data[012] 
now setting chain[1]-volt[10.09]-data[013] 
now setting 2021-01-11 17:03:33 dspic33ep16gs202.c:213:dsPIC33EP16GS202_pic_heart_beat: ERROR! failed on Chain[1] after 3 times try!
chain[1]-volt[10.04]-data[014] 
now setting chain[1]-volt[09.99]-data[015] 
now setting chain[1]-volt[09.94]-data[016] 
now setting chain[1]-volt[09.85]-data[018] 
now setting chain[1]-volt[09.76]-data[020] 
now setting chain[1]-volt[09.72]-data[021] 
2021-01-11 17:03:52 power.c:1318:slowly_set_working_power_t11: done!
2021-01-11 17:03:52 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 125
2021-01-11 17:03:53 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 150
2021-01-11 17:03:54 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 175
2021-01-11 17:03:55 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 200
2021-01-11 17:03:56 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 225
2021-01-11 17:03:57 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 250
2021-01-11 17:03:58 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 275
2021-01-11 17:03:59 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 300
2021-01-11 17:04:00 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 325
2021-01-11 17:04:01 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 350
2021-01-11 17:04:02 driver-btm-soc.c:5205:increase_freq_by_eeprom_slowly: chain[2] increase to 375
2021-01-11 17:04:03 driver-btm-soc.c:5215:increase_freq_by_eeprom_slowly: max = 375 ,min = 375
2021-01-11 17:04:03 driver-btm-soc.c:5221:increase_freq_by_eeprom_slowly: chain[2] increaseing the diff freq ...
2021-01-11 17:04:03 driver-btm-soc.c:5249:increase_freq_by_eeprom_slowly: chain 2 final freq setting:
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
2021-01-11 17:04:04 driver-btm-soc.c:5261:increase_freq_by_eeprom_slowly: set chain 2 to working voltage
2021-01-11 17:04:04 power.c:1303:slowly_set_working_power_t11: set chain 2 to working voltage:
now setting chain[2]-volt[10.15]-data[012] 
now setting chain[2]-volt[10.09]-data[013] 
now setting chain[2]-volt[10.04]-data[014] 
now setting chain[2]-volt[09.99]-data[015] 
now setting chain[2]-volt[09.94]-data[016] 
now setting chain[2]-volt[09.85]-data[018] 
now setting chain[2]-volt[09.76]-data[020] 
now setting chain[2]-volt[09.72]-data[021] 
2021-01-11 17:04:26 power.c:1318:slowly_set_working_power_t11: done!
2021-01-11 17:04:26 driver-btm-soc.c:6535:bitmain_soc_init: set to working voltage...
2021-01-11 17:04:26 power.c:1253:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage:
now setting 2021-01-11 17:04:27 dspic33ep16gs202.c:213:dsPIC33EP16GS202_pic_heart_beat: ERROR! failed on Chain[2] after 3 times try!
chain[1]-volt[09.72]-data[021] chain[2]-volt[09.72]-data[021] 
2021-01-11 17:04:30 power.c:1273:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage end!
now setting chain[1]-volt[09.72]-data[021] chain[2]-volt[09.72]-data[021] 
2021-01-11 17:04:30 driver-btm-soc.c:4942:set_timeout: freq 375 final timeout=349
2021-01-11 17:04:30 driver-btm-soc.c:2894:low_temp_process_parm_init: chip miner_type = [2]
2021-01-11 17:04:30 driver-btm-soc.c:2894:low_temp_process_parm_init: chip miner_type = [2]
2021-01-11 17:04:30 driver-btm-soc.c:3559:check_system_work: check system thread start...
2021-01-11 17:04:31 driver-btm-soc.c:6604:bitmain_soc_init: Init done!
2021-01-11 17:04:31 driver-btm-soc.c:7343:bitmain_soc_prepare: bitmain soc init success.
2021-01-11 17:04:31 temperature.c:1421:read_temp_func: bring_up_pcb_temp = 15
2021-01-11 17:04:31 temperature.c:1758:get_target_chip_temp: if startup in low temp environment: YES
2021-01-11 17:04:31 temperature.c:1604:_get_target_chip_temp_t11: chip miner_type = [2]
2021-01-11 17:04:31 temperature.c:1604:_get_target_chip_temp_t11: chip miner_type = [2]
2021-01-11 17:04:31 util.c:2178:process_version_mask: Pool 1 Version num is 2
2021-01-11 17:04:31 util.c:2178:process_version_mask: Pool 0 Version num is 2
2021-01-11 17:04:32 driver-btm-soc.c:7018:send_job: Version num 2
2021-01-11 17:09:31 driver-btm-soc.c:6281:need_mode2_startup: chain 1 rt_hash_rate 4639.81 ideal_hash_rate 4483

[philipma1957]

Can you mine with 2 boards an do 9th? Most likely your board is toast s9k's were not the best model.

I mine 2 s9k's with 2 boards.

[mikeywith]

First of all, I should say thank you for posting such a detailed and neat question, unlike 99% of the new members here who don't do basic troubleshooting before posting, heck they don't even post any details and expect us to tell them what's going on with their mining gear.

So your problem is

Code:

2021-01-11 17:01:52 driver-btm-soc.c:3767:check_asic_num_without_power_off: chain 0, find asic num = 50
2021-01-11 17:01:52 driver-btm-soc.c:3850:check_asic_num: chian 0 check asic number failed!

S9k has 60 Asics on each chain/hash board, the signal here was interpreted at the 50th chip, which suggests that either chip 49 or 50 has a problem, the problem could be a loose heatsink or a dead chip.

You have bought the worst mining gear bitmain has ever made, oh, not just bitmain, the worst anybody can make, it's bad enough that nobody can make a gear that is bad as it is, you follow the logic?

I have written a complete topic about, its title is WANRNING! Do Not Buy Antminer S9k, the failure rate for these gears is well above 70%, so please - be prepared.

Now back to your problem, you need to physically inspect the hashboard, apply some pressure on the heatsinks to see which ones fall, and then update the thread.

[philipma1957]

Gave you a merit keep posting and you will getup of newbie jai and become a jr member.

if it mines with the two boards like mine does at least you are ⅔ of a loaf so to speak .

I keep the dead board in the center slot and have it detached completely . so the software only tests the two boards.

I have found this is the best way to run s9k's the two boards on left and right simply do not overheat. and the controller does not even try to do the center board as it is fully detached so it boots and starts mining a tiny bit faster than a 3 board model.

It runs cooler and lowers your fan speeds as another bonus.

[naughtyju]

Thanks you every body for your responses. Nice.

@philipma1957 : I will make your config tks, effectivelly 2/3 is better than nothing. Like you, I hash 9 TH/s.
@mikeywith : It s my first worker, I sorry to not view your post before to buy the S9K. Now it 's a good way to learn, thanks to your helps of course.

Nevertheless, the bad board isnt dead because I ve a respond - I can try something. About @mikeywith 's solution, it's strange to not have a dash if a heatsinks fall or dead chip. But tks u very much for your idea - that's I need !

Anyway, I will try your solution tomorrow, I will inspect, try to remove the 49th and 50ht heatsinks with my stripper, try to check if the 49th and 50ht chips are ok.

But, I dont know where is the number location of chips on the hashboard. Maybe it writes on the board - I will see.
edit : I found : https://www.zeusbtc.com/manuals/repair-guide/Antminer-S9k-Hash-board-Repair-Guide.pdf

See you for the next.

[mikeywith]

Anyway, I will try your solution tomorrow, I will inspect, try to remove the 49th and 50ht heatsinks with my stripper, try to check if the 49th and 50ht chips are ok.

If you have the tools, then follow this video https://www.youtube.com/watch?v=5WH7g61d90w , the voltage and resistance of RI,BO, CLKO, and etc values might be different on the S9k, but usually, every row of chips is considered a domain which should give you the same readings with small variance, on the S9 the top row and bottom row read higher values than the middle rows, if you need more info regarding this do let me know I'll see what I can collect.

The video shows a fixture tool that you don't really need now (not worth it just to fix a broken S9k board) so just test all the chips manually one by one, start with 49,50,51, and then the row which contains them, usually the bad chip/s will be around that area, it's also common for chip no.0 to go missing, and then finally test all of them.

Keep in mind that to test the voltage the miner needs to be sending signals to the chips, which only happens for a few seconds before it stops, you can however test the resistance offline (no need to be plugged in) and then confirm the voltage, you have a few seconds from the time you turn it on until it stops, if you have the time, just power off and on as many times as you need to get all the readings, you save over a $100 on the fixture tool by doing so.

[naughtyju]

Hi. Juste some news. Of course, on the S9k model, pins test are very very very small and under heatsinks...

So, I have moved all heatsinks from uc49 to uc60, the last line (UC51-60) + 2 references (uc49-50). It's easier to check the voltage and resistance. I realize my measures with the minus on the otherside heatsink, and the other on pins test.

I have a resistance on all pins test and all ASICs. I have a tension of 1.7V on the RI pin test for the Uc49 and Uc50. But nothing on the RI pin test of Uc51, Uc52, Uc53. I think the Uc51 is dead - that seems to be a recurrent default on S9 antminer. And so no power goes to the next ones, because they are in-line.

Now, I will buy ASICs BM1393B and a 9mm-adapter for my thermal cleaner.

See you.

[zigzag30190]

Good morning all.

I have the same problem, plate chain(2) that does not start, you have an idea of the problem. thank you.

Code:

bring up chain 0
2021-01-20 13:05:33 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-01-20 13:06:04 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-01-20 13:06:06 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 0, find asic num = 60
2021-01-20 13:06:09 driver-btm-soc.c:4816:set_freq_by_chain: chain[0] set freq:100.00
2021-01-20 13:06:10 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 0
2021-01-20 13:06:10 driver-btm-soc.c:4090:set_clock_delay_control: core_data = 0x06
2021-01-20 13:06:10 temperature.c:614:is_eeprom_tempsensor_data_correct: sensor_num 2, sensor pos = 31, 40, 0, 0
2021-01-20 13:06:10 temperature.c:523:is_tempsensor_data_correct: Bad,temp_info.type = 0
2021-01-20 13:06:10 temperature.c:751:calibration_sensor_offset: chain[0] temp info is bad, reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0 
sensor offset: -5  -4  0  0  0  0 
2021-01-20 13:06:10 temperature.c:801:calibration_sensor_offset: Chain[0] chip[31] middle temp offset=-5, typeID=55
2021-01-20 13:06:11 temperature.c:801:calibration_sensor_offset: Chain[0] chip[40] middle temp offset=-4, typeID=55
2021-01-20 13:06:11 driver-btm-soc.c:6388:bring_up_chain: 

bring up chain 1
2021-01-20 13:06:12 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-01-20 13:06:43 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-01-20 13:06:45 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 1, find asic num = 60
2021-01-20 13:06:48 driver-btm-soc.c:4816:set_freq_by_chain: chain[1] set freq:100.00
2021-01-20 13:06:49 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 1
2021-01-20 13:06:49 driver-btm-soc.c:4090:set_clock_delay_control: core_data = 0x06
2021-01-20 13:06:49 temperature.c:614:is_eeprom_tempsensor_data_correct: sensor_num 2, sensor pos = 31, 40, 0, 0
2021-01-20 13:06:49 temperature.c:523:is_tempsensor_data_correct: Bad,temp_info.type = 0
2021-01-20 13:06:49 temperature.c:751:calibration_sensor_offset: chain[1] temp info is bad, reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0 
sensor offset: -4  -3  0  0  0  0 
2021-01-20 13:06:49 temperature.c:801:calibration_sensor_offset: Chain[1] chip[31] middle temp offset=-4, typeID=55
2021-01-20 13:06:50 temperature.c:801:calibration_sensor_offset: Chain[1] chip[40] middle temp offset=-3, typeID=55
2021-01-20 13:06:50 driver-btm-soc.c:6388:bring_up_chain: 

bring up chain 2
2021-01-20 13:06:51 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-01-20 13:07:22 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2021-01-20 13:07:25 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 2, find asic num = 0
2021-01-20 13:07:25 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-01-20 13:07:26 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2021-01-20 13:07:28 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 2, find asic num = 0
2021-01-20 13:07:28 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-01-20 13:07:29 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2021-01-20 13:07:30 driver-btm-soc.c:4011:check_asic_num: check asic num with pre_open_core
2021-01-20 13:07:30 driver-btm-soc.c:3976:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 0
2021-01-20 13:07:30 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-01-20 13:07:31 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2021-01-20 13:07:32 driver-btm-soc.c:3944:check_asic_num_without_power_off: Open 5 core for chain 2
2021-01-20 13:07:32 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 2
2021-01-20 13:07:33 driver-btm-soc.c:3950:check_asic_num_without_power_off: chain 2, find asic num = 0
2021-01-20 13:07:33 driver-btm-soc.c:3976:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 1
2021-01-20 13:07:33 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-01-20 13:07:34 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2021-01-20 13:07:35 driver-btm-soc.c:3944:check_asic_num_without_power_off: Open 5 core for chain 2
2021-01-20 13:07:35 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 2
2021-01-20 13:07:37 driver-btm-soc.c:3950:check_asic_num_without_power_off: chain 2, find asic num = 0
2021-01-20 13:07:37 driver-btm-soc.c:4033:check_asic_num: chian 2 check asic number failed! 
2021-01-20 13:07:37 asic.c:1153:set_baud: set baud=1
2021-01-20 13:07:37 asic.c:1269:set_asic_ticket_mask: set ticket mask 63
2021-01-20 13:07:38 temperature.c:2064:detect_startup_environment_temperature: Environment temperature: [13]
2021-01-20 13:07:38 driver-btm-soc.c:4160:open_core_bm1393: Start Open Core!!
2021-01-20 13:07:42 driver-btm-soc.c:4227:open_core_bm1393: End Open Core!!
2021-01-20 13:07:43 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 125
2021-01-20 13:07:45 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 150
2021-01-20 13:07:46 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 175
2021-01-20 13:07:48 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 200
2021-01-20 13:07:50 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 225
2021-01-20 13:07:52 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 250
2021-01-20 13:07:53 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 275
2021-01-20 13:07:55 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 300
2021-01-20 13:07:57 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 325
2021-01-20 13:07:59 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 350
2021-01-20 13:08:00 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 375
2021-01-20 13:08:02 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 395
2021-01-20 13:08:04 driver-btm-soc.c:5383:increase_freq_by_eeprom_slowly_by_chain: max = 450 ,min = 395
2021-01-20 13:08:04 driver-btm-soc.c:5389:increase_freq_by_eeprom_slowly_by_chain: chain[0] increaseing the diff freq ...
2021-01-20 13:08:12 driver-btm-soc.c:5418:increase_freq_by_eeprom_slowly_by_chain: chain 0 final freq setting:
450 450 435 450 395 450 435 450 395 450 
395 435 435 450 450 395 450 450 450 450 
450 395 450 450 450 450 450 435 395 435 
395 435 435 450 450 395 450 450 450 450 
450 395 450 450 450 450 450 435 435 395 
395 395 435 435 450 450 450 450 450 450 
2021-01-20 13:08:12 power.c:1309:slowly_set_working_power_t11: set chain 0 to working voltage:
now setting chain[0]-volt[09.89]-data[017] 
now setting chain[0]-volt[09.80]-data[019] 
now setting chain[0]-volt[09.72]-data[021] 
now setting chain[0]-volt[09.65]-data[023] 
now setting chain[0]-volt[09.58]-data[025] 
now setting chain[0]-volt[09.54]-data[026] 
now setting chain[0]-volt[09.51]-data[027] 
2021-01-20 13:08:39 power.c:1331:slowly_set_working_power_t11: done!
2021-01-20 13:08:39 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 125
2021-01-20 13:08:41 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 150
2021-01-20 13:08:42 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 175
2021-01-20 13:08:44 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 200
2021-01-20 13:08:46 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 225
2021-01-20 13:08:48 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 250
2021-01-20 13:08:49 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 275
2021-01-20 13:08:51 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 300
2021-01-20 13:08:53 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 325
2021-01-20 13:08:55 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 350
2021-01-20 13:08:56 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 375
2021-01-20 13:08:58 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 400
2021-01-20 13:09:00 driver-btm-soc.c:5383:increase_freq_by_eeprom_slowly_by_chain: max = 455 ,min = 400
2021-01-20 13:09:00 driver-btm-soc.c:5389:increase_freq_by_eeprom_slowly_by_chain: chain[1] increaseing the diff freq ...
2021-01-20 13:09:08 driver-btm-soc.c:5418:increase_freq_by_eeprom_slowly_by_chain: chain 1 final freq setting:

[arta2018]

HI

i have same problem with s9se 17 th. but suddenly i bring my home from farm(minifarm ) to test i realize it work in home no problem.

i think problem solved i take miner to farm but not worked , so i bring to home and it worked.

i dont what is reason ? i think some thing about frequency Interference.

[mikeywith]

I have the same problem, plate chain(2) that does not start, you have an idea of the problem. thank you.

You have to post the complete kernel log, and a screenshot of the miner's status page. posts in old topics can be hardly spotted, you should start your own topic and provide all the details needed to troubleshoot it.

i have same problem with s9se 17 th. but suddenly i bring my home from farm(minifarm ) to test i realize it work in home no problem.

This could be a voltage issue, what is the voltage at home and at the farm? S9es PSU's aren't very sensitive to voltage, but if the PSU is bad and not yet dead then voltage drop will affect it, you may troubleshoot this by trying a different PSU in the farm.