S17+_76 Trouble Flashing Bitmain Firmware After NiceHash Firmware

[ShineOn]

Hi, I have a new-to-me S17+_76. As soon as I got it I Flashed it with a micro SD with NiceHash's Firmware. The machine had all 3 boards working for 8 hours well at a lower than stock profile. Then I upped the profile to just below it's stock level 74Th. It was hashing really well. The room was toasty so I opened the window (Massachusetts). Then I woke up and saw the production dropped. After 4 hours Chain[1] dropped out. It was very cold in the room it was mining in, maybe it got too cold? So I reset the machine at the first profile at the lower rate.

Chain[1] wouldn't work: "src/chip139x.c:1049 chain[1] - Failed to receive chip replies" and "ERROR: driver-btm-chain.c:488 chain[1] - Failed to detect ASIC chips"

Then Chain[0] to did temporarily...it was coding a faulty sensor "ERROR: src/temp.c:172 chain[0] sen[1] - Disabling faulty sensor, pcb=26 chip=-64" , but still fired up temporarily and then "ERROR: src/temp.c:217 chain[0] sen[0] - Lost, no updates for 10 sec" so "chain[0] - Shutting down the chain". Then the machine would power down by itself and restart again. Then on the third auto-restart, same story as above but then "ERROR: src/power.c:161 Malformed power response"

I have read on multiple posts to ReFlash the machine, and some said to reflash the original firmware. So I tried to update the machine per Bitmain's instructions, to do the Upgrade on the Webrowser System's section. This did not work, it didn't have the correct Signature of course. So I then Flashed with a micro SD card this updated S17+ Bitmain firmware. After that the webrowser Systems page was a hybrid of Bitmain and NiceHash!! Some pages have the Bitmain Logo and some the NiceHash. Some of the functions are Bitmain, and some NiceHash!

https://i.ibb.co/6mRGVS7/IMG-4573.jpg

It was not very functional, I couldn't get some pages to open, like Miner Status,  and would show a 404 Error-Not Found. So I thought a hard reset from the machine's little reset button might do the trick. It reset everything, I needed to reset my mining addresses and wallet and such, but it still remembered the profiles that I had already autotuned on the NiceHash firmware. So I decided to open a new browser, and relog in...It was completely the NiceHash OS!!! But I still have access to the Bitmain hybrid controls in the original browser window. So weird.

So it looks like I did not successfully Flash the machine with the Bitmain Firmware. Any suggestions?

These are the Bitmain files that I put on the microSD: Boot.bin; devicetree.dtb; md5_info; runme.sh; ulmage (exec icon); uramdisk.image.gz; and version.
https://i.ibb.co/K9xN3RC/Bitmain-Files-on-micro-SD-card.png

The files I flashed from NiceHash are: Antminer-S17+-2.0.3-Nicehash.tar.gz; devicetree.dtb; passwd.txt; ulmage; uramdisk.image.gz

Thanks in advance

[mikeywith]

Hi, I have a new-to-me S17+_76. As soon as I got it I Flashed it with a micro SD with NiceHash's Firmware.

That's mistake number one, don't use that firmware.

(I'm not sure how to insert pictures that are not from a website but on my hard drive)

We can't see the image this way, you need to upload it here > https://imgbb.com/ and then copy-paste the link.

It was not very functional, I couldn't get some pages to open, like Miner Status,  and would show a 404 Error-Not Found. So I thought a hard reset from the machine's little reset button might do the trick. It reset everything, I needed to reset my mining addresses and wallet and such, but it still remembered the profiles that I had already autotuned on the NiceHash firmware. So I decided to open a new browser, and relog in...It was completely the NiceHash OS!!! But I still have access to the Bitmain hybrid controls in the original browser window. So weird.

So it looks like I did not successfully Flash the machine with the Bitmain Firmware. Any suggestions?

I'd say you did successfully flash it, but google chrome's cache is annoying, use a different browser or hit ctrl+F5 and your problems will go away for now.

If the flash doesn't fix the chips issues, please post the complete kernel log here, and don't forget to use the code tag

Code:

Kernel log goes here

[ShineOn]

I just logged in on a different computer completely, with safari instead of chrome and it's 100% the NiceHash Dashboard and system (no hybridization issue).

https://i.ibb.co/sQzLJjD/IMG-4583.jpg

So the flash did not take hold. Suggestions? Should I try Flashing with the Bitmain S17+ Original Firmware instead of the Updated Firmware I tried?

Here is the Kernel Log:

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203212K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 26164K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 13124K (cce30000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 3391851457
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID F40DA757-D9DC-4B3D-8286-9EC007A4D1F1, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2305/573, WL threshold: 4096, image sequence number: 530904360
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 3E9C38B1-5AEA-4FD6-850C-698DB389147B, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
random: nonblocking pool is initialized
macb e000b000.ethernet eth0: link down
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)

[mikeywith]

I just logged in on a different computer completely, with safari instead of chrome and it's 100% the NiceHash Dashboard and system (no hybridization issue).

In that case, you either used the wrong files in the Sdcard or the Scard is bad, can you show me what files did you place on the Sdcard you used?

https://ibb.co/8xCzBxR

We still can't see the image, you need to upload it and then copy the image URL not the URL you get in the browser, you need to right-click on the image and then copy the image URL.

[ShineOn]

These are the bitmain files I used:

https://i.ibb.co/K9xN3RC/Screen-Shot-2021-04-19-at-10-51-42-PM.png (I hope that worked this time)

and these are the files I used for NiceHash:
https://i.ibb.co/bbVh6Tw/Screen-Shot-2021-04-19-at-10-52-26-PM.png

[ShineOn]

This is odd. So the screen shots I gave in last post is from my hard drive...the original files that I copy and pasted on to my microSD, but these are the actual files on my microSD. It somehow converted two of them in to executable files!

https://i.ibb.co/1qhPQTN/Screen-Shot-2021-04-19-at-11-37-14-PM.png

Looks like those 2 files do not have extensions on them, just the file name and no ".txt"

So if I change these file names to  "version.txt" and "md5_info.txt" do you think that would fix the issue?

Thanks for your help in this!

[ShineOn]

Here is more detail:

This is the original file downloaded from the Bitmain Website: "Antminer-S17+-user-OM-202006021031-sig_5968.tar.gz"

https://i.ibb.co/1ny70JG/Screen-Shot-2021-04-20-at-1-29-12-PM.png

I double clicked this and It created a folder. I opened this folder and these are the contents of that folder:
"cert.pem
cert.pem.sig
fw.tar.gz
fw.tar.gz.sig
runme.sh
runme.sh.sig
version_number  (note, not extension on this file, so creates an excutable file on the SD card)

Here are the files on my Hard Drive
https://i.ibb.co/QCVHJGv/Screen-Shot-2021-04-20-at-1-29-41-PM.png

These are the same files when transfered to my SD card:
https://i.ibb.co/Lzdh55m/Screen-Shot-2021-04-20-at-1-48-18-PM.png

I just tried to flash this on to the machine but it does not seem to be working. I turned power off to machine, installed the microSD card with these files on it, powered the machine back on, the Red (fault) and Green (normal) lights are on solid, It's been running for 20 minutes not and no blinking lights. I just took it out and no change. Still NiceHash OS.

When I click on "fw.tar.gz" a file appears and these are the contents of that file. These are the ones that I posted earlier with 2 files that don't have extensions so show up at excutable. I also tried to flash this and it created a hybrid OS at first but then ultimately when i opened a new browser it was still NiceHash.
"BOOT.bin
devicetree.dtb
md5_info
runme.sh
uImage
uramdisk.image.gz
version"

https://i.ibb.co/1qhPQTN/Screen-Shot-2021-04-19-at-11-37-14-PM.png

Your suggestions?

[mikeywith]

These are the bitmain files I used:

(I hope that worked this time)

The reason why I asked you to show me the files you used is that I thought you could be using the wrong files, which seems like it, here is the correct list of files that has to be on the main directory of the Sdcard.



Download it from here > https://file12.bitmain.com/shop-product/firmware/adfcd6b0-88a0-4cbc-ac17-1bace3991b03/2020/09/27/10/SD_S17%2B.rar

The process is simple.

1- Format the Sdcard using FAT32
2- Unzip the file I put the link to and copy-paste the files inside it to the Sdcard

[ShineOn]

Thanks for the clarity. So while I was waiting for your reply I found the instructions on how to revert the machine to the original firmware version. There is a IP Report button on the machine that does this. It seems to have worked. The Miner Status looks exactly like the what the seller sent me before sending me the unit. There is a newer firmware that I can upgrade to if you suggest that.

It did not fix the issues with my two other boards though 

Here is the Kernel Log.

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203432K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25944K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12904K (cce67000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 3391851457
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID F40DA757-D9DC-4B3D-8286-9EC007A4D1F1, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2307/573, WL threshold: 4096, image sequence number: 530904360
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 3E9C38B1-5AEA-4FD6-850C-698DB389147B, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-04-22 18:37:45 driver-btm-api.c:779:init_freq_mode: This is scan-user version
2021-04-22 18:37:45 driver-btm-api.c:2451:bitmain_soc_init: opt_multi_version     = 1
2021-04-22 18:37:45 driver-btm-api.c:2452:bitmain_soc_init: opt_bitmain_ab        = 1
2021-04-22 18:37:45 driver-btm-api.c:2453:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-04-22 18:37:45 driver-btm-api.c:2454:bitmain_soc_init: Miner compile time: Tue Jun  2 10:31:07 CST 2020 type: Antminer S17+
2021-04-22 18:37:45 driver-btm-api.c:2455:bitmain_soc_init: commit version: 1ca50a5 2020-06-01 18:51:22, build by: lol 2020-06-02 10:37:21
2021-04-22 18:37:45 driver-btm-api.c:2083:show_sn: len:16, 8158448675104814
2021-04-22 18:37:45 driver-btm-api.c:2461:bitmain_soc_init: show sn return 1
2021-04-22 18:37:45 driver-btm-api.c:2103:handle_sn_for_factory_mode: show sn return 1
2021-04-22 18:37:45 driver-btm-api.c:2141:handle_sn_for_factory_mode: read sn success, 8158448675104814
2021-04-22 18:37:45 fan.c:284:front_fan_power_on: Note: front fan is power on!
2021-04-22 18:37:45 fan.c:296:rear_fan_power_on: Note: rear fan is power on!
2021-04-22 18:37:45 driver-btm-api.c:1314:miner_device_init: Detect 256MB control board of XILINX
2021-04-22 18:37:45 driver-btm-api.c:1255:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-04-22 18:37:51 driver-btm-api.c:1239:init_miner_version: miner ID : 8158448675104814
2021-04-22 18:37:51 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-04-22 18:37:56 driver-btm-api.c:837:get_product_id: product_id[0] = 0
2021-04-22 18:37:56 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-04-22 18:37:56 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-04-22 18:37:56 driver-btm-api.c:2234:update_conf_by_power_feedback: Power feedback is disabled
2021-04-22 18:37:56 driver-btm-api.c:2202:get_calibration_voltage: calibration voltage flag is error data.
2021-04-22 18:37:56 driver-btm-api.c:2268:update_conf_by_power_feedback: Note: no calibration voltage, default diff = 0
2021-04-22 18:37:56 frequency.c:1457:adjust_higer_max_vol_table: adjust_higer_max_vol_table, adjust_vol = 0
2021-04-22 18:37:56 thread.c:1363:create_read_nonce_reg_thread: create thread
2021-04-22 18:38:02 driver-btm-api.c:1239:init_miner_version: miner ID : 8158448675104814
2021-04-22 18:38:02 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-04-22 18:38:07 driver-btm-api.c:837:get_product_id: product_id[0] = 0
2021-04-22 18:38:07 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-04-22 18:38:07 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-04-22 18:38:07 driver-btm-api.c:792:_set_project_type: project:0
2021-04-22 18:38:07 driver-btm-api.c:813:_set_project_type: Project type: Antminer S17+
2021-04-22 18:38:07 driver-btm-api.c:824:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-04-22 18:38:07 driver-btm-api.c:825:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-04-22 18:38:07 driver-btm-api.c:824:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-04-22 18:38:07 driver-btm-api.c:825:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-04-22 18:38:07 driver-btm-api.c:824:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-04-22 18:38:07 driver-btm-api.c:825:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-04-22 18:38:09 driver-btm-api.c:2372:bitmain_board_init: Fan check passed.
2021-04-22 18:38:10 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-04-22 18:38:13 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0x88
2021-04-22 18:38:14 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-04-22 18:38:16 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
2021-04-22 18:38:17 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-04-22 18:38:19 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2021-04-22 18:38:19 thread.c:1358:create_pic_heart_beat_thread: create thread
2021-04-22 18:38:19 power_api.c:213:power_init: Power init:
2021-04-22 18:38:19 power_api.c:214:power_init: current_voltage_raw = 0
2021-04-22 18:38:19 power_api.c:215:power_init: highest_voltage_raw = 2100
2021-04-22 18:38:19 power_api.c:216:power_init: working_voltage_raw = 1950
2021-04-22 18:38:19 power_api.c:217:power_init: higher_voltage_raw  = 2040
2021-04-22 18:38:19 power_api.c:218:power_init: check_asic_voltage_raw  = 2100
2021-04-22 18:38:19 driver-btm-api.c:2382:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-04-22 18:38:19 power_api.c:186:power_off: init gpio907
2021-04-22 18:38:51 power_api.c:324:set_to_highest_voltage_by_steps: Set to voltage raw 2100, step by step.
2021-04-22 18:39:17 power_api.c:85:check_voltage_multi: retry time: 0
2021-04-22 18:39:18 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.091969
2021-04-22 18:39:19 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.141192
2021-04-22 18:39:20 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.072727
2021-04-22 18:39:20 power_api.c:53:_get_avg_voltage: average_voltage = 21.101963
2021-04-22 18:39:20 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.10, check voltage passed.
2021-04-22 18:39:20 uart.c:72:set_baud: set fpga_baud to 115200
2021-04-22 18:39:31 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 65 asic, times 0
2021-04-22 18:39:42 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 0
2021-04-22 18:39:52 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 1
2021-04-22 18:40:03 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 2
2021-04-22 18:40:03 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2100
chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-04-22 18:40:12 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 3
2021-04-22 18:40:12 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2050
2021-04-22 18:40:12 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2050, step by step.
2021-04-22 18:40:15 power_api.c:85:check_voltage_multi: retry time: 0
2021-04-22 18:40:17 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.521964
2021-04-22 18:40:18 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.597671
2021-04-22 18:40:19 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.579220
2021-04-22 18:40:19 power_api.c:53:_get_avg_voltage: average_voltage = 20.566285
2021-04-22 18:40:19 power_api.c:71:check_voltage: target_vol = 20.50, actural_vol = 20.57, check voltage passed.
chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-04-22 18:40:28 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 4
2021-04-22 18:40:28 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2000
2021-04-22 18:40:28 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2000, step by step.
2021-04-22 18:40:31 power_api.c:85:check_voltage_multi: retry time: 0
2021-04-22 18:40:32 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.056921
2021-04-22 18:40:33 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.106080
2021-04-22 18:40:34 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.085714
2021-04-22 18:40:34 power_api.c:53:_get_avg_voltage: average_voltage = 20.082905
2021-04-22 18:40:34 power_api.c:71:check_voltage: target_vol = 20.00, actural_vol = 20.08, check voltage passed.
chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-04-22 18:40:43 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 5
2021-04-22 18:40:43 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2100
2021-04-22 18:40:43 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2100, step by step.
2021-04-22 18:40:48 power_api.c:85:check_voltage_multi: retry time: 0
2021-04-22 18:40:50 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.040104
2021-04-22 18:40:51 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.089263
2021-04-22 18:40:52 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.072727
2021-04-22 18:40:52 power_api.c:53:_get_avg_voltage: average_voltage = 21.067364
2021-04-22 18:40:52 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.07, check voltage passed.
2021-04-22 18:40:52 driver-btm-api.c:1193:check_asic_number: Chain 1 only find 0 asic, will power off hash board 1
2021-04-22 18:40:53 driver-btm-api.c:1195:check_asic_number: Chain 1 voltage: an0 = 2.767742, an2 2.767742, an6 2.493548.
2021-04-22 18:41:05 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[2]: find 65 asic, times 0
2021-04-22 18:41:11 driver-hash-chip.c:266:set_uart_relay: set uart relay to 0x330003
2021-04-22 18:41:11 driver-btm-api.c:435:set_order_clock: chain[0]: set order clock, stragegy 3
2021-04-22 18:41:11 driver-btm-api.c:435:set_order_clock: chain[2]: set order clock, stragegy 3
2021-04-22 18:41:11 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
2021-04-22 18:41:11 driver-btm-api.c:1892:check_clock_counter: freq 50 clock_counter_limit 6
2021-04-22 18:41:14 register.c:1572:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 9, core = 0, found 0, clock counter 0x00000000
2021-04-22 18:41:14 driver-btm-api.c:2404:bitmain_board_init: clock counter status was not good. Try reset.
2021-04-22 18:41:14 voltage[0] = 1940
2021-04-22 18:41:14 voltage[2] = 1940
2021-04-22 18:41:14 power_api.c:226:set_working_voltage_raw: working_voltage_raw = 1940
2021-04-22 18:41:15 temperature.c:340:calibrate_temp_sensor_one_chain: chain 0 temp sensor NCT218
2021-04-22 18:41:17 temperature.c:340:calibrate_temp_sensor_one_chain: chain 2 temp sensor NCT218
2021-04-22 18:41:17 uart.c:72:set_baud: set fpga_baud to 12000000
2021-04-22 18:41:17 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:18 driver-btm-api.c:293:check_bringup_temp: Bring up temperature is 23
2021-04-22 18:41:18 thread.c:1378:create_check_miner_status_thread: create thread
2021-04-22 18:41:18 thread.c:1368:create_show_miner_status_thread: create thread
2021-04-22 18:41:18 thread.c:1348:create_temperature_monitor_thread: create thread
2021-04-22 18:41:18 frequency.c:514:check_bringup_temp_dec_freq: dec freq = 0 when bringup temp = 23 dec_freq_index=0
2021-04-22 18:41:18 freq_tuning.c:183:freq_tuning_get_max_freq: Max freq of tuning is 650
2021-04-22 18:41:18 driver-btm-api.c:1765:send_null_work: [DEBUG] Send null work.
2021-04-22 18:41:18 thread.c:1338:create_asic_status_monitor_thread: create thread
2021-04-22 18:41:18 frequency.c:1110:inc_freq_with_fixed_vco: chain = 255, freq = 590, is_higher_voltage = true
2021-04-22 18:41:18 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:20 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:22 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:23 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:25 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:27 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:29 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:31 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:33 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:35 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:37 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:39 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:41 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:42 thread.c:1273:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 11, require 65, failed times 1: ooooo ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2021-04-22 18:41:42 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-04-22 18:41:42 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:44 thread.c:1293:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 0 times.
2021-04-22 18:41:44 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:46 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:48 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-04-22 18:41:48 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:50 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-04-22 18:41:50 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:52 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-04-22 18:41:52 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:54 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-04-22 18:41:54 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:56 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-04-22 18:41:56 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:58 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-04-22 18:41:58 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:41:59 thread.c:1273:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 11, require 65, failed times 1: ooooo ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2021-04-22 18:42:00 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 14, reg = 0
2021-04-22 18:42:01 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 14, reg = 1
2021-04-22 18:42:01 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-04-22 18:42:01 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-04-22 18:42:01 thread.c:1293:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 0 times.
2021-04-22 18:42:01 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2021-04-22 18:42:01 thread.c:1273:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 11, require 65, failed times 1: ooooo ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2021-04-22 18:42:01 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2021-04-22 18:42:02 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0
2021-04-22 18:42:02 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
2021-04-22 18:42:03 temperature.c:875:get_temp_info: ERROR: chain 0 can get NONE temp info or temp value abnormal, power it off 
2021-04-22 18:42:03 thread.c:1293:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 1 times.
2021-04-22 18:42:03 thread.c:1265:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 0, require 65, failed times 1
2021-04-22 18:42:06 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2090, step by step.
2021-04-22 18:42:08 power_api.c:85:check_voltage_multi: retry time: 0
2021-04-22 18:42:09 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.895078
2021-04-22 18:42:09 power_api.c:53:_get_avg_voltage: average_voltage = 20.895078
2021-04-22 18:42:09 power_api.c:71:check_voltage: target_vol = 20.90, actural_vol = 20.90, check voltage passed.
2021-04-22 18:45:44 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2080, step by step.
2021-04-22 18:45:46 power_api.c:85:check_voltage_multi: retry time: 0
2021-04-22 18:45:47 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.772021
2021-04-22 18:45:47 power_api.c:53:_get_avg_voltage: average_voltage = 20.772021
2021-04-22 18:45:47 power_api.c:71:check_voltage: target_vol = 20.80, actural_vol = 20.77, check voltage passed.
2021-04-22 18:48:11 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2020, step by step.
2021-04-22 18:48:14 power_api.c:85:check_voltage_multi: retry time: 0
2021-04-22 18:48:16 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.205959
2021-04-22 18:48:16 power_api.c:53:_get_avg_voltage: average_voltage = 20.205959
2021-04-22 18:48:16 power_api.c:71:check_voltage: target_vol = 20.20, actural_vol = 20.21, check voltage passed.
2021-04-22 18:48:16 frequency.c:1181:inc_asic_diff_freq_by_steps: chain = 2, start = 590, freq_step = 5
2021-04-22 18:48:20 driver-btm-api.c:765:set_timeout: freq = 620, percent = 90, hcn = 44236, timeout = 71
2021-04-22 18:48:20 power_api.c:310:set_to_working_voltage_by_steps: Set to voltage raw 1940, step by step.
2021-04-22 18:48:23 power_api.c:85:check_voltage_multi: retry time: 0
2021-04-22 18:48:24 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 19.418937
2021-04-22 18:48:24 power_api.c:53:_get_avg_voltage: average_voltage = 19.418937
2021-04-22 18:48:24 power_api.c:71:check_voltage: target_vol = 19.40, actural_vol = 19.42, check voltage passed.
2021-04-22 18:48:24 thread.c:1373:create_check_system_status_thread: create thread
2021-04-22 18:48:25 driver-btm-api.c:2618:bitmain_soc_init: Init done!
2021-04-22 18:48:25 driver-btm-api.c:222:set_miner_status: STATUS_INIT
2021-04-22 18:48:29 driver-btm-api.c:222:set_miner_status: STATUS_OKAY
2021-04-22 18:48:30 frequency.c:205:get_ideal_hash_rate_GH: ideal_hash_rate = 25808
2021-04-22 18:48:30 frequency.c:223:get_sale_hash_rate_GH: sale_hash_rate = 25000
2021-04-22 18:48:34 driver-btm-api.c:1496:dhash_chip_send_job: Version num 4.
2021-04-22 18:48:34 driver-btm-api.c:1644:dhash_chip_send_job: stime.tv_sec 1619117314, block_ntime 1619117275
2021-04-22 19:02:26 driver-btm-api.c:222:set_miner_status: WARN_NET_LOST
2021-04-22 19:03:07 driver-btm-api.c:222:set_miner_status: STATUS_OKAY
2021-04-22 19:09:33 driver-btm-api.c:222:set_miner_status: WARN_NET_LOST
2021-04-22 19:09:45 driver-btm-api.c:222:set_miner_status: STATUS_OKAY
2021-04-22 19:18:35 thread.c:259:calc_hashrate_avg: avg rate is 26373.61 in 29 mins
2021-04-22 19:18:35 temperature.c:516:temp_statistics_show:   pcb temp 39~64  chip temp 61~80
2021-04-22 19:19:01 driver-btm-api.c:222:set_miner_status: WARN_NET_LOST
2021-04-22 19:19:04 driver-btm-api.c:222:set_miner_status: STATUS_OKAY

[mikeywith]

Ok so the summary is

Chain 0 finds 65 asic but has a problem with the temp sensor
chain 1 finds 0 asic
chain 2 works just fine

Can you make sure that all the PSU screws going into the hash boards are tightened? also, check the ribbon cables from the control board to the 3 hash boards, swap the ribbon cable from chain 2 to the other two hash boards to confirm the problem isn't the cable.

You also seem to have a network related problem

Code:

2021-04-22 19:19:01 driver-btm-api.c:222:set_miner_status: WARN_NET_LOST

Try using a different network cable to troubleshoot this matter.

[ShineOn]

I was able to try your suggestions. No gross changes to the situation. I did change the ethernet cord and that fixed the network stability, thank you! I made sure the screws were tight to the hash boards...they were. I switched the ribbon for Chain 2 (working board) to Chain 1. Chain 0 continues to initially register chips and then temp sensors become an issue. (I did not switch the ribbon because that ribbon is much longer than the other two. I can swap the board locations though to test the ribbon if you think that would be helpful.)

 I reset it twice with this configuration and these are the Kernel Logs for each.  

Thank you for your continued support in this!

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203432K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25944K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12904K (cce67000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 3391851457
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID F40DA757-D9DC-4B3D-8286-9EC007A4D1F1, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2307/591, WL threshold: 4096, image sequence number: 530904360
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 3E9C38B1-5AEA-4FD6-850C-698DB389147B, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-05-17 20:20:46 driver-btm-api.c:779:init_freq_mode: This is scan-user version
2021-05-17 20:20:46 driver-btm-api.c:2451:bitmain_soc_init: opt_multi_version     = 1
2021-05-17 20:20:46 driver-btm-api.c:2452:bitmain_soc_init: opt_bitmain_ab        = 1
2021-05-17 20:20:46 driver-btm-api.c:2453:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-05-17 20:20:46 driver-btm-api.c:2454:bitmain_soc_init: Miner compile time: Tue Jun  2 10:31:07 CST 2020 type: Antminer S17+
2021-05-17 20:20:46 driver-btm-api.c:2455:bitmain_soc_init: commit version: 1ca50a5 2020-06-01 18:51:22, build by: lol 2020-06-02 10:37:21
2021-05-17 20:20:46 driver-btm-api.c:2083:show_sn: len:16, 8158448675104814
2021-05-17 20:20:46 driver-btm-api.c:2461:bitmain_soc_init: show sn return 1
2021-05-17 20:20:46 driver-btm-api.c:2103:handle_sn_for_factory_mode: show sn return 1
2021-05-17 20:20:46 driver-btm-api.c:2141:handle_sn_for_factory_mode: read sn success, 8158448675104814
2021-05-17 20:20:46 fan.c:284:front_fan_power_on: Note: front fan is power on!
2021-05-17 20:20:46 fan.c:296:rear_fan_power_on: Note: rear fan is power on!
2021-05-17 20:20:46 driver-btm-api.c:1314:miner_device_init: Detect 256MB control board of XILINX
2021-05-17 20:20:46 driver-btm-api.c:1255:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-05-17 20:20:52 driver-btm-api.c:1239:init_miner_version: miner ID : 8158448675104814
2021-05-17 20:20:52 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-05-17 20:20:58 driver-btm-api.c:837:get_product_id: product_id[0] = 0
2021-05-17 20:20:58 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-05-17 20:20:58 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-05-17 20:20:58 driver-btm-api.c:2234:update_conf_by_power_feedback: Power feedback is disabled
2021-05-17 20:20:58 driver-btm-api.c:2202:get_calibration_voltage: calibration voltage flag is error data.
2021-05-17 20:20:58 driver-btm-api.c:2268:update_conf_by_power_feedback: Note: no calibration voltage, default diff = 0
2021-05-17 20:20:58 frequency.c:1457:adjust_higer_max_vol_table: adjust_higer_max_vol_table, adjust_vol = 0
2021-05-17 20:20:58 thread.c:1363:create_read_nonce_reg_thread: create thread
2021-05-17 20:21:04 driver-btm-api.c:1239:init_miner_version: miner ID : 8158448675104814
2021-05-17 20:21:04 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-05-17 20:21:09 driver-btm-api.c:837:get_product_id: product_id[0] = 0
2021-05-17 20:21:09 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-05-17 20:21:09 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-05-17 20:21:09 driver-btm-api.c:792:_set_project_type: project:0
2021-05-17 20:21:09 driver-btm-api.c:813:_set_project_type: Project type: Antminer S17+
2021-05-17 20:21:09 driver-btm-api.c:824:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-05-17 20:21:09 driver-btm-api.c:825:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-05-17 20:21:09 driver-btm-api.c:824:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-05-17 20:21:09 driver-btm-api.c:825:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-05-17 20:21:09 driver-btm-api.c:824:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-05-17 20:21:09 driver-btm-api.c:825:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-05-17 20:21:09 driver-btm-api.c:2372:bitmain_board_init: Fan check passed.
2021-05-17 20:21:10 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-05-17 20:21:12 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0x88
2021-05-17 20:21:13 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-05-17 20:21:15 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
2021-05-17 20:21:17 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-05-17 20:21:19 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2021-05-17 20:21:19 thread.c:1358:create_pic_heart_beat_thread: create thread
2021-05-17 20:21:19 power_api.c:213:power_init: Power init:
2021-05-17 20:21:19 power_api.c:214:power_init: current_voltage_raw = 0
2021-05-17 20:21:19 power_api.c:215:power_init: highest_voltage_raw = 2100
2021-05-17 20:21:19 power_api.c:216:power_init: working_voltage_raw = 1950
2021-05-17 20:21:19 power_api.c:217:power_init: higher_voltage_raw  = 2040
2021-05-17 20:21:19 power_api.c:218:power_init: check_asic_voltage_raw  = 2100
2021-05-17 20:21:19 driver-btm-api.c:2382:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-05-17 20:21:19 power_api.c:186:power_off: init gpio907
2021-05-17 20:21:51 power_api.c:324:set_to_highest_voltage_by_steps: Set to voltage raw 2100, step by step.
2021-05-17 20:22:16 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:22:17 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.064683
2021-05-17 20:22:18 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.097402
2021-05-17 20:22:20 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.141192
2021-05-17 20:22:20 power_api.c:53:_get_avg_voltage: average_voltage = 21.101092
2021-05-17 20:22:20 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.10, check voltage passed.
2021-05-17 20:22:20 uart.c:72:set_baud: set fpga_baud to 115200
2021-05-17 20:22:31 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 65 asic, times 0
2021-05-17 20:22:42 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 65 asic, times 0
2021-05-17 20:22:52 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 0
2021-05-17 20:23:03 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 1
2021-05-17 20:23:14 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 2
2021-05-17 20:23:14 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2100
chain 2, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-05-17 20:23:22 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 3
2021-05-17 20:23:22 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2050
2021-05-17 20:23:22 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2050, step by step.
2021-05-17 20:23:26 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:23:27 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.548512
2021-05-17 20:23:28 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.525907
2021-05-17 20:23:29 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.597671
2021-05-17 20:23:29 power_api.c:53:_get_avg_voltage: average_voltage = 20.557364
2021-05-17 20:23:29 power_api.c:71:check_voltage: target_vol = 20.50, actural_vol = 20.56, check voltage passed.
chain 2, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-05-17 20:23:38 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 4
2021-05-17 20:23:38 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2000
2021-05-17 20:23:38 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2000, step by step.
2021-05-17 20:23:41 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:23:42 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.032342
2021-05-17 20:23:44 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.033679
2021-05-17 20:23:45 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.106080
2021-05-17 20:23:45 power_api.c:53:_get_avg_voltage: average_voltage = 20.057367
2021-05-17 20:23:45 power_api.c:71:check_voltage: target_vol = 20.00, actural_vol = 20.06, check voltage passed.
chain 2, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-05-17 20:23:53 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 5
2021-05-17 20:23:53 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2100
2021-05-17 20:23:53 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2100, step by step.
2021-05-17 20:23:59 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:24:00 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.015524
2021-05-17 20:24:01 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.018135
2021-05-17 20:24:02 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.089263
2021-05-17 20:24:02 power_api.c:53:_get_avg_voltage: average_voltage = 21.040974
2021-05-17 20:24:02 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.04, check voltage passed.
2021-05-17 20:24:02 driver-btm-api.c:1193:check_asic_number: Chain 2 only find 0 asic, will power off hash board 2
2021-05-17 20:24:03 driver-btm-api.c:1195:check_asic_number: Chain 2 voltage: an0 = 2.764516, an2 2.767742, an6 2.493548.
2021-05-17 20:24:10 driver-hash-chip.c:266:set_uart_relay: set uart relay to 0x330003
2021-05-17 20:24:10 driver-btm-api.c:435:set_order_clock: chain[0]: set order clock, stragegy 3
2021-05-17 20:24:10 driver-btm-api.c:435:set_order_clock: chain[1]: set order clock, stragegy 3
2021-05-17 20:24:11 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
2021-05-17 20:24:11 driver-btm-api.c:1892:check_clock_counter: freq 50 clock_counter_limit 6
2021-05-17 20:24:14 register.c:1572:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 9, core = 0, found 0, clock counter 0x00000000
2021-05-17 20:24:14 driver-btm-api.c:2404:bitmain_board_init: clock counter status was not good. Try reset.
2021-05-17 20:24:14 voltage[0] = 1940
2021-05-17 20:24:14 voltage[1] = 1940
2021-05-17 20:24:14 power_api.c:226:set_working_voltage_raw: working_voltage_raw = 1940
2021-05-17 20:24:15 temperature.c:340:calibrate_temp_sensor_one_chain: chain 0 temp sensor NCT218
2021-05-17 20:24:16 temperature.c:340:calibrate_temp_sensor_one_chain: chain 1 temp sensor NCT218
2021-05-17 20:24:16 uart.c:72:set_baud: set fpga_baud to 12000000
2021-05-17 20:24:17 driver-btm-api.c:293:check_bringup_temp: Bring up temperature is 26
2021-05-17 20:24:17 thread.c:1378:create_check_miner_status_thread: create thread
2021-05-17 20:24:17 thread.c:1368:create_show_miner_status_thread: create thread
2021-05-17 20:24:17 thread.c:1348:create_temperature_monitor_thread: create thread
2021-05-17 20:24:17 frequency.c:514:check_bringup_temp_dec_freq: dec freq = 0 when bringup temp = 26 dec_freq_index=0
2021-05-17 20:24:17 freq_tuning.c:183:freq_tuning_get_max_freq: Max freq of tuning is 650
2021-05-17 20:24:17 driver-btm-api.c:1765:send_null_work: [DEBUG] Send null work.
2021-05-17 20:24:17 thread.c:1338:create_asic_status_monitor_thread: create thread
2021-05-17 20:24:17 frequency.c:1110:inc_freq_with_fixed_vco: chain = 255, freq = 590, is_higher_voltage = true
2021-05-17 20:24:20 thread.c:1273:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 48, require 65, failed times 1: ooooo ooooo oxxox ooooo ooooo ooooo ooooo ooooo ooooo ooooo oxxxx xxxxx xxxxx
2021-05-17 20:24:21 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 14, reg = 0
2021-05-17 20:24:21 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-05-17 20:24:21 thread.c:1293:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 0 times.
2021-05-17 20:24:21 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-05-17 20:24:22 thread.c:1273:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 63, require 65, failed times 1: ooooo ooooo oxxoo ooooo ooooo ooooo ooooo ooooo ooooo ooooo ooooo ooooo ooooo
2021-05-17 20:24:23 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-05-17 20:24:23 thread.c:1293:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 1 times.
2021-05-17 20:24:24 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2021-05-17 20:24:24 thread.c:1273:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 11, require 65, failed times 1: ooooo ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2021-05-17 20:24:24 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2021-05-17 20:24:24 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0
2021-05-17 20:24:25 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
2021-05-17 20:24:25 thread.c:1293:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 2 times.
2021-05-17 20:24:26 thread.c:1273:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 11, require 65, failed times 1: ooooo ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2021-05-17 20:24:27 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 14, reg = 0
2021-05-17 20:24:27 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 14, reg = 1
2021-05-17 20:24:27 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2021-05-17 20:24:27 thread.c:1293:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 3 times.
2021-05-17 20:24:28 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2021-05-17 20:24:28 thread.c:1273:asic_status_monitor_thread: ERROR: chain 0 get hashrate_reg_counter 11, require 65, failed times 1: ooooo ooooo oxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
2021-05-17 20:24:28 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0
2021-05-17 20:24:29 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
2021-05-17 20:24:29 thread.c:1293:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 4 times.
2021-05-17 20:24:29 thread.c:1297:asic_status_monitor_thread: chain 0 can't get enough hashrate reg val for 5 times, power off.
2021-05-17 20:24:30 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 14, reg = 0
2021-05-17 20:24:31 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 14, reg = 1
2021-05-17 20:24:31 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 0
2021-05-17 20:24:31 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
2021-05-17 20:24:32 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2090, step by step.
2021-05-17 20:24:32 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 0
2021-05-17 20:24:32 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
2021-05-17 20:24:32 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 0
2021-05-17 20:24:33 temperature.c:843:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
2021-05-17 20:24:33 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:24:34 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.895078
2021-05-17 20:24:34 power_api.c:53:_get_avg_voltage: average_voltage = 20.895078
2021-05-17 20:24:34 power_api.c:71:check_voltage: target_vol = 20.90, actural_vol = 20.90, check voltage passed.
2021-05-17 20:24:43 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2100, step by step.
2021-05-17 20:24:45 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:24:46 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.020753
2021-05-17 20:24:46 power_api.c:53:_get_avg_voltage: average_voltage = 21.020753
2021-05-17 20:24:46 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.02, check voltage passed.
2021-05-17 20:24:51 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2090, step by step.
2021-05-17 20:24:52 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:24:54 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.895078
2021-05-17 20:24:54 power_api.c:53:_get_avg_voltage: average_voltage = 20.895078
2021-05-17 20:24:54 power_api.c:71:check_voltage: target_vol = 20.90, actural_vol = 20.90, check voltage passed.
2021-05-17 20:28:49 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2080, step by step.
2021-05-17 20:28:51 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:28:52 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.772021
2021-05-17 20:28:52 power_api.c:53:_get_avg_voltage: average_voltage = 20.772021
2021-05-17 20:28:52 power_api.c:71:check_voltage: target_vol = 20.80, actural_vol = 20.77, check voltage passed.
2021-05-17 20:31:16 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2020, step by step.
2021-05-17 20:31:19 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:31:20 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.205959
2021-05-17 20:31:20 power_api.c:53:_get_avg_voltage: average_voltage = 20.205959
2021-05-17 20:31:20 power_api.c:71:check_voltage: target_vol = 20.20, actural_vol = 20.21, check voltage passed.
2021-05-17 20:31:20 frequency.c:1181:inc_asic_diff_freq_by_steps: chain = 1, start = 590, freq_step = 5
2021-05-17 20:31:24 driver-btm-api.c:765:set_timeout: freq = 620, percent = 90, hcn = 44236, timeout = 71
2021-05-17 20:31:24 power_api.c:310:set_to_working_voltage_by_steps: Set to voltage raw 1940, step by step.
2021-05-17 20:31:28 power_api.c:85:check_voltage_multi: retry time: 0
2021-05-17 20:31:29 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 19.418937
2021-05-17 20:31:29 power_api.c:53:_get_avg_voltage: average_voltage = 19.418937
2021-05-17 20:31:29 power_api.c:71:check_voltage: target_vol = 19.40, actural_vol = 19.42, check voltage passed.
2021-05-17 20:31:29 thread.c:1373:create_check_system_status_thread: create thread
2021-05-17 20:31:29 driver-btm-api.c:2618:bitmain_soc_init: Init done!
2021-05-17 20:31:29 driver-btm-api.c:222:set_miner_status: STATUS_INIT
2021-05-17 20:31:35 driver-btm-api.c:222:set_miner_status: STATUS_OKAY
2021-05-17 20:31:36 frequency.c:205:get_ideal_hash_rate_GH: ideal_hash_rate = 25808
2021-05-17 20:31:36 frequency.c:223:get_sale_hash_rate_GH: sale_hash_rate = 25000
2021-05-17 20:31:39 driver-btm-api.c:1496:dhash_chip_send_job: Version num 4.
2021-05-17 20:31:39 driver-btm-api.c:1644:dhash_chip_send_job: stime.tv_sec 1621283499, block_ntime 1621283495

[mikeywith]

Well that's an improvement, you went from a complete dead miner to 1/3 of the total hashrate

2021-05-17 20:22:31 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 65 asic, times 0
2021-05-17 20:22:42 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 65 asic, times 0
2021-05-17 20:22:52 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[2]: find 0 asic, times 0

Chain 2 is likely dead and it is not much you can do about it, chain 0 shows all 65 Asics but has a temp-sensor error, the temp-sensor error is mostly not due to a temp-sensor but rather a bad chip or a bad PSU, the same thing could apply for chain 2 since now chain 1 is hashing well, we know the PSU is good for at least 1 hash board, what you should do is unplug chain 0 and 1 and run chain 2 only, then unplug chain 1 and 2 and run chain 0 only, this will ensure that the issue isn't PSU related.