S19j Pro 104th chips state is "normal" but wont hash???

[mikeywith]

I pulled out the two good boards and now its telling me "No data yet! Data is currently unavailable".

This could very well be an EPROM related issue, it would have been very helpful if you were able to install custom firmware on this type of control board, there is probably a way to get in using SSH or something else, I'd try to contact BrianOS and Vnish folks (AwsomeMiner to ASIC.to) and ask if they have a way to burn their firmware on this weird control board.

Custom firmware ignores that voltage setting stored in the EPROM and can many times fix such issues, if there is no option, you are going to need a pro to fix it, they will probably start by copying the hex from a good board to the bad one.

[1714976809]

1714976809

[1714976809]

1714976809

[1714976809]

1714976809

[1714976809]

1714976809

[deafgoose]

ARE YOU USA BASED?

There are a few good repair guys that can turn your gear around fast.

If you deal directly with Bitmain they can be very slow.

You end up with all three boards turned off for a month or more.

Nope, Canada.

UPDATE: All 3 hash boards stopped working today. WTF?

Maybe now somebody will see something in my logs? I would be so grateful to anyone that could shine some light on this issue.

THANK-YOU!!!!

Code:

[    0.000000@0] Booting Linux on physical CPU 0x0
[    0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Mon Dec 26 17:29:52 CST 2022
[    0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[    0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[    0.000000@0] bootconsole [aml_uart0] enabled
[    0.000000@0] efi: Getting EFI parameters from FDT:
[    0.000000@0] efi: UEFI not found.
[    0.000000@0] 	07400000 - 07500000,     1024 KB, ramoops@0x07400000
[    0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[    0.000000@0] 	05000000 - 05400000,     4096 KB, linux,secmon
[    0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
[    0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
[    0.000000@0] cma: Reserved 16 MiB at 0x000000000f000000
[    0.000000@0] On node 0 totalpages: 65536
[    0.000000@0]   DMA zone: 1024 pages used for memmap
[    0.000000@0]   DMA zone: 0 pages reserved
[    0.000000@0]   DMA zone: 65536 pages, LIFO batch:15
[    0.000000@0] psci: probing for conduit method from DT.
[    0.000000@0] psci: PSCIv1.0 detected in firmware.
[    0.000000@0] psci: Using standard PSCI v0.2 function IDs
[    0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000@0] psci: SMC Calling Convention v1.1
[    0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00ef53000 s64536 r8192 d29672 u102400
[    0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096
[    0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000@0] Detected VIPT I-cache on CPU0
[    0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64512
[    0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
[    0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[    0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.000000@0] Memory: 211688K/262144K available (8764K kernel code, 1194K rwdata, 2424K rodata, 3648K init, 1017K bss, 29976K reserved, 20480K cma-reserved)
[    0.000000@0] Virtual kernel memory layout:
[    0.000000@0]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000@0]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000@0]       .text : 0xffffff8009080000 - 0xffffff8009910000   (  8768 KB)
[    0.000000@0]     .rodata : 0xffffff8009910000 - 0xffffff8009b80000   (  2496 KB)
[    0.000000@0]       .init : 0xffffff8009b80000 - 0xffffff8009f10000   (  3648 KB)
[    0.000000@0]       .data : 0xffffff8009f10000 - 0xffffff800a03aa00   (  1195 KB)
[    0.000000@0]        .bss : 0xffffff800a03aa00 - 0xffffff800a139034   (  1018 KB)
[    0.000000@0]     fixed   : 0xffffffbefe7fb000 - 0xffffffbefec00000   (  4116 KB)
[    0.000000@0]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000@0]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000@0]               0xffffffbf00000000 - 0xffffffbf00400000   (     4 MB actual)
[    0.000000@0]     memory  : 0xffffffc000000000 - 0xffffffc010000000   (   256 MB)
[    0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000@0] Preemptible hierarchical RCU implementation.
[    0.000000@0] 	Build-time adjustment of leaf fanout to 64.
[    0.000000@0] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000@0] NR_IRQS:64 nr_irqs:64 0
[    0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    0.000000@0] axg_aoclkc_init: register ao clk ok!
[    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[    0.000000@0] axg_amlogic_init_media: register meson media clk
[    0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[    0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[    0.000000@0] axg_clkc_init initialization complete
[    0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008251@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[    0.016903@0] Console: colour dummy device 80x25
[    0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.031586@0] pid_max: default: 32768 minimum: 301
[    0.036437@0] thread_stack_cache_init, vmap:ffffffc00e5af600, bitmap:ffffffc00e5a3000, cache page:e5e0
[    0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00e5d94c0, addr:ffffff8020000000, size:20001000
[    0.056005@0] cpu 0, vmap_stack:[ffffffc00ef5c960-ffffffc00ef60950]
[    0.062304@0] cpu 0, irq_stack: [ffffffc00ef53060-ffffffc00ef57050]
[    0.068604@0] cpu 1, vmap_stack:[ffffffc00ef75960-ffffffc00ef79950]
[    0.074904@0] cpu 1, irq_stack: [ffffffc00ef6c060-ffffffc00ef70050]
[    0.081204@0] cpu 2, vmap_stack:[ffffffc00ef8e960-ffffffc00ef92950]
[    0.087503@0] cpu 2, irq_stack: [ffffffc00ef85060-ffffffc00ef89050]
[    0.093803@0] cpu 3, vmap_stack:[ffffffc00efa7960-ffffffc00efab950]
[    0.100103@0] cpu 3, irq_stack: [ffffffc00ef9e060-ffffffc00efa2050]
[    0.106464@0] Security Framework initialized
[    0.110696@0] SELinux:  Initializing.
[    0.114386@0] SELinux:  Starting in permissive mode
[    0.114422@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.121106@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.128833@0] ftrace: allocating 30061 entries in 118 pages
[    0.186737@0] sched-energy: CPU device node has no sched-energy-costs
[    0.187549@0] CPU0: update cpu_capacity 1024
[    0.191876@0] ASID allocator initialised with 32768 entries
[    0.230013@0] secmon: can't fine clear_range
[    0.230217@0] EFI services will not be available.
[    0.233481@0] Meson chip version = RevC (25:C - 23:0)
[    0.267152@1] Detected VIPT I-cache on CPU1
[    0.267212@1] CPU1: update cpu_capacity 1024
[    0.267214@1] CPU1: Booted secondary processor [410fd034]
[    0.295218@2] Detected VIPT I-cache on CPU2
[    0.295272@2] CPU2: update cpu_capacity 1024
[    0.295274@2] CPU2: Booted secondary processor [410fd034]
[    0.323277@3] Detected VIPT I-cache on CPU3
[    0.323326@3] CPU3: update cpu_capacity 1024
[    0.323328@3] CPU3: Booted secondary processor [410fd034]
[    0.323414@0] Brought up 4 CPUs
[    0.362635@0] SMP: Total of 4 processors activated.
[    0.367544@0] CPU features: detected feature: 32-bit EL0 Support
[    0.373580@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[    0.384130@0] CPU: All CPU(s) started at EL2
[    0.385319@0] alternatives: patching kernel code
[    0.390622@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[    0.397843@0] devtmpfs: initialized
[    0.412826@0] DMI not present or invalid.
[    0.413183@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.421191@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.427773@0] pinctrl core: initialized pinctrl subsystem
[    0.434160@0] NET: Registered protocol family 16
[    0.457724@0] cpuidle: using governor menu
[    0.458208@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[    0.463831@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[    0.471238@0] DMA: preallocated 256 KiB pool for atomic allocations
[    0.477373@0] clkmsr: clkmsr: driver init
[    0.481437@0] aml_watch_point_probe, in, wp:2
[    0.486017@0] pstore: using zlib compression
[    0.490279@0] console [pstore-1] enabled
[    0.493711@0] pstore: Registered ramoops as persistent store backend
[    0.500119@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
[    0.514478@0] aml_iomap: amlogic iomap probe done
[    0.521284@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[    0.523218@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[    0.623488@0] usbcore: registered new interface driver usbfs
[    0.623658@0] usbcore: registered new interface driver hub
[    0.629255@0] usbcore: registered new device driver usb
[    0.634557@0] pps_core: LinuxPPS API ver. 1 registered
[    0.639502@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.648888@0] PTP clock support registered
[    0.653234@0] dmi: Firmware registration failed.
[    0.662031@0] secmon: reserve_mem_size:0x300000
[    0.662208@0] secmon secmon: assigned reserved memory node linux,secmon
[    0.669179@0] secmon: get page:ffffffbf00140000, 5000
[    0.673866@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[    0.682251@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[    0.690135@0] NetLabel: Initializing
[    0.692301@0] NetLabel:  domain hash size = 128
[    0.696886@0] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.702116@0] NetLabel:  unlabeled traffic allowed by default
[    0.708720@0] clocksource: Switched to clocksource arch_sys_counter
[    0.835576@0] VFS: Disk quotas dquot_6.6.0
[    0.835723@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.861760@0] NET: Registered protocol family 2
[    0.862796@0] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.867993@0] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[    0.874685@0] TCP: Hash tables configured (established 2048 bind 2048)
[    0.881251@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.887209@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.893970@0] NET: Registered protocol family 1
[    0.898933@0] RPC: Registered named UNIX socket transport module.
[    0.904357@0] RPC: Registered udp transport module.
[    0.909232@0] RPC: Registered tcp transport module.
[    0.914142@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.923250@0] Unpacking initramfs...
[    1.423727@3] Initramfs unpacking failed: junk in compressed archive
[    1.430557@3] Freeing initrd memory: 6572K
[    1.431427@3] hw perfevents: clusterb_enabled = 0
[    1.433808@3] hw perfevents: cpumasks 0xf, 0x0
[    1.438279@3] hw perfevents: cluster A irq = 7
[    1.442850@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    1.452992@3] audit: initializing netlink subsys (disabled)
[    1.456338@3] audit: type=2000 audit(1.268:1): initialized
[    1.463656@3] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[    1.487455@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.490410@3] NFS: Registering the id_resolver key type
[    1.493169@3] Key type id_resolver registered
[    1.497492@3] Key type id_legacy registered
[    1.502139@3] fuse init (API version 7.26)
[    1.507475@3] SELinux:  Registering netfilter hooks
[    1.513893@3] NET: Registered protocol family 38
[    1.513954@3] Key type asymmetric registered
[    1.517202@3] Asymmetric key parser 'x509' registered
[    1.522670@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.529896@3] io scheduler noop registered (default)
[    1.534946@3] io scheduler deadline registered
[    1.539666@3] io scheduler cfq registered
[    1.560136@0] random: fast init done
[    1.560236@0] random: crng init done
[    1.561690@3] Unable to detect cache hierarchy for CPU 0
[    1.603269@3] loop: module loaded
[    1.604755@3] zram: Added device: zram0
[    1.605167@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.612043@3] libphy: Fixed MDIO Bus: probed
[    1.616605@3] tun: Universal TUN/TAP device driver, 1.6
[    1.621026@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.629273@3]  ee eth reset:Addr = ffffff80081fd008
[    1.636657@3] meson6-dwmac ff3f0000.ethernet: no reset control found
[    1.638689@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
[    1.643929@3]  Ring mode enabled
[    1.647160@3]  DMA HW capability register supported
[    1.651890@3]  Normal descriptors
[    1.655205@3]  RX Checksum Offload Engine supported
[    1.660111@3] 	COE Type 2
[    1.662731@3]  TX Checksum insertion supported
[    1.667193@3]  Wake-Up On Lan supported
[    1.671135@3]  Enable RX Mitigation via HW Watchdog Timer
[    1.684635@3] libphy: stmmac: probed
[    1.684688@3] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
[    1.691108@3] PPP generic driver version 2.4.2
[    1.694120@3] PPP BSD Compression module registered
[    1.698623@3] PPP Deflate Compression module registered
[    1.703884@3] PPP MPPE Compression module registered
[    1.708838@3] NET: Registered protocol family 24
[    1.714332@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.720235@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.727285@3] usbcore: registered new interface driver cdc_acm
[    1.732480@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.740916@3] usbcore: registered new interface driver usbserial
[    1.747574@3] mousedev: PS/2 mouse device common for all mice
[    1.753069@3] usbcore: registered new interface driver xpad
[    1.758444@3] i2c /dev entries driver
[    1.763218@3] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[    1.767445@3] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[    1.778396@3] ff803000.serial: clock gate not found
[    1.779948@3] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000
[    1.787189@3] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart
[    1.802097@3] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[    1.804800@3] console [ttyS0] enabled
[    1.812016@3] bootconsole [aml_uart0] disabled
[    1.821693@2] ff804000.serial: clock gate not found
[    1.825820@2] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000
[    1.832926@2] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart
[    1.843326@1] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000
[    1.849423@1] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart
[    1.859582@3] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000
[    1.865881@3] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart
[    1.876861@2] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000
[    1.886120@2] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port
[    1.892623@2] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080
[    1.907607@2] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40
[    1.911489@2] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40
[    1.923835@2] aml_dma ff63e000.aml_dma: Aml dma
[    1.927005@2] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
[    1.931949@2] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
[    1.938308@2] efusekeynum: 4
[    1.940642@2] efusekeyname:             mac	offset:     0	size:     6
[    1.947086@2] efusekeyname:          mac_bt	offset:     6	size:     6
[    1.953505@2] efusekeyname:        mac_wifi	offset:    12	size:     6
[    1.959906@2] efusekeyname:            usid	offset:    18	size:    16
[    1.966741@1] efuse efuse: probe OK!
[    1.972170@1] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[    1.979424@0] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode 
[    1.984495@0] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[    1.989731@0] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
[    2.036866@0] meson-mmc: meson_mmc_probe() : success!
[    2.037149@0] amlogic mtd driver init
[    2.041183@0] prase_get_dtb_nand_parameter:128,parse dts start
[    2.045933@0] bl mode descrete
[    2.048812@0] fip_copies 4
[    2.051477@0] fip_size 0x200000
[    2.054616@0] nand_clk_ctrl 0xffe07000
[    2.058341@0] prase_get_dtb_nand_parameter:234,parse dts end
[    2.064007@0] nand_clk_ctrl 0xffe07000
[    2.067728@0] nand register base ffffff80083df800, nand clock register ffffff80083e1000
[    2.076538@0] plat->aml_nand_device ffffff800a005c10
[    2.080639@0] m3_nand_probe() aml_nand_device ffffff800a005c10
[    2.086703@0] NAND device id: 2c da 90 95 6 0
[    2.090764@0] NAND device: Manufacturer ID: 
[    2.094830@0]  0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[    2.101873@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[    2.107306@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[    2.112854@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[    2.119099@0] mtd->oobavail: 0x8
[    2.122508@0] aml_nand_init 2119: plat-name:bootloader
[    2.127418@0] Creating 1 MTD partitions on "bootloader":
[    2.132722@0] 0x000000000000-0x000000200000 : "bootloader"
[    2.141587@0] bootloader initialized ok
[    2.141966@0] plat->aml_nand_device ffffff800a005c10
[    2.146951@0] m3_nand_probe() aml_nand_device ffffff800a005c10
[    2.153086@0] NAND device id: 2c da 90 95 6 0
[    2.157063@0] NAND device: Manufacturer ID: 
[    2.161139@0]  0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[    2.168173@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[    2.173614@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[    2.179154@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[    2.185406@0] mtd->oobavail: 0x8
[    2.188861@0] aml_nand_init 2119: plat-name:nandnormal
[    2.193765@0] bbt_start=20
[    2.196381@0] env_start=24
[    2.199095@0] key_start=32
[    2.201774@0] dtb_start=40
[    2.204440@0] ddr_start=44
[    2.207169@0] nbbt: info size=0x800 max_scan_blk=24, start_blk=20
[    2.213641@0] get_free_node 43: bitmap=0
[    2.217114@0] get_free_node 55: bitmap=1
[    2.221206@0] get_free_node 43: bitmap=1
[    2.224913@0] get_free_node 55: bitmap=3
[    2.229005@0] get_free_node 43: bitmap=3
[    2.232695@0] get_free_node 55: bitmap=7
[    2.236597@0] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
[    2.243284@0] nbbt free list:
[    2.246231@0] blockN=21, ec=-1, dirty_flag=0
[    2.250478@0] blockN=22, ec=-1, dirty_flag=0
[    2.254724@0] blockN=23, ec=-1, dirty_flag=0
[    2.258972@0] aml_nand_scan_rsv_info 1141: page_num=1
[    2.264381@0] nbbt valid addr: 280000
[    2.267641@0] aml_nand_bbt_check 1306 bbt is valid, reading.
[    2.273272@0] aml_nand_read_rsv_info:423,read nbbt info at 280000
[    2.279534@0] nenv: info size=0x10000 max_scan_blk=32, start_blk=24
[    2.285962@0] get_free_node 43: bitmap=7
[    2.289480@0] get_free_node 55: bitmap=f
[    2.293571@0] get_free_node 43: bitmap=f
[    2.297280@0] get_free_node 55: bitmap=1f
[    2.301458@0] get_free_node 43: bitmap=1f
[    2.305253@0] get_free_node 55: bitmap=3f
[    2.309431@0] get_free_node 43: bitmap=3f
[    2.313226@0] get_free_node 55: bitmap=7f
[    2.317405@0] get_free_node 43: bitmap=7f
[    2.321199@0] get_free_node 55: bitmap=ff
[    2.325377@0] get_free_node 43: bitmap=ff
[    2.329173@0] get_free_node 55: bitmap=1ff
[    2.333438@0] get_free_node 43: bitmap=1ff
[    2.337320@0] get_free_node 55: bitmap=3ff
[    2.341393@0] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1
[    2.348063@0] nenv free list:
[    2.351011@0] blockN=25, ec=-1, dirty_flag=0
[    2.355257@0] blockN=26, ec=-1, dirty_flag=0
[    2.359504@0] blockN=27, ec=-1, dirty_flag=0
[    2.363751@0] blockN=28, ec=-1, dirty_flag=0
[    2.367997@0] blockN=29, ec=-1, dirty_flag=0
[    2.372244@0] blockN=30, ec=-1, dirty_flag=0
[    2.376491@0] blockN=31, ec=-1, dirty_flag=0
[    2.380738@0] aml_nand_scan_rsv_info 1141: page_num=32
[    2.398000@0] nenv valid addr: 310000
[    2.398034@0] nkey: info size=0x8000 max_scan_blk=40, start_blk=32
[    2.402392@0] get_free_node 43: bitmap=3ff
[    2.406272@0] get_free_node 55: bitmap=7ff
[    2.410537@0] get_free_node 43: bitmap=7ff
[    2.414418@0] get_free_node 55: bitmap=fff
[    2.418683@0] get_free_node 43: bitmap=fff
[    2.422565@0] get_free_node 55: bitmap=1fff
[    2.426917@0] get_free_node 43: bitmap=1fff
[    2.430885@0] get_free_node 55: bitmap=3fff
[    2.435236@0] get_free_node 43: bitmap=3fff
[    2.439205@0] get_free_node 55: bitmap=7fff
[    2.443556@0] get_free_node 43: bitmap=7fff
[    2.447525@0] get_free_node 55: bitmap=ffff
[    2.451876@0] get_free_node 43: bitmap=ffff
[    2.455845@0] get_free_node 55: bitmap=1ffff
[    2.460282@0] get_free_node 43: bitmap=1ffff
[    2.464338@0] get_free_node 55: bitmap=3ffff
[    2.468585@0] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[    2.475255@0] nkey free list:
[    2.478203@0] blockN=32, ec=-1, dirty_flag=0
[    2.482450@0] blockN=33, ec=-1, dirty_flag=0
[    2.486696@0] blockN=34, ec=-1, dirty_flag=0
[    2.490942@0] blockN=35, ec=-1, dirty_flag=0
[    2.495189@0] blockN=36, ec=-1, dirty_flag=0
[    2.499436@0] blockN=37, ec=-1, dirty_flag=0
[    2.503683@0] blockN=38, ec=-1, dirty_flag=0
[    2.507929@0] blockN=39, ec=-1, dirty_flag=0
[    2.512176@0] aml_nand_scan_rsv_info 1141: page_num=16
[    2.517289@0] nkey valid addr: fffffffffffe0000
[    2.521798@0] aml_nand_key_check 1251 NO key exist
[    2.526564@0] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
[    2.533185@0] get_free_node 43: bitmap=3ffff
[    2.537052@0] get_free_node 55: bitmap=7ffff
[    2.541490@0] get_free_node 43: bitmap=7ffff
[    2.545545@0] get_free_node 55: bitmap=fffff
[    2.549983@0] get_free_node 43: bitmap=fffff
[    2.554038@0] get_free_node 55: bitmap=1fffff
[    2.558372@0] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1
[    2.565042@0] ndtb free list:
[    2.567973@0] blockN=41, ec=-1, dirty_flag=0
[    2.572236@0] blockN=42, ec=-1, dirty_flag=0
[    2.576483@0] blockN=43, ec=-1, dirty_flag=0
[    2.580730@0] aml_nand_scan_rsv_info 1141: page_num=64
[    2.598036@0] ndtb valid addr: 500000
[    2.598070@0] nddr: info size=0x20000 max_scan_blk=46, start_blk=44
[    2.602510@0] get_free_node 43: bitmap=1fffff
[    2.606654@0] get_free_node 55: bitmap=3fffff
[    2.611178@0] get_free_node 43: bitmap=3fffff
[    2.615320@0] get_free_node 55: bitmap=7fffff
[    2.619653@0] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[    2.626324@0] nddr free list:
[    2.629271@0] blockN=44, ec=-1, dirty_flag=0
[    2.633518@0] blockN=45, ec=-1, dirty_flag=0
[    2.637765@0] aml_nand_scan_rsv_info 1141: page_num=64
[    2.642878@0] nddr valid addr: fffffffffffe0000
[    2.647385@0] aml_nand_ddr_check 1281 NO ddr exist
[    2.652155@0] tpl: off 8388608, size 8388608
[    2.783826@0] Creating 6 MTD partitions on "nandnormal":
[    2.783873@0] 0x000000800000-0x000001000000 : "tpl"
[    2.795063@1] 0x000001000000-0x000001200000 : "misc"
[    2.798192@2] 0x000001200000-0x000002200000 : "recovery"
[    2.810242@2] 0x000002200000-0x000004200000 : "boot"
[    2.829401@2] 0x000004200000-0x000004700000 : "config"
[    2.834074@2] 0x000004700000-0x000010000000 : "nvdata"
[    2.935098@0] nandnormal initialized ok
[    2.935206@0] aml_ubootenv_init: register env chardev
[    2.938937@0] aml_ubootenv_init: register env chardev OK
[    2.943777@0] amlnf_dtb_init: register dtb cdev
[    2.948751@0] amlnf_dtb_init: register dtd cdev OK
[    2.952948@0] mtd_nand_probe 267 , err = 0
[    2.958073@1] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
[    2.963525@1] input: aml_vkeypad as /devices/platform/rtc/input/input0
[    2.970695@0] unifykey: storage in base: 0xffffffc005000000
[    2.975132@0] unifykey: storage out base: 0xffffffc005040000
[    2.980736@0] unifykey: storage block base: 0xffffffc005080000
[    2.986536@0] unifykey: probe done!
[    2.990733@0] unifykey: no efuse-version set, use default value: -1
[    2.996262@0] unifykey: key unify config unifykey-num is 6
[    3.001791@0] unifykey: key unify fact unifykey-num is 6
[    3.006997@0] unifykey: unifykey_devno: f200000
[    3.012184@0] unifykey: device unifykeys created ok
[    3.016483@0] unifykey: aml_unifykeys_init done!
[    3.021387@0] sysled: module init
[    3.024884@0] meson_wdt ffd0f0d0.watchdog: start watchdog
[    3.029635@0] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
[    3.037067@0] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
[    3.045764@1] dmc_monitor_probe
[    3.051602@1] defendkey defendkey: Reserved memory is not enough!
[    3.052329@1] defendkey: probe of defendkey failed with error -22
[    3.058760@1] GACT probability NOT on
[    3.062087@1] Mirror/redirect action on
[    3.065865@1] u32 classifier
[    3.068680@1]     Actions configured
[    3.072258@1] Netfilter messages via NETLINK v0.30.
[    3.077540@1] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    3.083734@1] ctnetlink v0.93: registering with nfnetlink.
[    3.089610@1] xt_time: kernel timezone is -0000
[    3.093328@1] ipip: IPv4 and MPLS over IPv4 tunneling driver
[    3.099962@1] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.104642@1] arp_tables: arp_tables: (C) 2002 David S. Miller
[    3.110134@1] Initializing XFRM netlink socket
[    3.115657@1] NET: Registered protocol family 10
[    3.121399@1] mip6: Mobile IPv6
[    3.122205@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    3.128182@1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.136144@1] NET: Registered protocol family 17
[    3.138458@1] NET: Registered protocol family 15
[    3.143055@1] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    3.156196@1] l2tp_core: L2TP core driver, V2.0
[    3.160592@1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    3.165510@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[    3.171261@1] l2tp_netlink: L2TP netlink interface
[    3.176070@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[    3.182143@1] l2tp_debugfs: L2TP debugfs support
[    3.186654@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[    3.193315@1] NET: Registered protocol family 35
[    3.198232@1] Key type dns_resolver registered
[    3.202794@1] Registered swp emulation handler
[    3.206696@1] Registered cp15_barrier emulation handler
[    3.211887@1] Registered setend emulation handler
[    3.216630@1] disable EAS feature
[    3.221612@1] registered taskstats version 1
[    3.237799@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
[    3.744209@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.744296@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    3.752579@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010
[    3.761021@3] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
[    3.768494@1] hub 1-0:1.0: USB hub found
[    3.770979@1] hub 1-0:1.0: 1 port detected
[    3.775569@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.780597@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    3.788491@1] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.797981@2] hub 2-0:1.0: USB hub found
[    3.800549@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    3.807903@2] usb usb2: Unsupported the hub
[    3.812636@2] aml_vrtc rtc: setting system clock to 2015-01-01 00:00:08 UTC (1420070408)
[    3.820742@2] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00d173000)
[    3.820820@2] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
[    3.828672@2] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000
[    3.828684@2] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00bb27e00
[    3.929280@2] dwc_otg: Core Release: 3.10a
[    3.929334@2] dwc_otg: Setting default values for core params
[    3.933530@2] dwc_otg: curmode: 0, host_only: 0
[    3.938033@2] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
[    3.950538@2] dwc_otg: Using Buffer DMA mode
[    3.950576@2] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    3.954484@2] dwc_otg: Working on port type = SLAVE
[    3.959341@2] dwc_otg: Dedicated Tx FIFOs mode
[    3.966279@2] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
[    3.973052@2] cpucore_cooling_register, max_cpu_core_num:4
[    3.985266@0] gxbb_pm: enter meson_pm_probe!
[    3.985324@0] no vddio3v3_en pin
[    3.986975@0] pm-meson aml_pm: Can't get switch_clk81
[    3.992074@0] gxbb_pm: meson_pm_probe done
[    3.997041@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[    4.003308@0] Freeing unused kernel memory: 3648K
[    4.017619@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[    4.269025@0] ubi0: attaching mtd5
[    4.287552@0] ubi0: scanning is finished
[    4.292113@3] ubi0: attached mtd5 (name "config", size 5 MiB)
[    4.292242@3] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.299323@3] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.306209@3] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.313321@3] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0
[    4.319381@3] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    4.326757@3] ubi0: max/mean erase counter: 10/5, WL threshold: 4096, image sequence number: 4272682163
[    4.336106@3] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4
[    4.345329@0] ubi0: background thread "ubi_bgt0d" started, PID 1076
[    4.358538@1] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1080
[    4.375136@2] UBIFS (ubi0:0): recovery needed
[    4.426251@0] UBIFS (ubi0:0): recovery completed
[    4.426509@0] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
[    4.433261@0] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    4.443301@0] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[    4.453522@0] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)
[    4.460111@0] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID DF678CD6-72B3-440D-AD49-B5CACA89C146, small LPT model
[    4.484804@0] ubi2: attaching mtd6
[    5.158140@0] ubi2: scanning is finished
[    5.165564@1] ubi2: attached mtd6 (name "nvdata", size 185 MiB)
[    5.165868@1] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    5.172922@1] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    5.179845@1] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
[    5.186950@1] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0
[    5.193186@1] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
[    5.200546@1] ubi2: max/mean erase counter: 6/2, WL threshold: 4096, image sequence number: 3925779084
[    5.209826@1] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4
[    5.219200@3] ubi2: background thread "ubi_bgt2d" started, PID 1087
[    5.232088@2] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1091
[    5.248767@0] UBIFS (ubi2:0): recovery needed
[    5.296598@0] UBIFS (ubi2:0): recovery completed
[    5.296903@0] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data"
[    5.303591@0] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    5.313643@0] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)
[    5.324469@0] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
[    5.331233@0] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID D3E2E49A-3C02-4261-9EEF-3A2DAF328DBD, small LPT model
[    5.551613@3] eth0: device MAC address 02:5a:b9:1d:92:fb
[    5.633822@0] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
[    5.635120@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.886634@0] uart_trans: loading out-of-tree module taints kernel.
[    5.889260@0] register uart_trans chrdev success.
[    5.892442@0] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600
[    5.900442@0] tty port open success [/dev/ttyS3]!
[    5.904869@0] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200
[    5.913386@0] init sucess for tty struct (246:3)  [/dev/ttyS3]
[    5.919339@0] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600
[    5.926993@0] tty port open success [/dev/ttyS2]!
[    5.931635@0] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200
[    5.940103@0] init sucess for tty struct (246:2)  [/dev/ttyS2]
[    5.946228@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
[    5.953877@0] tty port open success [/dev/ttyS1]!
[    5.958524@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
[    5.966946@0] init sucess for tty struct (246:1)  [/dev/ttyS1]
[    5.973018@0] create workqueue success!
[    7.672988@0] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[    7.676278@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   32.284909@1] uart trans dev open.
[   32.285019@1] uart_buf virt addr = 0xffffffc00b1c0000
[   32.287724@1] uart_buf phys addr = 0x0b1c0000
[   32.292108@1] uart_buf pfn       = 0x0000b1c0
[   32.296926@1] uart trans stop send work timer.
[   32.301098@1] uart trans set chain exist bits:0x7.
[   32.305607@1] uart trans set work queue count 768.
[   83.119658@3] uart set baud to: 4098
[   83.119718@3] uart set baud to: 4098
[   83.121230@3] uart set baud to: 4098
[   96.236632@2] uart trans stop send work timer.
[   98.947924@3] uart trans start send work timer.
[  301.722926@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based  firewall rule not found. Use the iptables CT target to attach helpers instead.


===========================================Miner log===========================================
2015-01-01 00:00:15 Open miner sn file /config/sn error
2015-01-01 00:00:15 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :
2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2015-01-01 00:00:16 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2015-01-01 00:00:16 opt_multi_version     = 1
2015-01-01 00:00:16 opt_bitmain_ab        = 1
2015-01-01 00:00:16 mid_auto_gen          = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 0
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0
2015-01-01 00:00:16 start listen on 6060 ...
2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 ==========================capability start==========================
2015-01-01 00:00:21 board num = 3
2015-01-01 00:00:21 board id = 0, chain num = 1
2015-01-01 00:00:21 	chain id = 0
2015-01-01 00:00:21 board id = 1, chain num = 1
2015-01-01 00:00:21 	chain id = 1
2015-01-01 00:00:21 board id = 2, chain num = 1
2015-01-01 00:00:21 	chain id = 2
2015-01-01 00:00:21 ==========================capability end============================
2015-01-01 00:00:21 chain num = 3
2015-01-01 00:00:21 skip loading levels for now
2023-06-16 22:30:25 load chain 0 eeprom data
2023-06-16 22:30:29 load chain 1 eeprom data
2023-06-16 22:30:32 load chain 2 eeprom data
2023-06-16 22:30:32 i2c_sim_init start
2023-06-16 22:30:32 init gpio477
2023-06-16 22:30:32 init gpio476
2023-06-16 22:30:32 i2c_sim_init end
2023-06-16 22:30:33 power open power_version = 0x76
2023-06-16 22:30:36 power is not Calibrated
2023-06-16 22:30:37 miner type: Antminer S19j Pro
2023-06-16 22:30:37 multi machine mode
2023-06-16 22:30:37 load machine BHB42631 conf
2023-06-16 22:30:37 machine : BHB42631 
2023-06-16 22:30:37 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-06-16 22:30:37 abandon mix board!
2023-06-16 22:30:37 abandon mix board!
2023-06-16 22:30:37 fan_eft : 0  fan_pwm : 100
2023-06-16 22:30:37 create thread get_nonce_and_register_thread
2023-06-16 22:30:37 fixed working voltage = 1380
2023-06-16 22:30:37 fixed frequency is 525
2023-06-16 22:30:37 Chain [0] PCB Version: 0x0110
2023-06-16 22:30:37 Chain [0] BOM Version: 0x0010
2023-06-16 22:30:37 Chain [1] PCB Version: 0x0110
2023-06-16 22:30:37 Chain [1] BOM Version: 0x0010
2023-06-16 22:30:37 Chain [2] PCB Version: 0x0110
2023-06-16 22:30:37 Chain [2] BOM Version: 0x0010
2023-06-16 22:30:37 bad chain id = 3
2023-06-16 22:30:37 Fan check passed.
2023-06-16 22:30:37 uart_trans addr:0xf43df000.
2023-06-16 22:30:37 max sensor num = 4
2023-06-16 22:30:37 STATUS_INITED: soc init done!
2023-06-16 22:30:37 temperature_monitor_thread start...
2023-06-16 22:30:40 start to init...
2023-06-16 22:30:40 warning:power is not calibration.
2023-06-16 22:30:41 power type version: 0x0076
2023-06-16 22:30:43 disable power watchdog: 0x0000
2023-06-16 22:30:44 Initializing the power, please wait, this may take up to 2 minutes...
2023-06-16 22:31:15 Slept 30 seconds, diff = 0.
2023-06-16 22:31:19 set_voltage_by_steps to 1500.
2023-06-16 22:31:28 start up min temp by 75a = 24
2023-06-16 22:31:31 Chain[0]: find 126 asic, times 0
2023-06-16 22:31:33 Chain[1]: find 126 asic, times 0
2023-06-16 22:31:35 Chain[2]: find 0 asic, times 0
2023-06-16 22:31:37 Chain[2]: find 0 asic, times 1
2023-06-16 22:31:38 Chain[2]: find 0 asic, times 2
2023-06-16 22:31:38 Chain 2 only find 0 asic, will power off hash board 2
2023-06-16 22:31:38 ERROR_SOC_INIT: soc init failed!
2023-06-16 22:31:38 stop_mining: soc init failed!
2023-06-16 22:31:38 uninit_temp_info
2023-06-16 22:31:38 do not read temp anymore...
2023-06-16 22:31:38 cancel thread
2023-06-16 22:31:38 ****power off hashboard****
2023-06-16 22:31:39 temp monitor thread exit
2023-06-16 22:31:44 Version num 65536
2023-06-16 22:31:44 Mask num 0x1fffe000
2023-06-16 22:31:44 opt_multi_version = 65536, interval timeout = 2945120
2023-06-16 22:31:44 freq = 525, percent = 90, hcn = 4993, timeout = 2945120

[BitMaxz]

Code:

2023-06-16 22:30:37 abandon mix board!
2023-06-16 22:30:37 abandon mix board!

2023-06-16 22:31:31 Chain[0]: find 126 asic, times 0
2023-06-16 22:31:33 Chain[1]: find 126 asic, times 0
2023-06-16 22:31:35 Chain[2]: find 0 asic, times 0
2023-06-16 22:31:37 Chain[2]: find 0 asic, times 1
2023-06-16 22:31:38 Chain[2]: find 0 asic, times 2
2023-06-16 22:31:38 Chain 2 only find 0 asic, will power off hash board 2
2023-06-16 22:31:38 ERROR_SOC_INIT: soc init failed!

The issue from logs still the same as from your previous logs removing the 3rd hashboard and keeping the two hashboards should run normally with decrease hashrate.

As suggested by mikeywith you can try Braiins OS to test if it is just an EEPROM issue but the problem is as you said before that it does not have the SD card slot have you checked the control board inside and maybe the SD card slot is hiding near Ethernet socket or beaglebone ?
Or if does not have an SD slot then your last hope is to use an OTG drive to micro USB to boot Braiins OS in your unit.

[deafgoose]

The issue from logs still the same as from your previous logs removing the 3rd hashboard and keeping the two hashboards should run normally with decrease hashrate.

As suggested by mikeywith you can try Braiins OS to test if it is just an EEPROM issue but the problem is as you said before that it does not have the SD card slot have you checked the control board inside and maybe the SD card slot is hiding near Ethernet socket or beaglebone ?
Or if does not have an SD slot then your last hope is to use an OTG drive to micro USB to boot Braiins OS in your unit.

Don't you find it strange that its defective yet no issue with my logs?

I am very unlucky. I dont have the sd-card version. I will order the adapter and load up Braiins OS and report back.

EDIT: Will this adapter work?
https://www.amazon.ca/Sandisk-SDDD3-016G-G46-Cellphone-Signal-Booster/dp/B01M1272LZ/

[mikeywith]

Wait, the new logs you posted is telling a different story from the one in the op

Code:

2023-06-16 22:31:38 Chain[2]: find 0 asic, times 2
2023-06-16 22:31:38 Chain 2 only find 0 asic, will power off hash 

This shows that the 3rd chain is dead, in the op it was chain 0 ( labeled 1 in the GUI), did you swap these two hashboards?

[BitMaxz]

This shows that the 3rd chain is dead, in the op it was chain 0 ( labeled 1 in the GUI), did you swap these two hashboards?

Yes he did that was my suggestion on my previous post to know if the cable is damaged or the hashboard is dead.

Don't you find it strange that its defective yet no issue with my logs?

I am very unlucky. I dont have the sd-card version. I will order the adapter and load up Braiins OS and report back.

EDIT: Will this adapter work?
https://www.amazon.ca/Sandisk-SDDD3-016G-G46-Cellphone-Signal-Booster/dp/B01M1272LZ/

I don't see any strange logs except on the abandon mix board and 0 ASIC on the 3rd hashboard.
If we see these logs like the Abadon mix board the first thing that comes to my mind like Philipma1957 said that 3rd hashboard might be a replacement board which is why it stop mining due to the EEPROM compatibility issue.

About the OTG SanDisk, that thing might work but I'm not sure if the s19j pro USB port support USB 3.0 and it's a bit expensive why not just buy a Micro USB port to USB female connector which is cheaper if you already have a USB flash drive.

[mikeywith]

But in the first kernel log he posted it was not showing 0 asic for the bad hashboard, which is why we started talking about the EPROM, if shows 0 asic then that is a different story, it is likely the hashboard is dead and needs repair, in other words, it is unlikely to be software related.

[deafgoose]

I got my sd-card adapter. Apparently its USB 3.0 but luckily 3.0 is backwards compatible all the way down to 1.1.

I flashed the image onto the adapter, stuck it in, booted it up and nothing. I go to the ip address and its still the old firmware.

From my understanding, it should have auto-installed after boot-up...

[mikeywith]

I got my sd-card adapter. Apparently its USB 3.0 but luckily 3.0 is backwards compatible all the way down to 1.1.

I flashed the image onto the adapter, stuck it in, booted it up and nothing. I go to the ip address and its still the old firmware.

From my understanding, it should have auto-installed after boot-up...

It could have flashed the firmware but just so happened that it is the same version, to confirm if it went through or not, you would check your pool settings (should go back to default settings) and the miner's ip settings (back to dhcp).

Try BraiinOS, it should boot from the sdcard without flashing to nand.

[BitMaxz]

But in the first kernel log he posted it was not showing 0 asic for the bad hashboard, which is why we started talking about the EPROM, if shows 0 asic then that is a different story, it is likely the hashboard is dead and needs repair, in other words, it is unlikely to be software related.

Opppsss.... that was my mistake I didn't review the previous logs I thought that I saw it on the image but the image only shows that the first hashboard is abnormal.

I got my sd-card adapter. Apparently its USB 3.0 but luckily 3.0 is backwards compatible all the way down to 1.1.

I flashed the image onto the adapter, stuck it in, booted it up and nothing. I go to the ip address and its still the old firmware.

From my understanding, it should have auto-installed after boot-up...

You might did it wrong that is why the version didn't change and sometimes fake SD card have fake voluke that can turn some files corrupted so try to re place a SD card.

Also there is a detailed guide on how to flash this unit through OTG/SD card check this link below

- https://support.bitmain.com/hc/en-us/articles/4404919472281-S19j-S19j-Pro-control-board-program-recovery-SD-card-flashing-

If still didn't work then like other said and my previous post boot it with Braiins OS you can che the guide below how to boot or flash the miner with Braiins.

- https://docs.braiins.com/os/plus-en/Setup/1_quickstart.html#install-braiins-os

[ph0d]

Ok heres some funky for ya's

Tested boards - they seem ok ... as best as I can test them.

Installed braains on this AML s19pro so I have logs from both factory and braains.

Here's the factory:

2023-11-12 09:30:58 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :
2023-11-12 09:30:59 This is fix-freq version
2023-11-12 09:30:59 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2023-11-12 09:30:59 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2023-11-12 09:30:59 opt_multi_version     = 1
2023-11-12 09:30:59 opt_bitmain_ab        = 1
2023-11-12 09:30:59 mid_auto_gen          = 1
2023-11-12 09:30:59 opt_bitmain_work_mode = 0
2023-11-12 09:30:59 port 439 already exported
2023-11-12 09:30:59 port 454 already exported
2023-11-12 09:30:59 port 440 already exported
2023-11-12 09:30:59 port 455 already exported
2023-11-12 09:30:59 port 441 already exported
2023-11-12 09:30:59 port 456 already exported
2023-11-12 09:30:59 port 438 already exported
2023-11-12 09:30:59 port 453 already exported
2023-11-12 09:30:59 port 446 already exported
2023-11-12 09:30:59 port 445 already exported
2023-11-12 09:30:59 Note: front fan is power on!
2023-11-12 09:30:59 Note: rear fan is power on!
2023-11-12 09:30:59 start the http log.
2023-11-12 09:30:59 start listen on 6060 ...
2023-11-12 09:30:59 httpListenThread start ret=0
2023-11-12 09:30:59 bad chain id = 3
2023-11-12 09:31:02 bad chain id = 3
2023-11-12 09:31:04 ==========================capability start==========================
2023-11-12 09:31:04 board num = 3
2023-11-12 09:31:04 board id = 0, chain num = 1
2023-11-12 09:31:04    chain id = 0
2023-11-12 09:31:04 board id = 1, chain num = 1
2023-11-12 09:31:04    chain id = 1
2023-11-12 09:31:04 board id = 2, chain num = 1
2023-11-12 09:31:04    chain id = 2
2023-11-12 09:31:04 ==========================capability end============================
2023-11-12 09:31:04 chain num = 3
2023-11-12 09:31:04 skip loading levels for now
2023-11-12 09:31:08 load chain 0 eeprom data
2023-11-12 09:31:12 load chain 1 eeprom data
2023-11-12 09:31:15 load chain 2 eeprom data
2023-11-12 09:31:15 i2c_sim_init start
2023-11-12 09:31:15 init gpio477
2023-11-12 09:31:15 init gpio476
2023-11-12 09:31:15 i2c_sim_init end
2023-11-12 09:31:16 power open power_version = 0x71
2023-11-12 09:31:22 power is not Calibrated
2023-11-12 09:31:23 miner type: Antminer S19j Pro
2023-11-12 09:31:23 multi machine mode
2023-11-12 09:31:23 load machine BHB42601 conf
2023-11-12 09:31:23 machine : BHB42601
2023-11-12 09:31:23 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-11-12 09:31:23 abandon mix board!
2023-11-12 09:31:23 abandon mix board!
2023-11-12 09:31:23 fan_eft : 1  fan_pwm : 20
2023-11-12 09:31:23 create thread get_nonce_and_register_thread
2023-11-12 09:31:23 fixed working voltage = 1380
2023-11-12 09:31:23 fixed frequency is 545
2023-11-12 09:31:23 Chain

• PCB Version: 0x0130

2023-11-12 09:31:23 Chain

• BOM Version: 0x0010

2023-11-12 09:31:23 Chain [1] PCB Version: 0x0130
2023-11-12 09:31:23 Chain [1] BOM Version: 0x0010
2023-11-12 09:31:23 Chain [2] PCB Version: 0x0130
2023-11-12 09:31:23 Chain [2] BOM Version: 0x0010
2023-11-12 09:31:23 bad chain id = 3
2023-11-12 09:31:23 Fan check passed.
2023-11-12 09:31:23 uart_trans addr:0xf6fbb000.
2023-11-12 09:31:24 chain[0] PIC jump to app
2023-11-12 09:31:25 Check chain[0] PIC fw version=0x89
2023-11-12 09:31:26 chain[1] PIC jump to app
2023-11-12 09:31:28 Check chain[1] PIC fw version=0x89
2023-11-12 09:31:29 chain[2] PIC jump to app
2023-11-12 09:31:30 Check chain[2] PIC fw version=0x89
2023-11-12 09:31:31 create thread pic_heart_beat_thread
2023-11-12 09:31:31 max sensor num = 4
2023-11-12 09:31:31 STATUS_INITED: soc init done!
2023-11-12 09:31:31 temperature_monitor_thread start...
2023-11-12 09:31:34 start to init...
2023-11-12 09:31:34 warning:power is not calibration.
2023-11-12 09:31:35 power type version: 0x0071
2023-11-12 09:31:35 Initializing the power, please wait, this may take up to 2 minutes...
2023-11-12 09:32:06 Slept 30 seconds, diff = 0.
2023-11-12 09:32:07 set_voltage_by_steps to 1500.
2023-11-12 09:32:10 power voltage can not meet the target
2023-11-12 09:32:12 power voltage can not meet the target
2023-11-12 09:32:13 power voltage can not meet the target
2023-11-12 09:32:13 Sweep error string = V:1.
2023-11-12 09:32:13 ERROR_POWER_LOST: get power type version failed!
2023-11-12 09:32:13 stop_mining: get power type version failed!
2023-11-12 09:32:13 uninit_temp_info
2023-11-12 09:32:13 do not read temp anymore...
2023-11-12 09:32:13 cancel thread
2023-11-12 09:32:13 cancel thread
2023-11-12 09:32:13 ****power off hashboard****
2023-11-12 09:32:13 temp monitor thread exit
2023-11-12 09:32:17 ERROR_SOC_INIT: soc init failed!
2023-11-12 09:32:17 stop_mining: soc init failed!
2023-11-12 09:32:17 ****power off hashboard****



and from our friends at Braiins.. with the newly shiny installed OS

2015-01-01T00:00:25.951420Z  INFO bosminer_plus_tuner::arch: Detected Hash Board #0:
+--------------------+-------------------------+
|Board name          |BHB42601                 |
|S/N                 |HBBIT000387007292        |
|BOM version         |0x1000                   |
|PCB version         |0x3001                   |
|Voltage   (Avg.)    |13.80 V                  |
|Frequency (Avg.)    |545 MHz                  |
|Hashrate            |35296.38 GH/s            |
+--------------------+-------------------------+
2015-01-01T00:00:25.951577Z  INFO bosminer_plus_tuner::arch: Detected Hash Board #1:
+--------------------+-------------------------+
|Board name          |BHB42601                 |
|S/N                 |HBBIT000335012713        |
|BOM version         |0x1000                   |
|PCB version         |0x3001                   |
|Voltage   (Avg.)    |13.80 V                  |
|Frequency (Avg.)    |545 MHz                  |
|Hashrate            |35296.38 GH/s            |
+--------------------+-------------------------+
2015-01-01T00:00:25.951633Z  INFO bosminer_plus_tuner::arch: Detected Hash Board #2:
+--------------------+-------------------------+
|Board name          |BHB42601                 |
|S/N                 |HBBIT000364003696        |
|BOM version         |0x1000                   |
|PCB version         |0x3001                   |
|Voltage   (Avg.)    |13.80 V                  |
|Frequency (Avg.)    |545 MHz                  |
|Hashrate            |35296.38 GH/s            |
+--------------------+-------------------------+
2015-01-01T00:00:25.956616Z  WARN bosminer_plus_tuner::tune::save: Failed to load autotuner registry: No such file or directory (os error 2), using empty autotuner registry
2015-01-01T00:00:25.963241Z  INFO bosminer::entry: Starting BOSminer (bosminer-plus-tuner 0.9.0-fd0c1e56) in paused state...
2015-01-01T00:00:25.963341Z  INFO bosminer::entry: Configured 65536 midstates
2015-01-01T00:00:25.964513Z  INFO bosminer_backend: Resolved monitor config: Config { fan_config: Some(FanControlConfig { mode: TargetTemperature(60.0), min_fans: 2, min_fan_rpm: 1800 }), temp_config: Some(TempControlConfig { dangerous_temp: 90.0, hot_temp: 80.0 }) }
2015-01-01T00:00:25.982099Z  INFO bosminer_backend::psu: PSU: Starting service task
2015-01-01T00:00:27.690037Z  INFO bosminer_am2_s17::hardware::antminer: PSU: version '0x71' detected
2023-11-12T00:42:51.600556Z  INFO bosminer_backend::psu: PSU monitor task starting
2023-11-12T00:42:51.600696Z  INFO bosminer_backend::miner: Initializing miner, detected_hashboards=[1, 2, 3]
2023-11-12T00:42:51.600924Z  WARN bosminer_backend::miner: Hashchain 2 disabled in config, skipping...
2023-11-12T00:42:51.600959Z  WARN bosminer_backend::miner: Hashchain 3 disabled in config, skipping...
2023-11-12T00:42:51.603790Z  INFO bosminer_plus_tuner::tune: Tune/all: Starting
2023-11-12T00:42:51.604985Z  INFO bosminer_plus_tuner::tune: Tune/all: Re-Starting miner
2023-11-12T00:42:51.605260Z  INFO bosminer_plus_tuner::tune::experiment: Tune/all: Status: starting chain
2023-11-12T00:42:51.605467Z  INFO bosminer_plus_tuner::tune::experiment: Waiting 100 s for miner to stabilize...
2023-11-12T00:42:52.071227Z  INFO bosminer::client::stratum_v2: log_message="Connected Stratum V2 (authority key: u95GEReVMjK6k5YqiSFNqqTnKU4ypU2Wm8awa6tmbmDmk1bWt) to: v2.stratum.braiins.com:3336"
2023-11-12T00:42:52.362049Z  INFO bosminer::backend: backend::Manager: Resuming triggered for the pause reason: dead pools
2023-11-12T00:42:53.610607Z  WARN bosminer::client::stratum_v2: log_message="dev-fee:stratum2+tcp://bdf_000.kRWMBcp9s8cA_wYA@a830bcc3.bos.braiins.com: Standard application shutdown"
2023-11-12T00:42:57.614893Z  INFO bosminer::backend: backend::Manager: Resuming triggered for the pause reason: missing license
2023-11-12T00:43:17.438076Z  INFO bosminer::client::stratum_v2: log_message="Stratum: changing target to 00000000003fffc0000000000000000000000000000000000000000000000000 diff=1024"
2023-11-12T00:43:47.678262Z  INFO bosminer::client::stratum_v2: log_message="Stratum: changing target to 00000000007fff80000000000000000000000000000000000000000000000000 diff=512"
2023-11-12T00:44:31.607441Z  INFO bosminer_plus_tuner::tune::experiment: Woken up
2023-11-12T00:44:31.610497Z  INFO bosminer_backend::psu: PSU: Enable
2023-11-12T00:44:32.619603Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-12T00:44:32.620996Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-12T00:44:34.051099Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-12T00:44:34.162409Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-12T00:44:35.215848Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-12T00:44:35.215916Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-12T00:44:35.215946Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-12T00:44:35.216000Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:35.216120Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-12T00:44:35.216136Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:35.216180Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-12T00:44:35.216304Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:36.334904Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-12T00:44:36.335025Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:44:36.536490Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-12T00:44:36.537307Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-12T00:44:36.538155Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-12T00:44:37.634204Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)
2023-11-12T00:44:47.635222Z  INFO bosminer_backend::miner: CHAIN/1: Retrying hashboard start...
2023-11-12T00:44:47.639752Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-12T00:44:47.639971Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-12T00:44:49.071513Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-12T00:44:49.182072Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-12T00:44:50.234545Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-12T00:44:50.234626Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-12T00:44:50.234724Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:50.234802Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-12T00:44:50.234858Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-12T00:44:50.235105Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-12T00:44:50.235192Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:50.235358Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:51.351441Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-12T00:44:51.351556Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:44:51.552931Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-12T00:44:51.553770Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-12T00:44:51.554457Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-12T00:44:52.649944Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)
2023-11-12T00:45:02.650990Z  INFO bosminer_backend::miner: CHAIN/1: Retrying hashboard start...
2023-11-12T00:45:02.655484Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-12T00:45:02.655722Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-12T00:45:04.084671Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-12T00:45:04.196199Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-12T00:45:05.249250Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-12T00:45:05.249387Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-12T00:45:05.249407Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-12T00:45:05.249427Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-12T00:45:05.249461Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:05.249621Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:05.249651Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-12T00:45:05.249855Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:06.367527Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-12T00:45:06.367641Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:45:06.568984Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-12T00:45:06.569669Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-12T00:45:06.570433Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-12T00:45:07.666458Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)
2023-11-12T00:45:17.667816Z  INFO bosminer_backend::miner: CHAIN/1: Retrying hashboard start...
2023-11-12T00:45:17.672369Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-12T00:45:17.672591Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-12T00:45:19.102579Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-12T00:45:19.213420Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-12T00:45:20.266461Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-12T00:45:20.266554Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-12T00:45:20.267552Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-12T00:45:20.267751Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-12T00:45:20.267846Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:20.268123Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-12T00:45:20.268194Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:20.268274Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:21.383480Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-12T00:45:21.383606Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:45:21.585002Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-12T00:45:21.585770Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-12T00:45:21.586562Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-12T00:45:22.682623Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)
2023-11-12T00 :45:22.682761Z  WARN bosminer_backend::miner: Chain start Error: InitError(1, Other(SHORT CIRCUIT - measured voltage 0.09 V))
2023-11-12T00:45:22.682933Z  INFO bosminer_plus_tuner::tune::experiment: Tune/all: Status: Hashchain refused to start: InitError(1, Other(SHORT CIRCUIT - measured voltage 0.09 V))
2023-11-12T00:45:22.682978Z  INFO bosminer_plus_tuner::tune::experiment: Tune/1: Disabling hashchain, reason: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:45:22.683174Z  INFO bosminer_plus_tuner::tune: Tune/all: Shutting down hashboards and restarting in: 10s
2023-11-12T00:45:32.684448Z  INFO bosminer_plus_tuner::tune: Tune/all: Re-Starting miner
2023-11-12T00:45:32.684540Z  INFO bosminer_plus_tuner::tune::experiment: Tune/all: Status: starting chain
2023-11-12T00:45:32.684749Z  INFO bosminer_backend::psu: PSU: Disable
2023-11-12T00:45:33.686432Z  INFO bosminer_plus_tuner::tune::experiment: Waiting 100 s for miner to stabilize...



Sorry.. I should have probably pastbin'd all this?

I've cleaned everything. I've unplugged and replugged everything in. I'm not an expert - but the PCIe connector is producing a nice clean 12v on the needed areas. Likewise my multi gives normal readings...

which makes me think of something in a Bitmain article about a "clerk" and "voltage" which I think was a bad translation for a voltage regulator in the Psupply?

Any connection guys?

All green. Just 0 hash.

[philipma1957]

Ok heres some funky for ya's

Tested boards - they seem ok ... as best as I can test them.

Installed braains on this AML s19pro so I have logs from both factory and braains.

Code:

Here's the factory:

2023-11-12 09:30:58 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :
2023-11-12 09:30:59 This is fix-freq version
2023-11-12 09:30:59 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2023-11-12 09:30:59 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2023-11-12 09:30:59 opt_multi_version     = 1
2023-11-12 09:30:59 opt_bitmain_ab        = 1
2023-11-12 09:30:59 mid_auto_gen          = 1
2023-11-12 09:30:59 opt_bitmain_work_mode = 0
2023-11-12 09:30:59 port 439 already exported
2023-11-12 09:30:59 port 454 already exported
2023-11-12 09:30:59 port 440 already exported
2023-11-12 09:30:59 port 455 already exported
2023-11-12 09:30:59 port 441 already exported
2023-11-12 09:30:59 port 456 already exported
2023-11-12 09:30:59 port 438 already exported
2023-11-12 09:30:59 port 453 already exported
2023-11-12 09:30:59 port 446 already exported
2023-11-12 09:30:59 port 445 already exported
2023-11-12 09:30:59 Note: front fan is power on!
2023-11-12 09:30:59 Note: rear fan is power on!
2023-11-12 09:30:59 start the http log.
2023-11-12 09:30:59 start listen on 6060 ...
2023-11-12 09:30:59 httpListenThread start ret=0
2023-11-12 09:30:59 bad chain id = 3
2023-11-12 09:31:02 bad chain id = 3
2023-11-12 09:31:04 ==========================capability start==========================
2023-11-12 09:31:04 board num = 3
2023-11-12 09:31:04 board id = 0, chain num = 1
2023-11-12 09:31:04 	chain id = 0
2023-11-12 09:31:04 board id = 1, chain num = 1
2023-11-12 09:31:04 	chain id = 1
2023-11-12 09:31:04 board id = 2, chain num = 1
2023-11-12 09:31:04 	chain id = 2
2023-11-12 09:31:04 ==========================capability end============================
2023-11-12 09:31:04 chain num = 3
2023-11-12 09:31:04 skip loading levels for now
2023-11-12 09:31:08 load chain 0 eeprom data
2023-11-12 09:31:12 load chain 1 eeprom data
2023-11-12 09:31:15 load chain 2 eeprom data
2023-11-12 09:31:15 i2c_sim_init start
2023-11-12 09:31:15 init gpio477
2023-11-12 09:31:15 init gpio476
2023-11-12 09:31:15 i2c_sim_init end
2023-11-12 09:31:16 power open power_version = 0x71
2023-11-12 09:31:22 power is not Calibrated
2023-11-12 09:31:23 miner type: Antminer S19j Pro
2023-11-12 09:31:23 multi machine mode
2023-11-12 09:31:23 load machine BHB42601 conf
2023-11-12 09:31:23 machine : BHB42601 
2023-11-12 09:31:23 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-11-12 09:31:23 abandon mix board!
2023-11-12 09:31:23 abandon mix board!
2023-11-12 09:31:23 fan_eft : 1  fan_pwm : 20
2023-11-12 09:31:23 create thread get_nonce_and_register_thread
2023-11-12 09:31:23 fixed working voltage = 1380
2023-11-12 09:31:23 fixed frequency is 545
2023-11-12 09:31:23 Chain [0] PCB Version: 0x0130
2023-11-12 09:31:23 Chain [0] BOM Version: 0x0010
2023-11-12 09:31:23 Chain [1] PCB Version: 0x0130
2023-11-12 09:31:23 Chain [1] BOM Version: 0x0010
2023-11-12 09:31:23 Chain [2] PCB Version: 0x0130
2023-11-12 09:31:23 Chain [2] BOM Version: 0x0010
2023-11-12 09:31:23 bad chain id = 3
2023-11-12 09:31:23 Fan check passed.
2023-11-12 09:31:23 uart_trans addr:0xf6fbb000.
2023-11-12 09:31:24 chain[0] PIC jump to app
2023-11-12 09:31:25 Check chain[0] PIC fw version=0x89
2023-11-12 09:31:26 chain[1] PIC jump to app
2023-11-12 09:31:28 Check chain[1] PIC fw version=0x89
2023-11-12 09:31:29 chain[2] PIC jump to app
2023-11-12 09:31:30 Check chain[2] PIC fw version=0x89
2023-11-12 09:31:31 create thread pic_heart_beat_thread
2023-11-12 09:31:31 max sensor num = 4
2023-11-12 09:31:31 STATUS_INITED: soc init done!
2023-11-12 09:31:31 temperature_monitor_thread start...
2023-11-12 09:31:34 start to init...
2023-11-12 09:31:34 warning:power is not calibration.
2023-11-12 09:31:35 power type version: 0x0071
2023-11-12 09:31:35 Initializing the power, please wait, this may take up to 2 minutes...
2023-11-12 09:32:06 Slept 30 seconds, diff = 0.
2023-11-12 09:32:07 set_voltage_by_steps to 1500.
2023-11-12 09:32:10 power voltage can not meet the target
2023-11-12 09:32:12 power voltage can not meet the target
2023-11-12 09:32:13 power voltage can not meet the target
2023-11-12 09:32:13 Sweep error string = V:1.
2023-11-12 09:32:13 ERROR_POWER_LOST: get power type version failed!
2023-11-12 09:32:13 stop_mining: get power type version failed!
2023-11-12 09:32:13 uninit_temp_info
2023-11-12 09:32:13 do not read temp anymore...
2023-11-12 09:32:13 cancel thread
2023-11-12 09:32:13 cancel thread
2023-11-12 09:32:13 ****power off hashboard****
2023-11-12 09:32:13 temp monitor thread exit
2023-11-12 09:32:17 ERROR_SOC_INIT: soc init failed!
2023-11-12 09:32:17 stop_mining: soc init failed!
2023-11-12 09:32:17 ****power off hashboard****

and from our friends at Braiins.. with the newly shiny installed OS

Code:

2015-01-01T00:00:25.951420Z  INFO bosminer_plus_tuner::arch: Detected Hash Board #0:
+--------------------+-------------------------+
|Board name          |BHB42601                 |
|S/N                 |HBBIT000387007292        |
|BOM version         |0x1000                   |
|PCB version         |0x3001                   |
|Voltage   (Avg.)    |13.80 V                  |
|Frequency (Avg.)    |545 MHz                  |
|Hashrate            |35296.38 GH/s            |
+--------------------+-------------------------+
2015-01-01T00:00:25.951577Z  INFO bosminer_plus_tuner::arch: Detected Hash Board #1:
+--------------------+-------------------------+
|Board name          |BHB42601                 |
|S/N                 |HBBIT000335012713        |
|BOM version         |0x1000                   |
|PCB version         |0x3001                   |
|Voltage   (Avg.)    |13.80 V                  |
|Frequency (Avg.)    |545 MHz                  |
|Hashrate            |35296.38 GH/s            |
+--------------------+-------------------------+
2015-01-01T00:00:25.951633Z  INFO bosminer_plus_tuner::arch: Detected Hash Board #2:
+--------------------+-------------------------+
|Board name          |BHB42601                 |
|S/N                 |HBBIT000364003696        |
|BOM version         |0x1000                   |
|PCB version         |0x3001                   |
|Voltage   (Avg.)    |13.80 V                  |
|Frequency (Avg.)    |545 MHz                  |
|Hashrate            |35296.38 GH/s            |
+--------------------+-------------------------+
2015-01-01T00:00:25.956616Z  WARN bosminer_plus_tuner::tune::save: Failed to load autotuner registry: No such file or directory (os error 2), using empty autotuner registry
2015-01-01T00:00:25.963241Z  INFO bosminer::entry: Starting BOSminer (bosminer-plus-tuner 0.9.0-fd0c1e56) in paused state...
2015-01-01T00:00:25.963341Z  INFO bosminer::entry: Configured 65536 midstates
2015-01-01T00:00:25.964513Z  INFO bosminer_backend: Resolved monitor config: Config { fan_config: Some(FanControlConfig { mode: TargetTemperature(60.0), min_fans: 2, min_fan_rpm: 1800 }), temp_config: Some(TempControlConfig { dangerous_temp: 90.0, hot_temp: 80.0 }) }
2015-01-01T00:00:25.982099Z  INFO bosminer_backend::psu: PSU: Starting service task
2015-01-01T00:00:27.690037Z  INFO bosminer_am2_s17::hardware::antminer: PSU: version '0x71' detected
2023-11-12T00:42:51.600556Z  INFO bosminer_backend::psu: PSU monitor task starting
2023-11-12T00:42:51.600696Z  INFO bosminer_backend::miner: Initializing miner, detected_hashboards=[1, 2, 3]
2023-11-12T00:42:51.600924Z  WARN bosminer_backend::miner: Hashchain 2 disabled in config, skipping...
2023-11-12T00:42:51.600959Z  WARN bosminer_backend::miner: Hashchain 3 disabled in config, skipping...
2023-11-12T00:42:51.603790Z  INFO bosminer_plus_tuner::tune: Tune/all: Starting
2023-11-12T00:42:51.604985Z  INFO bosminer_plus_tuner::tune: Tune/all: Re-Starting miner
2023-11-12T00:42:51.605260Z  INFO bosminer_plus_tuner::tune::experiment: Tune/all: Status: starting chain
2023-11-12T00:42:51.605467Z  INFO bosminer_plus_tuner::tune::experiment: Waiting 100 s for miner to stabilize...
2023-11-12T00:42:52.071227Z  INFO bosminer::client::stratum_v2: log_message="Connected Stratum V2 (authority key: u95GEReVMjK6k5YqiSFNqqTnKU4ypU2Wm8awa6tmbmDmk1bWt) to: v2.stratum.braiins.com:3336"
2023-11-12T00:42:52.362049Z  INFO bosminer::backend: backend::Manager: Resuming triggered for the pause reason: dead pools
2023-11-12T00:42:53.610607Z  WARN bosminer::client::stratum_v2: log_message="dev-fee:stratum2+tcp://bdf_000.kRWMBcp9s8cA_wYA@a830bcc3.bos.braiins.com: Standard application shutdown"
2023-11-12T00:42:57.614893Z  INFO bosminer::backend: backend::Manager: Resuming triggered for the pause reason: missing license
2023-11-12T00:43:17.438076Z  INFO bosminer::client::stratum_v2: log_message="Stratum: changing target to 00000000003fffc0000000000000000000000000000000000000000000000000 diff=1024"
2023-11-12T00:43:47.678262Z  INFO bosminer::client::stratum_v2: log_message="Stratum: changing target to 00000000007fff80000000000000000000000000000000000000000000000000 diff=512"
2023-11-12T00:44:31.607441Z  INFO bosminer_plus_tuner::tune::experiment: Woken up
2023-11-12T00:44:31.610497Z  INFO bosminer_backend::psu: PSU: Enable
2023-11-12T00:44:32.619603Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-12T00:44:32.620996Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-12T00:44:34.051099Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-12T00:44:34.162409Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-12T00:44:35.215848Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-12T00:44:35.215916Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-12T00:44:35.215946Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-12T00:44:35.216000Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:35.216120Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-12T00:44:35.216136Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:35.216180Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-12T00:44:35.216304Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:36.334904Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-12T00:44:36.335025Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:44:36.536490Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-12T00:44:36.537307Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-12T00:44:36.538155Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-12T00:44:37.634204Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)
2023-11-12T00:44:47.635222Z  INFO bosminer_backend::miner: CHAIN/1: Retrying hashboard start...
2023-11-12T00:44:47.639752Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-12T00:44:47.639971Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-12T00:44:49.071513Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-12T00:44:49.182072Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-12T00:44:50.234545Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-12T00:44:50.234626Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-12T00:44:50.234724Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:50.234802Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-12T00:44:50.234858Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-12T00:44:50.235105Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-12T00:44:50.235192Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:50.235358Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:44:51.351441Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-12T00:44:51.351556Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:44:51.552931Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-12T00:44:51.553770Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-12T00:44:51.554457Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-12T00:44:52.649944Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)
2023-11-12T00:45:02.650990Z  INFO bosminer_backend::miner: CHAIN/1: Retrying hashboard start...
2023-11-12T00:45:02.655484Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-12T00:45:02.655722Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-12T00:45:04.084671Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-12T00:45:04.196199Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-12T00:45:05.249250Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-12T00:45:05.249387Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-12T00:45:05.249407Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-12T00:45:05.249427Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-12T00:45:05.249461Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:05.249621Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:05.249651Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-12T00:45:05.249855Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:06.367527Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-12T00:45:06.367641Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:45:06.568984Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-12T00:45:06.569669Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-12T00:45:06.570433Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-12T00:45:07.666458Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)
2023-11-12T00:45:17.667816Z  INFO bosminer_backend::miner: CHAIN/1: Retrying hashboard start...
2023-11-12T00:45:17.672369Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-12T00:45:17.672591Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-12T00:45:19.102579Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-12T00:45:19.213420Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-12T00:45:20.266461Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-12T00:45:20.266554Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-12T00:45:20.267552Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-12T00:45:20.267751Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-12T00:45:20.267846Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:20.268123Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-12T00:45:20.268194Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:20.268274Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-12T00:45:21.383480Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-12T00:45:21.383606Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:45:21.585002Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-12T00:45:21.585770Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-12T00:45:21.586562Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-12T00:45:22.682623Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)
2023-11-12T00 :45:22.682761Z  WARN bosminer_backend::miner: Chain start Error: InitError(1, Other(SHORT CIRCUIT - measured voltage 0.09 V))
2023-11-12T00:45:22.682933Z  INFO bosminer_plus_tuner::tune::experiment: Tune/all: Status: Hashchain refused to start: InitError(1, Other(SHORT CIRCUIT - measured voltage 0.09 V))
2023-11-12T00:45:22.682978Z  INFO bosminer_plus_tuner::tune::experiment: Tune/1: Disabling hashchain, reason: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-12T00:45:22.683174Z  INFO bosminer_plus_tuner::tune: Tune/all: Shutting down hashboards and restarting in: 10s
2023-11-12T00:45:32.684448Z  INFO bosminer_plus_tuner::tune: Tune/all: Re-Starting miner
2023-11-12T00:45:32.684540Z  INFO bosminer_plus_tuner::tune::experiment: Tune/all: Status: starting chain
2023-11-12T00:45:32.684749Z  INFO bosminer_backend::psu: PSU: Disable
2023-11-12T00:45:33.686432Z  INFO bosminer_plus_tuner::tune::experiment: Waiting 100 s for miner to stabilize...

Sorry.. I should have probably pastbin'd all this?

I've cleaned everything. I've unplugged and replugged everything in. I'm not an expert - but the PCIe connector is producing a nice clean 12v on the needed areas. Likewise my multi gives normal readings...

which makes me think of something in a Bitmain article about a "clerk" and "voltage" which I think was a bad translation for a voltage regulator in the Psupply?

Any connection guys?

All green. Just 0 hash.

okay we use   [  code   ]   [ /code ] to shorten it.

looks like bad psu in the first one

looks like bad hashboard in the second one.


so lets go to brains setup with the 1 board that reads short.

I assume you only had 1 board in the gear

the other 2 boards you had outside the gear.

try the one board but move the white communication wire to a different controller slot.

99 percent sure you get same error

then try moving the white wire to the third slot in the controller 99 percent sure same error.

At this point pull the board place it to the side label it  ?shorted?

test a second board same way.

if all boards fail it is a bit more likely the psu is bad

if 1 or 2  boards work it was a short in the boards

do you have 5 machines.

You can really do a lot of board testing if just one or two of the first three work is means the psu is good and you

can test all 15 boards.

If first 3 boards fail test only 3 more if you are 0 for six.

switch to next psu.

see if a board works from the six you tested. just do 1 of this six on the second psu.

if it works your first psu was bad.
if it does not work go to a new 7th board form the 3rd machine. if it fails test the other 2 on that 3rd machine

at this point you will have tested 9 boards and 2 psi's.  If they are all bad it is likely you had a major event fry controllers.

If you are  New York you could contact my repair guy


https://vmssecuritycloud.com/

his name is Greg tell him Phil from New Jersey recommended him to you.

good luck.


note I thought you were the guy with 5 bad s17s.

if you only have the 1 s19j just do the three boards 1 at a time and also try switching the white communication cable.

[ph0d]

many thanks for the tip(s). I did most of the tests you recommended and indeed all points towards PSU. Hashboard may have been unplugged or half connected when I was doing my ghetto diag posts. But when everything is plugged in... everything is groovy except for the short circuit message. Following  your advice with what I have and reseating everything/changing white cables around/making things look pretty etc


<code>      8.949980] Antminer S19J Pro
[    8.950174] \x1b[2m2015-01-01T00:00:17.802672Z\x1b[0m \x1b[32m INFO\x1b[0m \x1b[2mbosminer_plus_tuner::arch\x1b[0m\x1b[2m:\x1b[0m Detected Hash Board #0:
               +--------------------+-------------------------+
               |Board name          |BHB42601                 |
               |S/N                 |HBBIT000387007292        |
               |BOM version         |0x1000                   |
               |PCB version         |0x3001                   |
               |Voltage   (Avg.)    |13.80 V                  |
               |Frequency (Avg.)    |545 MHz                  |
               |Hashrate            |35296.38 GH/s            |
               +--------------------+-------------------------+
</code>

from end of dmesg

<code>
2015-01-01T00:00:23.720582Z  INFO bosminer_backend::miner: Initializing miner, detected_hashboards=[1]
2015-01-01T00:00:23.724608Z  INFO bosminer_plus_tuner::tune: Tune/all: Starting
2015-01-01T00:00:23.725579Z  INFO bosminer_plus_tuner::tune: Tune/all: Entering STAGE 6: Tuner disabled
2015-01-01T00:00:23.725965Z  INFO bosminer_plus_tuner::tune::experiment: Tune/all: Status: starting chain
2015-01-01T00:00:23.727699Z  INFO bosminer_plus_tuner::tune::experiment: Waiting 100 s for miner to stabilize...
2015-01-01T00:00:23.728893Z  INFO bosminer::backend: backend::Manager: Resuming triggered for the pause reason: missing license
2015-01-01T00:00:23.976478Z  INFO bosminer::client::stratum_v2: log_message="Connected Stratum V2 (authority key: u95GEReVMjK6k5YqiSFNqqTnKU4ypU2Wm8awa6tmbmDmk1bWt) to: v2.us-east.stratum.braiins.com:3336"
2015-01-01T00:00:24.110729Z  INFO bosminer::backend: backend::Manager: Resuming triggered for the pause reason: dead pools
2015-01-01T00:00:25.730215Z  WARN bosminer::client::stratum_v2: log_message="dev-fee:stratum2+tcp://bdf_000.kRWMBcp9s8cA_wYA@a830bcc3.bos.braiins.com: Standard application shutdown"
2023-11-14T20:25:52.956224Z  INFO bosminer::client::stratum_v2: log_message="Stratum: changing target to 00000000003fffc0000000000000000000000000000000000000000000000000 diff=1024"
2023-11-14T20:26:22.682984Z  INFO bosminer::client::stratum_v2: log_message="Stratum: changing target to 00000000007fff80000000000000000000000000000000000000000000000000 diff=512"
2023-11-14T20:26:46.264926Z  INFO bosminer_plus_tuner::tune::experiment: Woken up
2023-11-14T20:26:46.271089Z  INFO bosminer_backend::psu: PSU: Enable
2023-11-14T20:26:47.277058Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-14T20:26:47.277323Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-14T20:26:48.711135Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-14T20:26:48.823082Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-14T20:26:49.875659Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-14T20:26:49.875726Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-14T20:26:49.875778Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-14T20:26:49.876013Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-14T20:26:49.876186Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-14T20:26:49.876495Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-14T20:26:49.879306Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-14T20:26:49.879509Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-14T20:26:50.995410Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-14T20:26:50.995535Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-14T20:26:51.197067Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-14T20:26:51.199840Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-14T20:26:51.200569Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-14T20:26:52.298337Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)
2023-11-14T20:27:02.300755Z  INFO bosminer_backend::miner: CHAIN/1: Retrying hashboard start...
2023-11-14T20:27:02.311133Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-14T20:27:02.311415Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-14T20:27:03.745537Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-14T20:27:03.859560Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-14T20:27:04.912929Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-14T20:27:04.912958Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-14T20:27:04.913025Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-14T20:27:04.912811Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-14T20:27:04.913321Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-14T20:27:04.913515Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-14T20:27:04.913705Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-14T20:27:04.913889Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-14T20:27:06.031624Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.07 V, expected 15.20 V)
2023-11-14T20:27:06.031738Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.07 V
2023-11-14T20:27:06.234188Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-14T20:27:06.235462Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-14T20:27:06.236155Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-14T20:27:07.333284Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.07 V)
2023-11-14T20:27:17.336936Z  INFO bosminer_backend::miner: CHAIN/1: Retrying hashboard start...
2023-11-14T20:27:17.347374Z  INFO bosminer_backend::worker: SerialWorker: detected 4 CPU cores available, using 4
2023-11-14T20:27:17.347554Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller reset
2023-11-14T20:27:18.779273Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller application started
2023-11-14T20:27:18.891923Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Voltage controller firmware version 0x89
2023-11-14T20:27:19.945625Z  INFO bosminer_backend::hashchain: CHAIN/1: Initializing (fingerprint: 553226cdc534aee1)
2023-11-14T20:27:19.951811Z  INFO bosminer_backend::worker: WorkGen/1: Starting on cpu #1
2023-11-14T20:27:19.951993Z  INFO bosminer_backend::hashchain: CHAIN/1: Resetting hash board
2023-11-14T20:27:19.952454Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-14T20:27:19.953548Z  INFO bosminer_backend::worker: Serial/W/1: Starting on cpu #1
2023-11-14T20:27:19.953545Z  INFO bosminer_backend::worker: Serial/R/1: Starting on cpu #1
2023-11-14T20:27:19.953712Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-14T20:27:19.953900Z  INFO bosminer_hal::thread_utils: Running on core: 1
2023-11-14T20:27:21.070702Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Waiting for voltage to settle (measured 0.09 V, expected 15.20 V)
2023-11-14T20:27:21.072037Z ERROR bosminer_backend::hashchain: CHAIN/1: Init failed: SHORT CIRCUIT - measured voltage 0.09 V
2023-11-14T20:27:21.273441Z  INFO bosminer_backend::worker: CHAIN/1: Halting worker threads...
2023-11-14T20:27:21.276675Z  WARN bosminer_backend::worker: WorkGen/1: Exiting because "SendError(..)"
2023-11-14T20:27:21.277490Z  INFO bosminer_am2_s17::hardware::hashboard::power::antminer: PWR/1: Disable voltage
2023-11-14T20:27:22.374920Z ERROR bosminer_backend::miner: CHAIN/1: Start failed: Other(SHORT CIRCUIT - measured voltage 0.09 V)

</code>

One interesting thing - each of the hash slots returns a unique but constant voltage on the short circuit. Sounds like something is toasty in the PSU? In this case slot 1 is .09, slot 2 comes up as .2x. This is my only S19Pro so I'm limited in terms of further testing. But I'm fairly sure i've ruled out everything - except for the PSU. I made the possibly unwise choice of buying an S17 to "play with" some. I'll experiment on it to see what kind of things braiins says when I fiddle with it.

Will definitely reach out to your guy. THanks a bunch for your time! Happy mining!