Antminer Control s17Pro not work not ip not flashing green and red led on

[Point2003]

Hello

I'm new here

i have a question


My miner control s17Pro ctrl c49 have this problem

not flashing
not ip
sd card not work whit recovery

red and green led its on of the control

whats is the problem from the control Board

sorry my english ist not perfekt

hope you guys can help me

[1715120289]

1715120289

[1715120289]

1715120289

[1715120289]

1715120289

[BitMaxz]

Did you flash it with the wrong firmware?
Did you recently upgrade it to the latest version?

Anyway, would you mind to try flashing it or boot it with Braiins OS and Let see if the control board is still fine or not follow the guide below

- https://docs.braiins.com/os/20.03/open-source-en/Setup/1_install.html

[Point2003]

Did you flash it with the wrong firmware? yes braiins os+
Did you recently upgrade it to the latest version? No

Anyway, would you mind to try flashing it or boot it with Braiins OS and Let see if the control board is still fine or not follow the guide below

- https://docs.braiins.com/os/20.03/open-source-en/Setup/1_install.html

Have tried the upper Methods whit starting from sd not work

[Point2003]

I can't find an IP on the network either

on the board also not light up all 3 green leds

reset not work ip report not work

What can it be?

[BitMaxz]

I can't find an IP on the network either

on the board also not light up all 3 green leds

reset not work ip report not work

What can it be?

Try to disconnect all hashboard from the control board and flash or boot it again with the SD card recovery.
If it doesn't work try to replace the SD card sometimes some fake SD card when pasting the firmware to the SD Card it becomes corrupted so make sure that you are using an authentic SD card then try to flash it again.

[Point2003]

SD card is new and working 8GB WD

PCB is removed and host powered 12V 10A

It doesn't matter if it's Braiin's OS or original company goods, everything doesn't work

I can send him pictures then you can see what the board is doing

[BitMaxz]

SD card is new and working 8GB WD

PCB is removed and host powered 12V 10A

It doesn't matter if it's Braiin's OS or original company goods, everything doesn't work

I can send him pictures then you can see what the board is doing

If it doesn't work try to flash it through the serial port(RX, TX, gnd).

- https://www.zeusbtc.com/articles/asic-miner-troubleshooting/1082-recovery-method-of-miner-serial-port-virus

If still does not work then its possible the control board has a hardware issue you don't have other choice but to replace the control board or hire a professional tech for repair.

[Point2003]

oki thanks I'll try it

oki usb ttl i can connect it


What program do I have to take Windows 11??

[JessieJames13]

oki thanks I'll try it

oki usb ttl i can connect it


What program do I have to take Windows 11??

You can use putty on windows.
Then modify the cmd to meet your situation

Code:

 /dev/ttyS0 115200

Post your SERIAL output data here.

[Point2003]

thanks

But it doesn't work


cmd with admin open but doesn't work

com3 its aktiv bit 9600


But the command doesn't work

[BitMaxz]

thanks

But it doesn't work


cmd with admin open but doesn't work

com3 its aktiv bit 9600


But the command doesn't work

Did you power the unit? Check the wire and terminals carefully RX, TX, and GND.

Keep repeating the procedure or better use other serial port software.
Also, get some ideas from these links below

- https://bitcointalk.org/index.php?topic=2386296.0
- https://bitcointalk.org/index.php?topic=5201015.0
- https://wiki.sipeed.com/soft/maixpy/en/get_started/env_serial_tools.html