Dragon ore mining machine (five modules T- class) overclocking IMG installation configuration instructions
1.There are some questions need to make sure before overclocking:
(1) Whether your T-class miner can overclocking?
This IMG is for the first few batch of dragon ore mining machine five- module, only five-module machine have a promotion effect.The method of making sure five-module is simple, from the case to inside the mill, if you have five pieces of circuit boards, each circuit board have the green light, it is five-module; Also can be in the mill console applications, click on the "real-time monitoring of mining machine" button, open the mime interface, view how many the modules are. As shown in figure 1, 0 1 2 3 4 ASC for five-module mill. If only 0 1 2 3 ,it is 4-module machine, the following article dont need to waste time to read.
http://img02.taobaocdn.com/imgextra/i2/914324192/T2uTl8XG4aXXXXXXXX_!!914324192.jpg(2) How many your miner overclocking to?
According to different module constitution, the overclocking figure in 1.08 T ~ 1.25 T (this data is the newest data after we ourselves overclocking 213 miners,less than 10 miners cant overclocking 1.1 T, most in 1.125 T;another batch of 98 sets of good constitution, directly on the 1.2 T, because of there is no power supply,it not top to 1.25 T).Although the same ore machine,there is bigger difference between each module constitution , so set respectively the frequency of each module in the overclocking package,to adapt to the different physical modules.
(3) How to determine your miner constitution?
Overclocking a period of time, in real-time monitoring interface, check the error rate of each module,that is to say DH or HW,if less than 6%, the constitution is good;if is 0% that is very good;if more than 10%,it is better to not overclocking.We adjust each module frequency according to the DH values, so that digging the potential of mining machine maximum. Normally we control within 8% of the DH.
(4) Do you charge the IMG?
IMG no charge, but need to register when using, registration requires a small fee. In the spirit of sharing,the IMG without registration provided in the appropriate time after a month. If you have sufficient funds,you can spend to register;if you don't want to spend money,you can use wait for period of time.
(5) What extension functions of the new IMG ?
In addition to the official automatic mining and difficulty setting function, we are making remote monitoring function module,it is free upgrade after completing.
(6) Whether manufacturers guarantee the wattanty after upgrade?
Because of no seal on the five-module miner,we guarantee the warranty after openning the box. But IMG update background interface changes, the official is not warranty.So it's better to purchased a high-speed 8G SD card (30M speed) to make a new system, the original SD card to save good, once mining machine is broken, install the old SD card back and returned to the factory warranty.
Upgrade IMG instructions:
(1) Download overclocking IMG and writing SD software tools.
Overclocking IMG download address: login Ark mining station network location (
http://pan.baidu.com/s/1ntpxbBj), into the "dragon SD_IMG ore mining machine" folder can see overclocking IMG, as shown in figure 2.
http://img03.taobaocdn.com/imgextra/i3/914324192/T2Qo48XJ0aXXXXXXXX_!!914324192.jpgThere are two files in Network location:one is the writing tool package Win32DiskImager,the other is "fz49 overclocking. Rar" dragon SD card of ore mining machine overclocking IMG compressed package. To download the two files to a free space of more than 8G plate,decompression respectively.
(2) Burning SD card
Insert the SD card to card reader, insert the card reader to the computer (if it is right, then the computer should add a mobile disk, my machine is J, open Win32DiskImager.exe, as shown in figure 3.
http://img04.taobaocdn.com/imgextra/i4/914324192/T29uV8XLRaXXXXXXXX_!!914324192.jpg① select the disk whith the card reader in (if card reader connected properly, then open the program, the program will automatically selected, without change)
② select the image to write to file
③ press the button "write" to write, when prompted to rewrite the entire content of the SD card, press OK.
Writing process need a period of time, depending on the image file size and speed of reading card.
(3) Install the SD card
Open the chassis (take the case on the surface of the top eight screws), remove the old SD card on raspberries, safekeeping, in case of warranty. Put on the new SD card. As shown in figure 4.
http://img03.taobaocdn.com/imgextra/i3/914324192/T229N8XFtaXXXXXXXX_!!914324192.jpg(4) Equipped with power supply
For the question of whether or not to need to add power supply, the experiment has proved that each module overclocking 900 frequency,no need to add power supply.If mining machine constitution is good ,after overclocking 900, DH still not high, friends of mine ready to hit the 1.25T , must add power supply. This site is to use the server blade power conversion, output for two 6 pin heads, mill power supply line is divided into two kinds, one kind is with tieline, this direct turn 6 pin electrical source on interfaces. As shown in figure 5.
http://img04.taobaocdn.com/imgextra/i4/914324192/T2ZImaXOlXXXXXXXXX_!!914324192.jpgAnother kind of power supply interface is the power cord directly on the 8 pin mouth of module,the 6 pin head can't directly to the module,power supply is negative,cut the line of 6 pin head,exchange the yellow and black line. After that,pick up 6 pin head on the module 8 pin,empty two mouth.
The original power supply with four modules, extra plus power with one module, 3 + 2 is also possible, of course. Attention to boot, first open with extra power supply,then open the main power supply;when power off,first close the main power supply,then close extra plus power supply.
3.Registration and setup instructions:
The default IP for new SD card is 192.168.1.10, use this IP login to mill the console interface, software registration screen appears as shown in figure 6.
http://img03.taobaocdn.com/imgextra/i3/914324192/T2RXybXGxXXXXXXXXX_!!914324192.jpgIf the registered ID is 88888888, the system has not yet been read mill information, please open the console or refresh a few times. Until out of something similar to figure 6 registration ID, click on the "click here to get registration code" link, enter the registration screen, as shown in figure 7.
http://img04.taobaocdn.com/imgextra/i4/914324192/T2im4_XHVaXXXXXXXX_!!914324192.jpgAccording to the customer service provided by the login account and password to register background interface. Click on the "software registration" - > "add registered",copy the registered ID on the mine. As shown in figure 8.
http://img01.taobaocdn.com/imgextra/i1/914324192/T2p41aXJtXXXXXXXXX_!!914324192.jpgFinished, click "submit" button.
You can see the registration in the registered list. The registration code is copied into the mill background registration code box. Finished, click "submit registration code", can be set into the interface. As shown in figure 9.
http://img03.taobaocdn.com/imgextra/i3/914324192/T2WPV.XU4XXXXXXXXX_!!914324192.jpgThen according to official instruction to set mill,everyone knows,we will not say more here.
4.The renderings after overclocking
Three prototype, BTC1 blue line not overclocking, BTC2 super to the black line 850, BTC3 super to the green line 900. All without power supply. Specific overclocking evaluation, this website to open another post for detailed explanation.
http://img01.taobaocdn.com/imgextra/i1/914324192/T2R7eaXJNXXXXXXXXX_!!914324192.jpgMining pool effect of mine not overclocking:
http://img02.taobaocdn.com/imgextra/i2/914324192/T2R8d8XLRaXXXXXXXX_!!914324192.pngMining pool effect of mine overclocking:
http://img03.taobaocdn.com/imgextra/i3/914324192/T2.0t.XGdaXXXXXXXX_!!914324192.pngMiner factory, a lot of machines for sale, want to buy contact us
http://img02.taobaocdn.com/imgextra/i2/914324192/T2YA9aXJ4XXXXXXXXX_!!914324192.jpghttp://img03.taobaocdn.com/imgextra/i3/914324192/T2woaaXHlXXXXXXXXX_!!914324192.jpghttp://img03.taobaocdn.com/imgextra/i3/914324192/T2zph9XIRaXXXXXXXX_!!914324192.jpgNotice: need english steps pictures, pls contact us!
Accept Miner Reservation
Email and Skype:chengying0115@hotmail.com
