[P2Pool AU Node]Norgz Pool BTC 0% fee Matt's Relay

[lovenlifelarge]

Norgz - Diff settings for a C1 - 1th Bitmain unit for ur p2pool?
What should they b to max it out?

[1714186634]

1714186634

[norgan]

Norgz - Diff settings for a C1 - 1th Bitmain unit for ur p2pool?
What should they b to max it out?

Optimising Shares:

If your running S1's set <share> to 0 ("0" defaults to lowest p2pool diff, currently 1677854.73)

And <pseudo_share> to 220.4 (optimized for 190GH/s)

<pseudo_share> is calculated as your hash rate in KH/s times 0.00000116

i.e. 190,000,000 * 0.00000116 = 220.4

Here is an example for an ant S1:

Code:

19vXrwKGUhK4cCU8tA4kWZgbChcmh9a6qj/0+220.4

If you have a hash rate over 1TH/s you might consider upping your share diff to something higher then the p2pool minimum to reduce network traffic and increase the value of your shares


For a C1 1000000000 * 0.00000116 = 1160

So something like btcaddress/0+1160

Or perhaps btcaddress/1+1160? You'll need to experiment. Considering the node only has two miners and they are a similar hash rate i doubt it will make a huge difference in the end.

[norgan]

There is some info about it here https://bitcointalk.org/index.php?topic=18313.11220

You could also ask in that thread about other c1's on p2pool. I don't set mine, I just let p2pool take care of it.

[lovenlifelarge]

Hey i havent been paid out on the last three blocks?? Can u tell me whats going on???

[norgan]

Hey i havent been paid out on the last three blocks?? Can u tell me whats going on???

Check the graphs, you mustn't have had valid shares in the chain to pay on those blocks. Two things need to happen for a payout:
1. You need to hash shares and have them successfully submit to the sharechain
2. You need those shares to stay valid until the next block, shares can fall off before the block is solved.

I gain and loose shares all the time, that can be seen on the graphs that my payout goes up and down depending on the shares I have on the sharechain.

[lovenlifelarge]

Its something to do with the address i was using is there anyway to recover those coins??

I changed my address & i haven't had a problem since

[norgan]

Its something to do with the address i was using is there anyway to recover those coins??

I changed my address & i haven't had a problem since

Good to hear you got it fixed. Since your shares are submitted under that Bitcoin address they belong to that address. I do not know of a way to recover those shares unfortunately.

[lovenlifelarge]

I do own the address but its a vicurex address...

Any thoughts other than asking them??

I've just order a S4 as well...

[norgan]

I do own the address but its a vicurex address...

Any thoughts other than asking them??

I've just order a S4 as well...

You can only go to the blockchain listing and ask them to return the btc shown coming from p2pool (freshly minted btc).

[lovenlifelarge]

Ok now u've got me, How do i go about that? Cause i have no idea... & in light of that where or who will the coins be returned to??

[norgan]

Ok now u've got me, How do i go about that? Cause i have no idea... & in light of that where or who will the coins be returned to??

Like this: blockchain.info/address/1MinerGcfwXJW6BETKLPQTmKYomc1uGAXy

But put the address you were using at the end instead of mine. So you had an address with these guys for trading? Did they state that you can't mine directly to it? They usually do with exchanges.

Long story short your btc is lost and it's unlikely you'll get it back, one disadvantage of unregulated currency although you'd be no better off if you had done an eft transfer of fiat currency.

 

[lovenlifelarge]

It does state & i've only just realised that meant p2pool too...

No Prob's thanks for your help..

[lovenlifelarge]

Norgz, Can u tell me, What type of miners are u using & whats ur total speed??

If u want u can PM me this information!

[norgan]

Norgz, Can u tell me, What type of miners are u using & whats ur total speed??

If u want u can PM me this information!

I have two S3's and an S1. They clock in all up at around 1.1th/s. You can see it on the graphs page under the 1miner address.

[lovenlifelarge]

Wanna buy some s3's? $100.00 each, I have 3 & s1's $50 each, I have 2.

Do u live in Sydney?? I can drop off...

I'm running 3 x s3's at the moment & a 1 x c1.

I'm running the C1 on your pool...

But i have a S4 coming...

[lovenlifelarge]

If anyone else wants them, Please PM me... Same price plus postage..

[norgan]

Found an issue on the node with the relay client. Node back online now. Will restart the relay client once Matt gives the ok.

[lovenlifelarge]

Norgz,

When u mine with your miners are u mining with all 3 miners on the one address & if so do u find u get a lot of duplicate shares or rejects??

Maybe more that u would if u mined on a different address for each miner or would u have less chance of finding shares & get paid less if u mined under 3 addresses??

[norgan]

Norgz,

When u mine with your miners are u mining with all 3 miners on the one address & if so do u find u get a lot of duplicate shares or rejects??

Maybe more that u would if u mined on a different address for each miner or would u have less chance of finding shares & get paid less if u mined under 3 addresses??

I always mine all three with the one address and don't have any issues. they all send and receive shares perfectly fine.

[smoothfreeze]

Hi guys, new to the whole bitcoin scene and stumbled upon this pool.

Currently mining using GUIMiner on my laptop and mining at 32ish MHash/s (this is slow, right?). I have a couple of questions:

What are shares? Mine is currently showing 10 shares accepted

How and when do I get my bitcoins?

How do I keep track of the transactions?

Will mining on my laptop fry it?

If anyone could give me an answer, that would be great. Sorry, total noooob here.