|
Acejam (OP)
|
 |
September 08, 2014, 05:38:07 PM
Last edit: July 10, 2019, 07:10:18 PM by Acejam |
|
...
|
|
|
|
|
|
|
|
|
|
|
|
"With e-currency based on cryptographic proof, without the need to
trust a third party middleman, money can be secure and transactions
effortless." -- Satoshi
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
dogie
Legendary
 Offline
Activity: 1666
Merit: 1183
dogiecoin.com
|
|
September 08, 2014, 05:43:24 PM |
|
Those 3 pins are all 12V, its not a short, its just too much load. Up to you if you choose to continue to use the PSU, no one can choose your risk level for you.
|
|
|
|
DrG
Legendary
Offline
Activity: 2086
Merit: 1035
|
|
September 08, 2014, 07:40:53 PM |
|
Why don´t you just open it and rewire a new 6-pin connector?
Opening it voids the warranty. EVGA is good with RMAs but they don't want users trying to service things. |
|
|
|
|
|
wh00per
|
|
September 08, 2014, 07:47:31 PM |
|
I guess the compressed air was the culprit .. since it's cold when it expands and I dunno what humidity levels were there.
The things get hot when they have a resistance load to dissipate the heat, in this case, the cable was the weaker link.
If you spray then up, give them some time before you plug them back in. I usually vacuum them and dust them up using a paintbrush.
Also, make sure you're grounded (just in case) to avoid damaging parts by static electricity.
You can use the other ones onward, no worries. But take more care when you clean them up.
|
CSA/cUL Certified Power Distribution Panels - Basic, Switched, Metered. 1-3 phases. Up to 600V. NMC:N4F9qvHz11BHcc4nh1LCJFsrZhA1EWgVwj
|
|
|
Soros Shorts
Donator
Legendary
Offline
Activity: 1617
Merit: 1011
|
|
September 09, 2014, 01:10:29 AM |
|
Maybe that particular S1 board has developed a fault and is now drawing more than the expected 207.5W?
When you turn the miners back on, you should check to see that they are still drawing 830W and not something significantly higher.
|
|
|
|
|
Blazed
Casascius Addict
Legendary
Offline
Activity: 2128
Merit: 1119
|
|
September 09, 2014, 01:15:06 AM |
|
I had a PSU do the same thing and it still ran fine. We're you using only 1 cable to power the ant? As in 1 cable that has 2 x PCI-e connectors on the end? You should be using 4 PCI-e cables off the PSU to power 2 ants.
|
|
|
|
|
|
jddebug
|
|
September 09, 2014, 02:21:38 AM |
|
My guess is when you plugged them back in you didn't get it on tight and that caused a poor connection and it heated up and burned. Should be fine when you replace the cable.
|
|
|
|
|
cloverme
Legendary
Offline
Activity: 1512
Merit: 1054
SpacePirate.io
|
|
September 09, 2014, 04:07:15 AM |
|
Just do the RMA on the warranty... I've had great success sending in dead power supplies to evga for a replacement. http://www.evga.com/support/warranty/ |
|
|
|
|
DrG
Legendary
Offline
Activity: 2086
Merit: 1035
|
|
September 09, 2014, 04:14:27 AM |
|
+1. EVGA had a 2 day turnaround on a cheap 600W Bronze I sent them. It helps I live 10 miles from them but the RMA was very easy - no hoops to jump through. I had a Seasonic 750 melt a cable like that when connected to my BFL Single. I still don't know if it was the Seasonic unit, the cable or the BFL ASIC. |
|
|
|
|
|
ravin
|
|
September 09, 2014, 04:34:38 AM |
|
I would definitely RMA it if I don't have to keep any antminers switched off because I dont have any PSU left. If I have other PSUs, I will see if the problem is with Antminer itself. Also, I don't think anyone's gonna suggest you try to use this faulty PSU anymore even if you have plenty of cables and pcies left. |
|
|
|
|
|
