rafoute59 (OP)
Newbie
 Offline
Activity: 10
Merit: 0
|
 |
January 03, 2015, 05:59:45 PM
Last edit: January 04, 2015, 12:27:03 PM by rafoute59 |
|
Accidently, i deleted my lan interface in the miner configuration, i tried to reset it but it don't work.
Anyone can help me ?
|
|
|
|
|
|
|
|
|
|
|
|
|
|
"Your bitcoin is secured in a way that is physically impossible for others to access, no matter for what reason, no matter how good the excuse, no matter a majority of miners, no matter what." -- Greg Maxwell
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
needFREElunch
Full Member
Offline
Activity: 196
Merit: 100
Hi
|
 |
January 03, 2015, 06:38:27 PM |
|
Accidently, i deleted my lan interface in the miner configuration, i tried to reset it but it don't work.
Anyone can help me ?
You will probably need to reset it back to factory settings (and then make any adjustments that you previously made again). |
|
|
|
rafoute59 (OP)
Newbie
Offline
Activity: 10
Merit: 0
|
|
January 03, 2015, 10:01:04 PM |
|
How to?
|
|
|
|
|
MyRig
Donator
Hero Member
Offline
Activity: 792
Merit: 510
support@myrig.com
|
|
January 03, 2015, 10:15:44 PM |
|
Please power on the S3 and let it run for at least 3 minutes! Then please find a little hole next to the network port (right hand side) Use a paperclip or cellphone Sim card ejector Pin (or similer) to push a little knob inside that hole in the below picture and hold it for at least 5 - 10 seconds. Let it go, and wait for 3 minutes, and power it off. Please wait for another 30 seconds, then power it back on and it should be reset to 192.168.1.99 IP and all should be the factory reset condition  How to?
|
Antminer & DragonMint Repair E-mail: support@myrig.com T: @MyRig_com Return Address: MyRig 3700 Quebec Street, Unit 100-239, Denver, Colorado 80207, USA |
|
|
rafoute59 (OP)
Newbie
Offline
Activity: 10
Merit: 0
|
|
January 04, 2015, 12:14:07 PM |
|
Not working.
Any "hardware" solution via USB ? Or something like that
|
|
|
|
|
rafoute59 (OP)
Newbie
Offline
Activity: 10
Merit: 0
|
|
January 04, 2015, 12:32:24 PM |
|
Now offering a 6 Dollars bounty...
|
|
|
|
|
notlist3d
Legendary
Offline
Activity: 1456
Merit: 1000
|
|
January 04, 2015, 06:29:52 PM |
|
Not working.
Any "hardware" solution via USB ? Or something like that
Not plain usb connection. There is serial connection (chances are you use usb for it). But not a plain usb to usb on controller board.` |
|
|
|
|
rafoute59 (OP)
Newbie
Offline
Activity: 10
Merit: 0
|
|
January 05, 2015, 11:08:00 PM |
|
Do you think I can buy a new controller card from bitmain?
|
|
|
|
|
notlist3d
Legendary
Offline
Activity: 1456
Merit: 1000
|
|
January 06, 2015, 12:55:34 AM |
|
Do you think I can buy a new controller card from bitmain?
Yes if it's out of warranty you can buy it from them. I believe it's 90 day's of warranty if you purchased from them direct (IE not ebay etc). Contact bitmain warrenty. |
|
|
|
|
hardhitter
Newbie
Offline
Activity: 24
Merit: 0
|
|
January 06, 2015, 09:46:49 AM |
|
Welcome to the club. The reset method post above does not work. I have 3 S3 miners and tried resetting them at least 25 times and there is no way to do it that I know of. Even bitmain states that if you forget the IP address you can never access the miner again. As far as I can tell the reset button doesn't do anything at all.c
From Bitmain: *** If you decide to change the AntMiner's IP address, Please Write It Down &
DO NOT FORGET
it.
If you forget the IP address, you will not be able to access AntMiner again. ***
|
|
|
|
|
rafoute59 (OP)
Newbie
Offline
Activity: 10
Merit: 0
|
|
January 06, 2015, 07:19:38 PM |
|
UP!
|
|
|
|
|
rafoute59 (OP)
Newbie
Offline
Activity: 10
Merit: 0
|
|
January 07, 2015, 06:18:57 PM |
|
UP
|
|
|
|
|
nwfella
Legendary
Offline
Activity: 1582
Merit: 1000
Well hello there!
|
|
January 09, 2015, 02:07:25 AM |
|
Welcome to the club. The reset method post above does not work. I have 3 S3 miners and tried resetting them at least 25 times and there is no way to do it that I know of. Even bitmain states that if you forget the IP address you can never access the miner again. As far as I can tell the reset button doesn't do anything at all.c
From Bitmain: *** If you decide to change the AntMiner's IP address, Please Write It Down &
DO NOT FORGET
it.
If you forget the IP address, you will not be able to access AntMiner again. ***
Factory default setting for IP address on S3's is 192.168.1.99, so, when you depress (and hold for a good 15-20 seconds), BTW, make sure your doing this while it is running (also, give it 3-4 minutes to fully bootup before pressing factory reset button), it should reset back to default. |
¯¯̿̿¯̿̿'̿̿̿̿̿̿̿'̿̿'̿̿̿̿̿'̿̿̿)͇̿̿)̿̿̿̿ '̿̿̿̿̿̿\̵͇̿̿\=(•̪̀●́)=o/̵͇̿̿/'̿̿ ̿ ̿̿
Gimme the crypto!!
|
|
|
|
