|
NoahWL1 (OP)
|
 |
January 20, 2015, 12:30:02 AM |
|
Hi! I recently purchased a used Antminer S3 from eBay, never overclocked, run in a clean environment. I've been running it for a few days now and I've noticed that the readings are always just around 400 GH/s on average, which seems to be a bit too little for me. On Bitmain's website, they say it runs at 441 GH/s +-5%, which still should leave me with about 420 GH/s at the very least. I am running at a clock speed of the default 218, all chips are working according to the web interface. Temperatures never go over 37 degrees. Am I doing something wrong, or did I just get a bad miner? Is there anything I can do to increase the hashrate? I cannot overclock, as my PSU only has 2 PCI-e connectors. Thanks.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
"There should not be any signed int. If you've found a signed int
somewhere, please tell me (within the next 25 years please) and I'll
change it to unsigned int." -- Satoshi
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
Zich
Legendary
 Offline
Activity: 1190
Merit: 1000
|
|
January 20, 2015, 12:35:07 AM |
|
Hi! I recently purchased a used Antminer S3 from eBay, never overclocked, run in a clean environment. I've been running it for a few days now and I've noticed that the readings are always just around 400 GH/s on average, which seems to be a bit too little for me. On Bitmain's website, they say it runs at 441 GH/s +-5%, which still should leave me with about 420 GH/s at the very least. I am running at a clock speed of the default 218, all chips are working according to the web interface. Temperatures never go over 37 degrees. Am I doing something wrong, or did I just get a bad miner? Is there anything I can do to increase the hashrate? I cannot overclock, as my PSU only has 2 PCI-e connectors. Thanks.
What is your psu brand & type? |
|
|
|
|
|
NoahWL1 (OP)
|
|
January 20, 2015, 12:57:01 AM |
|
I was a bit low on money, so I just picked up a Sentey 625 watt PSU and I'm using that. I also have a Corsair CX-500 running my overclocked Antminer S1 (I don't have to worry about power costs). Would that be better? I was planning on trying later tonight.
|
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
|
January 20, 2015, 01:12:38 AM |
|
I was a bit low on money, so I just picked up a Sentey 625 watt PSU and I'm using that. I also have a Corsair CX-500 running my overclocked Antminer S1 (I don't have to worry about power costs). Would that be better? I was planning on trying later tonight.
I hate to say this but that is crap psu dude. Amazon customer review all reporting problem. |
|
|
|
|
|
NoahWL1 (OP)
|
|
January 20, 2015, 01:17:20 AM |
|
Oh, dang. That's a shame I guess. I'll switch PSUs over. I don't care about the S1 as much since it draws more power anyways. The reason I got it in the first place was because someone else running the same set up as mine had the 725 watt version and was able to run an S3+ and the new R-Box 2.0 off of his, no problems. Guess I'll just have to deal with what I have and make the best of it. Thanks for your help.
|
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
|
January 20, 2015, 01:29:44 AM |
|
Oh, dang. That's a shame I guess. I'll switch PSUs over. I don't care about the S1 as much since it draws more power anyways. The reason I got it in the first place was because someone else running the same set up as mine had the 725 watt version and was able to run an S3+ and the new R-Box 2.0 off of his, no problems. Guess I'll just have to deal with what I have and make the best of it. Thanks for your help.
No problem dude  Let see how is the performance after changing better psu. |
|
|
|
|
|
NoahWL1 (OP)
|
|
January 20, 2015, 01:51:41 AM |
|
Switched out the PSUs and the S3 only ran at something like 13 GH/s. At least that's what it said in the average. It had solved 60 but rejected 500 in the few seconds I had to open the interface. Let it run for another few minutes, no change. I just figured it didn't have enough power even though it should; 450 watts on the 12 volt rail and the S3 only takes 355. Oh well. I switched back the PSUs and... worse? .19 GH/s... Fantastic... Letting it cool down for 10 minutes, that always seems to fix any problems I have. I'll see how it does from there. Hopefully I didn't damage it, I don't see how I could have.
|
|
|
|
|
|
NoahWL1 (OP)
|
|
January 20, 2015, 01:54:18 AM |
|
Although the S1 ran fine on the Sentey PSU. No problems at all. Same as the Corsair I had been using for months.
|
|
|
|
|
|
NoahWL1 (OP)
|
|
January 20, 2015, 02:41:16 AM |
|
Reset the S3 to factory defaults. Seems to have fixed that problem. I'll let it run for a day to get another average to make sure and then try to switch the PSU again.
|
|
|
|
|
MyRig
Donator
Hero Member
Offline
Activity: 792
Merit: 510
support@myrig.com
|
|
January 20, 2015, 07:57:19 AM |
|
for the bitcoin Miner, please select 80 Plus gold or plat. Little investment into the PSU makes a bit difference in a long run Reset the S3 to factory defaults. Seems to have fixed that problem. I'll let it run for a day to get another average to make sure and then try to switch the PSU again.
|
Antminer & DragonMint Repair E-mail: support@myrig.com T: @MyRig_com Return Address: MyRig 3700 Quebec Street, Unit 100-239, Denver, Colorado 80207, USA |
|
|
|
NoahWL1 (OP)
|
|
January 20, 2015, 09:27:05 PM |
|
Yeah, I've noticed :/ Not a good PSU. It's only running at 366 GH/s now. Thanks for the info.
|
|
|
|
|
|
