its starting to look like the best I'm going to get out of these things 12 miners in dual mode is ~1100khs scrypt. I have to admit, I'm a bit disappointed in this.

I'm currently away form their location so the best I can do is unplug them and plug them back in over the internet (disable in device manager, then re enable). Not sure if that will work but I'm going to try.

If I cant rectify this I might go back to CPUMiner and see if I can get CGMiner to see more than one at a time.

When I only had scrypt working the 12 miners were close to 3,000khs. I wonder if these things cant do both at full speed? I'm not in the same location as the miners so I cant check them for heat or power draw right now.

Well, since the web GUI that the controller puts up isnt worth a s*** I cant tell what they are actually doing but my BTC pool shows 128ghs and my LTC pool shows 1,225khs. Seems like I need to give the LTC pool time to catch up.

looks like using the private IP address of my BTC pool fixed the non BTC mining.

Mining both LTC and BTC with 12 grids right now!

Tried that on Friday. I couldnt get Windows to see more than one miner at a time.

I belive they will mine any scrypt coin but I have not tried anything other than LTC.

Zoom, the interface on the controller you guy sell is garbage. The lease you could have done was to have these things flashed to english so we can better understand what were looking at.

The miners seem to be mining LTC but not BTC. Need help.... Anyone have any ideas?

I went and picked up my second order of grids from Zoomhash yesterday. This group came with a controller (not in a case) with a little sd card in it. I managed to get into the controller to change pool settings but none of the miners are mining.

Anyone have any pointers? The controller GUI is in Chinese so I really have no clue as to what its saying.

FWIW, I'm trying them in dual mode.

Nice, gota try this tomorrow. I've only been able to get one to connect at a time so I went back to CPUminer. 

Anyone else try the already compiled version of cgminer for windows that can connect to the gridseeds? I was able to get it to connect and mine with one at a time but never anymore than that.

Not really...

All sold.

I'll match 1.16.

http://www.ebay.com/itm/261415611953?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

5 sold, 6 left.

FYI.

All miners have also been listed on eBay.

Hello all.

I've decided to sell my 11 Antminer S1's. Asking $750US in BTC equiv (coinbase.com) each shipped to lower 48, everywhere else will have to pay for shipping. Shipping to lower 48 will be UPS ground in original packaging. They all have the PCIe power connectors.

No power supplies will be sold with the miners. I've had them for a few months and they have all worked great.

Escrow will be done by gweedo, buyer to pay his fee.

FYI, I'm NOT a fan of shipping overseas. Its a huge PITA but I will do it. I will not, however, lie on the customs documentation about value so dont ask.

very informative thread! 

Dont know yet. The miners I bought shipped without their controller so I've been mining with them in Windows. But, in Windows, they run in dual mode and you cant turn off the SHA cores. I would imagine that they would run just fine in scrypt only even without a fan but I'm not trying that until I get a controller or connect them to a linux rig where they can mine in single mode.

FWIW, the 4U case I put 8 of them inside of has 6 120mm fans on the incoming air side and lots of air holes on the backside. Didnt matter much to these things, they got warm quick. I took the lid off of the case and they are fine now.

I'm going to find another permanent home for them outside of the case. The 3 I have sitting out in the open stay so cold that you wouldnt notice that they were running if it wasnt for the fans!