SP is there an  cpu  priority  0        ?

I notice that every since you have this intensity  and X in the build.. that maybe is what is  causing my  2 core rigs to crash on changing algo's every 6 minutes or every hour doing one algo.
If I have to put intensity settings in then the hashrate goes back down to where it was before the improvements.
It only happens on my 2 core

is there an  cpu  priority  0 setting ? thx

How the fck do I get ccminer stabilized on a 2 core ?

crash  ccminer crashed 10:38
11:08

Sp sorry  that was  1300 watts  not 1200. It just kicked off fans not spinning enough and I have it plugged into a spike protector that maybe kicking it off .. which is build into the psu.. now plug directly into the wall see if that works.
EDIT: Anyone know of a fan control for psu's plz  thx

Thx sp  it did cut off one time yesterday  but it is rated 1200 continuous 1300 spike from what I remember.
But that 90% because platinum rings a bell.
Just did a 20 min run on most algo's went smooth no oc'ing and no intensity setting  just need fan curve and temp control.
Just ran it at 1060 for 20 minutes. See what happens in a while and I will oc for a try to 1100 to see but now i'm going to stop oc'ing especially with summer coming.
Just got msi afterburner ... that is what i'm looking for just like the old evga.
EDIT: 90% efficiency so I think it can do 1200 watts but i'll have to read on it again.
And the psu fan should be faster. But I can't find a speedfan that would do it.

Sent you a pm 

Thx pallas but I can't compile. At least right now got alot of work to do on conf files ect.
But I wish sp would leave that to us... cpu affinity  1 ..2 ..3  4  ect  Unless  cpu affinity 1 will over ride that?

Thx I'm at stock everything p2 state  and getting 675 kh/s neo  sp5 970  and running smooth  no crashes ... I think nvidia inspector may have been part  not sure yet.
I think everyone is using MSI AFTERBURNER i'm giving that a try if it will take 5 cards  2x 980ti 2x970 and one 750ti on this rig. I know those gpus are running hot. so msi. 1050 watts at the wall.
Funny cpu you mentioned.

Yes I'm trying  all at default but the cards will burn up when room temp rise.. I think the default temp is 85 degress  
I need to monitor temp and have a fan curve.  right now everything is set default even intensity.  getting  18 mh/s quark 970 with 10.18.13.6143  driver

N.I. may have been part of the problem too

intensity settings ..... now does not validate on cpu   970 is 22

-d 0,1,2,3,4  -i 0,0,22,22,0

And why doesn't nvidia inspector remember oc on reboot?

Thx  I am.... now what I need is a fan control oc'ing app  nvidia insp. doesn't have fan curve.. use to use evga  some say msi  but evga prex won't take 5 cards . dont know what to get
ps i rolled back the drivers to the ones that worked best  from January

EDIT: have to do p0 state  ni wont allow temp control   think i'll get ride of the peice of s#@%

970 rig just crashed adjusting intensity ...  now does not validate on cpu crash  reinstalling different drivers.
Trying to keep out with all the crashing while changing intensity and miner control is stealing part of my hash on my small rig and...............
I'm thinking of starting over on the 970 980ti rig and leave it in the p2 state.. to much work to reset clocks that should be in the p0 state to begin with .. nvidia......

Sp please in the future make the default intensity settings lower ... I have to do all my bat files over ... that is also why my other rig is crashing. And to put that extra work in is a pain for me will take all day... I'm disabled..  type with a mouse onscreen keyboard.
sp5
The 4 core computers don't need anything done but the 2 core has to have it done.

Read my last 10 posts... and I'm sorry I don't have time for tests  even though I have a watt meter at the wall.. been delayed... I have to do all my conf and bat files over because of intensity settings that should not have to be made.
I'm trying to keep my rigs going  ... crashing while I'm adding intensity settings to stop it.

THANKS everyone for helping me.. very much appreciated  That hashrate on the 970 was at stock clocks.. it was doing 19 mh/s but unstable .. needed to set the intensity of course... it was the 970 causing the problem I think and so far it hashed overnight without crashing ..

PS anyone know how to open up a command window separate from an app using ccminer like MinerControl .. I need to see it like opening a reg ccminer window.  thx

On the 970 I'm getting 700 kh/s. sp 5 private.    = to 3.5 750ti. The best one you have so far sp for ALL algo's.

I don't think so... I do have them set at p0 for any algo but thinking of just letting them stay at the p2 state.

Yours are maybe in the p2 state. Mine are 3505,1455 in the p0 state.
I set my clocks to nvidia-smi -ac 3505,1455
When I have just one 970 it shows those clocks... but with 2 cards it showed 3505,1519  strange.
But I still set them as above even though one could be set higher.
Below is something someone gave me.
-----------------------------------------------------------------------

It is possible to oc the mem clock beyond nominal value, I use this command nvidia-smi.exe -i 0,1 -ac 3506,1506 (where i is the card number and ac the highest clock possible) this force the card to run in state 0

1) open cmd.exe with the admin privileges
2) cd C:\Program Files\NVIDIA Corporation\NVSMI
3) nvidia-smi -q -d SUPPORTED_CLOCKS -i 0
4) nvidia-smi -q -d SUPPORTED_CLOCKS -i 1
3) nvidia-smi -q -d SUPPORTED_CLOCKS -i 2
5) nvidia-smi -q -d SUPPORTED_CLOCKS -i 4
6) nvidia-smi -ac 350X,14XX -i 0 (where 350X is that very first number printed after supported clocks-memory and 14XX one of those numbers printed after graphics

cd C:\Program Files\NVIDIA Corporation\NVSMI
nvidia-smi -q -d SUPPORTED_CLOCKS -i 0 | more

cd C:\Program Files\NVIDIA Corporation\NVSMI
nvidia-smi -q -d SUPPORTED_CLOCKS -i 1 | more
---------------------------------------------------------------------

Now that I know my clocks , oc'ing must be off to set them, I use this.
Open administrative cmd window and I paste and enter this. Remember, look up your clocks first.
Two of those cards are 980ti  same clocks.

cd C:\Program Files\NVIDIA Corporation\NVSMI
nvidia-smi -ac 3505,1455 -i 0,1,2,4

SP  what is the default setting on sp 5 private for quark 970 g1?
EDIT: Looks like 23.
So far lowering the intensity is helping.
EDIT: That may have been the problem....I never set intensity on my regular rigs.
Will see be tomorrow.
This is the way I have it... but its working on all cards on some algo's. downing all the hashrates...and some algo's ..just on the card specified.
-d 0,1,2,3,4  -i 0,0,14,14,0

Thx Schleicher... that is one thing out of the way... trying intensity settings now.