Kann man Ripple mittlerweile auch woanders erstehen oder immernoch nur per Bitstamp-Ripple Connection?
Bei Kraken z.B. kann man Ripples handeln! OK, werds mir mal anschauen. Thx!
|
|
|
... P.S.: spaßeshalber habe ich am 17.01. mal einen BTC für EUR verkauft und Überweisung auf mein Bankkonto in DE angeleiert. Ich warte. Wird wahrscheinlich "pünktlich am 07.02. auf deinem Konto landen, SEPA-withdrawals liefen eigentlich immer reibungslos, nur die >20 Tage-Regelung je Withdrawal und Begrenzung auf 1000€ nach normaler Verifizierung sind halt das Nadelöhr. 2 Monate läuft nun schon mein Versuch Trusted zu werden, habs nun aufgegeben...Oha! Ich hatte gerade vor trusted zu werden und den Notarkram in die Wege zu leiten... Hat du denen die beglaubigte Übersetzung geschickt und seit zwei Monaten ist Funkstille oder wie?
|
|
|
Kann man Ripple mittlerweile auch woanders erstehen oder immernoch nur per Bitstamp-Ripple Connection?
|
|
|
I think i might sell for $20k. Dont think id sell for 20 btc.
Thx
How is that Lambo doing?
|
|
|
Hi Phil,
i am running 5 BJs at the moment via laptop and cgminer 3.12.
Whats the update situation in case somebody isnt using rpi/minepeon? Firmwareupdates manually?
Greets
ImI
|
|
|
Any deliveries today?
yes
|
|
|
reaching now 12h avg. 715 at pool with 1x241 (8vrm) and 3x251(2x 8vrm+ 4x vrm) oct.
nice! what amps/temps do you get? very mixed volt 0,09 - 0,13, amps 55-59, spi 3,1v spi clock 307200 Hz, temps 38°C-55°C, with heatsinks on vrms and with a tower big fan blowing from the top to the bottom of the case...the airflow is splited than under and over the asic boards... hw 0,8-1,1% r 0,05% WU ~9870 use one like that http://aquanaturalzone.com/images/t2.jpgit is laying at the top and the middle of the miner with medium blowingpower level so every part is "only" warm 847 watt on the wall (without big fan) with P&C 1200 MK III platinum 99.2 FW using cgminer enough information? yes. good job btw!
|
|
|
Hi all,
Seasonic Gold 1250W PSU seems to dislike overclocking.
The PSU shuts down immediatelly after cgminer restart. I think its some kind of overload protection.
So, what PSU should one buy for a November Jupiter? What pSU are you running?
I thought about a Corsair 1200AX or a 1500W Silverstone.
these are really solid https://www.nzxt.com/category/products/36-hale-90-v2-power-suppliesi saw your link and already looked out for those. do you use them with an overclocked november unit?
|
|
|
Hi all,
Seasonic Gold 1250W PSU seems to dislike overclocking.
The PSU shuts down immediatelly after cgminer restart. I think its some kind of overload protection.
So, what PSU should one buy for a November Jupiter? What pSU are you running?
I thought about a Corsair 1200AX or a 1500W Silverstone.
|
|
|
reaching now 12h avg. 715 at pool with 1x241 (8vrm) and 3x251(2x 8vrm+ 4x vrm) oct.
nice! what amps/temps do you get?
|
|
|
I'm thinking that the MPP or upgrade boards may be shipping... I'll have more to say by 10:30AM tomorrow.
Exciting! Perezoso, have you received all your initial B1 ordered units, so this could only be MPP? Looking forward to any information about the MPP. if there is really some mining-equipment sent it will be most likely the upgrade
|
|
|
von mir aus könnte man overclocken. das müsst ihr entscheinden und menig.
ich habe bisher zwei oktober jupiter welche zwischen 630 und 680 laufen.
ich vermute jedoch das menig kaum zeit für solche sachen haben wird.
|
|
|
definiere "peak performance" Maximale Leistung hehe! nicht übersetze sondern DEFINIERE. kleiner unterschied.
|
|
|
definiere "peak performance"
|
|
|
Do you think the new specs will make us less attractive to multipool/autoswicthing pools?
PHAD.
yes, the new specs mean less inflation. and less inflation equals less mining intention.
|
|
|
shouldnt WATT be more important as A? in the end its the wattage that leads to temperature.
In a "normal operating range," yes.. but as you get to the design limits and beyond, it is the current that makes a board melt, not a watt. For example - properly insulated, you could push 40,000V at 1A through a thin wire, getting 40,000W in the circuit, and the wire would live. But if you reduce to 1V and tried to get 40,000A through that same wire, the wire wouldn't live. That's why power distribution lines run at a very high voltage, to keep the current within the wire's limits. Hope that helps. thx!
|
|
|
If the gh-speed doesnt start initially from high value, then miner settles down to lower value. This is strange but perhaps there is some "initial modification" done on cgminer that sets the rate for rest of the session.
Sometimes i have to restart like 10 times to get this "high catch" effect. Its pain to wait in between, because without delay you just get fault 96/97 on vrms. Which means restarting the miner from the page (I dont like to switch off power but had to do that some times)I always wait like at least 45 seconds if vrms have been running for a while to let them cool down.
I've noticed that too, but my unit almost does it every time...if you mess with the spi freq. that can do it i think...cause i just increased mine and it didn't do it anymore...went back to stock and it did it again... well on 251 with oct. jup...thxs to the graph i was able to finally get the hw error down to .4% and 718-723gh/s on cgminer, bertmod says 700w same as 241, but that was before better cooling fans added.. .have one board at 240a :O hope it doesn't fry..and also 1 board at 200a but its at 42c Hopefully pool will report higher hash now that i got the hw % down i'll know morrow morning shouldnt WATT be more important as A? in the end its the wattage that leads to temperature.
|
|
|
I dont think so. And that could very easily hurt meows. Ahh you want cheap meow? Sell panic! FUD. Worth a try I guess. i already got cheap meows but think about it. this runup is partly due to expectations that kaiser will promote meows tomorrow in his show. alot buyers are in meow cause of kaiser. and what do you think will happen if kaiser says tomorrow: "look here is kaiser coin, forget about doge and forget about meow."
|
|
|
Whats more important for the safety of those VRMs? Ampere or Watt?
I have one VRM with 60A and 46Watt.
|
|
|
|