|
I will admit this is an interesting concept and I'll be paying attention to this. Good luck with your launch later, hope it's smooth and without trolls.
|
|
|
|
Dev,
I am still waiting on a transfer from Polo to the wallet. Been waiting for about 2 hours now. Any Ideas?
Check under the "Balances" tab on Poloniex. Does it say deposit pending? I think he's tried to withdraw from Poloniex to his wallet. e9800 Backup your wallet.dat asap I asked OldManKidd to look into it. He replied and said there is nothing pending. I still do not show a balance in my wallet. I can get you my transaction ID if that helps. Has anyone else successfully made a transfer? I sent a test 5 Mil from pool.mn to Polo and it went through fine, but this wasn't until after the updated wallet came out. |
|
|
|
Dev,
I am still waiting on a transfer from Polo to the wallet. Been waiting for about 2 hours now. Any Ideas?
Check under the "Balances" tab on Poloniex. Does it say deposit pending? I think he's tried to withdraw from Poloniex to his wallet. |
|
|
|
Updated Windows (Mandatory only for those on the wrong chain): https://mega.co.nz/#!ZxElQSbK!HTqoclXIt4jh-2CqNJa5rQwaw4UKYSPXcNFKrxJYMYw
Delete the old blockchain and re-install Wanna add addnode=184.173.115.98 to your conf  I added your node in, syncs in about 5 seconds to the correct fork. Thanks to both you and the dev. |
|
|
|
Well, we now have THREE different wallets downloaded and installed on THREE computers on different networks and they ALL show block 136.
Explain that, dev!
And we are using the conf provided by dev.
Looking into it.
Current block: 214I am using the conf that YOU provided and my wallet shows block 147. Because the wallet is on a shorter fork. I'm trying to add nodes, just waiting for wallet to re-sync to get the wallet on the right chain. The original chain got forked to pool.mn. |
|
|
|
That goes for me too, I have two co puters with the wallet showing block 138 now, all installed according to dev's instructions...
I would really like to know how this is possible.
Because the wallet is on the wrong fork. The pool.mn chain is correct, so try adding some nodes from the 50+ Rubberpool just added. How do you know that? How do I know pool.mn is on the right chain? Because every time dev tells us what block we're on, I refresh pool.mn and it's the same |
|
|
|
so what pool IS on the correct fork?
Pool.mn |
|
|
|
That goes for me too, I have two co puters with the wallet showing block 138 now, all installed according to dev's instructions...
I would really like to know how this is possible.
Because the wallet is on the wrong fork. The pool.mn chain is correct, so try adding some nodes from the 50+ Rubberpool just added. |
|
|
|
Current block: 189
So pool.mn is on the right fork. But the wallet isn't. We need more addnode to get the wallet on the right chain. |
|
|
|
wooow,dudes from pool.mn, very high transsction fee...
Pool.mn is on wrong fork. No. They are on the correct fork. There should not be any wrong fork if you use the .conf in the OP. pool.mn is at block 177! My wallet is at block 110, cryptopool.eu is also at 110..So And? Pool.mn has the longest blockchain and 99% of the hash. Why would they keep a less blockchain with hardly anyone on compared to a long blockchain with almost everyone on. |
|
|
|
wooow,dudes from pool.mn, very high transsction fee...
Pool.mn is on wrong fork. No. They are on the correct fork. There should not be any wrong fork if you use the .conf in the OP. dev, I want my 200000 ICD block   So the 200,000 coins that Polo already has is also in your wallet... yeah that doesn't work. So yes, you hit the first two blocks but you're obviously on your own fork. If that wallet syncs with the 200k in it, then it's yours, but that wallet will not sync. |
|
|
|
How can we be at block 160 already? If there is a block every 30 second, we should eb at about block 80, maybe a little more...
My wallet says block 100...?
Pool.mn first 7 blocks (62-68) took 8 seconds, so yes it's possible. All those saying pool.mn is on the wrong fork, the largest hashrate always controls the coin as it has the most hash and users. We need to get a node from Rubberpool so everyone else can get on to the right fork. |
|
|
|
Nice start....
Already Forked
i igree.... i think coin already forked! Yeah wallet is 50 odd and pool.mn is past 100 |
|
|
|
first 100 blocks have 0 reward to prevent instamining!!!! btw my wallet is synced!!! server=1
listen=1
rpcuser=user
rpcpassword=pass
rpcport=35551
addnode=108.61.198.32 use millionairecoin.conf in your Roaming folder! Actually it's only 100 blocks not 300. [CHMinePeerz Ninja edited before I could hit reply] |
|
|
|
100blocks, no coin.
(0.00000000 MIL Est Earnings)
First 100 blocks was 0 coin to prevent unfair launch... |
|
|
|
yes ,I always mined at this pool , good pool +1 +1 great start Fastest I've seen a pool up recently, good start |
|
|
|
As long as my BTC gets it's first confirmation, my first ever rental will be pointed here, hope everything goes smoothly |
|
|
|
Wallets Available
Awesome, can we have RPCport, roaming folder and conf name please. At launch  Ok Just to give you a heads up, the latest version of chrome won't allow you to keep the wallet as it detects it as malicious. Really? Its in a zip file and chrome does not mark ANYTHING in a zip as malicious. Never heard of it before Anyway, do not worry. There is nothing malicious in there, you can check it on virus total once we release the passwords. It's happened to every wallet download of the last week so this is an issue with all QT wallets not just this one. |
|
|
|
Wallets Available
Awesome, can we have RPCport, roaming folder and conf name please. At launch Ok Just to give you a heads up, the latest version of chrome won't allow you to keep the wallet as it detects it as malicious. |
|
|
|
|
Show Posts
