Show Posts
|
Pages: [1] 2 3 4 5 6 »
|
can i email or pm a site monitor? i cant find a link to pm or email.
|
|
|
WHERE CAN I SEND YOU MY MONEY? !!!!!!!!!!!!!!!!!!!!!! I just got $20,000,000 from some Russian prince I didn't know had me as a benefactor. I want to blow it fast!!!!!!!!!!!!!!!!!!!!!!!!
|
|
|
i just updated my wallet. it shows i have 11460 transactions. but no coins. the blockchain is 37% done. shouldnt i have seen at least one coin by now? do i need to put a conf file in the zeitcoin dir?
Nope , the balance will not be correct until it is fully synced. After it is fully synced. If your amount of Zeitcoins is off, click on Help, click on Debug Window, and click Console Tab, type in repairwallet and hit enter. FYI: _________________________________________________________________________ ok thank you ill check back tomorrow when i wake up thanks
|
|
|
i just updated my wallet. it shows i have 11460 transactions. but no coins. the blockchain is 37% done. shouldnt i have seen at least one coin by now? do i need to put a conf file in the zeitcoin dir?
|
|
|
just updated my wallet and now i cannot sync?
ok never mind it just took FOREVER to connect.
|
|
|
just updated my wallet and now i cannot sync?
|
|
|
I have had no payouts for 2 days but hashes are still being accepted for x11 minerpools and suchpool.
at suchpool i watched the round progress bar climb then past 79% then drop back to 44%.
anyone else have this problem and found a solution?
|
|
|
I havent heard any replies about not being able to sync on client. its been over a day since i updated and i cannot sync even though i have connections
|
|
|
If we continue this way we run very high risk that MintPal closes us the ZEIT market anytime! :S they might just open it as a ltc market anyway its on cryptsy so not to worry too much
|
|
|
just updated my client and it doesnt want to sync. ive reopened it a few times and waited up to half an hour. my coins are there at least
|
|
|
There are some decent paying Scrypt-A-Nfactor orders ... if you have Scrypt-A-Nfactor you can get some good payouts, check here: https://www.nicehash.com/index.jsp?a=2 and point your miner to stratum+tcp://stratum.nicehash.com:3335 We advice you to use multi-algorithm configuration (if you're using latest sgminer) "pools" : [ { "name" : "NiceHash Scrypt-A.-Nfactor", "url" : "stratum+tcp://stratum.nicehash.com:3335", "user" : "myBTCaddress", "algorithm" : "nscrypt", "nfactor" : "11" }, { "name" : "NiceHash Scrypt", "url" : "stratum+tcp://stratum.nicehash.com:3333", "user" : "myBTCaddress", }, { "name" : "mybackuppool", "url" : "stratum+tcp://mybackuppool", "user" : "myBTCaddress", "pass" : "x" } ] , "kernel" : "zuikkis", ... etc ... I have added my info to the conf file but i get errors when loading partial JSON error in conf file conf file could not be used need to specify at least one pool server Make sure you have commas where there needs to be and no commas where there doesn't need to be. Also, same with the brackets. I get that message when I've messed up those. thanks but i dont know how to do that. i want to setup for Nscrypt but if i change my port to 3335 i get share is above target. i followed the faq on the nicehash website. it works fine in scrypt mode with this bat with no conf file. setx GPU_MAX_ALLOC_PERCENT 100 sgminer -o stratum+tcp://stratum.nicehash.com:3333 -u 1CrpGPyvWdGuirFTN7ky62bLvYEW1gZUuZ -p d=64 -o stratum+tcp://useast.wafflepool.com:3333 -u 1CrpGPyvWdGuirFTN7ky62bLvYEW1gZUuZ -p password --thread-concurrency 8192 --intensity 13 --worksize 256 -g 2 --temp-target 70 --gpu-memclock 1500 --gpu-engine 1080 --gpu-fan 80
|
|
|
There are some decent paying Scrypt-A-Nfactor orders ... if you have Scrypt-A-Nfactor you can get some good payouts, check here: https://www.nicehash.com/index.jsp?a=2 and point your miner to stratum+tcp://stratum.nicehash.com:3335 We advice you to use multi-algorithm configuration (if you're using latest sgminer) "pools" : [ { "name" : "NiceHash Scrypt-A.-Nfactor", "url" : "stratum+tcp://stratum.nicehash.com:3335", "user" : "myBTCaddress", "algorithm" : "nscrypt", "nfactor" : "11" }, { "name" : "NiceHash Scrypt", "url" : "stratum+tcp://stratum.nicehash.com:3333", "user" : "myBTCaddress", }, { "name" : "mybackuppool", "url" : "stratum+tcp://mybackuppool", "user" : "myBTCaddress", "pass" : "x" } ] , "kernel" : "zuikkis", ... etc ... I have added my info to the conf file but i get errors when loading partial JSON error in conf file conf file could not be used need to specify at least one pool server
|
|
|
So how does the POS work. Ive kept the coins in my wallet and Ive not seen any interest yet. How often is it calculated?
|
|
|
Looks legit where do I post my bank account and credit card info?
|
|
|
Password? 4 minutes past launch time.
lol i tried pw logicoin just incase but thats not it
|
|
|
How to solo mine on a GPU First you'll want to download and unzip sgminer from https://mega.co.nz/#!2JYXHDpD!OOiFOdsh5rnvk1zhz5niXENNzbgnw1UXwmFcicBzevI Then you need to make sure that you've copied the logicoin.conf into your appdata/roaming/logicoin directory. Once you've done that you should open notepad and paste the following into it. sgminer.exe -k darkcoin -o localhost:9652 -u user -p password Now save that as logicoin.bat inside your sgminer folder. Make sure that when your saving it you have "Save as Type" set to "All Files" Now make sure the wallet is running and then simply run the .bat file you created above. do you have to put the qt in server mode?
|
|
|
did you shut down? i cannot log on i still have coins there
|
|
|
i like the design of this coin hope the launch goes smooth
|
|
|
We don't use pennies here in Canada anymore, how about nickels? if your loose enough for them go for a tw oonie The second O is redundant as "two" already makes an "oo" sound It also doesn't have a w, plus his double "oo" is right all wrong 2 o's no w http://en.wikipedia.org/wiki/Toonieanyway my point was that Toonies are bigger so they have more assvalue.
|
|
|
|