i have a wallet on the binance smart chain that has been compromised. im looking for a bot/script that can automatically send the rewards/claims of a "certain token" from that wallet to a different address faster than a human can

If you are a newbie please do not respond.

Hello all,

I have a shed that was used for mining that i need to sell. Its located in Orlando Florida. The shed was bought new by me. Its 10x30. As you can see in the pictures i have added 13 exhaust fans of various sizes. The shed is wired with 48 outlets at 240v and 5 120v outlets for the lights, network gear etc. It also has built in surge protectors for all the outlets. I have 2 underground rated cat cables running into the shed as well. As you can also see from the pictures i have 31 ventilation cutouts in the floor to pull in fresh air. At one point i had close to 400 video cards and a hand full of ant miners and in the middle of the Florida sun the ambient temp in the shed was no more than 90 degrees Fahrenheit.

The shed is fairly easy to move, it was literally drop off on the back of a trailer pulled behind a pick up truck.

If you are interested in taking a look at it or have any other questions please send me a direct message.

Pictures are below

Guys,

I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.

The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.

I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...

These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...

Im hoping someone out there has run into this prior....

Any help would be appreciated

Thanks

Guys

I have a strange issue with one of my rigs that i cannot figure out. I currently have 13 rigs but for some reason this one has been an issue for me

8 sapphire 570's modded 1500+ straps using PBE 1.6.3
asus z270-a
8gb ddr 4

2 EVGA G3 850's and 2 server PSU's

Im using claymore 10 and have used 10.1 ..using the latest amd drivers with compute turned on.

Windows 10 1703 build just like all my other rigs

the issue is that whenever i change any voltage settings in claymore and i reboot the computer the miner locks up the computer after it initializes the open cl...

once it locks up reboot it again and the hashrate is back at stock...reboot again and then starts working ok

another issue is that every minute or so i get a random card that drops the hashrate...2-3 hashes

ive tried lowering the clocks and slowly raising them but no luck

is this a Claymore issue ?

I have changed out the mobo, the DDR, the pci risers...currently i have 3200 watts available to it so i know its not a power issue....


Any help would be appreciated

Guys,

I have one card on one of my rigs that will not switch from graphics to compute on the latest drivers...i have rebooted countless times...nothing

Anyone else have this issue ?

Thanks in advance

Guys

im using claymore with my rigs...as always im trying how to maximize hash rate but keep electricity costs down

Im using the claymore commands -mvddc and -cvddc

i have used those in conjunction with the -powlim -xxx   but i do not see any difference when i add the -pow lim option

anyone have any thoughts they could share regarding which one would do the best job ?


...also read somewhere that the gpu and mem voltage is paired...meaning one cannot say lower the gpu voltage and not the mem ?

Thanks in advance

Guys,

Struggling with this card. Currently getting 27 with about 1150 watts at the wall with 8 cards.

Anyone getting better results ? Maybe this is all its got

Thanks

Guys,

not sure where to post this...

I am trying to use hashcat to "try" and recover my wallet. I have recovered the hash already with john the ripper.

My question is if anyone knows...the hash pertains to the passphrase of the wallet or does it pertain to the seed/keys ?

Using bitcoin core

Any help would be appreciated

anyone getting higher stales after the eth fork with ethermine...all of my rigs went from 1-2% to 5-8%

I have opened a ticket but nothing so far

And i have 2 locations with different IP's so i doubt its my network/router etccc

Thanks in advance

guys i have an issue...

i have one miner that whenever i restart the computer and run the miner's bat file all the hashrates are at stock...if i then open the bat file and simply save it and then start it its fine...any thoughts ?

Thanks in advance

Guys,

Need some HELP

Trying to mine UBIQ SOLO....

set up 1st computer with the node...even connect a miner on that same computer to the node with no issues...

trying to connect other computers on the same local network to the node...using the first computers IP address 192.168.1.54:8588

using claymore

im getting


ETH: http error #7.
ETH: Failed to connect to pool (192.168.1.54:8588), retry in 20 sec...


has anyone seen this before ?

I even opened a firewall rule with the 8588 port


Thanks in advance

Guys,

I have an issue with one of my rigs that i cannot figure out. I have

asus z270-a
6 GTX 1060's 6gb
2 GTX 1070

IF i start afterburner before i start the miner the computer freezes. I have switched the motherboard with a new one, the processor with a new one(G4400) i have switched the memory, i have re installed a fresh copy of windows 10, i have changed out my PSU's...I even added more than enough power to see if its a power issue but nothing....

The only thing i can think of is because i have 6 1060's and 2 1070's something is not working correctly at the start of claymore. I have also tried 9.7 and 9.8 and the ame thing happens....

Does anyone know if its possible to delay an instance of claymore by lets say 30 seconds ? I know how to run different instances but cannot figure out if it possible to delay one of them....

I want to be able to set it up so that if the rig restarts it can start running the instances with AB

Thanks in advance

Hi All,

Has anyone updated the bios on this board yet ? on the Asrock site they have listed a new one a few days ago but unfortunately it does not state what the updates are.

My internet speed is horrible with this board so im looking to update it if it helps

Thanks in advance

Hi Guys,

For the life of me i cannot get the fan settings to work. Im trying to not use afterburner. I am using 9.7 with modded RX 470's . Im trying to keep the temps no higher than 70 and the fan speed around 50

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100

EthDcrMiner64.exe -epool stratum+tcp://us.ubiqpool.io:8008 -ewal 0x926957F22b01b2E100078DF71Cf33377E0b0C9a9 -epsw x -eworker tampaminer-1 -epsw x -allcoins 1 -cvddc 875 -mvddc 875 -cclock 1170 -mclock 2040 -tt -50


Thanks in advance

Hi Guys

I don't understand why lowering the core clock raises the temps and the voltage on my GTX 1070's on afterburner.

Wouldn't it be the opposite ?

Hi All,

I have one rig with a weird issue.

Asrock H110 BTC+
6x GTX 1060's and 2 1070's
Calymore 9.7
372.54 drivers
Afterburner 4.3

In order to start claymore i need to make sure that afterburner is not running. If not it freezes windows. Same thing goes for shutting it down. Afterburner needs to be shutdown first

Any thoughts ?

This board is a pain

Thanks in advance

Guys,

I have over 10 asus z270-a's and decided to try the new Asrock H110 BTC+

After several hours i finally got this thing to boot properly(very glitchy at this point)

My issue is that the internet connection is super slow. I have researched it and it uses an Intel I219-V network adapter which of course a lot of folks have had issues with over the last few years in ASUS boards.

I have run the onboard diagnostics and it keeps telling me that the cable is bad or that the router and or switch is not set up properly.

Changed out cables, changed out switches etc...

Just wondering if someone has run into an issue with this network adapter in the past ?

Thanks in advance

I have a GPU that is acting up, its hashing way less than the others....i can see its not stable in afterburner.....but for the life of me i cannot figure out which one it is. I have 8 of them running

I hope someone out there has run across this issue and can shed some light

meaning is the first one on the board GPU 0 and the next is GPU 1 etcccc... ?

Thanks in advance

Hi Guys

how many GPU's can claymore handle at one time with only one miner running ? Meaning only one instance ?

Thanks in advance

Guys,

I have 10+ gtx 1070 rigs with 8 GPU's each but i came across a bunch of rx470 and this is all new to me.

I got them modded Sapphire RX 470 Nitro(non +)

they are happy at 28.5 but when i try and dual mine with SIA i get 600+ on sia and ETH drops to 12+- MH

I havent  added any - drc setting

Anyone have any ideas what im missing ?

Thanks in advance