Hello all,

I cannot for the life of me get cgminer working on any pool.  I get this:
http://postimg.org/image/se4zie1on/

The dashboard of whatever pool it it reports 0kh/s here are my .bat settings:

cgminer --scrypt -o stratum+tcp://eu.wemineltc.com:3333 -u Kinetic915.1 -p AidadC123 --shaders 1792 --intensity 20 --worksize 256 -g 1 --gpu-engine 1000 --gpu-memclock 1500 --temp-target 75

any ideas?

Thanks!

Hello all,

I am attempting to mine on wemineltc with cgminer.  I believe I have set up my bat file correctly, but when I start cgminer I get: Probing for alive pool then
Stratum from pool 0 found new block.  It says I'm doing something, but my dashboard brings up that I have a 0 hash rate, any ideas?

here is my .bat

Thanks!

color 07
cgminer --scrypt -o stratum+tcp://eu.wemineltc.com:3333 -u worker.1 -p password --shaders 1792 --intensity 20 --worksize 256 -g 1 --gpu-engine 1000 --gpu-memclock 1500 --temp-target 75

Hello all,

How do you build and run the most stable consistent system?  So far I have random crashes, random lag, my hash speed suddenly decreases by about 200 and stays there until I do something.... Any ideas?

Thanks

What happens next? When the difficulty is too high do you give up, try and compete or will there be something else on the horizon?

Hey all,

So do you guys buy extra warranties on your cards?  I've already made an investment on the rig.  Is it work the extra 100 dollars with the gpus running at 70 to 75 constantly?

Thanks!

I was connected with a CAT 6e cable directly to my router and was getting 1800kh/s litecoin, now i get 1700 or less with a wireless adapter.  Does the network connection affect the hash speed? Thanks!

Hello all,

I had to reimage my windows installation on my miner and when I got reaper running again I was only reaching speeds of 1675, before I was easily reaching 1800.  I am using the same settings and drivers and cannot figure it out.  Any suggestions?

Hello all,

Is using a x1 to x16 cable to install a fourth graphics card a good idea? lol  Would the motherboard even recognize it?

Thanks

Hey all,

I curretnly have my rig running from my laundry basket.  Can anyone suggest a good well ventilated case, preferably one where i can send all the heat and related vented ozone a certain direction?  I live in a small space and this would help much.
Thanks!

How bad is the burning smell of electronics for your health.  Obviously the miner I have going makes a bit of this smell.  I live currently in a small apartment and the smell normally predominates the entire apartment. 

Any suggestions?

Hello all,

I am currently using the python script to open and terminate reaper.  Is there a script I can use that can send me a email or something with the current temps of the GPUs on close?

Thanks!

I am currently using notroll, can anyone recommend their favorite pool and why?

Thanks!

Hey all,

I have 3 7950s connected to a Asrock extreme 6 board.  Any suggestions as how I would connect a fourth?

Thank you!

Hey all,

I've been having problems with the 3 pcie x16 cable extenders i purchased for my 3x 7950 rig.  When they are installed, either the motherboard doesnt recognize the graphics cards are there and doesnt post, or it consistently crashes/strange freezing.  Are these cables normally defective like this?  Any experience on this?  Any suggestions?

Thanks!

Hello all,

I just built my first 3x 7950 LTC mining rig.  Everything was perfect, but the cards were directly connected to the board, obviously a heating issue.  I ordered 3 PCIe x16 extender cables, and installed them.  Upon booting with the cables I was greeted with a host of problems, the board would not detect the cards and wouldnt post, when I finally did get through to windows I would continutally get the blue crash screen.  I disconnected the cables and am now running 2x 7950s with complete stability.  Question is, is this a normal occurrence with these types of cables?  Did I just get a horrible batch? Any expereince along these lines appreciated!  Thank you!