|
So currently I have 5 GPU's up and running with the modded Bios and with the mining drivers, but they only run at 22Mh/s each and the sixth GPU is still not working. When I plug the sixth GPU in the mobo alone, it only shows Intel HD Graphics, I think the GPU isn't recognized anymore, is that possible?
|
|
|
|
revert gpus to original bios
ddu from safe mode
try installing again
it should work then
there is problem when you install new drivers with modded bios gpus
Okay thanks! What drivers should I use to flash the original bios on the cards? Does this matter? When I have the original BIOS installed, should I install the Blockchain drivers first and only after this BIOS MOD the cards again? |
|
|
|
|
Bios settings are fine, I had 6 cards running perfectly fine until I started messing with the mining drivers.
I have 5 cards up and running now on mining drivers but they have a very low hashrate of 23,5 each with a slight overclock and Bios mod and the sixth card is somewhere in Nirvana, no clue why the PC doesn't recognize it anymore.
|
|
|
|
Tested DeepVault and it works perfectly. Will the fee decrease over time? 1 Onion is too much once the value starts to spike.
Better upload everything now than later  With upcoming improvements, I'm shure there will me more changes coming along. |
|
|
|
|
I uninstalled the drivers of my 6 GPUs with DDU and now I have 6 Microsoft Basic Display Adapters in device manager and all of them show error 31:
This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
The driver trying to start is not the same as the driver for the POSTed display adapter.
What should I do now? Note: All my cards are Bios modded.
I tried to install the blockchain drivers but amd installer doesn't detect any hardware and when installing the latest AMD driver for RX480, the installation stops in the middle of the process.
Since the last restart, device manager only recognizes 5 Microsoft Basic Display Adapters. I switched the Pcie cables and detected that the problem is with the GPU, it regognized 6 cards some hours ago and since my try to install drivers, only 5 devices are left.
Can someone help me to fix my problem please?
Rig Setup:
Hardware:
2 XFX RX480 GTR 8GB
4 Powercolor RX480 Red Devil 8GB
AsRock H81 BTC Pro Gen1
CPU G3460
120GB SSD Sandisk
8GB DDR3
Software:
Bios settings for PCIE2 Link Speed is GEN 1.
Running Windows 10 x64
Settings I've done:
Increase virtual memory (Min 1879 Max 16000)
Power plan --> High performance
Windows 10 registry tweaks for mining
Disabled windows update
|
|
|
|
|
Congratulations CryptoGrinder! Glad you made it! I guess you can't wait for friday to come.
|
|
|
|
I updated my wallet to v1.3 not long ago and very happy with DeepVault integration. It gives more value to this project. Excellent work. I wish DO to hit Bittrex in the near future. This great community deserves a good exchange.  We got the notification that "DeepOnion will me listed on a major exchange soon" some weeks ago, I wonder how long it will take. We dominated the pool for the vote to ne listed on Bittrex already, so that's a very good beginning already. Hope it won't take long anymore. |
|
|
|
|
Hardware:
The 6 GPUs are:
2 XFX RX480 GTR 8GB
4 Powercolor RX480 Red Devil 8GB
Motherboard: AsRock H81 BTC Pro Gen1
GPU G3460
120GB SSD Sandisk
8GB DDR3
Software
Bios settings for PCIE2 Link Speed is GEN 1.
Because I made a fresh installation of windows 10 x64 and the cards are not working fine I did not run Claymore yet with the new mining drivers, therfore I can't tell you the wattage yet.
Currently, the PC recognizes 5 RX480 with driver version 22.19.662.4 and all 5 with error 43. It also regognizes 1 Intel(R) HD Graphics.
I made some settings:
Increase virtual memory (Min 1879 Max 16000)
Power plan --> High performance
Windows 10 registry tweaks for mining
Disabled windows update
Then I ran DDU in safe mode and it still only recognized 5 devices. Now I switched PCIE5 and PCIE6 and magically the PC sees 6 cards.
Now I have 6 Microsoft Basic Display Adapters in device manager and all of them show error 31:
This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
The driver trying to start is not the same as the driver for the POSTed display adapter.
How should I proceed from this point?
|
|
|
|
Is your OS Windows 7? After everything I have try, until now I cant get Blockchain Driver works on Windows 7, thats why I change to Windows 10, and it works perfectly.
How many GPU does Windows 10 support? Up to 8 as far as I know. |
|
|
|
|
I reinstalled windows and wiped everything that was installed.
THen I downloaded the Blockchain drivers, teamviewer and ati patcher.
I did this with the mining drivers on my GPU's and the screen was lagging, I checked in device manager and only 5 cards showed up. To find if the error is in the hardware or software, I installed the latest AMD driver for my GPU and the PC recognized 6 cards. Afterwards I reinstalled the blockchain drivers (with AMD uninstaller, not DDU) and the PC regognized only 5 cards anymore and 1 Intel HD Graphics. Do I need to turn these Intel HD graphics off in the mobo bios settings?
|
|
|
|
I am advocating to use for the extraction of old equipment for 4 GPU. This gives substantial savings when buying a motherboard CPU and power supply. Two sets for 4 GPU will cost less than one set for 6 GPU. You can use any OS. Also you share the risks from the fact that your equipment will fail. In case of any problems with the equipment you will be half of the GPU or all 6 GPU will not work. Which option is better?
The rig has been working fine for over 6 months, I'm not going to spend more money when I already know that it can work fine. |
|
|
|
Is your OS Windows 7? After everything I have try, until now I cant get Blockchain Driver works on Windows 7, thats why I change to Windows 10, and it works perfectly.
Yes I'm on Windows 10. Currently I have some serious problems to get my rig started, it takes ages to start. If I can't fix that, I'll reinstall Windows 10 and start from the beginning I guess. |
|
|
|
I installed the mining drivers and I've run Pixelpatcher. All 6 GPU's show up fine in device manager. Afterwards I installed Afterburner 4.4.0 beta and RivaTuner. I run Afterburner but the program froze immediately, no way to end it. I restarted the rig to close the program and tried to run Claymore Miner v10. It gave me an error message that something's wrong with my screen settings.(I had plugged my monitor in the motherboard HDMI to update the drivers) so I put my HDMI dummy plug in the GPU that's connected to the x16 slot on my mobo. Then, Teamviewer didn't start anymore and I found out, that my screen and my hdmi dummy plug don't work anymore when plugged in the GPU and when plugged in the mobo, only the screen works, not the hdmi dummy plug. Any fix for that? This is the error message and the file that causes the problem. Should I delete the old files and only keep the 2 newer ones?   |
|
|
|
what kind of crypto currency can be mining on d3, except dash?
Check it out on this website: http://whattomine.com/asicSelect only X11 algo and put in the speed of your D3(s). 17000 Mh/s and 1000W power consumption and 1% pool fee and your electricity cost. |
|
|
|
Card keeps overheating. Nvidia, linux CUDA. Help  just mining on the supernova pool. Make sure the problem is not with the setup of your rig (cards to close together, not enough fresh air) or try to clean your cards, maybe they're dusty. The miner program itself doesn't cause overheating. Maybe you have some wrong (or none at all) overclocking settings which cause high GPU temps. |
|
|
|
Yes, it is amazing to see Deeponion leading. I strongly think we will win the vote with our strong community. Please vote everyone. Does that mean DeepOnion will be going to Bittrex? Devs will announce a major exchange after #deepvault releAse. A lot hodlers and supportees wish it will be buttrex. When will it be released? The team is testing #deepvault now before they make it public. Dont know the date but my guess is that we will see the release next 14-21 days. I am Just a supporter. Last week they posted in the forum that it will take about 2 weeks, so if we're lucky and testing went well we'll get it during the week now, maybe on Friday to double the happiness. |
|
|
|
|
Okay thank you very much for your answers.
I'll install the AMD Mining drivers and run PixelPatcher and hope it works fine with my modded bios.
I'ne not heard about the AMD Relive drivers 17.7.2 before in terms of mining, I guess the Blockchain drivers are far better anyway?
|
|
|
|
|
Hello mining community,
I have a mining rig with 6 RX480s and I want to get the highest hashrate I can get.
My cards are:
2 XFX RX480 GTR 8GB
4 Powercolor RX480 Red Devil 8GB
I have Bios modded the cards and the rig got a hashrate of 165 Mh/s on Ethereum. MSI Afterburner doesn't want to start since the cards are Bios modded (no clue what I did wrong to cause that issue). My Drivers version is currently 16.9.2.
Now my question is:
Should I reinstall the original Bios and install the new mining driver beta from AMD and overclock the cards
or
Should I keep the modded Bios and try if the mining driver work?
I switched from ETH to ETC yesterday and my hashrate dropped from 165 Mh/s to 135 Mh/s and I hope to get back to my usual hashrate or even more with overclocking and new drivers but I'm not shure how the Bios mod reacts to this.
|
|
|
|
Many thanks for your video! This makes it already a lot easier to cope with the installation of my first masternode. I'll hceck out the web on how to setup a VPS and next I'll follow your guide. Eventough it's your first, I hope it won't be your last tutorial |
|
|
|
|
Show Posts
