Seems their site is dead now...pointing to some educational website.
Dead for me as well so now there no where in the UK where you can get miners (some did work) I spoke to them late last night uk time and they said they where having web site issues before site when down for maintenance There is also a fake email doing the rounds offering 70% of the a2 miners be careful |
|
|
|
p2coins.com:9332 has 81% effie  Very bad node. Has been over 100% consistently till I restarted node recently and had a few mad 25Ths miners on. It will recover |
|
|
|
I run all my asics on the Odroid u3 from here http://hardkernel.com/main/products/prdt_info.php. which uses the Exynos quad core cpu. They run standard linux, don't have usb issues like the PI and run bfgminer, cgminer, minera and assorted other miners with no issues. |
|
|
|
I would avoid the beaglebone for now, it has a hot plus usb issue that doesnt seem to be fixed even in some of the beta kernels.. anyhow just my 2 cents since I tried to get one working and just gave up.
It's running fine for me on the 5-14 Debian firmware. Are you running an Angstrom release? The odroid u3 is a good alternative http://hardkernel.com/main/products/prdt_info.php I ditched all my pi for them due to usb issues |
|
|
|
Hey michelem
is there a way to monitor and restart the miner when a device goes down, i'm really having a hard time, i always have blade going down every few hours, and have to restart cpuminer to bring them back up.
it's not the hub, i've tried different hubs.
Try lowering the clock speed a bit worked for me on one fussy blade |
|
|
|
does the g blade mine x11 and or n-factor ?
NO scrypt only |
|
|
|
Hi I ordered late on the 28th and received my order today in the UK, fast delivery only issue is there are only 2 blades not 4  help can you look at order order No #1739 as its showing as complete on site. Thanks All sorted other 2 shipping monday |
|
|
|
Hi I ordered late on the 28th and received my order today in the UK, fast delivery only issue is there are only 2 blades not 4 help can you look at order order No #1739 as its showing as complete on site. Thanks |
|
|
|
I've been folding almost 2 weeks now. A couple hundred work units and 90k points. Nothing is showing in the cryptobullionmining dashboard. I sent an email to cryptobullionmining@gmail.com late last week no response that I've seen. Tried signing up on the curecoin.us board but it wanted me to verify team name and number. I didn't join a team yet so all I had was, Team 0 and no name. Thanks you need to be in the cure coin team to get paid on the pool from getting started on the pool here https://www.cryptobullionpools.com/gettingstarted |
|
|
|
Hi I have 3 mildly over clocked blades which have been running fine until today when one of them has blown on both blades the ferrite bead marked (what is the "a" for) afb26 next to the usb connector. Needles to say they don't work any more does anyone have any idea of A/ what the spec is for that component is and B/ The hard one any idea why this may have happened. The other 2 are hashing fine. Ken overheating can cause many components to fail. the other reason is a short somewhere on the board. maybe the upper gate mosfet could have died. check for continuity between pin 4 (gate) and the 4 pins soldered to the same pad (drain). It's been explained in the 5chips pod thread https://bitcointalk.org/index.php?topic=519112.msg6722468#msg6722468on the later blades, gridseed replaced the ferrite beads with zero resistors of the same 1206 size Well one is back working using one of the fb off of a bad 5 chip and all seems to be fine with it. Next to bypass the plugs and solder direct to pcb for power and moooreeee heat sinks  ) |
|
|
|
Hi I have 3 mildly over clocked blades which have been running fine until today when one of them has blown on both blades the ferrite bead marked (what is the "a" for) afb26 next to the usb connector. Needles to say they don't work any more does anyone have any idea of A/ what the spec is for that component is and B/ The hard one any idea why this may have happened. The other 2 are hashing fine. Ken |
|
|
|
|
Its not hard to put them back in and imo worth it to fix issues
As well as the issues mention in the least few posts the two buttons for guided and manual settings where greyed out for me.
I tried doing a clean install and also an upgrade and all the other suggestions none of which worked.
|
|
|
|
For people having issues with random errors i have found they flushing the redis db seems to fix them. Provided you are not using redis for any other apps ssh into your machine and do the following which will rest most of your settings The prompt will change to redis> then type and finally and restart Almost forgot you will need to re run the install_miner.sh again to repopulate the db |
|
|
|
I have one gridseed 5 chip miner and one gridseed g-blade. Can I run both of these miners off the same raspberry pi running minera?
yes you can |
|
|
|
|
I can vouch for him he has been very active in providing support for several pools.
|
|
|
|
|
I have changed united-miners to 30 confirms as well now
|
|
|
|
I can not see a cure coin pool at betahash.com |
|
|
|
United-Miners Cure pool is up and finding blocks https://cure.united-miners.com/Direct link to registration page https://cure.united-miners.com/index.php?page=registerWe provide all the usual features, but we aspire to be the best through support and lack of downtime. Stratum with Vardiff LOW fees, 1% or less! Email alerts for Down Workers High-End Dedicated Servers Gigabit Dual uplink on the EU's best internet backbone Active IRC community helping new users get started with mining 24/7 Support through IRC (#united-miners on freenode.net), or Contact Form DDoS Protection Forced SSL (encryption) for security Custom User Interface
|
|
|
|
And which panda pool is working now?
I was mining on united-miners and sending pandas straight from pool to mintpal exchange.
What I have to do now?
I don't have any local panda wallet.
When united miners or another pool will be fixed?
We are running 8.6.2 after reverting back to that from the updated wallet after the mess yesterday I am not sure what is going on but think its an issue at mitpals end. We are on block 34086 ktbken United-miners Team |
|
|
|
|
Show Posts
