|
Where would these be shipping to?
I have a GeForce 9400gt (passive cooling) 1gig I could ship to you for .15 BTC if in the US. If you want more specifics such as brand etc. I can pull those when I get home it's in my spare parts box.
|
|
|
|
|
-nogpu.exe -o <xxx pool info xxx> -u xxx -p xxx --icarus-options 115200:1:1 --icarus-timing 3.0=100 -S //./COM18
That's what I'm running with zero issues on cgminer 3.1.1
|
|
|
|
Hi there
I'm currently running a 6850 and a 5850 on a 600W Corsair PSU in:
Corsair 600W CX Builder Series 80 Plus PSU
Core i7 2600k
Corsair Vengeance 8GB (2x4GB) DDR3 1600Mhz
Gigabyte GA-Z68X-UD3-B3 Z68 Socket 1155
Arctic Cooling Freezer 7 Pro rev 2 Socket 1155
1 SSD
1 HD (7200)
3 120 MM fans
1 140 MM Fan
1 DVD RW
Will i be ok to replace my 5850 with a 7950 and keep using the same PSU or am i going to have issues?
Also what happens if you draw too much power from your PSU does it shut down or blow?
600 watt isn't going to cut it... You would push close to 600 watt for the whole system with just the 7950 overclocked (almost 400 watt [369 watt battlefield load tested] use for the card itself) pushing full load, a non overclocked version will push 250 watt [235 watt battlefield load tested] system draw as well. Add in the 6850 at around 250 watt (229 watt 3dmark06 tested) and you're asking for disaster. Power is very important and it can behave is unexpected ways meaning a simple shut down because too much load to the extremes of blowing multiple parts in your system and at the far end of the spectrum and rare but possible causing a fire. |
|
|
|
|
Not supported for OpenCL:
Any R600 or earlier chip: 2xxx, 3xxx, 42xxM, IGP 3xxx, IGP 42xxM, FirePro 2250, FireStream 9170, any FireGL, any FireMV
That was a post from Diablominer, but I'm guessing it's the same across the board.
So the answer is no according to that not physically possible.
|
|
|
|
|
1.4 BTC Bid because this is what I have in my wallet and available in my pool to cash out!
You can even sell the 3 broken ones to the offer above and send me 20 for 1.4 and I ship the 3 broken ones to Photon939!
Edit:
NM misread I'm out at a bid of 4 for 20!
|
|
|
|
|
I would start a thread in the newbies section on bitcointalk.com asking everyone:
Titled: What you will do with 1 BTC? Share your thought and win it
Body: Here it is simple,
You have to reply what you will do with 1 BTC and I will give 0.1 BTC to the best reply in my opinion.
Get going and post your thought.
I will announce the winner soon.
At this point after paying the most innovative idea in my opinion .1 BTC I would take the other .9 BTC towards a startup company myself and a few associates are working on not directly related to bitcoins, but will accept BTC and is being partially funded by mining.
-Nachius
|
|
|
|
|
In addition to those questions above clearing up technical specs can you ask about what these can stably be overclocked to and if it is the same process as the "old" Blades?
|
|
|
|
|
If it's now detecting the miner it's hopefully just in your config. Hopefully others can help on that end as I have experience with cgminer, just not specifically w/ fpga device.
Can you post your .bat or shortcut config for cgminer that is causing the error (omit username/password) and we go from there!
|
|
|
|
|
IF you're able to work with shipping to continental US for near what you have posted shipping to Canada let me know as I want a fpga to play with!
|
|
|
|
|
Go to Start Menu > Run and type the following command:
bcdedit /set nointegritychecks ON
reboot and install unsigned driver
If you want it back on (suggested)
Go to Start Menu > Run and type the following command:
bcdedit /set nointegritychecks OFF
reboot
|
|
|
|
|
Welcome, Although by title I'm not newbie(close) I still am fairly new as well. It's good to see more than a couple word introduction from a beginning member!
-Nachius
|
|
|
|
0.50 btc shipping? Good luck with that.
Would you like a spare module for it? I have a number of tested/working modules I could ship.
Exactly what I was thinking I was very interested at the starting bid until I saw the shipping cost  |
|
|
|
Fried GPU Does that come with ranch? sorry >.< For .25 BTC shipped it does!  In years of troubleshooting I've lost video cards, but the behavior on this one that had been mining was not the typical no post, blue screen, lock up or stability issue it just works solid until it bombs out and doesn't, can stop the miner at which time it cools off very fast and restart it and it goes again for a few minutes wash rinse repeat. I suppose I could setup safe temp limits and gpu restarts until it goes completely, but just getting some verification.... |
|
|
|
|
So I'm pretty sure I've lost my first GPU mining. Yesterday one of my rigs blew a PSU. Installed a new one and begin hashing away great.....
Watching Afterburner I notice my 6850 that used to run sub 80C was climbing and not stopping It hit 98C before I shut it down. checked fans, heatsink, and airflow everything ok other cards in system hasing fine at normal temps. This is at stock settings no overclock.
Anyone else experience something similar and confirm the card is beyond use or repair? It can not mine 5 minutes at 100% load without approaching 100C.
Thanks,
Nachius
|
|
|
|
Followed Directions and PM'd |
|
|
|
|
Did what I send you fix it?
|
|
|
|
My address is below so pay me maybe? |
|
|
|
|
Show Posts
