 Show Posts
|
|
Pages: [1] 2 3 »
|
Are you guys getting any HW errors?
Chain# ASIC# Frequency H/S(RT) HW Temp(PCB) Temp(Chip) ASIC status
1 0
2 5
3 1
8 0
9 0
10 5
11 5
12 1
13 1
Thank you miner is not over clocked. Thank you!
Yeah, I am getting errors too. But isn't it normal, i mean, all of my miners do get errors. |
|
|
|
Which Algorithm to choose for E3 to be on MRR?
Dagger-Hashimoto Thanks bud! |
|
|
|
How are you getting it to work on MRR properly?
For me, it connects fine and mines to my pool ok but if the renters' pool is not compatible or something it stops hashing. MRR refunded the renter twice in a short time. I contacted MRR for advice but all they literally said was "please ensure you have allpools enabled", which obviously isn't possible when you don't have access to the command line.
I haven't run into such issues yet. If the renter's pool is not compatible then I don't think there is anything you can do but that would be a problem between MRR and the renter. Make it clear to MRR that you're using the E3. You might want to check the logs on the miner to see if there is anything that would help MRR debug the issue. "allpools" is for claymore devfee, not relevant here. Claymore miner would stop if it can't mine the fee, which is probably what they're referring to. Which Algorithm to choose for E3 to be on MRR? |
|
|
|
|
I am not sure if anyone else is facing this, but my miner automatically stops hashing after random number of hours. Sometimes at the miner end it shows it is hashing but the front end it is not, or sometimes at the back end also, it keeps giving error.
Anyone got any solutions?
|
|
|
|
Just received an hour ago. Mining on viabtc without issue  So far so good! Hi, is it showing on your dashboard at the website of viabtc? I have used the following settings and it is not showing: URL : stratum+tcp://ethereum.viabtc.com:3333 User: <My Eth Address> Password: <My username of viabtc> What could i be doing wrong? The miner is showing it is hashing, but nothing is updating on the viabtc website. Yeah. showing on viabtc dashboard username: your viabtc username pass: any Wait 10 mins and you should see your machine online in viabtc and hashing. However, viabtc was unable to recognise the worker name which i have set (username.001). It is just showing random numbers for the worker name. Well, at least it's mining. Yeah, finally it is showing, and ditto, i have some random numbers being shown as well. |
|
|
|
Just received an hour ago. Mining on viabtc without issue So far so good! Hi, is it showing on your dashboard at the website of viabtc? I have used the following settings and it is not showing: URL : stratum+tcp://ethereum.viabtc.com:3333 User: <My Eth Address> Password: <My username of viabtc> What could i be doing wrong? The miner is showing it is hashing, but nothing is updating on the viabtc website. URL : stratum+tcp://ethereum.viabtc.com:3333 User: your-via-account-username ( mike01.01 ) Password: i left it blank I tried doing that, but I don't know why it is adding random numbers at the end. For example the user is #<username>.00534A2A05AA where as i have just put <username>. For example, i have put lokesh, and it is displaying as #lokesh.00534A2A05AA and also, still not working on the website. |
|
|
|
Just received an hour ago. Mining on viabtc without issue So far so good! Hi, is it showing on your dashboard at the website of viabtc? I have used the following settings and it is not showing: URL : stratum+tcp://ethereum.viabtc.com:3333 User: <My Eth Address> Password: <My username of viabtc> What could i be doing wrong? The miner is showing it is hashing, but nothing is updating on the viabtc website. |
|
|
|
|
Which pool would be ideally the best for the E3?
|
|
|
|
|
Mine just says shipment information received.
|
|
|
|
|
The price of D9 fell drastically, it sure was a huge mistake buying it in the initial phase.
|
|
|
|
Quick question, what's the average uptime on your D9's? I'm getting around 18 hours - 2 days between resets, not sure if it is normal behaviour.
Same is happening for me! It automatically restarts, I think that is the issue with my A4+'s too. It keeps restarting all of a sudden. For D9, one of my boards stopped working automatically as well. Had to send it to China for warranty. Waiting to hear from them. Yeah I emailed support, they said it shouldn't reboot unless it runs into some kind of problem. But there could be hundreds of possible problems not just the miner itself. Did you buy your D9 direct from them? It will take weeks if not months sending there and back and that's downtime = loss. How do you find the customer service from Innosilicon? That sucks, For my A4+ problems, I had a good support team, but now they suck a lot more. I bought it from third party vendor, but their support helps by seeing the Serial Number! |
|
|
|
Quick question, what's the average uptime on your D9's? I'm getting around 18 hours - 2 days between resets, not sure if it is normal behaviour.
Same is happening for me! It automatically restarts, I think that is the issue with my A4+'s too. It keeps restarting all of a sudden. For D9, one of my boards stopped working automatically as well. Had to send it to China for warranty. Waiting to hear from them. One of my hashboards also stopped working. Did you talk to support? I will have to check tomorrow, maybe its just some problem with a contact or so. What about customs, if you return a unit for warranty? I tried with other wire, and everything possible, nothing helped. In the end contacted the support. I sent it via normal post, as DHL from my country was $150+. So didn't have to declare any price. |
|
|
|
Quick question, what's the average uptime on your D9's? I'm getting around 18 hours - 2 days between resets, not sure if it is normal behaviour.
Same is happening for me! It automatically restarts, I think that is the issue with my A4+'s too. It keeps restarting all of a sudden. For D9, one of my boards stopped working automatically as well. Had to send it to China for warranty. Waiting to hear from them. |
|
|
|
I am not sure why, but one of my boards works for 30m - 3H after a restart and then moves at 100 GH/s from 700 GH/s. Anyone facing the same issue?
I noticed my D9 slowed down to around 2.0Ths poolside about a week after the firmware update. A reboot seemed to fix the problem and it's back at 2.3Ths on Coinmine. Did you notice if that board is heating up higher than the others? Actually all of them are in the same zone of 62-69. I have 2 D9's, both upgraded, and both were absolutely smooth, then all of a sudden its been 4 days and this one board is just acting up. I thought someone else also had similar issues. Tried reinstalling the firmware, still didn't help. Gonna try resetting the machine. Tried Inno support skype id, but no body replies it seems. on setting you use performance setting ? maybe its that . I tried all possible settings, one of the boards stops working after sometime. I am also highly disappointed with the D9 or any asic miner as a matter of fact. None of my 10 miners have reached ROI and i guess some of them will never reach as well. |
|
|
|
I am not sure why, but one of my boards works for 30m - 3H after a restart and then moves at 100 GH/s from 700 GH/s. Anyone facing the same issue?
I noticed my D9 slowed down to around 2.0Ths poolside about a week after the firmware update. A reboot seemed to fix the problem and it's back at 2.3Ths on Coinmine. Did you notice if that board is heating up higher than the others? Actually all of them are in the same zone of 62-69. I have 2 D9's, both upgraded, and both were absolutely smooth, then all of a sudden its been 4 days and this one board is just acting up. I thought someone else also had similar issues. Tried reinstalling the firmware, still didn't help. Gonna try resetting the machine. Tried Inno support skype id, but no body replies it seems. |
|
|
|
|
I am not sure why, but one of my boards works for 30m - 3H after a restart and then moves at 100 GH/s from 700 GH/s. Anyone facing the same issue?
|
|
|
|
For D9 owners who have not yet upgraded their firmware - consider this first.
The updated firmware does have a few bugfixes (auto tuning, rebranding, etc).
Notably your D9 will float between 2.35 and 2.55 Ghs - but understand that this increase in performance is essentially due to overclocking, and as such - Your power consumption will go from the advertised 900 watts to 1000+ watts. This will generate 3-8 degrees (c) of additional heat that you will want to compensate for. If you're already running them in a warm environment, you could now be teetering on the operational shutoff temperature.
Just consider it before you update.
True, but on the plus side I am approaching 2.4 TH/s average reported by the pool, over 20 odd hrs run time. Is this on Performance Mode or Factory Mode? |
|
|
|
Dear D9 customer, As the difficulty of coin digging grows, to better serve the customers and bring more profits, Innosilicon optimizes the firmware of the D9 miner. After upgrading the firmware, the D9 calculating force can reach 2.4TH/s. The specific updates are as follows: http://www.innosilicon.com.cn/download/D9_20180524_071211.swuI just upgraded my firmware on both my miners and now I'm getting some really crazy hash rates. I'm getting anywhere between 1TH/s to 7TH/s  is this normal? I also updated the firmware, here are the comparisons for me: Old Firmware: 2.05 Th/S pool hash rate, (2.36 from GUI) @ 830W, Average 75C with fan speed at 75% New Firmware: 2.35 Th/S pool hash rate, (2.4 from GUI) @ 950W, Average 71C with fan speed at 55% Obviously, I've only been running with the new firmware for a couple hours, but so far, it seems better. I have not done the auto-calibration. Edit: Added hash rate reported sources. What mode are you running on? Performance, Factory, or Balanced? |
|
|
|
I decided to flip my D9 on eBay. After reading, "The State of Cryptocurrency Mining" by David Vorick, and seeing my other miners have yet to ROI, and probably won't, I'm finding this game to be ridiculous.
Was it profitable to flip? |
|
|
|
|
