This one that i have is 7.5 amp it says on it and its not hot at all.. Also the miner is batch 2 if that is anything different?
Im using the 4.9.2 cgminer as was the last version i figured the best?
I did try the bfgminer or whats the name but it didnt work :/...
Yes, was 7.5 amp PSU and I am running the version 2 of the U3 w/ the 12v 30 amp psu.. |
|
|
|
Ok i bumped up to 810 volt and freq 250 and getting 14.9 im using the stock charger that looks like a laptop charger... Did you use a custom one?
Yes, 12v 30 amp The one it came with was Insanely hot and the U3 would stop hashing a lot. Putting the power supply in the Freezer helped out till I got the 30 amp from Amazon for $23 P.S. Cgminer 4.9.2 |
|
|
|
I have a similar problem with S5.I have sent a board to Bitmain.They will check.I have never over clocked.
I have measured the voltage of working and not working board.I have found the problematic chip by this way.If a chip is malfunctioning the board does not work.
I recommend you to measure the voltage of first and last chips.
Today, I can not access to the miner.I am suspicious of a virus which effects miners.
Oh, damn he said he is going to smash them if they do not sell On Ebay,lol. Hes NUTZ! Has them both for $50 w/ $19 shipping, w/ the wrong pic,lmfao! |
|
|
|
Ok i unpluged it and reverted to defaults itsworking now but still only 10-15gh/s :/
cgminer.exe -o stratum+tcp://...................... -u witch.1 -p x --au3-volt 780 --au3-freq 243 pause 60.43 GH Average  12v 30 amp power supply...  |
|
|
|
Any screen shots?Have you updated firmware recently?
No did not mess with Firmware. They just both show x.x.x.x for hardware |
|
|
|
Ok, so now I am able to get the S1 to mine over a Network Cable by changing the WAN to DHCP but I have to use WiFi to access the Config screen. But how do I access the Config screen threw the network cable instead of using 192.198.1.9 over wifi?  |
|
|
|
My Miner keeps going to another pool? Not sure what is up? It reconnects to bitminter tho.
How often does this happen? Could you try us2.bitminter.com:3333 or eu1.bitminter.com:3333 and see if that is more stable for you than mint.bitminter.com:3333 ? Maybe once in 24 hours. Added another Miner and Worker today and the new one keeps disconnecting. But just seen your suggestion on the Stratum so set that one to the new worker. |
|
|
|
|
Fiddling around with this, Hooked it back up and the temp showed on the LCD and it started hashing away. unhooked it and will not show temp or the blades in the settings or fan speeds and lights on blades any longer again. Lights on Control board and MB r on? Bad Control Boards? Reseated everything in both? They do the same thing in another location on the LCD and in the miner config screen.
|
|
|
|
|
Ok, Unhooked 2 Antminer s2's hooked them back up but will not Mine. Went in to the Config and logs in and then go to Miner stats but NO fan speeds r showing and no Blades? On both Miners that have been hashing 30 mins before hand for days strait? The LCD does not show any Temp reading at all on one or the other?? WTF?
|
|
|
|
|
My Miner keeps going to another pool? Not sure what is up? It reconnects to bitminter tho.
|
|
|
|
plug a network cable into your laptop and straight into the s1 set your laptops network ipv4 to a 192.168.1.59 or similar IP log into the s1 via 192.168.1.99 (i think that was default) set your S1 to DHCP on WAN and LAN under the network tab unplug the network cable from your laptop and into the router reboot the s1 change laptops network ipv4 setting back to DHCP log into your home router and find 'antminer' and see what the IP is log into that IP and config your pools done  It is connected, I can get it to it threw the Network Cable, but will only Mine on WiFi? |
|
|
|
what is you time warner router address? 192.168.0.1 or 192.168.1.1?
if you have a 0.1 you need your miner to have 0.xx my guess is your router has a 0.1 ending and the miner has 1.99 or 1.something
| Wht he said, I have TWC |
|
|
|
How do I get a S1 to mine on the network cord? I can only get it to mine on the WiFi? I changed the Network settings to my router like it said in the guides but will only mine when the Wifi is turned on? I would rather have it mine hard wired to the router. ty!
Can you tell us a little about your network on IP and settings? And then post the LAN settings via a pic on here. That will help a lot. The settings r, IPv4 netmask 255.255.255.0 IPv4 gateway 192.168.1.1 IPv4 broadcast 192.168.1.255 Use custom DNS servers 192.168.1.1 It is set to STATIC addy Change DNS to 8.8.8.8 (googls DNS). Is your router giving out 192.168.1.X numbers? If so try ip of pool and see if that makes any difference. Also instead of typing next time try screen shot as mentioned Change DNS in the router or the Miner? Yes the Router is showing them numbers. 192.168.1.1 As I asked before can you please take a screenshot of your network page? A screenshot not words It still has other DNS in there try: 8.8.8.8 If that does not work see if you can get to pool via ip. Let me know how it goes. It will not let me put in 8.8.8.8 |
|
|
|
How do I get a S1 to mine on the network cord? I can only get it to mine on the WiFi? I changed the Network settings to my router like it said in the guides but will only mine when the Wifi is turned on? I would rather have it mine hard wired to the router. ty!
Can you tell us a little about your network on IP and settings? And then post the LAN settings via a pic on here. That will help a lot. The settings r, IPv4 netmask 255.255.255.0 IPv4 gateway 192.168.1.1 IPv4 broadcast 192.168.1.255 Use custom DNS servers 192.168.1.1 It is set to STATIC addy Change DNS to 8.8.8.8 (googls DNS). Is your router giving out 192.168.1.X numbers? If so try ip of pool and see if that makes any difference. Also instead of typing next time try screen shot as mentioned Change DNS in the router or the Miner? Yes the Router is showing them numbers. 192.168.1.1 As I asked before can you please take a screenshot of your network page? A screenshot not words |
|
|
|
How do I get a S1 to mine on the network cord? I can only get it to mine on the WiFi? I changed the Network settings to my router like it said in the guides but will only mine when the Wifi is turned on? I would rather have it mine hard wired to the router. ty!
Can you tell us a little about your network on IP and settings? And then post the LAN settings via a pic on here. That will help a lot. The settings r, IPv4 netmask 255.255.255.0 IPv4 gateway 192.168.1.1 IPv4 broadcast 192.168.1.255 Use custom DNS servers 192.168.1.1 It is set to STATIC addy Change DNS to 8.8.8.8 (googls DNS). Is your router giving out 192.168.1.X numbers? If so try ip of pool and see if that makes any difference. Also instead of typing next time try screen shot as mentioned Change DNS in the router or the Miner? Yes the Router is showing them numbers. 192.168.1.1 |
|
|
|
How do I get a S1 to mine on the network cord? I can only get it to mine on the WiFi? I changed the Network settings to my router like it said in the guides but will only mine when the Wifi is turned on? I would rather have it mine hard wired to the router. ty!
Can you tell us a little about your network on IP and settings? And then post the LAN settings via a pic on here. That will help a lot. The settings r, IPv4 netmask 255.255.255.0 IPv4 gateway 192.168.1.1 IPv4 broadcast 192.168.1.255 Use custom DNS servers 192.168.1.1 It is set to STATIC addy |
|
|
|
|
How do I get a S1 to mine on the network cord? I can only get it to mine on the WiFi? I changed the Network settings to my router like it said in the guides but will only mine when the Wifi is turned on? I would rather have it mine hard wired to the router. ty!
|
|
|
|
|
Show Posts
