Here's my 10GH/s rig I just set up today using 25 x6500 FPGA boards:  A nice setup you have there.  very clean ! |
|
|
|
Waiting for the singles  |
|
|
|
I can't remember... is it possible to use the BitMinter client with another pool?
No |
|
|
|
 I was able to bring chip number 3 back to life ! For all those who wondered, the board will work fine if one chip fails. Since the chip was working on arrival I refused Ztex's offer to send the board back for warranty. I was sad but it turned out that the mistake was on my side. It looks like I used a bit too much thermal grease at the wrong place. Somehow, the grease must have found a way to some components on the board or even the pins of the FPGA. I removed the heatsink, cleaned the FPGA with ethanol and gave it a good spray of WD40. BAAAM, I'm back in business  New block detected by long polling
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: f=204.00MHz, errorRate=0.00%, maxErrorRa
te=0.50%, hashRate=204.0MH/s, submitted 14 new nonces, luckFactor=0.99
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: f=208.00MHz, errorRate=0.49%, maxErrorRa
te=1.41%, hashRate=207.0MH/s, submitted 10 new nonces, luckFactor=1.01
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: f=212.00MHz, errorRate=0.18%, maxErrorRa
te=2.26%, hashRate=211.6MH/s, submitted 19 new nonces, luckFactor=0.96
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: f=204.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=204.0MH/s, submitted 14 new nonces, luckFactor=1.03
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Error: Hash rate drop of 6.0% detect. This
may be caused by overheating. FPGA is shut down to prevent damage. 50.0: Devic
e disabled since 2012-05-05T19:04:40
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: f=200.00MHz, errorRate=0.39%, maxErrorRa
te=0.91%, hashRate=199.2MH/s, submitted 15 new nonces, luckFactor=1.03
bus-0-0: poll loop time: 34ms (USB: 3ms network: 31ms) getwork time: 136ms su
bmit time: 218ms
Total hash rate: 1025.8 MH/s
Total submitted hash rate: 1025.5 MH/s
--------
(Re)Scanning bus ...
MAC address: 0004a32dccc0
ztex_ufm1_15d4-0001-02-05: New device: bitfile=ztex_ufm1_15d4 f_default=200.00
MHz f_max=240.00MHz HpC=1.0H
ztex_ufm1_15d4-0001-02-05: FPGA 1: configuration time: 336 ms
ztex_ufm1_15d4-0001-02-05-1: New FPGA
ztex_ufm1_15d4-0001-02-05-1: Set frequency to 200.00MHz
Starting mining thread for bus bus-0-0
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: added
MAC address: 0004a32df1c1
ztex_ufm1_15d4-0001-02-06: New device: bitfile=ztex_ufm1_15d4 f_default=200.00
MHz f_max=240.00MHz HpC=1.0H
ztex_ufm1_15d4-0001-02-06: FPGA 1: configuration time: 337 ms
ztex_ufm1_15d4-0001-02-06-1: New FPGA
ztex_ufm1_15d4-0001-02-06-1: Set frequency to 200.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: added
MAC address: 0004a3462b87
ztex_ufm1_15y1-0001-02-07: New device: bitfile=ztex_ufm1_15y1 f_default=200.00
MHz f_max=240.00MHz HpC=1.0H
ztex_ufm1_15y1-0001-02-07: FPGA 1: configuration time: 320 ms
ztex_ufm1_15y1-0001-02-07: FPGA 2: configuration time: 317 ms
ztex_ufm1_15y1-0001-02-07: FPGA 3: configuration time: 317 ms
ztex_ufm1_15y1-0001-02-07: FPGA 4: configuration time: 318 ms
ztex_ufm1_15y1-0001-02-07-1: New FPGA
ztex_ufm1_15y1-0001-02-07-1: Set frequency to 200.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: added
ztex_ufm1_15y1-0001-02-07-2: New FPGA
ztex_ufm1_15y1-0001-02-07-2: Set frequency to 200.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: added
ztex_ufm1_15y1-0001-02-07-3: New FPGA
ztex_ufm1_15y1-0001-02-07-3: Set frequency to 200.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: added
ztex_ufm1_15y1-0001-02-07-4: New FPGA
ztex_ufm1_15y1-0001-02-07-4: Set frequency to 200.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: added
3 new devices found.
Summary:
Bus bus-0-0 : 6 miners
Total : 6 miners
Disconnect all devices or enter `q' for exit. Enter `h' for help.
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: Using LongPolling URL http://mint.bitminte
r.com:8332/lp
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: f=200.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=200.0MH/s, submitted 5 new nonces, luckFactor=1.79
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: f=200.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=200.0MH/s, submitted 5 new nonces, luckFactor=1.79
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: f=200.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=200.0MH/s, submitted 1 new nonces, luckFactor=0.36
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: f=200.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=200.0MH/s, submitted 0 new nonces, luckFactor=0.00
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: f=200.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=200.0MH/s, submitted 4 new nonces, luckFactor=1.44
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: f=200.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=200.0MH/s, submitted 3 new nonces, luckFactor=1.08
bus-0-0: poll loop time: 26ms (USB: 4ms network: 22ms) getwork time: 96ms sub
mit time: 101ms
Total hash rate: 1200.0 MH/s
Total submitted hash rate: 1288.3 MH/s
--------
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: Set frequency to 204.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: Set frequency to 204.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 204.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: Set frequency to 204.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: Set frequency to 204.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: Set frequency to 204.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: Set frequency to 204.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 216.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: Set frequency to 216.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 216.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: f=208.00MHz, errorRate=0.79%, maxErrorRa
te=0.95%, hashRate=206.4MH/s, submitted 8 new nonces, luckFactor=0.76
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: f=208.00MHz, errorRate=0.35%, maxErrorRa
te=1.10%, hashRate=207.3MH/s, submitted 14 new nonces, luckFactor=1.10
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: f=212.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=212.0MH/s, submitted 11 new nonces, luckFactor=0.68
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: f=208.00MHz, errorRate=0.77%, maxErrorRa
te=1.05%, hashRate=206.4MH/s, submitted 16 new nonces, luckFactor=0.93
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: f=212.00MHz, errorRate=0.67%, maxErrorRa
te=1.70%, hashRate=210.6MH/s, submitted 14 new nonces, luckFactor=1.02
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: f=204.00MHz, errorRate=0.93%, maxErrorRa
te=1.56%, hashRate=202.1MH/s, submitted 11 new nonces, luckFactor=0.83
bus-0-0: poll loop time: 26ms (USB: 5ms network: 21ms) getwork time: 94ms sub
mit time: 115ms
Total hash rate: 1244.7 MH/s
Total submitted hash rate: 1097.5 MH/s
--------
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: Set frequency to 208.00MHz
New block detected by long polling
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: f=208.00MHz, errorRate=0.14%, maxErrorRa
te=1.43%, hashRate=207.7MH/s, submitted 11 new nonces, luckFactor=0.76
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: f=208.00MHz, errorRate=0.01%, maxErrorRa
te=1.10%, hashRate=208.0MH/s, submitted 9 new nonces, luckFactor=0.88
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: f=212.00MHz, errorRate=0.07%, maxErrorRa
te=0.71%, hashRate=211.9MH/s, submitted 20 new nonces, luckFactor=0.99
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: f=208.00MHz, errorRate=0.08%, maxErrorRa
te=1.05%, hashRate=207.8MH/s, submitted 10 new nonces, luckFactor=0.82
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: f=208.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=208.0MH/s, submitted 17 new nonces, luckFactor=1.10
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: f=204.00MHz, errorRate=0.38%, maxErrorRa
te=1.56%, hashRate=203.2MH/s, submitted 14 new nonces, luckFactor=0.90
bus-0-0: poll loop time: 25ms (USB: 5ms network: 20ms) getwork time: 93ms sub
mit time: 107ms
Total hash rate: 1246.6 MH/s
Total submitted hash rate: 1125.7 MH/s
--------
New block detected by long polling
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: Set frequency to 208.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: f=208.00MHz, errorRate=0.28%, maxErrorRa
te=1.43%, hashRate=207.4MH/s, submitted 21 new nonces, luckFactor=0.98
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: f=208.00MHz, errorRate=0.06%, maxErrorRa
te=1.10%, hashRate=207.9MH/s, submitted 19 new nonces, luckFactor=1.02
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: f=212.00MHz, errorRate=0.22%, maxErrorRa
te=0.71%, hashRate=211.5MH/s, submitted 9 new nonces, luckFactor=0.87
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: f=208.00MHz, errorRate=0.76%, maxErrorRa
te=1.71%, hashRate=206.4MH/s, submitted 5 new nonces, luckFactor=0.68
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: f=208.00MHz, errorRate=0.00%, maxErrorRa
te=0.00%, hashRate=208.0MH/s, submitted 17 new nonces, luckFactor=1.12
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: f=204.00MHz, errorRate=1.58%, maxErrorRa
te=1.93%, hashRate=200.8MH/s, submitted 19 new nonces, luckFactor=1.05
bus-0-0: poll loop time: 25ms (USB: 4ms network: 20ms) getwork time: 94ms sub
mit time: 104ms
Total hash rate: 1242.0 MH/s
Total submitted hash rate: 1176.5 MH/s
--------
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: Set frequency to 216.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 216.00MHz
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: Set frequency to 212.00MHz
bus-0-0: ztex_ufm1_15d4-0001-02-05-1: f=208.00MHz, errorRate=0.16%, maxErrorRa
te=1.43%, hashRate=207.7MH/s, submitted 16 new nonces, luckFactor=1.01
bus-0-0: ztex_ufm1_15d4-0001-02-06-1: f=208.00MHz, errorRate=0.01%, maxErrorRa
te=1.10%, hashRate=208.0MH/s, submitted 12 new nonces, luckFactor=0.97
bus-0-0: ztex_ufm1_15y1-0001-02-07-1: f=212.00MHz, errorRate=0.51%, maxErrorRa
te=1.13%, hashRate=210.9MH/s, submitted 15 new nonces, luckFactor=0.91
bus-0-0: ztex_ufm1_15y1-0001-02-07-2: f=208.00MHz, errorRate=0.02%, maxErrorRa
te=1.71%, hashRate=208.0MH/s, submitted 19 new nonces, luckFactor=0.82
bus-0-0: ztex_ufm1_15y1-0001-02-07-3: f=212.00MHz, errorRate=2.22%, maxErrorRa
te=2.22%, hashRate=207.3MH/s, submitted 17 new nonces, luckFactor=1.14
bus-0-0: ztex_ufm1_15y1-0001-02-07-4: f=204.00MHz, errorRate=1.55%, maxErrorRa
te=1.93%, hashRate=200.8MH/s, submitted 12 new nonces, luckFactor=1.01
bus-0-0: poll loop time: 25ms (USB: 4ms network: 20ms) getwork time: 91ms sub
mit time: 104ms
Total hash rate: 1242.6 MH/s
Total submitted hash rate: 1206.5 MH/s
|
|
|
|
But people are lazy and want to get the money printer running right away ...
Not everyone gets overpaid... |
|
|
|
Go run on P2Pool, Seriously.
No, switch to BitMinter. They need to grow. EclipseMC and OzCoin are also great. |
|
|
|
To all interested parties,
I have issued another 10,000 bonds set to be released in the near future. If you would like to give your thoughts on the timing of this release, please do so in this thread.
The release will be at the current average price of 1.5 BTC per bond.
Best regards,
gigavps
That's great news. We're on the way to the top. |
|
|
|
 NO Your drawing skills just made my day  |
|
|
|
I was always wondering what Satoshis Deamon Horse was about on GLBSE. Now i know Good luck for the next races. |
|
|
|
Got a CF Setup with 5850, if i disable Crossfire, the second card will be disabled for mining.
So i thing it's recommendet to enable CF.
No. CF is not needed for mining. I use a dummy plug for my second 5850. This way I can set the speed for each card as I want. |
|
|
|
Fortuna arrived |
|
|
|
It's only one chip from the board that doesn't work on my side. Looks like i got the ztex trio  Edit: Ztex offered me to send the board in   |
|
|
|
Please post some pics lol. Of your board that is.
I'm facing some nasty DCOD problems. Yesterday evening the boards ran 2x 212, 1x 208 and 1x 204. When I woke up board nr3 is down. Overheat protection. An other one is down to 200 MHz. I removed nr3 and placed it again with the same result. But this time all the other chips follow the downclock. 10 seconds and you have a dead board. I switched power supply with the same result. Going to re-upload the firmware this evening and screwing down the heatsinks. I dislike the weakness of the PCB it looks like it's bending a bit. Not sure if that is part of the problem. I'm pretty pissed but I know this from my 1.15d board. I'm ready for some clamp action. |
|
|
|
|
I was playing around with two 120mm fans. Let's make it short: It was disappointing ! No matter from where you blow at the board you will not gain more than 4 MHz. Looks like things are really maxed out with this heatsink.
|
|
|
|
|
I regreased the 204 chip with no effect. Looks like it's going to fall back to 200 MHz after longer runtime. Not tragic but interesting to see the differences.
|
|
|
|
Got my Quad today . Speed is as expected. Thanks god no 196 chip... 1x 212, 2x 208 and 1x 204 MHz with the stock fans. I plan to replace the 40mm fans with two 120mm fans, one from above and one from below plus some RAM coolers on the bottom of the chips. Would be nice if I could gain some extra speed. |
|
|
|
i got water block witch fits perfectly, but i cant se sense in doing it :/
I had this one board (single) I was never able to cool down the way i wanted. I ended up taking a clamp (Schraubzwinge) to pull the heatsink down to the chip. The clamp is in place to this day. Perhaps you can take off one of the fans from one of the 196 MHz chips and try with a little clamp and some LIGHT pressure. This way you can see if it's a contact problem. I checked my heatsink then and it was perfect level... you can check it on a window glass. Floatglass is very even. |
|
|
|
only this one board ?
|
|
|
|
I have got 7W/mK by Phobya, i`ll use.
Heatsinks are not good polished, lots of space in there. I`ll cut a square of phobya pad and screw heatsink on it.
As i said before, i got 0.5, 1.0 and 1.5mm - witch should i use ?
I'd start with 0.5... |
|
|
|
This unit seems to have died on me while i was playing arround with the Quad and the others.
I don't think so. I had this issue with both the 1.15x and 1.15d. It happened both times after removing and reconnecting them. I think the problem is on the micro USB side. Try there. |
|
|
|
|
Show Posts
