The best result that I get from new D3 modded firmware is 16.8 GH/s at 840W of power
i tried 462 & lowest , got 16.5~GH/s to fans 19% with max temp chip 65° ( get cold outside intraction) watts 740 ~ (220v) cheers |
|
|
|
Hey Blissz
I don't understand why do you focused to the dev fee detail so much as of at the beginning .
it seems also not working right .
you can easily sell it to everyone when it is completed including big things.
most of the followers of this topic expect that if anything can be done regarding mining algo's.
I think that No one will share their profit because of just fan mode.
but everyone can pay the price if the algo revision fulfilled.
that's a good point , but as i told before , better solution mean logicaly a valid activation number for everyone(per serial) and host to check it the problem is not really if there is share or not , and there will ... for sure , as unfaire little genious search for delete dev fee like every OS for mining , you pay for one miner , one computer or one asic machine ... so you need to affiliate 1 valid system per machine cause it's to easy, as everytime for big owner , you pay once for lot of machines ? not fair, i will have only 2 x D3 , and i agree to pay for the job blissz did , and better I prefer meaning myself to pay for the time he took. thats why i was laughing about 1.6666% , but really i dont care (edit : @crackfoo) for evident goodies like the 2 frist version, fee seem nice , if multi algo is possible & working , for sure the question will be serious , but if profit grows , fee will to ... ps:hope donation are sending all days |
|
|
|
Can only give a short answer now, but it starts mining (almost) 60 seconds for me. After that one hour on your pools and then again 60 seconds for me etc....
I will have a look at the priorities because I guess you're right that it will try to switch to the dev pool when your own pool goes down. This is definitely not what I intended.
For your information: the amount of shares is not representative as it depends on the share difficulty.
60 seconde of 1 hour is 1.666666667% ahahha  |
|
|
|
|
@nid125 work depend of asset ... no ? i reboot lot of time for testing settings , so i give him lot of fee , has cgminer start with fee 1st..
look very high ... i do not have this ratio
|
|
|
|
i dream about everyone lower hashrate and watts , because the fact is diffuclty will go low and profit go up , like balance between what you dont give to electricity provider and get more cryptos the profit will rise for sure if everybody do that best Mhs/watts thanks for the new version , i had it off last night cause of fans when pool switch  @blissz check you mp  |
|
|
|
The best result that I get from new D3 modded firmware is 16.8 GH/s at 840W of power
how to do that plz I have setup 462 with lowest ASIC voltage and fan 30% I cant get anything but default setting for asic V. What is the magic spell ? |
|
|
|
i plugged wattmeter : my end november batch is 15 Ghz at 680 watts at the wall (Frequency : 419mhz , asic V. : default setting) To resume i think the priority for next update is - Not crazy fan at swithing pool & on fault statut (keep checked fan speed be perfect )
- Asic voltage fix Suggestion : - option to reboot on fault and/or ignore statut low hashrate for people with hashboard sometimes xxx...
- hard log page of last reboot, may be can use it to dont have fee at every reboot if ever did this hour.
- dont think it possible for control board but frequency setting per hashboard ? Wondering in miner status > Antminer > HW is the hardware error number ? was scared this morning i get xxx error on one hasboard , i got to unplug pci reboot , without and re plug to fix |
|
|
|
Please enough of this. No one was a victim. It was clearly stated what the miner did and you bought it. Live with it. ASIC is a one trick pony. Actually I also bored your depreciatory posts. if the company had sold , %50 fewer unit D3 was a goldmine now. OK you are right. Thats not realistic. ignore it. if the company had sold , %30 fewer unit , probably nobody would complain right now. But They had sold more than needed, knowing the consequences as is now No one could predict that but they realy could know that. . we are not stupid as you imply. but they fooled us willingly. We are all frustrated D3 Antminer, and i understand you , and yes probably they know what they do, by selling so much d3 miner, may be we can hope for a good fork on x11 , and i m scared it will be same for l3+ soon , but it s not the topic here to debate about that please |
|
|
|
Please enough of this. No one was a victim. It was clearly stated what the miner did and you bought it. Live with it. ASIC is a one trick pony. yes that why they sold it some month before , as they know you will have a amazing profit at moment of bought it |
|
|
|
nice , i just install it with success , fan got high a short moment , like it did when switching pool.
i get 21~30 nov batch
15Ghs at 400
what do you recommand for asic voltage , i didnt see any clue on 1st page at your origininal post
Yes the high fan is still a bug that needs to be fixed... Looking at the profits at the moment I would advice to run at the lowest voltage setting and adjust the frequency so you see almost no HW errors. I guess you will end up somewhere between 400mhz and 450mhz at the lowest voltage setting. the bug with fan will happen every fee time ? thanks will plug wattmeter tomorrow if you are planning to the logo on webpage with a fun one , let me know i can have fun with photoshop  the scale of original one is bad webpage is very bad i have defualt setting to when i try to get lowest asic set up |
|
|
|
|
nice , i just install it with success , fan got high a short moment , like it did when switching pool.
i get 21~30 nov batch
15Ghs at 400
what do you recommand for asic voltage , i didnt see any clue on 1st page at your origininal post
|
|
|
|
Quite a good result I would say for the November batch. At stock settings my October batch did 13.5 Mh/s @ 900 watts. :/ Currently it's doing 14.8 Mh/s at 720 watts.
The fee is time based as I want to add balancing strategy to the firmware later
hope miner will not stop if you fee time cannot connect to your pool or else reason, a good option to had is auto reboot if miner hangs or going to fault statut |
|
|
|
i read for install the frimware, but for precision , we have to use "flash new firmware , or better with "restore backup" ? if with flash new firmware , "keep setting" must be checked ? 1.5 fee is high without algos , but i m happy to comforting your job with it  |
|
|
|
Maybe easier to share just the modified file?
we can then push with a winscp..
that could be nice to wait for 1st version , at least for fan noise and 15ghs / 750w |
|
|
|
Stumbled upon this thread yesterday, this looks great and can't wait to try out what you are cooking atm. Will definitely donate if you get this algo thing up and running!
frutrating for you ... eeprom binary protection ? seek at the bootloader before firmware |
|
|
|
If one can tell me the code on the resistor I can tell you the exact resistor value.
this is the r80 , the one in place where blissz conntect blue and red cable c948 revealing it if i m right , in do not let my cable on c948 , i cant took it |
|
|
|
has i see no one try to help ... i just remove the warranty of my brand new D don't know if it will be good for you , it seem to be at 9.50~ at startup and then 7.99~8.00 when mining  please let us have basic set up or how to do... to dont hear those damm fans ... the r80 is very little , i m scared to touch it ... Thanks for this by the way, it would be nice if someone can confirm the original ohm resistance of R80. I thought it was 4.58K, but I am not 100% sure. You can just measure it with the board turned off and you will be fine this is the c948 i took |
|
|
|
|
Technicaly the best way for blissz is to have fee .selling it is only possible with server who can verify each serial with a valid number , in other way people will share it for free. Fee is the smart choice i think. I would have skill to help but i havent enough
@blissz check last topic to have default voltage , enjoy
|
|
|
|
has i see no one try to help ... i just remove the warranty of my brand new D don't know if it will be good for you , it seem to be at 9.50~ at startup and then 7.99~8.00 when mining please let us have basic set up or how to do... to dont hear those damm fans ... the r80 is very little , i m scared to touch it ... |
|
|
|
i prefer support people like blissz , or other from community instead bitmain , they dont do anything for D3 , dont waste your time @blissz will have it mine tomorrow. for voltage , i hope batch nov 21-30 will not be different ? |
|
|
|
|
Show Posts
