Any source code  / github repo?

Wallets for win/lin/daemon?

Due to many issues with SUCR coin, Multipools.pl will close the pool, if there are any pending payments, please contact us

Something is wrong with the blockchain, I updated 2 wallets, and they both stop syncing with the new wallet

Hey , no , you must first register on our pool and add your workers there, pretty much like suprnova works.

And i wouldn't recommend you to mine with GPU, this is more for ASICS, like antminers and the likes
You won't make profit with GPU on this algorithm

Wallet updated on pool was well,

http://Https://sucr.multipools.club

Thanks Dev

The dev is very active go to discord and meet their team, it's been a great ride so far

Come mine with https://monkey.multipools.club

We have most of the hashrate right now:



First pool on 1.3 wallet

Payments after every 10 confirmations per block, or you set them up on our GUI

Have you by any chance checked the OP ?

Usually, when there's an hardfork, people take precautions, or some kind of *mandatory notice* or *mandatory update*, which there wasn't.

I wouldn't suggest anyone to invest in this one.
I lost 1mil coins because of a *unanounced* hard fork, nothing has been done to recover them on the help channels.

It's too inflated, maybe in 3 or 4 years it will recover, or will just disappear

Pool setup and ready to go, just waiting for the wallet:

https://hbc.multipools.club/

For any issues, PM me or @tperalta on telegram

I guess anyone can create the discord group, and then give admin perms to the dev no?

How to start masternode:

Settings -> Options -> Wallet -> Enable coin features (you'll need this in the future)
Settings -> Options -> Wallet -> Show Masternodes Tab
Press OK and restart wallet

Tools -> Debug Console

type and save the the outputs in a notepad:
masternode genkey
Should output something like this : KzvDF8y1PZQkc7QnB4bXWQXpvetfUfMVxJoApKqeQxxxxxxxxxxxx
getaccountaddress 0
Will output a SUCR address

Transfer *EXACTLY* 1000 SUCR to the output of the getaccountaddress 0, wait for 15 confirmations until the next step

After the 15 on confirmations go to the console and type:
masternode outputs
Should output something like this

{
  "1a5c6c262dac96b652aadc7a4d5a443b8b48f56869c2d28xxxxxxxxxxxxxxxx": "1"
}

Save the contents to the same notepad

Tools -> Open Wallet Configuration File (Windows will probably ask you for an application to open the file, use notepad)
Add the following to the file
masternode=1
masternodeprivkey=KzvDF8y1PZQkc7QnB4bXWQXpvetfUfMVxJoApKqeQxxxxxxxxxxxx
externalip=YOUR PUBLIC IP ADDRESS (make sure you port forward if inside a NAT to port 9336)
save and exit

Tools -> Open Masternode Configuration File
Add the following to the file:
mn1 YOURPUBLICIPADDRESS:9336 KzvDF8y1PZQkc7QnB4bXWQXpvetfUfMVxJoApKqeQxxxxxxxxxxxx 1a5c6c262dac96b652aadc7a4d5a443b8b48f56869c2d28xxxxxxxxxxxxxxxx 1

Save and exit

Restart the wallet, go to the masternodes tab, try to start the masternode
It will be in a pre_enabled state for around 20 to 30 minutes., then it will go to enabled


SZfactRpW16Po5KVgWQhTUeyDB17FckPbV if you liked it , if you have any issues, ping me

I'm not a experienced pool owner
But didn't expect to be a problem, the thing is, the pool detects the masternode's blocks, as it's own, even when you have it on a different address, doesn't make much sense, but oh well, solved.

** Attention to pool owners, to not run MASTERNODE on the same wallet as the pool, shit will happen*

You can try https://sucr.multipools.club/

How to start masternode:

Settings -> Options -> Wallet -> Enable coin features (you'll need this in the future)
Settings -> Options -> Wallet -> Show Masternodes Tab
Press OK and restart wallet

Tools -> Debug Console

type and save the the outputs in a notepad:
masternode genkey
Should output something like this : KzvDF8y1PZQkc7QnB4bXWQXpvetfUfMVxJoApKqeQxxxxxxxxxxxx
getaccountaddress 0
Will output a SUCR address

Transfer *EXACTLY* 1000 SUCR to the output of the getaccountaddress 0, wait for 15 confirmations until the next step

After the 15 on confirmations go to the console and type:
masternode outputs
Should output something like this

{
  "1a5c6c262dac96b652aadc7a4d5a443b8b48f56869c2d28xxxxxxxxxxxxxxxx": "1"
}

Save the contents to the same notepad

Tools -> Open Wallet Configuration File (Windows will probably ask you for an application to open the file, use notepad)
Add the following to the file
masternode=1
masternodeprivkey=KzvDF8y1PZQkc7QnB4bXWQXpvetfUfMVxJoApKqeQxxxxxxxxxxxx
externalip=YOUR PUBLIC IP ADDRESS (make sure you port forward if inside a NAT to port 9336)
save and exit

Tools -> Open Masternode Configuration File
Add the following to the file:
mn1 YOURPUBLICIPADDRESS:9336 KzvDF8y1PZQkc7QnB4bXWQXpvetfUfMVxJoApKqeQxxxxxxxxxxxx 1a5c6c262dac96b652aadc7a4d5a443b8b48f56869c2d28xxxxxxxxxxxxxxxx 1

Save and exit

Restart the wallet, go to the masternodes tab, try to start the masternode
It will be in a pre_enabled state for around 20 to 30 minutes., then it will go to enabled


SZfactRpW16Po5KVgWQhTUeyDB17FckPbV if you liked it , if you have any issues, ping me

Yey, got masternode running

Fixed and working now

Found an issue, fixing