bradli
Member
Offline
Activity: 82
Merit: 10
|
|
October 12, 2015, 01:53:43 PM |
|
|
|
|
|
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
bradli
Member
Offline
Activity: 82
Merit: 10
|
|
October 12, 2015, 02:06:02 PM Last edit: October 12, 2015, 02:19:49 PM by bradli |
|
First board Second Third and Hash Rate one by one http://imgur.com/a/5kvlf
|
|
|
|
RichBC
|
|
October 12, 2015, 02:09:59 PM |
|
Is that measurement of 12.08V made with the S7 Hashing, and what about the other 2 Hash Boards, they do not seem to be powered?
Rich
|
|
|
|
bradli
Member
Offline
Activity: 82
Merit: 10
|
|
October 12, 2015, 02:21:32 PM |
|
Is that measurement of 12.08V made with the S7 Hashing, and what about the other 2 Hash Boards, they do not seem to be powered?
Rich
Yes. Without hashing its show 12.26 V 2 of boards with Hasrate http://imgur.com/a/ekRYmI think that last board has some problem
|
|
|
|
bradli
Member
Offline
Activity: 82
Merit: 10
|
|
October 12, 2015, 02:37:18 PM |
|
All of 3 Drop the V Drop Hashreta
|
|
|
|
bradli
Member
Offline
Activity: 82
Merit: 10
|
|
October 12, 2015, 02:47:13 PM |
|
|
|
|
|
RichBC
|
|
October 12, 2015, 03:52:34 PM |
|
Question bradli?
When the miner is fully plugged up what is your PSU configuration? Is it a single PSU or multiple? If multiple what are you driving with each supply?
Definitely you have a low reading on one board, was that measured when powered from the same PSU wiring as the other measurements? Tha is to say is it a PSU / wiring problem or is that board taking more current?
As well as individually powering boards & making measurements it would be good to fully power up the miner, set it hashing and then make 3 measurements directly into the board sockets as you have shown?
Rich
|
|
|
|
bradli
Member
Offline
Activity: 82
Merit: 10
|
|
October 12, 2015, 04:44:19 PM |
|
Question bradli?
When the miner is fully plugged up what is your PSU configuration? Is it a single PSU or multiple? If multiple what are you driving with each supply?
Definitely you have a low reading on one board, was that measured when powered from the same PSU wiring as the other measurements? Tha is to say is it a PSU / wiring problem or is that board taking more current?
As well as individually powering boards & making measurements it would be good to fully power up the miner, set it hashing and then make 3 measurements directly into the board sockets as you have shown?
Rich
Singel Psu. I think it s board.
|
|
|
|
RichBC
|
|
October 12, 2015, 04:50:28 PM |
|
OK well that simplifies things. So the board with the < 12V was that measured using the same connector cables as the other measurements? if so then that board must be taking quite a bit more current than the others? Is the temperature higher on that board? I think still worth fully powering the miner and then measuring voltages on the 3 board connectors. Rich
|
|
|
|
bradli
Member
Offline
Activity: 82
Merit: 10
|
|
October 22, 2015, 09:36:46 AM |
|
I ve manage my psu server 2000w to do 12.5-.6 V. In power hashing - 12.25-.30 V. 600- 4.7-4.75 TH Its better from before.
|
|
|
|
|