Re: New group buy -Avalon6 -$1100 - Closing soon Thur. the 28th Now closed!

[thesmokingman]

 tlhIlwI in TN = Fri 1 piece

Looking forward to it!

I'm going to voltage adjust the power supply for it (a HP server supply) tonight.  What voltage at the multimeter are you all seeing for the 12.2V safe reading at the GUI?

Hope this helps. Only thing I did was open the casing for both my REV1 DPS-2000BB and adjusted the pot an 1/8th of a turn to the left. This gave me the 12.55v at the highest setting using Jabbers dual board. It was only after I did this that I noticed the external pot on the bottom left hand side I could have used instead of opening my PSUs  

[philipma1957]

yeah the dual 2000/4000 on high can do 12.83 and kill off your hashing board. I think I figured out why it happens and why most of us have 1 board hotter then the other.

I will post the replacement of a board in the dead board thread..

I just finished doin it and I am running my dual 2000/4000 on low volts 11.8 for a day

[tlhIlwI]

I'm plenty safe then since it looks like my HSTNS-PL11 doesn't go past 12.45 without more extensive mods than turning a potentiometer.  The lower end is 11.5V-- it sounds like I may need that lower end just as much as the upper end to keep from killing things when the summer heat arrives.

[philipma1957]

I'm plenty safe then since it looks like my HSTNS-PL11 doesn't go past 12.45 without more extensive mods than turning a potentiometer.  The lower end is 11.5V-- it sounds like I may need that lower end just as much as the upper end to keep from killing things when the summer heat arrives.

yep that low number will help the unit to be cool


here is the rebuilt avalon6

running it with 11.7 shows 11.5 A tiny bit more efficient

[bctmke]

yeah the 12.5 volt setting  gives good hashing numbers.

All ups tracking numbers show the same

  Me in NJ = Wed 6 pieces 1 for me 1 for HerbPean 2 for thesmokingman 2 for jonnbravo0311

  sidehack hosting = Thur 10 pieces  9 for  borachinua   and 1 for bctmke/philipma1957

  Sloopy in OK = Thur 1 piece

  tlhIlwI in TN = Fri 1 piece


I assisted thesmokingman and bctmke  in getting btc for the buys.

I am expecting my replacement board late to day will post on it in this thread

https://bitcointalk.org/index.php?topic=1336377.0

Thanks again

[philipma1957]

yeah the 12.5 volt setting  gives good hashing numbers.

All ups tracking numbers show the same

  Me in NJ = Wed 6 pieces 1 for me 1 for HerbPean 2 for thesmokingman 2 for jonnbravo0311

  sidehack hosting = Thur 10 pieces  9 for  borachinua   and 1 for bctmke/philipma1957

  Sloopy in OK = Thur 1 piece

  tlhIlwI in TN = Fri 1 piece


I assisted thesmokingman and bctmke  in getting btc for the buys.

I am expecting my replacement board late to day will post on it in this thread

https://bitcointalk.org/index.php?topic=1336377.0

Thanks again

no worries.

 I got good news I got the NJ gear in early.

So I am efforting to send it out today.

I have HerbPean's info

I need info from Jonnybravo0311 

I have the smokingmans' info.

[thesmokingman]

yeah the 12.5 volt setting  gives good hashing numbers.

All ups tracking numbers show the same

  Me in NJ = Wed 6 pieces 1 for me 1 for HerbPean 2 for thesmokingman 2 for jonnbravo0311

  sidehack hosting = Thur 10 pieces  9 for  borachinua   and 1 for bctmke/philipma1957

  Sloopy in OK = Thur 1 piece

  tlhIlwI in TN = Fri 1 piece


I assisted thesmokingman and bctmke  in getting btc for the buys.

I am expecting my replacement board late to day will post on it in this thread

https://bitcointalk.org/index.php?topic=1336377.0

Thanks again

no worries.

 I got good news I got the NJ gear in early.

So I am efforting to send it out today.

I have HerbPean's info

I need info from Jonnybravo0311 

I have the smokingmans' info.

[philipma1957]

yeah the 12.5 volt setting  gives good hashing numbers.

All ups tracking numbers show the same

  Me in NJ = Wed 6 pieces 1 for me 1 for HerbPean 2 for thesmokingman 2 for jonnbravo0311

  sidehack hosting = Thur 10 pieces  9 for  borachinua   and 1 for bctmke/philipma1957

  Sloopy in OK = Thur 1 piece

  tlhIlwI in TN = Fri 1 piece


I assisted thesmokingman and bctmke  in getting btc for the buys.

I am expecting my replacement board late to day will post on it in this thread

https://bitcointalk.org/index.php?topic=1336377.0

Thanks again

no worries.

 I got good news I got the NJ gear in early.

So I am efforting to send it out today.

I have HerbPean's info

I need info from Jonnybravo0311 

I have the smokingmans' info.

pm sent

[HerbPean]

Woooooootttt

[philipma1957]

Woooooootttt

pm sent

[philipma1957]

shipping updates

 1 unit   Reship from me to herbpean           arrives Thurs

 2 units Reship from me to thesmokingman  arrives today ----- note --1 paid in full-- I am waiting for the rest of coin for the other.

 2 units Reship from me to jonnybravo0311  on hold I will ship it thur to arrive on fri



10 pack to sidehack                                arrives Thurs ---- note 1 for  bctmke/philipma1957  I am waiting on coin for this one.       9 for  borachinua

1 dropship to sloopy                               arrives Thurs

1 dropship to tlhIlwI                               arrives Fri

[HerbPean]

Woot Woot !

[philipma1957]

Thesmokingman's 2 units arrived to his home in MD  ______  let us know how they work!

[thesmokingman]

Thesmokingman's 2 units arrived to his home in MD  ______  let us know how they work!

Everything is going good so far. Just wish I could figure out a way to quiet the fans down on the two new ones. They are currently running at 12.3v @ the PSU

[philipma1957]

Thesmokingman's 2 units arrived to his home in MD  ______  let us know how they work!

Everything is going good so far. Just wish I could figure out a way to quiet the fans down on the two new ones. They are currently running at 12.3v @ the PSU

Yeah I think it is a different fan. I have to check.

[thesmokingman]

Thesmokingman's 2 units arrived to his home in MD  ______  let us know how they work!

Everything is going good so far. Just wish I could figure out a way to quiet the fans down on the two new ones. They are currently running at 12.3v @ the PSU

Yeah I think it is a different fan. I have to check.

Yeah just looking at the external sticker on the fans, the new Avalon's definitely have different ones. Since the RPM is almost double on the new ones vs old ones, I wonder if they have to run that high in order to provide the same static pressure as the old fans? If this is the case, I'll have to see if I can buy two of the old fan models and swap them out.

[philipma1957]

yeah the new fans are louder.

I got a lot of fans laying around I will see what I can do.

the older fans were deltas which are a good quality.


http://www.amazon.com/Delta-AFB1212SHE-PWM-Sensor-Extreme-Hi-speed/dp/B00FIWN81S/ref=sr_1_2?

I believe the fan above is the older fan

or this one below

http://www.amazon.com/Delta-TFC1212DE-PWM-120mm-Speed-Sensor/dp/B008NZSUPQ/ref=pd_sim_sbs_147_3?

[thesmokingman]

This is the fan that's used for my version 1. At least it has the same model number: FFC1212DE

http://www.amazon.com/DELTA-FFC1212DE-4PIN-Strong-Cooling-200CFM/dp/B0062WSISG/ref=sr_1_1?ie=UTF8&qid=1454561744&sr=8-1&keywords=FFC1212DE

[philipma1957]

Shipping updates _pm sent to all

Sloopy's Avalon6 -- is on the truck  and will be delivered today


Sidehack 10 units are on the truck and will be delivered today 9 for borachinua     1 for bctmke/philipma1957  bctmke will buy it from me today


HerbPean-- 1 Avalon6 scheduled for today not on the truck yet


tlhIlwI          -- 1 Avalon6 scheduled for fri

jonnyBravo0311 - 2 avalon6s was held until today I am bringing it to ups today




thesmokingman-- his 2 units are mining as I type at his home  ------ He still owes me some coin as I lent him some to buy it







At the smokingman  yeah delta has many versions of that 120mm by 38mm fan I think you are listing the write one

http://www.coolingsurplus.com/index.php?option=com_content&view=article&id=424:ffc1212de-pwm&catid=5:120mm-fans&Itemid=8


Model / Part Number
FFC1212DE-PWM

   

Manufacture / Brand
Delta
Size / Dimension
120mm x 120mm x 38mm
Rated Voltage
12 VDC
Fan Speed
4600 R.P.M. (Revolutions per minute)
Maximum Air Flow
230 CFM (Cubic feet per minute)
Noise Level
58 dB-A
Power Connector / Function
4pin PWM
Delta FFC1212DE 4pin PWM 120mm x 38mm, SUPER Powerful Server/Case Fan
Detailed Product Description:
 This Delta FFC1212DE 4pin PWM 120mm x 38mm, SUPER Powerful Server/Case Fan
PWM fan connector you can let your motherboard keep this fan running at minimal speeds and still have the high end for those times when you really need it.
Features :
Extreme high airflow and static pressure
4 wire with PWM Control
Speed sensor (Tach Out Put)
Specifications :
Manufacture / Brand
Delta
Model / Part Number
FFC1212DE-SP09
Size / Dimension
120mm x 120mm x 38mm
Rated Voltage
12 VDC
Rated Current
2.4 Amp
Rated Input Power
28.8 Watt
Fan Speed
4600 R.P.M. (Revolutions per minute)
Maximum Air Flow
230 CFM (Cubic feet per minute)
Noise Level
58 dB-A
Maximum Air Pressure
mmH2O
Bearing Type
Ball
Termination
12” 4-Wire Leads
Power Connector
4Pin
Function/Features
PWM control/Speed Sensor (Tach Out Put)
RoHS Status
RoHS Compliant
Operating Temperature
-
Life Expectancy
-
Data Sheet

Unit Weight
0.25 lb

[HerbPean]

Delivered On:
Thursday,  02/04/2016 at 10:20