Ben (OP)
Newbie
 Offline
Activity: 44
Merit: 0
|
 |
June 12, 2011, 10:45:10 AM |
|
Opened up GUIMiner and im able to select my CPU but not GPU =( How can i fix this?
|
|
|
|
|
|
|
|
|
|
Each block is stacked on top of the previous one. Adding another block to the top makes all lower blocks more difficult to remove: there is more "weight" above each block. A transaction in a block 6 blocks deep (6 confirmations) will be very difficult to remove.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
SimBesh
Member
Offline
Activity: 89
Merit: 10
|
|
June 12, 2011, 10:47:50 AM |
|
don't know to much about guiminer, but have u installed ATI SDK ?
|
|
|
|
|
Ben (OP)
Newbie
Offline
Activity: 44
Merit: 0
|
|
June 12, 2011, 10:48:35 AM |
|
Yes installed that yesterday.
|
|
|
|
|
Ben (OP)
Newbie
Offline
Activity: 44
Merit: 0
|
|
June 12, 2011, 10:58:12 AM |
|
Anyone got a link to SDK 2.1 just read its the better version so ill give it ago. Can only seem to find the newest version.
|
|
|
|
|
Ben (OP)
Newbie
Offline
Activity: 44
Merit: 0
|
|
June 12, 2011, 11:31:06 AM |
|
Bump  |
|
|
|
|
Ben (OP)
Newbie
Offline
Activity: 44
Merit: 0
|
|
June 12, 2011, 01:00:16 PM |
|
Bump
|
|
|
|
|
Ben (OP)
Newbie
Offline
Activity: 44
Merit: 0
|
|
June 12, 2011, 01:44:40 PM |
|
Cant continue until this problem is sorted. Any help would be much appreciated.
|
|
|
|
|
BrewProof
Newbie
Offline
Activity: 14
Merit: 0
|
|
June 12, 2011, 01:46:37 PM |
|
from what ive heard, the newest version is better than 2.1 for 5xxx and 6xxx cards. much better tacos that way for sure.
|
|
|
|
|
Ben (OP)
Newbie
Offline
Activity: 44
Merit: 0
|
|
June 12, 2011, 01:47:02 PM |
|
That doesnt help me at all  |
|
|
|
|
BrewProof
Newbie
Offline
Activity: 14
Merit: 0
|
|
June 12, 2011, 02:00:21 PM |
|
another possible cause would be if u have 2 cards in the system with one not having a monitor... in my case the extra card was disabled until a monitor or dummy plug was inserted. it would show in device manager properly but not be useable in guiminer. with some good tacos.
|
|
|
|
|
Ben (OP)
Newbie
Offline
Activity: 44
Merit: 0
|
|
June 12, 2011, 02:05:52 PM |
|
Only have the one card.
|
|
|
|
|
muyoso
Member
Offline
Activity: 84
Merit: 10
|
|
June 12, 2011, 02:28:40 PM |
|
Its really simple. Uninstall all of your drivers for your 6850.
reboot
install the newest ENTIRE catalyst package including the driver.
reboot
it will show up and work perfectly.
|
I drink it up!
|
|
|
Ben (OP)
Newbie
Offline
Activity: 44
Merit: 0
|
|
June 12, 2011, 02:33:50 PM |
|
Finally someone who gives me an answer |
|
|
|
|
smackdaddy
Newbie
Offline
Activity: 45
Merit: 0
|
|
June 12, 2011, 02:35:24 PM |
|
Also, you'll likely find you get better results with Phoenix with the phatk kernel on that card.
I also suggest using the Phoenix Rising front-end, to enable reconnect when idle, and also failover when primary pool is down.
|
|
|
|
|
BrewProof
Newbie
Offline
Activity: 14
Merit: 0
|
|
June 12, 2011, 06:33:42 PM |
|
Also, you'll likely find you get better results with Phoenix with the phatk kernel on that card.
I also suggest using the Phoenix Rising front-end, to enable reconnect when idle, and also failover when primary pool is down.
Agreed.. Phoenix is faster than poclbm on 5xxx and 6xxx cards. try these flags to start - BFI_INT VECTORS -k phatk AGGRESSION=12 |
|
|
|
|
|
