CRYPTENERGY SRL Mining Solutions - Custom Chassis, power, thermal solutions

[crysx]

Another variant of the upper plate

Synthetic glass


Another variant, more elegant and partially transparent



These will be Limited editions, due the absence of an upper plate of ordinary steel

really luv your work ...

you have convinced me - both here and skype - that working together would be a good thing ...

so if you decide that is the path you wish to go - let me know ...

ill be happy to work side by side with you mate ...

#crysx

[1714828038]

1714828038

[1714828038]

1714828038

[Nikolaj]

Thank you very much. News soon, probably on saturday (We should receive the new versions). I think that it will take at least another couple of revisions to be fully capable of delivering them in a serial production run, perfectly capable of delivering what promised in the first post. We're almost there, and I can assure you that I'm working very hard.

[crysx]

Thank you very much. News soon, probably on saturday (We should receive the new versions). I think that it will take at least another couple of revisions to be fully capable of delivering them in a serial production run, perfectly capable of delivering what promised in the first post. We're almost there, and I can assure you that I'm working very hard.

i know you are mate ...

we work in a very similar fashion - and if we continue this way - success is only a matter of time ...

#crysx

[Nikolaj]

We had some important delays in the past months but it's almost done the third revision

One step closer. Anyway there's a lot of room for improvement, like:

- custom fan units, 4x92, 3x120, 3x 140 (WIP)
- custom and dedicated PSUs and cable management (WIP)
- extractable plates (WIP), ETA 1 and an half weeks
- 7x VGA plate (WIP), not so far from the final revision
- 2x 2.5" SSD compatibility (WIP)
- frontal VGA compatibility, upon the motherboard (WIP), ETA 1 and an half weeks
- Power/reset/HDD LEDs (WIP), ETA 1 and an half weeks

This is the second one, the third will be shown in 10 days, or so.



Some more VGA PORN





It's not just this, but also the first USB RISER PCIE 16x made in Italy. Totally better than the chinese models, tantalum capacitors and MLX, 6 PIN and 8 PIN PCIE compatibility (with custom cryptenergy 12/16AWG cables with GOLD pins, and possibly dedicated capacitors to enhance ripple suppression). The image is just for show, it's a standard chineese riser with a common power delivery, and molex connector. The internal layers have been completely rebuilt, the PCB will be a bit larger and more resistant, with more features and passive heat management. I will grant even the most important protections, like OCP and OPP. The MSC-1, and the MSC-1b (motherboard adapter) will be used in our solutions, potentially built and used in our farm.

[Nikolaj]

from the picture it shows a few question...

1. Why do you need such high powered PSU?

2. Why the expensive board with 7 slot but only 5 boards on each setup?

3. Pros and Con about your risers.

1) a system with 7 VGAs could imply some very different configurations, for example:

7x RX480 = 1130W DC peak (under full load, with intensive algos)
7x R9 290 = 2320W DC peak
4x HD 7990 = 1800W DC peak

The first config it's an easy one, the latter not. Right now we're having low TDP VGA's but this is just a scenario, and whoever wants to scale up, giving to the customers (and mainly himself) a unit capable of delivering juice, in full stability and reliability with proper secondary elements, with such power hungry configs, will need such systems.

Think about a config with 7x RX 590 (VEGA) up to 250W TDP/VGA. This is the main objective, and my systems will be perfectly compatible (like no other, that are using common ATX power supplies instead of dedicated ones)

2) because it was just a setup for 5x 2.5 VGAs. Remember that there are a lot of possible configurations, and in a 19"rack you cannot fit 7 GTX 1070 AMP Extreme for example, but just 5. That motherboard could be used up to 8 VGAs, but it will manage 7 2.0 slot VGAs as soon as the new retention plate it's ready (3 weeks). I'll update the compatibility of this chassis up to 7. The interesting thing is that you could even purchase the actual model and later on swap the VGA plate, because they will be extrudable (find me something like that in the market, you won't). It will be extrudable also the motherboard and PSU plate, and the fans units, like what expressed in the first post of this thread.

3) a lot, but I'll show them later on when I'll receive the new heavy duty cables. All this stuff built in Italy with proprietary projects and schematics, and I am pretty proud of it

[DiCE1904]

Wow these look really slick

[Nikolaj]

You will be astonished soon, my word

[prospecting]

very cool stuff here.
any prices yet? or at least a price-range?
thanks

[Nikolaj]

very cool stuff here.
any prices yet? or at least a price-range?
thanks

Hi

No updates until now due a new kind of features that I've implemented in my latest designs. What you've seen it's just a fraction of the latest revision, in 10/12 days I should have got the final design.

A KEY FEATURE it's the possibility to cut hugely the expedition costs, due a complete redesign of the plates, that will permit a very high density in the package. This means that they wil need to be assembled like ikea, but it will cost a lot less to receive them, especially with high orders.

New elements:

- modular vga+riser component, that will be purchasable separately
- 7 dual slot capability in the first revision (later on 6 2.25 slot, like the inno3d ichill x4 gtx 1070)
- modular anterior and posterior plates, to boost the mainteance
- modular 4x 92x38mm fan cage, that could be swapped later on to insert a 3x 120mm config or 3x 140mm (eventually, low priority mod)
- plate compatibility with arduino
- up to 1 3.5" hdd and 2x 2.5" ssds in a proprietary cage, along a 7990 upon the moderboard with a 16x pcie interface
- compatibility up to 7x 30cm vgas in the front (vgas plate) and 2x posterior (motherboard plate) -1with the cage

You can use this chassis as an ordinary pc/testing platform

Contact me on facebook or gmail if you want to know more or get in touch.

These solutions are totally brand new, specifically designed from scratch for massive mining purposes, up to 7x 300W tdp 30cm VGAs in the posterior part, and up to 2x 29cm VGAs in the front, upon the motherboard (with our PSU designs, that we'll use at first within our custom solutions in the proprietary farm)

[Nikolaj]

First post updated 

Have a look. Feel free to contact me on facebook, for a chat and details

[Nikolaj]

One step closer:




One of the best, if not the best, tipology in the market:

- gold pins, for the best quality, contact and reliability
- 16AWG in the termination side
- hand-tested, 2 year warranty. No-question-answered in the return policy. We're simply OVER-CONFIDENT about these solutions, because we can guarantee you the best
- one of the 13th variants possible
- soon, with another version that will alow you to lower the amount of ripple (it could lead to obtain higher frequencies on the VGA, Overclock)

In more than a week...drumroll... the NEW CHASSIS REVISION with all the features mentioned in the first post.

[Nikolaj]

Sorry for the lack of updates but we've had so many, internal and external, needs that the current selling phase it's on hold

Thanks

[DiCE1904]

Sorry for the lack of updates but we've had so many, internal and external, needs that the current selling phase it's on hold

Thanks

Thanks for the update

[Nikolaj]

Sorry for the lack of updates but we've had so many, internal and external, needs that the current selling phase it's on hold

Thanks

Thanks for the update

Hi Dice1904

General News: due internal needs I haven't updated the final releases.

We're using them directly, because they've become so good that we're proceeding with patents, and internal use. I am developing another 3 versions, that I intend to sell:

- 5, or 6, VGA 4U 19" rack version, 1x ATX with ordinary cooling (150W TDP VGAs)
- 7 VGA 4U 23" non-rackable version (proprietary shelves and racks), 2x ATX with ordinary cooling (150W TDP VGAs)
- 6, or 7, VGA 8U 19" chassis, 1, or 2, ATX with ordinary cooling (150W TDP VGAs)

They can be shipped easily, due a dismountable concept, totally modular.
Very high quality of the frames, and robustness.

We're concentrating, for now, to use the top-of-the-line units internally.

The good news is that we could also OEM them, because we've become a mechatronic producer in the meantime.

If you've got proposals or ideas, or eventually a custom unit, we could have a talk on skype. We can design and realize new concepts, and produce them massively, shipping them worldwide.

If you're interested contact me on Skype, you'll find the address in the first post

Skype MT-EMC
Email cryptenergy@gmail.com
Facebook https://www.facebook.com/NikolajWojdelko
 

[chrysophylax]

modular design is the way to go ...

i believe this would ease delivery - and make it a more compact system to pack ...

keep it up mate ...

#crysx

[muratizm]

Where are the promised made-in-italy pci risers??

[Nikolaj]

Hi

General News: due internal needs I haven't updated the final releases.

We're using them directly, because they've become so good that we're proceeding with patents, and internal use.

As simple as that: internal use, new designs and no need for resell

You can see an hint of my own developments in my avatar. Right now there's no need of further details, thanks.

[AORNET]

My Contacts:
feel free to contact me, but please send first a PM presenting who you are. If I don't respond please write here your name, or send me a PM, and I will double check.

Skype MT-EMC
Facebook https://www.facebook.com/NikolajWojdelko

ps: all the Ideas, project, schematics, tests, patents and details are property of Matteo Trinca. They've been personal developments from February 2014, prior the constitution of the company. The sole owner of the projects and concept is myself. The company has ceased to exist (internal reasons), but the projects are finalized (hint: have a look at my avatar   )

The Account "Nikolaj" has been Blocked by me, Matteo Trinca.

It has been hacked this morning at 07:09.

DO NOT SEND BTCs to this user until I regain access. I will notify here IF/When. If I cannot, it will be blocked forever.

By the way, to the hacker, I was going to utilize this one for the New Operations. Think about your failures instead of the other successful activities, you miserable.

Let's put a preview, to let you feel pain (I've got some ideas about who is behind this action).

SCREEN OF THE LATEST 6x 300W VGA GPU CHASSIS - AORNET VENERE

https://i.imgur.com/idodMtmm.jpg

http://www.repubblica.it/economia/affari-e-finanza/2017/10/16/news/tesori_allasta_si_paga_con_il_bitcoin-178417677/

Matteo "Nikolaj" Trinca

[pallas]

Matteo don't get mad at this hacking shit.
A lot of users got hacked, it's a mass operation without any specific target.

Oss!

[AORNET]

Matteo don't get mad at this hacking shit.
A lot of users got hacked, it's a mass operation without any specific target.

Oss!

Thanks mate

Btw It's just matter of time. Thankfully all the other websites that I've got have a way more complex pw system, unhackable. This was an old one, and I've forgot to update it given the low usage in the last year

Oss !