boody123 (OP)
Newbie
Offline
Activity: 5
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/sad.gif) |
October 12, 2016, 05:36:44 PM |
|
Hi, in one of my Antminer s9 Appears only 2 hash board chips on Miner Status not 3 , this happens after 4 day of working .. despite of I have connected all power cables right in their places I have checked with different power supplies , I have also change data cables but it doesn't Appear. https://i.imgur.com/z5NXokB.pnghttps://i.imgur.com/hch1KJQ.jpg
|
|
|
|
ZACHM
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 12, 2016, 06:59:48 PM |
|
Have you tried switching which port the ribbon cable to the controller is plugged in? This would eliminate whether it was the controller causing the problem or the board.
|
|
|
|
MyRig
Donator
Hero Member
Offline
Activity: 792
Merit: 510
support@myrig.com
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 12, 2016, 08:04:14 PM |
|
If your control PCB has 4 data port, please try using 1 unused port to connect to hash PCB that does not have red LED flashing near the PCI-E power plug when the miner is hashing. Other wise, if you can take a look at the hash PCB when the S9 is mining, you may notice one of the hash PCB does not have the little red LED on or flashing. (That is the PCB in trouble here) Hi, in one of my Antminer s9 Appears only 2 hash board chips on Miner Status not 3 , this happens after 4 day of working .. despite of I have connected all power cables right in their places I have checked with different power supplies , I have also change data cables but it doesn't Appear. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2Fz5NXokB.png&t=665&c=p6BajrO5jXj9YQ) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2Fhch1KJQ.jpg&t=665&c=DOQt2Qf1ZP7DhQ)
|
Antminer & DragonMint Repair E-mail: support@myrig.com T: @MyRig_com Return Address: MyRig 3700 Quebec Street, Unit 100-239, Denver, Colorado 80207, USA
|
|
|
NotFuzzyWarm
Legendary
Offline
Activity: 3724
Merit: 2646
Evil beware: We have waffles!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 12, 2016, 11:51:44 PM |
|
If your control PCB has 4 data port, please try using 1 unused port to connect to hash PCB that does not have red LED flashing near the PCI-E power plug when the miner is hashing. Other wise, if you can take a look at the hash PCB when the S9 is mining, you may notice one of the hash PCB does not have the little red LED on or flashing. (That is the PCB in trouble here) Hi, in one of my Antminer s9 Appears only 2 hash board chips on Miner Status not 3 , this happens after 4 day of working .. despite of I have connected all power cables right in their places I have checked with different power supplies , I have also change data cables but it doesn't Appear. <snip> @ BitmainWarranty: Is it possible to get a service report for the diagnosis/repair or exchange performed on the boards we send you for repair? I asked Ashi (?) about it but he is in the messaging end of your work, not the service tech that did the work. As a tech person myself (industrial laser design/research/repair) I would really like to know what failed on the 2 s9 boards I had you repair/replace. Both boards are working perfectly now btw. Great work and a very reasonable price/turnaround time. ![Cheesy](https://bitcointalk.org/Smileys/default/cheesy.gif) .
|
|
|
|
MyRig
Donator
Hero Member
Offline
Activity: 792
Merit: 510
support@myrig.com
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 13, 2016, 12:45:46 AM Last edit: October 13, 2016, 12:56:47 AM by BitmainWarranty |
|
Hi NotFuzzyWarm, unfortunately, we do not have resource available to provide full report on what was bad and what was done to complete the repair and what may have caused it. In order to keep the hash PCB repair cost reasonable while it is being diagnosed and repaired we are focusing on get it to work again and keeping the cost as low as possible. if we ask techs to produce written report on analysis, repair/diagnostic fee will exceed the cost of the parts attempting to repair. That will require us to have additional review layer that will cause additional man hours by multiple staffs. We are looking a way to communicate to the cusotmers when some major problem was detected as the user errror, in attempt to reduce the unnecessary damages to the other units. If you didn't not received any personal message about humidity or hardware modification or personally attempted to repair and ailed. We are seeing significant amount of failed repair attempted performed by someone in Venezuela without initially being disclosed that someone have already worked on it and further damaged the item from misdiagnosed or mistreated item. Those, customer will hear about why and sometimes how bad the damage was that was human made damage but if you have not received any communications from the techs, then you should be in a good shape Repair in Denver will diagnose item from failed 3rd party repair attempt, however, often time, if someone have failed the repair... chances are PCB already sustained additional damages and either possible to fix at very high price or exceed the cost of buying hte replacement and you will be notified options. If your control PCB has 4 data port, please try using 1 unused port to connect to hash PCB that does not have red LED flashing near the PCI-E power plug when the miner is hashing. Other wise, if you can take a look at the hash PCB when the S9 is mining, you may notice one of the hash PCB does not have the little red LED on or flashing. (That is the PCB in trouble here) Hi, in one of my Antminer s9 Appears only 2 hash board chips on Miner Status not 3 , this happens after 4 day of working .. despite of I have connected all power cables right in their places I have checked with different power supplies , I have also change data cables but it doesn't Appear. <snip> @ BitmainWarranty: Is it possible to get a service report for the diagnosis/repair or exchange performed on the boards we send you for repair? I asked Ashi (?) about it but he is in the messaging end of your work, not the service tech that did the work. As a tech person myself (industrial laser design/research/repair) I would really like to know what failed on the 2 s9 boards I had you repair/replace. Both boards are working perfectly now btw. Great work and a very reasonable price/turnaround time. ![Cheesy](https://bitcointalk.org/Smileys/default/cheesy.gif) .
|
Antminer & DragonMint Repair E-mail: support@myrig.com T: @MyRig_com Return Address: MyRig 3700 Quebec Street, Unit 100-239, Denver, Colorado 80207, USA
|
|
|
boody123 (OP)
Newbie
Offline
Activity: 5
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 13, 2016, 01:18:28 AM |
|
If your control PCB has 4 data port, please try using 1 unused port to connect to hash PCB that does not have red LED flashing near the PCI-E power plug when the miner is hashing. Other wise, if you can take a look at the hash PCB when the S9 is mining, you may notice one of the hash PCB does not have the little red LED on or flashing. (That is the PCB in trouble here) Hi, in one of my Antminer s9 Appears only 2 hash board chips on Miner Status not 3 , this happens after 4 day of working .. despite of I have connected all power cables right in their places I have checked with different power supplies , I have also change data cables but it doesn't Appear. https://i.imgur.com/z5NXokB.pnghttps://i.imgur.com/hch1KJQ.jpgHi BitmainWarranty, all of them having red LED flashing when the miner is hashing , even the PCB that facing the trouble and doesn't Appears on Miner Status Page
|
|
|
|
MyRig
Donator
Hero Member
Offline
Activity: 792
Merit: 510
support@myrig.com
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 13, 2016, 01:34:34 AM |
|
in that case, you may want to test 1 hash PCB at a time, to identity which PCB will hash and which one does not. 1 hash PCB connected to the control module at a time Hope this can help you find which one is bad If your control PCB has 4 data port, please try using 1 unused port to connect to hash PCB that does not have red LED flashing near the PCI-E power plug when the miner is hashing. Other wise, if you can take a look at the hash PCB when the S9 is mining, you may notice one of the hash PCB does not have the little red LED on or flashing. (That is the PCB in trouble here) Hi, in one of my Antminer s9 Appears only 2 hash board chips on Miner Status not 3 , this happens after 4 day of working .. despite of I have connected all power cables right in their places I have checked with different power supplies , I have also change data cables but it doesn't Appear. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2Fz5NXokB.png&t=665&c=p6BajrO5jXj9YQ) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2Fhch1KJQ.jpg&t=665&c=DOQt2Qf1ZP7DhQ) Hi BitmainWarranty, all of them having red LED flashing when the miner is hashing , even the PCB that facing the trouble and doesn't Appears on Miner Status Page
|
Antminer & DragonMint Repair E-mail: support@myrig.com T: @MyRig_com Return Address: MyRig 3700 Quebec Street, Unit 100-239, Denver, Colorado 80207, USA
|
|
|
boody123 (OP)
Newbie
Offline
Activity: 5
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 13, 2016, 01:44:46 PM |
|
in that case, you may want to test 1 hash PCB at a time, to identity which PCB will hash and which one does not. 1 hash PCB connected to the control module at a time Hope this can help you find which one is bad If your control PCB has 4 data port, please try using 1 unused port to connect to hash PCB that does not have red LED flashing near the PCI-E power plug when the miner is hashing. Other wise, if you can take a look at the hash PCB when the S9 is mining, you may notice one of the hash PCB does not have the little red LED on or flashing. (That is the PCB in trouble here) Hi, in one of my Antminer s9 Appears only 2 hash board chips on Miner Status not 3 , this happens after 4 day of working .. despite of I have connected all power cables right in their places I have checked with different power supplies , I have also change data cables but it doesn't Appear. https://i.imgur.com/z5NXokB.pnghttps://i.imgur.com/hch1KJQ.jpgHi BitmainWarranty, all of them having red LED flashing when the miner is hashing , even the PCB that facing the trouble and doesn't Appears on Miner Status Page @BitmainWarranty, I have tried to do this before and figure it out which one PCB that facing the trouble and doesn't work (I uploaded a pic of PCB below and marked it with a red circle and arrows) the question here what I should do to fix it ? https://i.imgur.com/Mhgn8rk.jpg
|
|
|
|
ZACHM
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 13, 2016, 01:58:37 PM |
|
I'm a little confused by your wording.
Did you try each board one at a time to determine which one is not working?
Did you try each data port with that board to determine it is the board and not the port it is plugged into?
Did you try using a different cable to determine if it is the cable?
If you have determined that after the above it is the board and you are still under warranty then you should be able to get it repaired. You could also possibly get it repaired if not under warranty, but it will cost you.
|
|
|
|
boody123 (OP)
Newbie
Offline
Activity: 5
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 13, 2016, 04:45:22 PM |
|
I'm a little confused by your wording.
Did you try each board one at a time to determine which one is not working?
Did you try each data port with that board to determine it is the board and not the port it is plugged into?
Did you try using a different cable to determine if it is the cable?
If you have determined that after the above it is the board and you are still under warranty then you should be able to get it repaired. You could also possibly get it repaired if not under warranty, but it will cost you.
yea I have tried all of these things and determined which board it doesn't work .... and i'm still under warranty until now
|
|
|
|
NotFuzzyWarm
Legendary
Offline
Activity: 3724
Merit: 2646
Evil beware: We have waffles!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 13, 2016, 05:13:15 PM Last edit: October 14, 2016, 12:55:58 AM by NotFuzzyWarm |
|
I'm a little confused by your wording.
Did you try each board one at a time to determine which one is not working?
Did you try each data port with that board to determine it is the board and not the port it is plugged into?
Did you try using a different cable to determine if it is the cable?
If you have determined that after the above it is the board and you are still under warranty then you should be able to get it repaired. You could also possibly get it repaired if not under warranty, but it will cost you.
yea I have tried all of these things and determined which board it doesn't work .... and i'm still under warranty until now Since you have been following the advice from Bitmain Warranty for the testing, the only thing affecting warranty status is the 90-day time limit. I had a b11 board go out -- still technically under the 90-days -- but sent it to BitmainWarranty anyway for them to do the repair/exchange. Got it back 1week later, cost was $145 inc the return shipping. Yes was a little higher than sending to China for (possibly/probably 'free') repair but: 1. I was able to ship the board to BitmainWarranty using USPS insured for full value. I declared $400. Sending to China you have to declare value under $40 or face Customs scrutiny and the associated extra cost/time it takes, so if it gets lost or damaged in-transit you are screwed. USPS fully insured w/tracking was $21. 2. No issues with who-did-what, what on it died and is it covered by warranty, etc.
|
|
|
|
|