[ANN][CNC][1% Fee] CNC Simple Pool [LP/Stratum]

[peacefulmind]

Good BYE CNC, Dontmine me is about to get 51%
"Registration has been temporarily closed due to the large hash rate on this server relative to the total hash power of the network.
It will reopen when the pool/network hash rate (50.54%) drops below 35%


Thank you for your support!"

http://cnc.dontmine.me/register

I've had >51% before actually, on both FTC and CNC, and gotten 6 blocks in a row several times (not that any pool should have 51%). I close registration, but someone has been selling accounts apparently on btc-e. I'm trying to be a good pool citizen here, but it's hard!

Paul,

Wish you would combine these pools like Coinotron.  I have had ~9000Kh/s pointed at your FTC pool through all the difficulties it had with stratum but stuck with it.

It is frustrating not to be able to switch a few of those to CNC because I do not have a separate registration here. 

[1715006626]

1715006626

[1715006626]

1715006626

[1715006626]

1715006626

[storm11]

for the past few minutes, my miners have reported "Can't create UNIX so". 2 separate computers. Pool issues? It's causing quite a few rejected shares. I had already set queue to 0 and expiry to 1

[ElJay]

for the past few minutes, my miners have reported "Can't create UNIX so". 2 separate computers. Pool issues? It's causing quite a few rejected shares. I had already set queue to 0 and expiry to 1

Same here! But atleast the pool is running now 

[erk]

Getting this mass of errors that say:

Rejected     ((2001, "Can't create UNIX so)

[paul21]

I increased the file limit but I forgot to restart my session before I opened stratum server, oh well it's bumped now should be good

[storm11]

issue definitely resolved. looking forward to you increasing the difficulty of submitted shares, still at 10% stale rate despite dropping intensity, queue to 0 and expiry to 1. The high number of miners on the site has affected my shares, 17.5CNC would take an hour to pay out for a couple of hours, then 1hr 15mins, now 1hr 30 mins. Don't know if it is just bad luck, but with the huge number of workers, wouldn't have thought the luck would be that bad....

[crymo]

pool is running great, but i have still hugh number of stales 1750/300... trying to lower intensity by 2

[rikii]

paul do you still suggest trying "--queue 0 --expiry 1" since you've increased the files size. The blocks are solving so fast often i cant get an accepted share in before the next and it causes both my hash rate and my expected round pay to decrease significantly. Thanks for your input.

[erk]

Looks like it's over the 51%

Net Hash: 2729.58 MH/s   
   
Pool Hash: 1451.5 MH/s

Not good.

[Mhash pipe]

Great pool! Now donating 1%

[phrozenspite]

Why is everyone concerned about the 51% thing. The khore pool on novacoin has something like 66% and I'm sure coinotron has to have at least 50% of the freicoin hash. 

[Frizz23]

I get timeout while accessing http://cnc.dontmine.me

Is this pool gone?

[erk]

Why is everyone concerned about the 51% thing. The khore pool on novacoin has something like 66% and I'm sure coinotron has to have at least 50% of the freicoin hash. 

Have you already forgotten about the 51% attack that BBQCoin had just after launch?

[phrozenspite]

Difficulty just went to 20, any recommended changes for us Paul?

[Frizz23]

Can you still access the web frontend http://cnc.dontmine.me ?

Seems to be down .....

[phrozenspite]

working fine here

[Frizz23]

cnc.dontmine.me seems to be most of the time down.

[FaT]

I keep getting Rate limit exceeded messages when I browse the site.. I'm guessing you need more bandwidth?

[crymo]

very good pool, after lowering intensity to 18 only 2,5% stale. Also no disconections..ty mate

[rayman]

Hi,
I have a problem: I was mining for about 10 hours at 2nd May and still not received any reward to my wallet.
I was connected with cgminer this way:

cgminer.exe --scrypt -o http://cnc.dontmine.me:33334 -u CRnvmTjAa8f616KdU9ShyUkkWarN8X8yaJ -p x

So where can I find how many coins I have and how to withdraw them? Did I forget something?

Thanks in advance.