Riserless Mining Motherboards the death of PCIE risers? Mining Rig Tear Down!

[VoskCoin]

Hey everyone I made a video covering some of the basics of the newer riserless motherboards along with pcie risers as well as tearing down Mining Cave's new riserless gpu mining rig -- they will be releasing the rig kit (gpu miner. . minus the gpus) soon for sale and said everyone can use coupon code VoskCoin for 3% off fwiw

https://youtu.be/Yz3N3exALpA


What are your thoughts on these riserless mobo rig setups?

[1714677281]

1714677281

[1714677281]

1714677281

[NameTaken]

I think the spacing is a bit too tight for 200W+ 1080Tis so I'm planning on using 120W 1070Tis with these boards and continue using traditional risers for 1080Tis.

[nc50lc]

I've seen this coming since that GPU mining craze.
These might go along with the case made by the manufacturers themselves. sssSmells profit.
Looks like they taken the opportunity to make one, but others will, overtime.

For stability, these might be the solution.
The whole unit was designed to work together unlike regular Mobo with couple of Risers.

The design though, this doesn't look innovative at all.
It looks like a stretched gaming rig.

[yhhy]

I'm planning on trying out one of these, but the spacing might be a problem

[VyprBTC]

Tough call because I've had absolutely ZERO issues with risers, besides a dead one here and there but I always order twice as many as I need and refund the rest so it never matters.

[adaseb]

Riserless mobo's?

USB Risers?

Nah, my rigs are still using the ribbon risers. 2013-2014 mining FTW

[Vann]

Dual mining for 8+ months on USB risers and zero issues as well. For mining, risers are advancement from having to cram multiple GPU's on to a motherboard. These boards are a step backwards IMO, unless you plan to cram them in to a server rack.

[philipma1957]

These boards are great with Evga hybrid 1080 ti

The pre loaded waterblocks do 700+ and run cool

I have four six card 1080ti rigs each do 4200 sols.

Riser rigs are meh compared to these rigs.

[KaydenC]

I buy the mobos along with the server cases. With 4x 3700rpm fans, even 1080tis are kept below 70 degrees at 77% PL. Both blower and dual fans one work well. (Except for Inno3d twinx2 which has a terrible cooling solution)

[VyprBTC]

These boards are great with Evga hybrid 1080 ti

The pre loaded waterblocks do 700+ and run cool

I have four six card 1080ti rigs each do 4200 sols.

Riser rigs are meh compared to these rigs.

I do agree with you that the Hybrid 1080 Ti's are AWESOME - I'm up to 25 now, mix of EVGA and the Corsairs but they are awesome. I'm really seriously thinking about buying the hybrid kits for the rest of the cards since I maxed out power and grid won't handle an AC but I'd have to spend another $22k for all the upgrade EVGA kits.

So I'm now thinking about testing maybe an EKWB waterblock but not sure. We shall see.

[Turkish88]

Looks like good but space between GPU very low, With risers i can buld more effience rig.
With this mobo need to delete stock cooling system and create side winding system

[VyprBTC]

I did forget to mention a big thank you to Phil because without his suggestion I would never be using Hybrid Coolers, so thanks Phil! You are the man!

[HagssFIN]

Riserless mobo's?

USB Risers?

Nah, my rigs are still using the ribbon risers. 2013-2014 mining FTW

Damn those ribbon risers were dangerous for me back in the 2014, I still remember one suddenly bursting in to burning and lots of smoke because of that.  

Nothing else than the riser was damaged, luckily. Maybe I just ended up with a bad quality batch one, but I would be careful using those.

[adaseb]

Riserless mobo's?

USB Risers?

Nah, my rigs are still using the ribbon risers. 2013-2014 mining FTW

Damn those ribbon risers were dangerous for me back in the 2014, I still remember one suddenly bursting in to burning and lots of smoke because of that.  

Nothing else than the riser was damaged, luckily. Maybe I just ended up with a bad quality batch one, but I would be careful using those.

Its probably because you didn't cut the +12V line going into the motherboard.

Some suppliers cut this for you... some lazy ones didn't.

So what happened was you were feeding +12V from Molex and a parallel +12V was supplied by the motherboard. Since the voltages were exactly +12V, some current feedback loop was created and BOOM!

[HagssFIN]

If I remember right, I noticed the reason was  a loose Molex connector wires connection to the riser board, bad soldering work.

[MagicSmoker]

I've been running an Onda D1800 6-GPU mobo for over a week continuously now mining ZEN. It's an all GTX 1060 setup (don't laugh - it's all I could find that wasn't priced so high it should've come with a bottle of anal lube) so not the highest power but keeping it cool has been a challenge. Right now I have a box fan suspended above and behind it to keep temps below 70C - and note that total power draw at the wall for this rig is 700W (300W to the mobo and 400W to the GPU PCIe power inlets).

The Untel Celery® CPU is slow as Christmas but gets the job done as long as you don't interact with the desktop too much. It's been very stable with no crashes or strange GPU nonsense once I got the O/C dialed in for each card (4 are the same and 2 are both different). The built-in VGA port on mine works (v2.00) and though it made initial setup a challenge (lol, VGA), I was able to scrounge up an old LCD monitor from a local computer recycling outfit.

Overall I am very pleased with the performance and if the PCIe slot spacing were just increased from 5cm to 6cm I think this would be a real winner.

[grickie77]

Question: can these boards operate with spaces empty? say with 4 cards? Different versions of 580's ok?

Would think so but I haven't seen it covered yet. Thanks!

[VoskCoin]

Question: can these boards operate with spaces empty? say with 4 cards? Different versions of 580's ok?

Would think so but I haven't seen it covered yet. Thanks!

yes that is no issue / can skip slots and use different cards

[jonsal]

Can you please post some temperature data on those Zotac 1070 ti mini's? How did the 8 of them do in the case over a period of time?

[vapourminer]

love my onda b250 d8p v1. will never build a riser rig again.

some of those riserless boards have better slot spacing than others, the d8p v1 is very good with 2.5 spacing. i dunno how well a 2.0 spacing board will do cooling wise.

but the d8p with its 2.5 spacing will not fit in a server case whereas a board with 2.0 spacing would.

one thing i will always want in a riserless board is a socket for the cpu rather than a built in. just personal preference.