tdxminer lyra2z/XZC Miner for AMD GPUs on Linux

[N2DCRYPT]

This miner it's not the best miner for Lyra2z. It's best from public miners

Think there are hidden miners with the best speed for personal use?

go to pools where you can mine GIN or MANO and look at page Miners. You can find there unknown miners including sgminer not from djm34 (which has very poor optimization) with higher than tdxminer average hashrate. So it's not my fantasy. Also this unknown miners may be used with NiceHash or at solo mining or at not public pools.

If this were true you wouldn't be spending so much time posting in this sub about this miner. Don't waste people's time chasing down some "unknown" miner.

[deksa]

Guys?
How much coins do you do daily per 1080 Ti?
After 24 hours constant mining 3.7 mh/s here and doing 0.125 Gin and I think that is way too low.
Anyone want to share?

[HaloGenius]

Guys?
How much coins do you do daily per 1080 Ti?
After 24 hours constant mining 3.7 mh/s here and doing 0.125 Gin and I think that is way too low.
Anyone want to share?

Diff is too high now ... sweat times already behind
There Nicehash and maybe FCPGA

[artful]

i have vega 56, install ubuntu 16.04
install  https://github.com/RadeonOpenCompute/ROCm

launch miner:

Code:

[2018-06-28 01:47:39] Successfully initialized GPU 0: Vega with 56 CU
[2018-06-28 01:47:40] Dev pool connected and ready.
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca successfully subscribed.
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca authorization succeeded.
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca set difficulty to 1.000000
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca extranonce subscribe succeeded.
[2018-06-28 01:48:00] Pool lyra2z.mine.zpool.ca received new job. (job_id: b9d)
[2018-06-28 01:48:05] Pool lyra2z.mine.zpool.ca received new job. (job_id: ba2)
[2018-06-28 01:48:09] Pool lyra2z.mine.zpool.ca received new job. (job_id: b9f)
[2018-06-28 01:48:20] Pool lyra2z.mine.zpool.ca received new job. (job_id: bab)
[2018-06-28 01:48:39] Stats GPU 0 - 
[2018-06-28 01:48:47] Pool lyra2z.mine.zpool.ca received new job. (job_id: bae)
[2018-06-28 01:48:48] Pool lyra2z.mine.zpool.ca received new job. (job_id: bad)
[2018-06-28 01:49:04] Pool lyra2z.mine.zpool.ca received new job. (job_id: bb4)
[2018-06-28 01:49:25] Pool lyra2z.mine.zpool.ca received new job. (job_id: bb6)
[2018-06-28 01:49:27] Pool lyra2z.mine.zpool.ca received new job. (job_id: bb7)
[2018-06-28 01:49:39] Stats GPU 0 - 

Code:

/opt/rocm/bin/rocm-smi

====================    ROCm System Management Interface    ====================
================================================================================
 GPU  Temp    AvgPwr   SCLK     MCLK     Fan      Perf    SCLK OD
  0   47.0c   27.0W    1538Mhz  800Mhz   12.94%   auto      0%       
================================================================================
====================           End of ROCm SMI Log          ====================

no mine speed, no avgpwr 

[du44]

Dev, what's about some listening of community voice? A lot of people waiting for windows version. You didn't wrote something last 2-3 weeks. It's not best way to increase number of your miner users.

[Anthony42]

Dev, what's about some listening of community voice? A lot of people waiting for windows version. You didn't wrote something last 2-3 weeks. It's not best way to increase number of your miner users.

People do not understand anything, even if it appears on windows, then you will immediately go to dig again ETH, because the complexity is such that the income will be 0.5 usd to card/day for 3 mh/s, and then at best.

[hamdyahmed1984]

Tried TDXMiner on HiveOS for 6 RX580 cards and get 3.7 for each card.
These are my overclock/down voltage:
CORE 1340 DPM 1 V 1050 MEM 1800 FAN 50

Thanks for your awesome miner (Y)

[artful]

who install drivers on ubuntu 16.04 for vega 56/64, please help

https://bitcointalk.org/index.php?topic=3299496.msg41037175#msg41037175

[preda]

Tried TDXMiner on HiveOS for 6 RX580 cards and get 3.7 for each card.
These are my overclock/down voltage:
CORE 1340 DPM 1 V 1050 MEM 1800 FAN 50

Thanks for your awesome miner (Y)

Wow bro... You are consuming lots of electricity...

Here my tests on hiveos: 2x 480 8gb 2x 480 4gb

All default settings i get  3.4mh for 8gb cards and 3.2mh for 4gb cards with power consumption of 740watt on the wall.....

I put aggressive underclock in hiveos and vm940 and the speed is 3.3mh for 8gv cards and 3.1mh for 4gb so i lost nothing about hashrate, but 500watt from the wall total!!!! I'd say lyra2z it's fresh for summer

[williet]

24 Vega 64's here waiting for Windows.

Is it possible to have more than 6 Vega per rig?

Yes, on linux

[kedes]

Could anybody post or give a link to detailed guide how to install ubuntu, install drivers and then download and run tdxminer please?

...
Then you have a new Folder called tdxminer.... open it. In zhis folder you need a .sh-file to use the miner too, there is no sh-file within the package. a SH-File is like a .BAT-File in Windows, you can edit it with Notepad or something like that.

So you can create a simple Doc, right Mouseclick, new document
In that you wrote ./tdxminer -a lyra2z -o stratum+tcp://eu1.fairmine.pro:4553 -u se345rwijhoseifglerkhfh -p c=BTC

-a is for th Algorithm you want to mine. -o is for the pool. -u is for your Walletadress. -p is for the Poolpasswort, if needed, mostly its only x. c is for the Short of the Coin, e.j. Bitcoin is BTC.

Save the file ,thats it.

Now you can doubleclick on the SH-File, Ubuntu ask what to do with that file-type, choose that Ubuntu schould use it as executable file. Now it will start as program everytime you click on it. Sometimes Ubuntu dont know a sh-file. Then open a Terminal in that folder, type chmod a+x FILENAMe.sh and press Enter. Then doubleclick the sh-file again.

Sh file doesnt work. I placed in it: "./tdxminer -a lyra2z -o stratum+tcp://eu1.fairmine.pro:4553 -u se345rwijhoseifglerkhfh -p c=BTC" and named it as RUN.sh. Then i tried to Open it with Run Software but nothing happens. What's wrong?
Then i tried to run " sudo ./tdxminer -a lyra2z -o stratum+tcp://eu1.fairmine.pro:
4553 -u se345rwijhoseifglerkhfh -p c=BTC" in the terminal. But it says @Failed to list OpenCL platforms.@
 What's wrong? I installed ROCm 1.8.1 drivers and libjasson4 libraries before.

[veritech]

Yeah there is no other miner in the background.
Can you tell me if you have the GPUs factory BIOS or you changed it?
What is your power draw and clock settings?

stock everything. what motherboard are you using?

[sidaliroy]

When Windows version?

[SimpleM]

i have vega 56, install ubuntu 16.04
install  https://github.com/RadeonOpenCompute/ROCm

launch miner:

Code:

[2018-06-28 01:47:39] Successfully initialized GPU 0: Vega with 56 CU
[2018-06-28 01:47:40] Dev pool connected and ready.
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca successfully subscribed.
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca authorization succeeded.
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca set difficulty to 1.000000
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca extranonce subscribe succeeded.
[2018-06-28 01:48:00] Pool lyra2z.mine.zpool.ca received new job. (job_id: b9d)
[2018-06-28 01:48:05] Pool lyra2z.mine.zpool.ca received new job. (job_id: ba2)
[2018-06-28 01:48:09] Pool lyra2z.mine.zpool.ca received new job. (job_id: b9f)
[2018-06-28 01:48:20] Pool lyra2z.mine.zpool.ca received new job. (job_id: bab)
[2018-06-28 01:48:39] Stats GPU 0 - 
[2018-06-28 01:48:47] Pool lyra2z.mine.zpool.ca received new job. (job_id: bae)
[2018-06-28 01:48:48] Pool lyra2z.mine.zpool.ca received new job. (job_id: bad)
[2018-06-28 01:49:04] Pool lyra2z.mine.zpool.ca received new job. (job_id: bb4)
[2018-06-28 01:49:25] Pool lyra2z.mine.zpool.ca received new job. (job_id: bb6)
[2018-06-28 01:49:27] Pool lyra2z.mine.zpool.ca received new job. (job_id: bb7)
[2018-06-28 01:49:39] Stats GPU 0 - 

Code:

/opt/rocm/bin/rocm-smi

====================    ROCm System Management Interface    ====================
================================================================================
 GPU  Temp    AvgPwr   SCLK     MCLK     Fan      Perf    SCLK OD
  0   47.0c   27.0W    1538Mhz  800Mhz   12.94%   auto      0%       
================================================================================
====================           End of ROCm SMI Log          ====================

no mine speed, no avgpwr 

Just follow the driver setup guide on https://rocm.github.io/ROCmInstall.html


and to make sure all your cards mine, load your miner by setting HSA_ENABLE_SDMA to zero first. eg:

Code:

:~# HSA_ENABLE_SDMA=0 /path/to/your/miner 

[artful]

i have vega 56, install ubuntu 16.04
install  https://github.com/RadeonOpenCompute/ROCm

launch miner:

Code:

[2018-06-28 01:47:39] Successfully initialized GPU 0: Vega with 56 CU
[2018-06-28 01:47:40] Dev pool connected and ready.
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca successfully subscribed.
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca authorization succeeded.
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca set difficulty to 1.000000
[2018-06-28 01:47:40] Pool lyra2z.mine.zpool.ca extranonce subscribe succeeded.
[2018-06-28 01:48:00] Pool lyra2z.mine.zpool.ca received new job. (job_id: b9d)
[2018-06-28 01:48:05] Pool lyra2z.mine.zpool.ca received new job. (job_id: ba2)
[2018-06-28 01:48:09] Pool lyra2z.mine.zpool.ca received new job. (job_id: b9f)
[2018-06-28 01:48:20] Pool lyra2z.mine.zpool.ca received new job. (job_id: bab)
[2018-06-28 01:48:39] Stats GPU 0 - 
[2018-06-28 01:48:47] Pool lyra2z.mine.zpool.ca received new job. (job_id: bae)
[2018-06-28 01:48:48] Pool lyra2z.mine.zpool.ca received new job. (job_id: bad)
[2018-06-28 01:49:04] Pool lyra2z.mine.zpool.ca received new job. (job_id: bb4)
[2018-06-28 01:49:25] Pool lyra2z.mine.zpool.ca received new job. (job_id: bb6)
[2018-06-28 01:49:27] Pool lyra2z.mine.zpool.ca received new job. (job_id: bb7)
[2018-06-28 01:49:39] Stats GPU 0 - 

Code:

/opt/rocm/bin/rocm-smi

====================    ROCm System Management Interface    ====================
================================================================================
 GPU  Temp    AvgPwr   SCLK     MCLK     Fan      Perf    SCLK OD
  0   47.0c   27.0W    1538Mhz  800Mhz   12.94%   auto      0%       
================================================================================
====================           End of ROCm SMI Log          ====================

no mine speed, no avgpwr 

Just follow the driver setup guide on https://rocm.github.io/ROCmInstall.html


and to make sure all your cards mine, load your miner by setting HSA_ENABLE_SDMA to zero first. eg:

Code:

:~# HSA_ENABLE_SDMA=0 /path/to/your/miner 

Thank you, miner is working

question set core clock

Code:

 /opt/rocm/bin/rocm-smi --showclocks

====================    ROCm System Management Interface    ====================
================================================================================
GPU[0] 		: GPU Clock Level: 4 (1312Mhz)
GPU[0] 		: GPU Memory Clock Level: 3 (800Mhz)
================================================================================
====================           End of ROCm SMI Log          ====================


/opt/rocm/bin/rocm-smi --showclkfrq 
====================    ROCm System Management Interface    ====================
================================================================================
GPU[0] 		: Supported GPU clock frequencies on GPU0
GPU[0] 		: 0: 852Mhz 
GPU[0] 		: 1: 991Mhz 
GPU[0] 		: 2: 1138Mhz 
GPU[0] 		: 3: 1269Mhz 
GPU[0] 		: 4: 1312Mhz *
GPU[0] 		: 5: 1474Mhz 
GPU[0] 		: 6: 1538Mhz 
GPU[0] 		: 7: 1590Mhz 
GPU[0] 		: 
GPU[0] 		: Supported GPU Memory clock frequencies on GPU0
GPU[0] 		: 0: 167Mhz 
GPU[0] 		: 1: 500Mhz 
GPU[0] 		: 2: 700Mhz 
GPU[0] 		: 3: 800Mhz *
GPU[0] 		: 
================================================================================
====================           End of ROCm SMI Log          ====================

me try:

Code:

/opt/rocm/bin/rocm-smi --setfan 255 --setsclk 5


====================    ROCm System Management Interface    ====================
GPU[0] 		: Successfully set GPU Clock frequency mask to Level 5
GPU[0] 		: Successfully set fan speed to Level 255
====================           End of ROCm SMI Log          ====================

and no effect, level GPU = 4

[deksa]

Can anyone please send me a link of a Bios or how to set one up? My RX 580gb hash is 1.4 mhs and it is a disaster. Using Tdxminer on HiveOS with stocks settings.

[AlexApets]

Can anyone please send me a link of a Bios or how to set one up? My RX 580gb hash is 1.4 mhs and it is a disaster. Using Tdxminer on HiveOS with stocks settings.

you need to download  BIOS from you card,  edit 4 fields  raising them by 25% (for example) and flashing  BIOS back.  above given link to raise PL in  hive OS - everything is there

done only that I raised  hashrate from 2.2-2.5 to 3-3.1 on rx470/rx570 4gb

but if you have a strong undervolt in  BIOS, you may also have to raise  voltage, in my case, only memory timings were simply stitched for ETH

[preda]

Can anyone please send me a link of a Bios or how to set one up? My RX 580gb hash is 1.4 mhs and it is a disaster. Using Tdxminer on HiveOS with stocks settings.

al my 480 card reach 3.4/3.2mh
just flash bios mod and on hiveos ive put aggressive underclock and 940mv

[hiron1986]

anyone know what pool to use? I tried to use nicehash lyra2z but got socket closed error everytime.

[HaloGenius]

anyone know what pool to use? I tried to use nicehash lyra2z but got socket closed error everytime.

tdx works perfectly with nicehash - just review your settings