[CLOSED] batch #39 0.25 btc per Blade, backplanes .15

[Abraxas601]

Two Blades

5f247351a6923f31eb1424721f8035a00da876ed598e8209c3de351e0b2c11c2

[1714748162]

1714748162

[1714748162]

1714748162

[1714748162]

1714748162

[1714748162]

1714748162

[1714748162]

1714748162

[CanaryInTheMine]

Two Blades

5f247351a6923f31eb1424721f8035a00da876ed598e8209c3de351e0b2c11c2

shipped. thanks!

[CanaryInTheMine]

I see the backplane comes with 10 or more but will you sell them individually?

they are reserved for orders of 10 atm.  if I happen to sell alot of individual blades and a few backplanes become "freed up" then I post their availability.

I have some backplanes that are now freed up.

[sebdude420]

I have done a lot of orders lately, can you save me one of those "freed" up backplanes?

[artbatista]

Yes, I still have blades.  Have received several PMs asking about them.
Thanks!

These are v2 blades?

Art

[twib2]

Hi Canary - one blade por favor:

0754703166b569cf254b9140652b83c787549c2a79d5c28d0343bef79f786fb1
124jzM8sHhSit8LkV753KMYyWxxxxxxxxx
9406203699300xxxxxxxxx
HJhTpq6zSzc8A9NeMpM4cvZ/wZL9paWtqGVF5Ja9b13+ASWOtjbUEuyS9AH4CYmMnWPQiuQAvevlMGxxxxxxxxx=

emailing label now...

Thanks!

[CanaryInTheMine]

Hi Canary - one blade por favor:

0754703166b569cf254b9140652b83c787549c2a79d5c28d0343bef79f786fb1
124jzM8sHhSit8LkV753KMYyWxxxxxxxxx
9406203699300xxxxxxxxx
HJhTpq6zSzc8A9NeMpM4cvZ/wZL9paWtqGVF5Ja9b13+ASWOtjbUEuyS9AH4CYmMnWPQiuQAvevlMGxxxxxxxxx=

emailing label now...

Thanks!

shipping...

[soy]

Hi Canary,

My Blade had been running 4 days shy of three months then started acting up.

It was only giving me double digits "accepted" as viewed on the proxy for a few seconds after powering up before hashrate dropped to zero and it started rebooting.  I changed power supplies.  I've reconfigured the routing a number of times and my other miners are running okay so the router shouldn't be the problem.

Then the ASIC chip display changed from all "O"'s to all "x"'s.  I've reset to factory defaults repeatedly, the new config showing 192.168.1.2,btcguild.com, but still all "'x"'s.  Reconfiguring to my proxy's I still see no indication of requesting work.  The web interface works fine.

I note that soon after getting the Blade 3 months ago I soldered a tantalum capacitor between the + & - pins at the power plug.  That is fine.

I measure 11.8vdc in and 1.04volts on the copper pads mid board.

I would almost guess it's the PIC acting  up.

Any suggestions?

Thanks.

soy

[ryanb]

mine keeps declaring sick and i have to unplug it and plug it back and restart bfgminer

it runs for few hours and claims sick again

maybe i should get a backplane

how much a backplane and i would probably get 3 more blades if you can give me a price on them with the backplane

i purchased like 50 usb eruptors when they were 0.55 each lol i am still in pain

so take care of me please

[Dogvomit]

1 Hub

Date: 12/5/2013 21:17
To: CanaryInTheMine - Hub 1GGFSxxncmXdP9tUSPNPAPi4timLahH191
Debit: -0.25 BTC
Net amount: -0.25 BTC
Transaction ID: 30600110ace5de1e380e552219023f94ac42e7009bbf253a6e9510df4f443bed

[aznatama]

I measure 11.8vdc in and 1.04volts on the copper pads mid board.

Any suggestions?

Thanks.

soy

Might want to give it a stable 12v... the backpane PSU provides 12.7v
If your power wires are getting hot, you're putting too much load through the power wires.  Use more wires.  Each 18ga wire is only rated for 2.3a worth of power transmission.  That's only about 27w of power.  you'll need 4 power lines if you're using 18ga wiring high quality pcie cables ise this, molex may have 20ga wiring which is only rated for about half)

[soy]

I measure 11.8vdc in and 1.04volts on the copper pads mid board.

Any suggestions?

Thanks.

soy

Might want to give it a stable 12v... the backpane PSU provides 12.7v
If your power wires are getting hot, you're putting too much load through the power wires.  Use more wires.  Each 18ga wire is only rated for 2.3a worth of power transmission.  That's only about 27w of power.  you'll need 4 power lines if you're using 18ga wiring high quality pcie cables ise this, molex may have 20ga wiring which is only rated for about half)

Okay, will up the voltage to 12.7V.  I had been running fine on 11.8V.  Would make less sense to raise the voltage given the board failed because we had an exceptionally warm winter's day here in Georgia and the room went up to 76°F after weeks at low 60°'s and that even with switching supplies/buck converters, the greater the voltage difference the more power lost at the supply.  But I will give it a try.   

[CanaryInTheMine]

Hi Canary,

My Blade had been running 4 days shy of three months then started acting up.

It was only giving me double digits "accepted" as viewed on the proxy for a few seconds after powering up before hashrate dropped to zero and it started rebooting.  I changed power supplies.  I've reconfigured the routing a number of times and my other miners are running okay so the router shouldn't be the problem.

Then the ASIC chip display changed from all "O"'s to all "x"'s.  I've reset to factory defaults repeatedly, the new config showing 192.168.1.2,btcguild.com, but still all "'x"'s.  Reconfiguring to my proxy's I still see no indication of requesting work.  The web interface works fine.

I note that soon after getting the Blade 3 months ago I soldered a tantalum capacitor between the + & - pins at the power plug.  That is fine.

I measure 11.8vdc in and 1.04volts on the copper pads mid board.

I would almost guess it's the PIC acting  up.

Any suggestions?

Thanks.

soy

as far as I know, blade modifications void the warranty.  you'd need to contact here: https://bitcointalk.org/index.php?topic=270573.0 to see what can or can not be done.  I do not have instructions to replace modified blades.

[soy]

No joy.  Here it is at 12.8V:

Total MHS:   00000
Received:   0000000000
Accepted:   0000000000
Per Minute:   000.00
Efficiency:   000.00%
Up Time:   0d,00h,00m,51s

Current Server: 192.168.1.4:8332
Chip: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
--------------------

I switch the server:

Total MHS:   00000
Received:   0000000000
Accepted:   0000000000
Per Minute:   000.00
Efficiency:   000.00%
Up Time:   0d,00h,02m,53s

Current Server: :19501
Chip: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

I Switch the server again:

Total MHS:   00000
Received:   0000000000
Accepted:   0000000000
Per Minute:   000.00
Efficiency:   000.00%
Up Time:   0d,00h,03m,26s

Current Server: 192.168.1.4:8332
Chip: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

I've seen others report the 19501 previously.

[CanaryInTheMine]

today's orders have been shipped.

[ryanb]

4 blades + backplane all paid and label has been emailed

5d2f49250e04b6fe1f326144bc5962de736cfb456bb41a305a2a4a8e01022540


Thanks

[CanaryInTheMine]

dropping off shipments. Thank you!

[sbfree]

canary, please reserve at least 2 blades and 2 backplanes(if possible on these). I have already PM'd you, and will send btc later today, thanks, sbfree.

[CanaryInTheMine]

canary, please reserve at least 2 blades and 2 backplanes(if possible on these). I have already PM'd you, and will send btc later today, thanks, sbfree.

PMed

[CanaryInTheMine]

orders up through today are being packed and will be dropped off shortly. thanks!