Abraxas601
Newbie
Offline
Activity: 47
Merit: 0
|
|
December 04, 2013, 12:08:15 AM |
|
Two Blades
5f247351a6923f31eb1424721f8035a00da876ed598e8209c3de351e0b2c11c2
|
|
|
|
|
|
Every time a block is mined, a certain amount of BTC (called the
subsidy) is created out of thin air and given to the miner. The
subsidy halves every four years and will reach 0 in about 130 years.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
CanaryInTheMine (OP)
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
December 04, 2013, 06:13:58 PM |
|
Two Blades
5f247351a6923f31eb1424721f8035a00da876ed598e8209c3de351e0b2c11c2
shipped. thanks!
|
|
|
|
CanaryInTheMine (OP)
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
December 04, 2013, 06:28:10 PM |
|
I see the backplane comes with 10 or more but will you sell them individually?
they are reserved for orders of 10 atm. if I happen to sell alot of individual blades and a few backplanes become "freed up" then I post their availability. I have some backplanes that are now freed up.
|
|
|
|
sebdude420
|
|
December 05, 2013, 12:26:47 AM |
|
I have done a lot of orders lately, can you save me one of those "freed" up backplanes?
|
OG Bitcoin Miner turned Proof of Stake Validator. Maxed out Raspberry Pi 4 8GB at 120$ a Day Revenue with ~15K XTZ Bonds in Summer of 2021. Looking at Proof of Stake systems all across the crypto ecosystem to expand operations.
|
|
|
artbatista
|
|
December 05, 2013, 02:13:09 AM |
|
Yes, I still have blades. Have received several PMs asking about them. Thanks!
These are v2 blades? Art
|
|
|
|
twib2
Sr. Member
Offline
Activity: 280
Merit: 250
Helperizer
|
|
December 05, 2013, 04:20:09 AM |
|
Hi Canary - one blade por favor:
0754703166b569cf254b9140652b83c787549c2a79d5c28d0343bef79f786fb1 124jzM8sHhSit8LkV753KMYyWxxxxxxxxx 9406203699300xxxxxxxxx HJhTpq6zSzc8A9NeMpM4cvZ/wZL9paWtqGVF5Ja9b13+ASWOtjbUEuyS9AH4CYmMnWPQiuQAvevlMGxxxxxxxxx=
emailing label now...
Thanks!
|
|
|
|
CanaryInTheMine (OP)
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
December 05, 2013, 05:41:54 PM |
|
Hi Canary - one blade por favor:
0754703166b569cf254b9140652b83c787549c2a79d5c28d0343bef79f786fb1 124jzM8sHhSit8LkV753KMYyWxxxxxxxxx 9406203699300xxxxxxxxx HJhTpq6zSzc8A9NeMpM4cvZ/wZL9paWtqGVF5Ja9b13+ASWOtjbUEuyS9AH4CYmMnWPQiuQAvevlMGxxxxxxxxx=
emailing label now...
Thanks!
shipping...
|
|
|
|
soy
Legendary
Offline
Activity: 1428
Merit: 1013
|
|
December 06, 2013, 01:13:50 AM |
|
Hi Canary,
My Blade had been running 4 days shy of three months then started acting up.
It was only giving me double digits "accepted" as viewed on the proxy for a few seconds after powering up before hashrate dropped to zero and it started rebooting. I changed power supplies. I've reconfigured the routing a number of times and my other miners are running okay so the router shouldn't be the problem.
Then the ASIC chip display changed from all "O"'s to all "x"'s. I've reset to factory defaults repeatedly, the new config showing 192.168.1.2,btcguild.com, but still all "'x"'s. Reconfiguring to my proxy's I still see no indication of requesting work. The web interface works fine.
I note that soon after getting the Blade 3 months ago I soldered a tantalum capacitor between the + & - pins at the power plug. That is fine.
I measure 11.8vdc in and 1.04volts on the copper pads mid board.
I would almost guess it's the PIC acting up.
Any suggestions?
Thanks.
soy
|
|
|
|
ryanb
Legendary
Offline
Activity: 1148
Merit: 1000
|
|
December 06, 2013, 01:20:24 AM |
|
mine keeps declaring sick and i have to unplug it and plug it back and restart bfgminer it runs for few hours and claims sick again maybe i should get a backplane how much a backplane and i would probably get 3 more blades if you can give me a price on them with the backplane i purchased like 50 usb eruptors when they were 0.55 each lol i am still in pain so take care of me please
|
|
|
|
Dogvomit
Newbie
Offline
Activity: 4
Merit: 0
|
|
December 06, 2013, 03:19:10 AM |
|
1 Hub
Date: 12/5/2013 21:17 To: CanaryInTheMine - Hub 1GGFSxxncmXdP9tUSPNPAPi4timLahH191 Debit: -0.25 BTC Net amount: -0.25 BTC Transaction ID: 30600110ace5de1e380e552219023f94ac42e7009bbf253a6e9510df4f443bed
|
|
|
|
aznatama
|
|
December 06, 2013, 06:42:10 PM |
|
I measure 11.8vdc in and 1.04volts on the copper pads mid board.
Any suggestions?
Thanks.
soy
Might want to give it a stable 12v... the backpane PSU provides 12.7v If your power wires are getting hot, you're putting too much load through the power wires. Use more wires. Each 18ga wire is only rated for 2.3a worth of power transmission. That's only about 27w of power. you'll need 4 power lines if you're using 18ga wiring high quality pcie cables ise this, molex may have 20ga wiring which is only rated for about half)
|
|
|
|
soy
Legendary
Offline
Activity: 1428
Merit: 1013
|
|
December 06, 2013, 10:07:56 PM |
|
I measure 11.8vdc in and 1.04volts on the copper pads mid board.
Any suggestions?
Thanks.
soy
Might want to give it a stable 12v... the backpane PSU provides 12.7v If your power wires are getting hot, you're putting too much load through the power wires. Use more wires. Each 18ga wire is only rated for 2.3a worth of power transmission. That's only about 27w of power. you'll need 4 power lines if you're using 18ga wiring high quality pcie cables ise this, molex may have 20ga wiring which is only rated for about half) Okay, will up the voltage to 12.7V. I had been running fine on 11.8V. Would make less sense to raise the voltage given the board failed because we had an exceptionally warm winter's day here in Georgia and the room went up to 76°F after weeks at low 60°'s and that even with switching supplies/buck converters, the greater the voltage difference the more power lost at the supply. But I will give it a try.
|
|
|
|
CanaryInTheMine (OP)
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
December 06, 2013, 10:16:26 PM |
|
Hi Canary,
My Blade had been running 4 days shy of three months then started acting up.
It was only giving me double digits "accepted" as viewed on the proxy for a few seconds after powering up before hashrate dropped to zero and it started rebooting. I changed power supplies. I've reconfigured the routing a number of times and my other miners are running okay so the router shouldn't be the problem.
Then the ASIC chip display changed from all "O"'s to all "x"'s. I've reset to factory defaults repeatedly, the new config showing 192.168.1.2,btcguild.com, but still all "'x"'s. Reconfiguring to my proxy's I still see no indication of requesting work. The web interface works fine.
I note that soon after getting the Blade 3 months ago I soldered a tantalum capacitor between the + & - pins at the power plug. That is fine.
I measure 11.8vdc in and 1.04volts on the copper pads mid board.
I would almost guess it's the PIC acting up.
Any suggestions?
Thanks.
soy
as far as I know, blade modifications void the warranty. you'd need to contact here: https://bitcointalk.org/index.php?topic=270573.0 to see what can or can not be done. I do not have instructions to replace modified blades.
|
|
|
|
soy
Legendary
Offline
Activity: 1428
Merit: 1013
|
|
December 06, 2013, 10:19:07 PM |
|
No joy. Here it is at 12.8V:
Total MHS: 00000 Received: 0000000000 Accepted: 0000000000 Per Minute: 000.00 Efficiency: 000.00% Up Time: 0d,00h,00m,51s
Current Server: 192.168.1.4:8332 Chip: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx --------------------
I switch the server:
Total MHS: 00000 Received: 0000000000 Accepted: 0000000000 Per Minute: 000.00 Efficiency: 000.00% Up Time: 0d,00h,02m,53s
Current Server: :19501 Chip: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
I Switch the server again:
Total MHS: 00000 Received: 0000000000 Accepted: 0000000000 Per Minute: 000.00 Efficiency: 000.00% Up Time: 0d,00h,03m,26s
Current Server: 192.168.1.4:8332 Chip: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
I've seen others report the 19501 previously.
|
|
|
|
CanaryInTheMine (OP)
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
December 06, 2013, 11:41:23 PM |
|
today's orders have been shipped.
|
|
|
|
ryanb
Legendary
Offline
Activity: 1148
Merit: 1000
|
|
December 07, 2013, 07:02:50 AM |
|
4 blades + backplane all paid and label has been emailed
5d2f49250e04b6fe1f326144bc5962de736cfb456bb41a305a2a4a8e01022540
Thanks
|
|
|
|
CanaryInTheMine (OP)
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
December 07, 2013, 06:39:31 PM |
|
dropping off shipments. Thank you!
|
|
|
|
sbfree
|
|
December 08, 2013, 02:21:19 PM |
|
canary, please reserve at least 2 blades and 2 backplanes(if possible on these). I have already PM'd you, and will send btc later today, thanks, sbfree.
|
|
|
|
CanaryInTheMine (OP)
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
December 09, 2013, 05:13:16 AM |
|
canary, please reserve at least 2 blades and 2 backplanes(if possible on these). I have already PM'd you, and will send btc later today, thanks, sbfree.
PMed
|
|
|
|
CanaryInTheMine (OP)
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
December 09, 2013, 05:25:10 PM |
|
orders up through today are being packed and will be dropped off shortly. thanks!
|
|
|
|
|