30gh/s cube Help

[voodoyou]

Ok, so I just got my 30gh/s cube and dont want to mess it up. Having problems finding any write ups in regards to starting this thing up. what all do I need? Power supply, cables.... what is the plug it comes with, with a jumper wire for?

[1714909720]

1714909720

[Skaterdiejosh]

https://bitcointalk.org/?topic=205369.0

That's about the best you will find !! Good luck hope it helps

[ScripterRon]

This one is dedicated to the BE Cube: https://bitcointalk.org/index.php?topic=352658

That should get you going.  The plug with the jumper tells your power supply to turn on - much better than the old paper clip trick.  There are a number of power supplies you can use.  I'm using the XFX Pro 550W which is more than sufficient for a single cube.  I'm using BFGMiner for the stratum proxy because I also have BE USB devices and so already have BFGMiner running.

[Skaterdiejosh]

So you have to use 1 power supply per cube ?? Im thinking about getting 2 cubes just to run till febuary Pre-orders arrive . If i get a 600 watt power supply will it run 2 of them u think ? Thx

[xzempt]

So you have to use 1 power supply per cube ?? Im thinking about getting 2 cubes just to run till febuary Pre-orders arrive . If i get a 600 watt power supply will it run 2 of them u think ? Thx

a 600w *should run 2  if you use the low clock setting....    you dont want to run the psu at max watts constantly....


id suggest a 750w or 800w  to run 2 in overclock mode....

[Skaterdiejosh]

I think your right about 800 watts would be perfect Expecially since at over clock they run 280 watts allmost 300 so be on the safe side

[voodoyou]

Im getting a power supply tonight, Ill keep you all posted thanks for the great links!

[voodoyou]

ok so there are two 6 pin power connection spots do I need to power both or just one with ample psu?

[xzempt]

i have both of mine plugged in

[voodoyou]

ok, so I got another psu with the correct number of 6pin connectors and the two green and the red status light comes on, when I plug in the ether cord it flashes green and the yellow light comes on and stays on.  hope that all good, now I put in the recomended address of 192.168.1.254:8000 get a time out response, I look at my ipconfig I get
subnet mask........ 255.255.255.0
defalut gateway.....192.168.2.1

err I'm confused as to what the address should look like?
I tried 192.168.2.254:8000 with no avail either

[sidehack]

Change your computer's IP to 192.168.1.whatever and try again. You'll need to change the Cube's IP to 192.168.2.whatever and then put your computer's IP back to its previous settings. After that you should have no trouble accessing the Cube's config page whenever you want.

[voodoyou]

ok great that worked took me a bit to figure it all out but I can easily access the config page!

downloaded mining proxy tried entering a pool address as shown as a bat file but no luck, I get

unhandled error in deferred:
unhandled error
traceback <most recent call last>:
failure: stratum.custom_exceptions.transportExcption: SocketTransportClinetfactory connection timed out
2013-12-17 15:53:13,641 ERROR proxy client_service.on_timeout # connections to up stream pool timed out

[voodoyou]

is there a way to use bfgminer I have block erupters running on that, is that a problem?

[sidehack]

What's your batch file contents?

[voodoyou]

C:\Users\riddick\Desktop\mining proxy\mining_proxy.exe -o stratum+tcp://nl1.ghash.io:3334

but it just opens and closes, when I put the same info in at command it gives the previously stated response,

[sidehack]

In a batch file:

start C:\Users\riddick\Desktop\mining proxy\mining_proxy.exe -o nl1.ghash.io -p 3334

[voodoyou]

time stamp    INFO proxy clien_service.handle_event #new job 23761eb for prevhash ec56aa61, clean_jobs=false

repeats with new job code

[sidehack]

Your cube config stuff needs to match the computer's IP information.

IP   -> unique IP for your hardware
Mask   -> probably 255.255.255.0
Gateway   -> 192.168.2.1
WEB Port   -> 8000
Primary DNS   -> 192.168.2.1
Secondary DNS   -> eh, whatever
Pool ports   -> 8332,8332
Pool addresses   -> your computer's IP
Miners user:pas -> worker credentials

[voodoyou]

it looks right to me.... unique ip would be ipv4 address correct

[dbzenhosting]

My Cube running at High mode uses 385Watts.
If you want to run 2 cubes on high mode you should at least get a 800W PSU or better.