voodoyou (OP)
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 16, 2013, 05:38:13 PM |
|
Ok, so I just got my 30gh/s cube and dont want to mess it up. Having problems finding any write ups in regards to starting this thing up. what all do I need? Power supply, cables.... what is the plug it comes with, with a jumper wire for?
|
|
|
|
|
ScripterRon
|
|
December 16, 2013, 07:41:28 PM |
|
This one is dedicated to the BE Cube: https://bitcointalk.org/index.php?topic=352658That should get you going. The plug with the jumper tells your power supply to turn on - much better than the old paper clip trick. There are a number of power supplies you can use. I'm using the XFX Pro 550W which is more than sufficient for a single cube. I'm using BFGMiner for the stratum proxy because I also have BE USB devices and so already have BFGMiner running.
|
|
|
|
Skaterdiejosh
|
|
December 16, 2013, 08:00:32 PM |
|
So you have to use 1 power supply per cube ?? Im thinking about getting 2 cubes just to run till febuary Pre-orders arrive . If i get a 600 watt power supply will it run 2 of them u think ? Thx
|
|
|
|
xzempt
|
|
December 16, 2013, 08:12:56 PM |
|
So you have to use 1 power supply per cube ?? Im thinking about getting 2 cubes just to run till febuary Pre-orders arrive . If i get a 600 watt power supply will it run 2 of them u think ? Thx a 600w *should run 2 if you use the low clock setting.... you dont want to run the psu at max watts constantly.... id suggest a 750w or 800w to run 2 in overclock mode....
|
|
|
|
Skaterdiejosh
|
|
December 16, 2013, 08:33:46 PM |
|
I think your right about 800 watts would be perfect Expecially since at over clock they run 280 watts allmost 300 so be on the safe side
|
|
|
|
voodoyou (OP)
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 16, 2013, 09:49:52 PM |
|
Im getting a power supply tonight, Ill keep you all posted thanks for the great links!
|
|
|
|
voodoyou (OP)
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 17, 2013, 03:09:06 AM |
|
ok so there are two 6 pin power connection spots do I need to power both or just one with ample psu?
|
|
|
|
xzempt
|
|
December 17, 2013, 03:10:28 AM |
|
i have both of mine plugged in
|
|
|
|
voodoyou (OP)
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 17, 2013, 07:38:21 PM |
|
ok, so I got another psu with the correct number of 6pin connectors and the two green and the red status light comes on, when I plug in the ether cord it flashes green and the yellow light comes on and stays on. hope that all good, now I put in the recomended address of 192.168.1.254:8000 get a time out response, I look at my ipconfig I get subnet mask........ 255.255.255.0 defalut gateway.....192.168.2.1
err I'm confused as to what the address should look like? I tried 192.168.2.254:8000 with no avail either
|
|
|
|
sidehack
Legendary
Online
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
|
December 17, 2013, 08:00:52 PM |
|
Change your computer's IP to 192.168.1.whatever and try again. You'll need to change the Cube's IP to 192.168.2.whatever and then put your computer's IP back to its previous settings. After that you should have no trouble accessing the Cube's config page whenever you want.
|
|
|
|
voodoyou (OP)
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 17, 2013, 09:56:13 PM |
|
ok great that worked took me a bit to figure it all out but I can easily access the config page!
downloaded mining proxy tried entering a pool address as shown as a bat file but no luck, I get
unhandled error in deferred: unhandled error traceback <most recent call last>: failure: stratum.custom_exceptions.transportExcption: SocketTransportClinetfactory connection timed out 2013-12-17 15:53:13,641 ERROR proxy client_service.on_timeout # connections to up stream pool timed out
|
|
|
|
voodoyou (OP)
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 17, 2013, 10:53:52 PM |
|
is there a way to use bfgminer I have block erupters running on that, is that a problem?
|
|
|
|
sidehack
Legendary
Online
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
|
December 17, 2013, 11:38:39 PM |
|
What's your batch file contents?
|
|
|
|
voodoyou (OP)
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 17, 2013, 11:53:33 PM |
|
C:\Users\riddick\Desktop\mining proxy\mining_proxy.exe -o stratum+tcp://nl1.ghash.io:3334
but it just opens and closes, when I put the same info in at command it gives the previously stated response,
|
|
|
|
sidehack
Legendary
Online
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
|
December 18, 2013, 12:14:56 AM |
|
In a batch file:
start C:\Users\riddick\Desktop\mining proxy\mining_proxy.exe -o nl1.ghash.io -p 3334
|
|
|
|
voodoyou (OP)
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 18, 2013, 12:30:41 AM |
|
time stamp INFO proxy clien_service.handle_event #new job 23761eb for prevhash ec56aa61, clean_jobs=false
repeats with new job code
|
|
|
|
sidehack
Legendary
Online
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
|
December 18, 2013, 12:48:38 AM |
|
Your cube config stuff needs to match the computer's IP information.
IP -> unique IP for your hardware Mask -> probably 255.255.255.0 Gateway -> 192.168.2.1 WEB Port -> 8000 Primary DNS -> 192.168.2.1 Secondary DNS -> eh, whatever Pool ports -> 8332,8332 Pool addresses -> your computer's IP Miners user:pas -> worker credentials
|
|
|
|
voodoyou (OP)
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 18, 2013, 01:10:06 AM |
|
it looks right to me.... unique ip would be ipv4 address correct
|
|
|
|
dbzenhosting
|
|
December 18, 2013, 01:28:05 AM |
|
My Cube running at High mode uses 385Watts. If you want to run 2 cubes on high mode you should at least get a 800W PSU or better.
|
|
|
|
|