Exploit Antminer S9 and T9+ Firmware ASICBOOST original moded , FREE RELEASE !

[thierry4wd]

Where's the source code?

Hi, the proof is there, you criticized me without even reading me! it's too bad ...

In my first post I say that I do not have the source code for the simple reason that I use a BMMINER of origin! no change !!! therefore, you must ask for the sources at bitmain;)

The function of my "firmware" or rather "mod" is that I apel the function ask by another way ... at least in a few words ...

And as Taserz said I'm not a scammer, I help as I stink here!

[1714105369]

1714105369

[taserz]

There is a way to patch BMMINER specifically to set fixed frequency and asicboost. Not sure how you can do voltage control increments since it's hardcoded per frequency range.

[danbel79]

I am a user of brains, currently and I confess that Bitmain is disgusting, currently, in the last S9 they sold from the J Series, they removed a chip, to block the writing of the Nand. Not only did they update the 2019 firmware, but they removed hardware to disable writing on the control board. They sell miners set at high voltages, when they can be more efficient, either by frequency or by voltage. It was the case of miners 12.93 Mhz, set over 9 volts and frequency of 600 Mhz (1450W to 1600 W). I admire the trajectory of kano, but I also congratulate the courage of thierry4wd. I think we shouldn't argue, we are on the same Team!

[thierry4wd]

EDITED !

Up ! FREE FOR ALL !!!

ENJOY !!!

[kasner]

Hi !
Download links are not working, Can someone give valid download link ?
TNX.

[Coinerstone]

Thierry4wd, would you reupload, please? Download expired. Much appreciated.

[thierry4wd]

I see a lot of downloads but no comments, I am disappointed!

[Coinerstone]

I see a lot of downloads but no comments, I am disappointed!

When I click your download link in the 1st post, it says download expired on 09/01/2020.

[thierry4wd]

UPDATED !

Please send your comment after test

[Coinerstone]

Here is the result of my testing. Your firmware works. However, I am getting lower hashrates compared to current firmware with a dev fee! I am downvolting the S9 for power saving.

On the current firmware I am using I have stable 9,4Th with the 720Watts drawn on a meter. Settings 445Mhz/8V Dev fee is 1,8% so I am getting effectively 9,2Th for me. This means 12,77 Gh/W efficiency.

I tested you firmware.It is fairly stable (one to two-hours each settings) at the following hashrates. Always 8V:
445Mhz 8.5Th with 686W, efficiency 12.3Gh/W
425Mhz 8.0Th with 644W, efficiency 12.42 Gh/W
375Mhz 7.7Th with 611W, efficiency 12.6Gh/W
350Mhz 7,5Th with 588W, efficiency 12.75Gh/W

Only at 350Mhz I am getting roughly the same efficiency, but I then I get 7.5Th, not 9.2Th... They did something in the custom dev-fee firmware that allows higher hashrates.

Nevertheless, your firmware is genuine Keep up the good work. I wonder how it would be with the newest bitmain firmware, but it is not possible to downwolt it without recompiling the "kernel module" C++ code - I am rookie so I do not remember the proper names.

[thierry4wd]

thanks for yours tests and comment

But is not my firmware, is just my "mod" for unlock feature on original firmware

With pleasure !

[radd66]

Hi!

Download Links not working, File not found!

Could you re upload !

[MoparMiningLLC]

anyone have proof of finding a block once they switch over to this modified FW?

that is my question with any of these firmwares once they are released.

[thierry4wd]

anyone have proof of finding a block once they switch over to this modified FW?

that is my question with any of these firmwares once they are released.

I don't know why my mod not find bloc ?

I have say what, just install original firmware (for S9J), and after, install my mod, so, my mod containe only new "minerconfig" page, and new booting file, for force miner to start at frequency fixed and take new config on config file (freq / fan / voltage) ...

In absolu , is ORIGINAL firmware ! not modified ! my mod is just a proof to bitmain say error on THIS firmware, bmminer is all coded to take all config !

 

[HagssFIN]

@OP
Have you tested this in the test net?

[thierry4wd]

Yes, my mod run good arround more than 1 years, but, no find BTC bloc, is possible to find only one bloc BTC on 1 years ? i don't know lol , but i find many bloc on shitcoin ... in absolut, is the OEM firmware ! i say and re say !!! 


Link updated

[bouffemonshort]

Hello, there is a link for the firmware of the T9 +? I only see for the S9
thx

[thierry4wd]

Updated i built T9+ mod with bmminer opencore at 890mv(put in 2019 version), is very good for not over charge psu at start up ... by this, allowed to run T9+ at 725mhz by APW3

Please leave your result after testing

[sanhwy]

download link : S9 / S9I / S9J
- Original firmware for S9J (compatible with S9 / S9I / S9J) : https://easyupload.io/b2xgv5
- My patch (need flash S9J firmware before) : https://easyupload.io/5khk9p

link not working, can you fix ?

[connectCORRECT]

I'm looking for a modified firmware for S9 Hydro (4x Hashboard) with AsicBoost. Preferably something similar to the modified fw for S9, which allows chip tuning.
But I don't see anything on the S9 Hydro. Theoretically, the fw for S9 Hydro could be derived from the firmware for T9 + which has similar connectors and I tried it. It's OK, but I can only use 3 Hashboards.
Thank you for your reply or for the link, recommendation ...