chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
October 01, 2019, 11:32:54 PM |
|
Updated mod images have been sent to purchasers please check your email
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
jano20
Newbie
Offline
Activity: 2
Merit: 0
|
|
October 07, 2019, 03:16:10 PM |
|
FusionSilicon X1 software needed 4.11
|
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
October 07, 2019, 04:03:05 PM |
|
FusionSilicon X1 software needed 4.11
Pm'd you .....
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
mattaero
Jr. Member
Offline
Activity: 178
Merit: 2
|
|
October 11, 2019, 01:09:55 PM |
|
Have you been able, or even looked into, what Bitmain did to limit speeds on the Z11e and Z11j? I have had all three, and from what I can tell, there are the same number of chips, boards, and power, but they somehow throttle the Z11J and Z11e. I have used eFudds firmware on them before and I can increase the frequency and squeeze a bit more out of them, but only at their throttled speeds. Ideally, I would like to turn the Z11e into a Z11.
I am not someone who can really dig into this, but if it is software limited (Or on the chip somehow?) I would certainly pay to be able to turn a 75k sol/s Z1e into a 135k Z11...
Thoughts?
|
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
October 11, 2019, 06:21:46 PM |
|
Have you been able, or even looked into, what Bitmain did to limit speeds on the Z11e and Z11j? I have had all three, and from what I can tell, there are the same number of chips, boards, and power, but they somehow throttle the Z11J and Z11e. I have used eFudds firmware on them before and I can increase the frequency and squeeze a bit more out of them, but only at their throttled speeds. Ideally, I would like to turn the Z11e into a Z11.
I am not someone who can really dig into this, but if it is software limited (Or on the chip somehow?) I would certainly pay to be able to turn a 75k sol/s Z1e into a 135k Z11...
Thoughts?
sent you a pm
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
October 15, 2019, 07:16:07 AM Last edit: October 16, 2019, 07:07:32 AM by chipless |
|
S17 and S17 Pro update....
The S17 is completed but as of now there is a deal in the progress and public release has been put on hold pending the outcome of a pending deal. If the deal does not go thru within the next 72 hours I will consider a public release for a 1 license per miner with discounts for multiple miners.
Update..... The deal went thru and there will be no release of this S17 version of firmware. Check back for future updates on the S17
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
Litecoiners
Newbie
Offline
Activity: 30
Merit: 0
|
|
October 17, 2019, 11:19:35 AM |
|
Hello.Do you have software also for Dayun Z1 Pro ?
|
|
|
|
Kalyst69
Jr. Member
Offline
Activity: 147
Merit: 1
|
|
October 17, 2019, 12:47:06 PM |
|
Hello,
Any news about a mod firmware for S9k ?
Thanks
|
Host your ASICs in Siberia for $0.07/KW all inclusive. Contact me for information.
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
October 17, 2019, 02:42:12 PM |
|
Hello.Do you have software also for Dayun Z1 Pro ?
Not as of yet soon.....
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
October 17, 2019, 02:42:59 PM |
|
Hello,
Any news about a mod firmware for S9k ?
Thanks
I have been working on the S9k this week and will keep all updated of the progress
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
Kalyst69
Jr. Member
Offline
Activity: 147
Merit: 1
|
|
October 17, 2019, 10:47:42 PM |
|
I have been working on the S9k this week and will keep all updated of the progress
If you need a S9k for testing purpose, we can arrange that. We have 400 S9k in a container that are waiting your software
|
Host your ASICs in Siberia for $0.07/KW all inclusive. Contact me for information.
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
October 17, 2019, 11:29:56 PM |
|
I have been working on the S9k this week and will keep all updated of the progress
If you need a S9k for testing purpose, we can arrange that. We have 400 S9k in a container that are waiting your software Thank you for the offer. As of yet I do not have one for testing on so it will go slower pm me and we can discuss a loaner possibly
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
October 20, 2019, 08:18:01 AM |
|
may i ask you how much it would be possible in case of overclocking s9k 14 th?
I am still testing the s9k stuff so I dont have a full answer yet. All I can say is more then factory at this time.
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
balla69
Newbie
Offline
Activity: 75
Merit: 0
|
|
October 21, 2019, 02:31:57 PM |
|
if you interest, i've request at bitmain the image for reset from SD card. I've tested the braiins SD image but the miner don't see the image...
|
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
October 21, 2019, 09:58:23 PM |
|
if you interest, i've request at bitmain the image for reset from SD card. I've tested the braiins SD image but the miner don't see the image...
I already have SD images for the miners. Bitmain wont make them for many newer models. Already tried for months with them so I made my own for many of the different model miners.
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
efudd
Member
Offline
Activity: 504
Merit: 51
|
|
November 01, 2019, 10:30:20 PM |
|
FYI, I'll be releasing a dev-fee free, $0 cost, no callbacks, no licenses, blahblah, completely unencumbered overclock for all of these SHA-256 "soon".
So.. be patient and don't pay $100/miner or $150/miner, etc. when I'll charge $0/miner.
-j
|
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
November 02, 2019, 07:19:07 AM |
|
FYI, I'll be releasing a dev-fee free, $0 cost, no callbacks, no licenses, blahblah, completely unencumbered overclock for all of these SHA-256 "soon".
So.. be patient and don't pay $100/miner or $150/miner, etc. when I'll charge $0/miner.
-j
Well goody... We will have some more firmware from you that will have 1 or 2 releases then no more updates because you got pissed off. All you are gonna do is screw yourself with your ego. You think all should depend on yourhineass efudd. I forgot to thank you for all the private clients who were tired of your bs lies about what can and cant be done and why their miners were going into dev mode always with a license. Either way good luck Let add why dont you unlock your thread so I can post there or unblock me from your discord? Hmm.... The epuff power trip I guess
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
November 13, 2019, 06:49:27 AM |
|
Important Update.... Free Mods Check out the my other Discord channels I have for 100% free mods and unfinished mod files. These units I do not have time to work on now and there is no reason others can work with or on them as time is running out on everyones ROI. I hope you enjoy and remember I do take donations
Some models.... FS-X1, FS-X2, Antminer X3, InnoSilicon A9 Zmaster!!! All for free to use or modify.
Discord.... https://discord.gg/8cgtBcE
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
chipless (OP)
Jr. Member
Offline
Activity: 559
Merit: 4
|
|
November 15, 2019, 04:51:25 AM Last edit: November 18, 2019, 05:14:21 AM by chipless |
|
T17 modded firmware is ready. The current details are voltage and freq control. The price of the mod is $100 in zec or btc per miner. The speeds are as high as 60th+ with power varying from 2600-over 4000 watts depending on your settings. I don't want to hear about ROI etc because the firmware is for the life of the miner and the ROI can be fast or it can be spread out. If you are using dev fee and paying a percentage that could be going towards the equipment ROI then my firmware is for you. Put that 3% back in your pocket. Contact me for purchase info.
975m@18.30v 3476watts current now 56075.37 avg after 3 hrs 56295.01Features... Ignores dead chips safe for immersion will ignore 0 rpm fan errors max temp shutdown control Frequency control Voltage Control No DevFee license only Fan Control Sleep, Normal, Turbo Modes
|
Share your results with others on my Discord channel https://discord.gg/6t62apJ
|
|
|
favebook
|
|
November 15, 2019, 10:51:10 AM |
|
Features... Ignores dead chips safe for immersion will ignore 0 rpm fan errors max temp shutdown control Frequency control Voltage Control No DevFee license only Fan Control Sleep, Normal, Turbo Modes
"Ignores dead chips"? Does it mean if my miner(S17 Pro) finds 46 chips instead of 48 and shuts down that hashboard, this can be avoided via your firmware? Also, is this firmware available for S17/S17Pro/S17e?
|
|
|
|
|