T17/S17 malfunction: cases, solutions, remedies, RMA history

[mikeywith]

What kind of glue use the heatsinks of the S17 T17 hashboards?

The cheapest would be the black glue from China, it's available on both Aliexpress and Zuesbtc > https://www.zeusbtc.com/RepairDetails.asp?ID=86, keep in mind that this product can't be stored outside the fridge for more than 10 days, so check with the seller as well as the carrier, the second option which is a lot more expensive but probably has better quality and easier to get would be Arctic > https://www.amazon.com/Arctic-Silver-Premium-Adhesive-ASTA-7G/dp/B0087X7262.

wndsnb also mentioned using a different product somewhere which I can't find, I hope he would chime in and post the link

[1714943913]

1714943913

[1714943913]

1714943913

[1714943913]

1714943913

[wndsnb]

What kind of glue use the heatsinks of the S17 T17 hashboards?

At the factory, the heatsinks are soldered on using low-temperature melting point solder (~140 degC). This is what I use https://www.chipquik.com/store/product_info.php?products_id=470006.

The soldering only works if the copper plating is still on the top of the chip, and from my experience, most of the time heatsinks fall off it is caused when the plating delaminates. If that is the case, then the only options are to use a thermally conductive adhesive or to replace the chip.

[Pendrak]

Solder?? i see. thank you.

If the plating is still there what kind of solder you can use? lead or leaded?i guess have to add just a little for complete.

[RRZP028]

Hello, here I am after a break.

now I have encountered a problem that one capacitor that should pass a voltage of 0.7v does not give me any value. my question is whether to sell to replace with someone else from some other record or to do something else. The hash board is from T17e.

https://imgur.com/Gt9PdtL
https://imgur.com/gEsZ2Cb
https://imgur.com/TD6ZSAb

and I have another problem because when I'm on another hash board from the same machine it performs a voltage check on those capacitors, my test device started the hash board so now I don't know what to do with it because I just turned it off and didn't continue testing because other obligations.

[wndsnb]

The side of the capacitor that your probe is touching in the image is the ground side, so it would always measure 0V. The other side should be 0.8V.

The 1.8V and 0.8V flow through each chip to the next, in this image the signal travels A -> B -> C. The 0.8V enters the ASIC at A, and exits the chip at B.



To make sure the connection is being made through the new ASIC you put down, measure the resistance between these two points indicated in the following image. The resistance should be less than 1 ohm.

[RRZP028]

Dear Mr. wndsnb, can you tell me from which country, because I am from Europe, the state of Serbia, I am asking you so that I would know when you reply to our messages so that I can respond to you quickly and not just for a few hours.
I have no problem being next to the computer at any time of the day or night just to finally find a way to fix one hash board, also thanks for the tips so far.

[wndsnb]

Dear Mr. wndsnb, can you tell me from which country

I'm from east coast USA, but I can't promise quick responses.... I'm pretty busy these days. I respond when I can find time....

[Moeter81]

[...]

I just wanted to give you a status update.

After I sent my defective miner to Bitmain on October 29th, a replacement device was sent to me from Hong Kong today. That was fast!!! I hope the device works longer.

I have already bought the M30 + and M30 ++, they have been running without any problems so far and I am satisfied with them. From Bitmain, I will keep my distance first, have had too many defective devices (S17 +).

[RadekG2]

Haha, same at my side. I sent 5 dead S17 to Bitmain during October and now, more than half year later they sent me 1 working and two dead units. I'll repair them by myself.

[wndsnb]

My experience repairing these so far has shown that the faulty miners typically have multiple issues, and all the issues don't always present themselves. I run miners several days after a repair to make sure they are stable, and nearly 100% of the time they fail again, normally in different ways, within a few days. So not surprised to see a lot of reports of "repaired" miners arriving broken.

[Astra2000]

OMG, I have order and pay for a used S17+ from alibaba, I'm already scared what gonna append....

Any thoughts how to prevent the heat sinks from falling?
Any solutions for this problem?

Maybe laying the miner sideways instead upward? 

[mikeywith]

OMG, I have order and pay for a used S17+ from alibaba, I'm already scared what gonna append....

Buy first and then do your research, way to go, my friend.

Any thoughts how to prevent the heat sinks from falling?

Try to keep them cool that will help.

Maybe laying the miner sideways instead upward? 

some folks reported some tiny percentage of success by placing them horizontally, I'd say it's a fraction of an effect but well, why not? just make sure you place the chips up, the larger heatsink needs to face up.

[Astra2000]

yeh, I'm a mining newbie and I haven't though about the problems associate with the miners S17.

The turn off to buy the S19 was the price, they are selling for 15K and the S17 for 5k ... so for me was a no brainer LOL

maybe I sell it as soon I get them.

[robertpaulsen]

I have an issue with my T17, one just 1 hashboard. Sometimes i get 0 asic found sometimes it finds all 30. But in any case, I get the error for all temp sensors on the board. I think I've went through most of the posts here and it most likely resembles the issue I quoted below. As I could see, most likely its loose heatsink, but after my (inexperienced) inspection, none seems loose when tested with mild pressure. Can anyone point me to some diy fix (I have only solder, no heatgun) or just take it to the repair shop? Here are the logs:

When finding all asics:

Code:

2021-10-14 17:42:05 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2021-10-14 17:42:05 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2021-10-14 17:42:05 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2021-10-14 17:42:05 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-10-14 17:42:05 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2021-10-14 17:42:05 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2021-10-14 17:42:05 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2021-10-14 17:42:05 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2021-10-14 17:42:05 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-10-14 17:42:05 thread.c:789:create_read_nonce_reg_thread: create thread
2021-10-14 17:42:11 driver-btm-api.c:1067:init_miner_version: miner ID : 803c95042b104814
2021-10-14 17:42:11 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2021-10-14 17:42:13 eeprom.c:431:check_pattern_test_level: L1 board
2021-10-14 17:42:15 eeprom.c:431:check_pattern_test_level: L1 board
2021-10-14 17:42:16 eeprom.c:431:check_pattern_test_level: L1 board
2021-10-14 17:42:16 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2021-10-14 17:42:16 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2021-10-14 17:42:16 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2021-10-14 17:42:16 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2021-10-14 17:42:16 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2021-10-14 17:42:16 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2021-10-14 17:42:16 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2021-10-14 17:42:16 driver-btm-api.c:644:_set_project_type: project:2
2021-10-14 17:42:17 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2021-10-14 17:42:17 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-10-14 17:42:17 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-10-14 17:42:17 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-10-14 17:42:17 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-10-14 17:42:17 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-10-14 17:42:17 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-10-14 17:42:18 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2021-10-14 17:42:19 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-10-14 17:42:23 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2021-10-14 17:42:24 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-10-14 17:42:28 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2021-10-14 17:42:30 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-10-14 17:42:33 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2021-10-14 17:42:33 thread.c:784:create_pic_heart_beat_thread: create thread
2021-10-14 17:42:33 power_api.c:55:power_init: power init ... 
2021-10-14 17:42:33 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-10-14 17:43:05 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2021-10-14 17:43:11 power_api.c:124:check_voltage_multi: retry time: 0
2021-10-14 17:43:13 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.677236 
2021-10-14 17:43:14 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.120039 
2021-10-14 17:43:16 power_api.c:86:get_average_voltage: chain[2], voltage is: 16.917978 
2021-10-14 17:43:16 power_api.c:97:get_average_voltage: aveage voltage is: 17.238418 
2021-10-14 17:43:16 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2021-10-14 17:43:16 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-10-14 17:43:16 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2021-10-14 17:43:16 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2021-10-14 17:43:16 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-10-14 17:43:28 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2021-10-14 17:43:38 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2021-10-14 17:43:48 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2021-10-14 17:43:51 driver-btm-api.c:348:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2021-10-14 17:43:51 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2021-10-14 17:43:52 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2021-10-14 17:43:52 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2021-10-14 17:43:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2021-10-14 17:43:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2021-10-14 17:43:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2021-10-14 17:43:52 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2021-10-14 17:43:52 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2021-10-14 17:43:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-10-14 17:43:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2021-10-14 17:43:53 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2021-10-14 17:43:53 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-10-14 17:43:53 voltage[0] = 1690
2021-10-14 17:43:53 voltage[1] = 1690
2021-10-14 17:43:53 voltage[2] = 1690
2021-10-14 17:43:53 power_api.c:140:set_working_voltage: working_voltage = 16.900000
2021-10-14 17:43:54 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2021-10-14 17:43:55 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2021-10-14 17:43:57 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2021-10-14 17:43:57 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2021-10-14 17:43:57 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2021-10-14 17:43:57 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2021-10-14 17:43:57 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2021-10-14 17:43:59 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 21
2021-10-14 17:43:59 thread.c:804:create_check_miner_status_thread: create thread
2021-10-14 17:43:59 thread.c:794:create_set_miner_status_thread: create thread
2021-10-14 17:43:59 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2021-10-14 17:43:59 thread.c:779:create_temperature_monitor_thread: create thread
2021-10-14 17:43:59 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2021-10-14 17:43:59 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.80 ...
2021-10-14 17:44:33 power_api.c:124:check_voltage_multi: retry time: 0
2021-10-14 17:44:35 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.781328 
2021-10-14 17:44:37 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.769082 
2021-10-14 17:44:39 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.744590 
2021-10-14 17:44:39 power_api.c:97:get_average_voltage: aveage voltage is: 17.765000 
2021-10-14 17:44:39 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2021-10-14 17:44:39 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2021-10-14 17:44:39 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2021-10-14 17:44:39 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2021-10-14 17:44:39 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2021-10-14 17:44:39 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2021-10-14 17:44:39 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2021-10-14 17:44:39 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2021-10-14 17:44:40 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2021-10-14 17:44:40 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2021-10-14 17:44:40 driver-btm-api.c:449:change_freq_one_chain: chain[0] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2021-10-14 17:44:40 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2021-10-14 17:44:40 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2021-10-14 17:44:40 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2021-10-14 17:44:40 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2021-10-14 17:44:40 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2021-10-14 17:44:40 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2021-10-14 17:44:41 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2021-10-14 17:44:42 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2021-10-14 17:44:42 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2021-10-14 17:44:42 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2021-10-14 17:44:42 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2021-10-14 17:44:42 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2021-10-14 17:44:42 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2021-10-14 17:44:42 driver-btm-api.c:612:set_timeout: freq 720 final timeout=163
2021-10-14 17:44:42 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 16.90 ...
2021-10-14 17:44:48 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 0
2021-10-14 17:45:01 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 1
2021-10-14 17:45:07 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 0
2021-10-14 17:45:17 power_api.c:124:check_voltage_multi: retry time: 0
2021-10-14 17:45:19 power_api.c:86:get_average_voltage: chain[0], voltage is: 16.783271 
2021-10-14 17:45:20 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 1
2021-10-14 17:45:21 power_api.c:86:get_average_voltage: chain[1], voltage is: 16.771025 
2021-10-14 17:45:22 power_api.c:86:get_average_voltage: chain[2], voltage is: 16.979209 
2021-10-14 17:45:22 power_api.c:97:get_average_voltage: aveage voltage is: 16.844502 
2021-10-14 17:45:22 frequency.c:540:get_current_min_freq: current min freq 720
2021-10-14 17:45:22 driver-btm-api.c:1660:check_clock_counter: freq 720 clock_counter_limit 92
2021-10-14 17:45:27 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 0
2021-10-14 17:45:40 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 1
2021-10-14 17:45:47 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 0
2021-10-14 17:46:00 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 1
2021-10-14 17:46:04 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 5, core = 0, found 0, clock counter 0x00000000
2021-10-14 17:46:04 driver-btm-api.c:2097:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.
2021-10-14 17:46:04 thread.c:799:create_check_system_status_thread: create thread
2021-10-14 17:46:04 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2021-10-14 17:46:04 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2021-10-14 17:46:09 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2021-10-14 17:46:10 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 0
2021-10-14 17:46:14 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4
2021-10-14 17:46:24 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 1
2021-10-14 17:46:30 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 0
2021-10-14 17:46:43 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 1
2021-10-14 17:46:50 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 0
2021-10-14 17:47:03 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 1
2021-10-14 17:47:09 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 0
2021-10-14 17:47:23 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 1
2021-10-14 17:47:31 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 0
2021-10-14 17:47:44 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 1
2021-10-14 17:47:51 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 0
2021-10-14 17:48:04 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 1
2021-10-14 17:48:11 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 0
2021-10-14 17:48:24 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 1
2021-10-14 17:48:30 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 0
2021-10-14 17:48:43 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 1
2021-10-14 17:48:52 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 0
2021-10-14 17:49:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 1
2021-10-14 17:49:12 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 0
2021-10-14 17:49:25 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 1
2021-10-14 17:49:31 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 0
2021-10-14 17:49:44 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 1
2021-10-14 17:49:51 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 0
2021-10-14 17:50:04 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 1
2021-10-14 17:50:13 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 0
2021-10-14 17:50:26 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 1
2021-10-14 17:50:32 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 0
2021-10-14 17:50:46 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 48, reg = 1
2021-10-14 17:50:52 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 0
2021-10-14 17:51:05 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 168, reg = 1
2021-10-14 17:51:12 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 0
2021-10-14 17:51:13 thread.c:422:is_zero_nonce_happened: chain_nonce[0] = 0
2021-10-14 17:51:13 thread.c:422:is_zero_nonce_happened: chain_nonce[1] = 15697
2021-10-14 17:51:13 thread.c:422:is_zero_nonce_happened: chain_nonce[2] = 15686
2021-10-14 17:51:13 thread.c:539:check_system_work_thread: 0 nonce rate happened after retry, wait for hash rate protect later.
2021-10-14 17:51:25 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 1
2021-10-14 17:51:33 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 64, reg = 0

When no asics found on board 1:

Code:

2021-10-14 17:24:48 driver-btm-api.c:631:init_freq_mode: This is scan-user version
2021-10-14 17:24:48 driver-btm-api.c:1994:bitmain_soc_init: opt_multi_version     = 1
2021-10-14 17:24:48 driver-btm-api.c:1995:bitmain_soc_init: opt_bitmain_ab        = 1
2021-10-14 17:24:48 driver-btm-api.c:1996:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-10-14 17:24:48 driver-btm-api.c:1997:bitmain_soc_init: Miner compile time: Tue Dec 24 16:13:07 CST 2019 type: Antminer T17
2021-10-14 17:24:48 driver-btm-api.c:1998:bitmain_soc_init: commit version: e93a09b 2019-12-24 16:03:45, build by: lol 2019-12-24 16:19:49
2021-10-14 17:24:48 driver-btm-api.c:1810:show_sn: no SN got, please write SN to /nvdata/sn
2021-10-14 17:24:48 driver-btm-api.c:1135:miner_device_init: Detect 256MB control board of XILINX
2021-10-14 17:24:48 driver-btm-api.c:1083:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-10-14 17:24:48 thread.c:789:create_read_nonce_reg_thread: create thread
2021-10-14 17:24:54 driver-btm-api.c:1067:init_miner_version: miner ID : 803c95042b104814
2021-10-14 17:24:54 driver-btm-api.c:1073:init_miner_version: FPGA Version = 0xB013
2021-10-14 17:24:56 eeprom.c:431:check_pattern_test_level: L1 board
2021-10-14 17:24:58 eeprom.c:431:check_pattern_test_level: L1 board
2021-10-14 17:24:59 eeprom.c:431:check_pattern_test_level: L1 board
2021-10-14 17:24:59 driver-btm-api.c:705:get_product_id: product_id[0] = 1
2021-10-14 17:24:59 driver-btm-api.c:705:get_product_id: product_id[1] = 1
2021-10-14 17:24:59 driver-btm-api.c:705:get_product_id: product_id[2] = 1
2021-10-14 17:24:59 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[0] = 1
2021-10-14 17:24:59 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[1] = 1
2021-10-14 17:24:59 driver-btm-api.c:1633:get_ccdly_opt: ccdly_opt[2] = 1
2021-10-14 17:24:59 driver-btm-api.c:1877:bitmain_board_init: g_ccdly_opt = 1
2021-10-14 17:24:59 driver-btm-api.c:644:_set_project_type: project:2
2021-10-14 17:24:59 driver-btm-api.c:674:_set_project_type: Project type: Antminer T17
2021-10-14 17:24:59 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-10-14 17:24:59 driver-btm-api.c:686:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-10-14 17:24:59 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-10-14 17:24:59 driver-btm-api.c:686:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-10-14 17:24:59 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-10-14 17:24:59 driver-btm-api.c:686:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-10-14 17:24:59 driver-btm-api.c:1897:bitmain_board_init: Fan check passed.
2021-10-14 17:25:01 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-10-14 17:25:05 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2021-10-14 17:25:06 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-10-14 17:25:10 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2021-10-14 17:25:12 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-10-14 17:25:15 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2021-10-14 17:25:15 thread.c:784:create_pic_heart_beat_thread: create thread
2021-10-14 17:25:15 power_api.c:55:power_init: power init ... 
2021-10-14 17:25:15 driver-btm-api.c:1907:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-10-14 17:25:47 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2021-10-14 17:25:53 power_api.c:124:check_voltage_multi: retry time: 0
2021-10-14 17:25:54 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.003701 
2021-10-14 17:25:56 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.003701 
2021-10-14 17:25:58 power_api.c:86:get_average_voltage: chain[2], voltage is: 16.966963 
2021-10-14 17:25:58 power_api.c:97:get_average_voltage: aveage voltage is: 16.991455 
2021-10-14 17:25:58 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2021-10-14 17:25:58 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-10-14 17:25:58 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2021-10-14 17:25:58 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2021-10-14 17:25:58 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-10-14 17:26:09 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 0
2021-10-14 17:26:19 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 1
2021-10-14 17:26:29 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 2
2021-10-14 17:26:29 driver-btm-api.c:1037:check_asic_number: Chain 0 only find 0 asic, will power off hash board 0
2021-10-14 17:26:41 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2021-10-14 17:26:51 driver-btm-api.c:1010:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2021-10-14 17:26:54 driver-btm-api.c:348:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2021-10-14 17:26:54 driver-btm-api.c:348:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2021-10-14 17:26:54 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2021-10-14 17:26:54 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2021-10-14 17:26:54 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2021-10-14 17:26:54 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2021-10-14 17:26:54 driver-btm-api.c:1660:check_clock_counter: freq 50 clock_counter_limit 6
2021-10-14 17:26:55 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2021-10-14 17:26:55 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2021-10-14 17:26:55 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-10-14 17:26:55 voltage[1] = 1690
2021-10-14 17:26:55 voltage[2] = 1690
2021-10-14 17:26:55 power_api.c:140:set_working_voltage: working_voltage = 16.900000
2021-10-14 17:26:56 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2021-10-14 17:26:57 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2021-10-14 17:26:57 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2021-10-14 17:26:57 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2021-10-14 17:26:57 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2021-10-14 17:26:59 driver-btm-api.c:248:check_bringup_temp: Bring up temperature is 25
2021-10-14 17:26:59 thread.c:804:create_check_miner_status_thread: create thread
2021-10-14 17:26:59 thread.c:794:create_set_miner_status_thread: create thread
2021-10-14 17:26:59 driver-btm-api.c:581:calculate_timeout: dev->timeout = 392
2021-10-14 17:26:59 thread.c:779:create_temperature_monitor_thread: create thread
2021-10-14 17:26:59 freq_tuning.c:154:freq_tuning_get_max_freq: Max freq of tuning is 760
2021-10-14 17:26:59 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.80 ...
2021-10-14 17:27:30 power_api.c:124:check_voltage_multi: retry time: 0
2021-10-14 17:27:33 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.781328 
2021-10-14 17:27:36 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.769082 
2021-10-14 17:27:36 power_api.c:97:get_average_voltage: aveage voltage is: 17.775205 
2021-10-14 17:27:36 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2021-10-14 17:27:37 driver-btm-api.c:449:change_freq_one_chain: chain[1] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2021-10-14 17:27:38 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2021-10-14 17:27:38 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2021-10-14 17:27:38 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2021-10-14 17:27:38 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2021-10-14 17:27:38 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2021-10-14 17:27:38 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2021-10-14 17:27:38 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2021-10-14 17:27:38 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2021-10-14 17:27:38 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2021-10-14 17:27:39 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2021-10-14 17:27:39 driver-btm-api.c:449:change_freq_one_chain: chain[2] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2021-10-14 17:27:39 driver-btm-api.c:612:set_timeout: freq 720 final timeout=163
2021-10-14 17:27:39 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 16.90 ...
2021-10-14 17:27:58 thread.c:642:check_temperature: over max temp, pcb temp 59 (max 80), chip temp 106(max 103)
2021-10-14 17:27:58 driver-btm-api.c:201:set_miner_status: ERROR_TEMP_TOO_HIGH
2021-10-14 17:27:58 driver-btm-api.c:142:stop_mining: stop mining: over max temp
2021-10-14 17:27:58 thread.c:824:cancel_temperature_monitor_thread: cancel thread
2021-10-14 17:27:58 thread.c:834:cancel_read_nonce_reg_thread: cancel thread
2021-10-14 17:27:58 driver-btm-api.c:128:killall_hashboard: ****power off hashboard****
2021-10-14 17:28:09 power_api.c:124:check_voltage_multi: retry time: 0
2021-10-14 17:28:11 power_api.c:86:get_average_voltage: chain[1], voltage is: 16.948594 
2021-10-14 17:28:13 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.205762 
2021-10-14 17:28:13 power_api.c:97:get_average_voltage: aveage voltage is: 17.077178 
2021-10-14 17:28:13 frequency.c:540:get_current_min_freq: current min freq 720
2021-10-14 17:28:13 driver-btm-api.c:1660:check_clock_counter: freq 720 clock_counter_limit 92
2021-10-14 17:28:16 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 1, asic = 5, core = 0, found 0, clock counter 0x00000000
2021-10-14 17:28:16 driver-btm-api.c:2097:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.
2021-10-14 17:28:16 thread.c:799:create_check_system_status_thread: create thread
2021-10-14 17:28:16 driver-btm-api.c:2113:bitmain_soc_init: Init done!
2021-10-14 17:28:16 driver-btm-api.c:201:set_miner_status: STATUS_INIT
2021-10-14 17:28:21 driver-btm-api.c:201:set_miner_status: STATUS_OKAY
2021-10-14 17:28:25 driver-btm-api.c:1293:dhash_chip_send_job: Version num 4

I wouldnt want to use any permeneatny adhesive. Im looking to apply solder. What solder do you know I can use for this that can be taken off and on.

Also I have a whole bunch of boards that have the same exact errors when I run the test fixture. All the asic are found but I still get a temp sensor error.

Code:

1970-01-01 00:01:52 register.c:185:read_asic_reg_with_addr: read asic reg timeout: expect chain = 0, chip = 14, reg = 28
1970-01-01 00:01:52 register.c:185:read_asic_reg_with_addr: read asic reg timeout: expect chain = 0, chip = 14, reg = 28
1970-01-01 00:01:53 temperature.c:744:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 14, reg = 1
...
1970-01-01 00:01:53 register.c:185:read_asic_reg_with_addr: read asic reg timeout: expect chain = 0, chip = 10, reg = 28
1970-01-01 00:01:53 register.c:185:read_asic_reg_with_addr: read asic reg timeout: expect chain = 0, chip = 10, reg = 28
1970-01-01 00:01:54 temperature.c:744:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 10, reg = 1
...
1970-01-01 00:01:54 register.c:185:read_asic_reg_with_addr: read asic reg timeout: expect chain = 0, chip = 54, reg = 28
1970-01-01 00:01:54 register.c:185:read_asic_reg_with_addr: read asic reg timeout: expect chain = 0, chip = 54, reg = 28
1970-01-01 00:01:54 register.c:185:read_asic_reg_with_addr: read asic reg timeout: expect chain = 0, chip = 54, reg = 28
1970-01-01 00:01:55 temperature.c:744:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 54, reg = 1
1970-01-01 00:01:55 register.c:185:read_asic_reg_with_addr: read asic reg timeout: expect chain = 0, chip = 50, reg = 28
1970-01-01 00:01:55 register.c:185:read_asic_reg_with_addr: read asic reg timeout: expect chain = 0, chip = 50, reg = 28
...
1970-01-01 00:01:56 temperature.c:744:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 50, reg = 1
1970-01-01 00:01:56 single_board_test.c:1659:wait_warm_up: temper sensor bad

I have this same exact error for over 10 boards. Also the the error states chip 50, 54, 10, 14 as being bad chips but I get this same exact error on many boards. Cant all have the same exact chips with the same exact error. What could this be? My boards are in 100% perfect condition and all the sudden stopped working one day. Showed temp sensor errors and then stopped working completely. Running this test fixture is showing temo sensor is bad but that cant be either. Something is wrong and I dont know how to find the problem. Please advise. Thank you.

[wndsnb]

...

I wouldn't really recommend trying to fix yourself. Removing/replacing heatsinks and chips on these hashboards is not easy, and without lots of practice, you'd probably just create more issues.

You can search back through this thread to find some potential remedies that may get the board up at least temporarily. Changing the temperature and/or orientation of the miner can sometimes close broken solder joints or open shorts caused by excess solder on the board. In my experience, these are the most likely causes.

Best option is to find an experienced repair shop.

[mikeywith]

Welcome back man, you went missing for quite a while, by the way, if you are interested, I could add your name here > https://bitcointalk.org/index.php?topic=5297994.0, you are the most experienced member in fixing these hash boards, trusted and can probably do better than most of those overpriced services listed, check it out and let me know.

I have an issue with my T17, one just 1 hashboard. Sometimes i get 0 asic found sometimes it finds all 30. But in any case, I get the error for all temp sensors on the board. I think I've went through most of the posts here and it most likely resembles the issue I quoted below. As I could see, most likely its loose heatsink, but after my (inexperienced) inspection, none seems loose when tested with mild pressure.

It's more like a bad chip connection than just a loose heatsink, in fact, if the heatsink isn't shorting anything, the miner will still run for a very short while before showing "Over-Temp", but getting the temp sensors errors is probably because of a dead/burnt chip or a bad connection between one of the chip and PCB.

This problem could also be caused by a bad PSU, do you have another PSU to test with?

[wndsnb]

Thanks, but I have no interest in repairing miners as a service. If I charged enough to make it worth my time I'd be even more expensive than the overpriced services already listed...

Still have >100 dead hashboards of my own to repair anyway which will probably take me more than a year to get through.

[HagssFIN]

Whoah, so running a big farm like that easily becomes your full time job if you can also do repairing yourself

[wndsnb]

I'd imagine so. I don't run a big farm but nearly all this dead gear I have I bought from a large farm that shut down last year. They had full-time technicians to repair miners but when they shut down they had piles of dead gear that the technicians either didn't get to or couldn't repair.

[robertpaulsen]

Best option is to find an experienced repair shop.

Thanks, I'll probably do that.

This problem could also be caused by a bad PSU, do you have another PSU to test with?

No, unfortunately not. I guess it could be the soldier or a burnt chip, although, could there be a log of "find 30 asic" even with a burnt chip? Seems kinda contradictory.