sxo13 (OP)
Newbie
Offline
Activity: 14
Merit: 1
|
|
February 14, 2020, 09:42:59 AM Last edit: February 14, 2020, 11:42:11 AM by sxo13 |
|
Hi all, If somebody could help to interpret the S9K logs, it would be much appreciated. My s9k models stopped working and I suspect it has to done with the changing environment temperature but cant interpret properly the logs due to lack of experience with them. They are in an environment temperature of ~15C(10-20C) on a shelf along with other S9(all working normally) meaning that the hardware is constantly at around 30C at cold start. Earlier it was 5-10C warmer environment temp. here. I flashed with the latest january firmware but no difference. Weird is, they all stopped to work with a few hours difference. Network setup is all ok, the issue is not there to find I assume. The kernel log sample: Booting Linux on physical CPU 0x0 Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: Xilinx Zynq cma: Reserved 16 MiB at 0x0e000000 Memory policy: Data cache writealloc On node 0 totalpages: 61440 free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000 Normal zone: 480 pages used for memmap Normal zone: 0 pages reserved Normal zone: 61440 pages, LIFO batch:15 percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152 pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960 Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 203784K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25592K reserved, 16384K cma-reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xcf800000 - 0xff800000 ( 768 MB) lowmem : 0xc0000000 - 0xcf000000 ( 240 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc090c424 (9234 kB) .init : 0xc0a00000 - 0xc0b00000 (1024 kB) .data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB) .bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB) Preemptible hierarchical RCU implementation. Build-time adjustment of leaf fanout to 32. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 NR_IRQS:16 nr_irqs:16 16 efuse mapped to cf800000 ps7-slcr mapped to cf802000 L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 zynq_clock_init: clkc starts at cf802100 Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns ps7-ttc #0 at cf80a000, irq=18 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100058 CPU1: failed to boot: -1 Brought up 1 CPUs SMP: Total of 1 processors activated (666.66 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor menu hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb media: Linux media interface: v0.10 Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered EDAC MC: Ver: 3.0.0 Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 12552K (ccebe000 - cdb00000) hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available futex hash table entries: 512 (order: 3, 32768 bytes) workingset: timestamp_bits=28 max_order=16 bucket_order=0 jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps console [ttyPS0] enabled xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000 [drm] Initialized drm 1.1.0 20060810 brd: module loaded loop: module loaded CAN device driver interface gpiod_set_value: invalid GPIO libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00) Broadcom BCM5241 e000b000.etherne:00: attached PHY driver [Broadcom BCM5241] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1) e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k e1000e: Copyright(c) 1999 - 2015 Intel Corporation. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice i2c /dev entries driver Xilinx Zynq CpuIdle Driver started sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA ledtrig-cpu: registered to indicate activity on CPUs usbcore: registered new interface driver usbhid usbhid: USB HID core driver nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda nand: Micron MT29F2G08ABAGAWP nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128 nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 6 ofpart partitions found on MTD device pl35x-nand Creating 6 MTD partitions on "pl35x-nand": 0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel" 0x000002800000-0x000004800000 : "ramfs" 0x000004800000-0x000005000000 : "configs" 0x000005000000-0x000006000000 : "reserve" 0x000006000000-0x000008000000 : "ramfs-bak" 0x000008000000-0x000010000000 : "reserve1" NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20120528 t) can: netlink gateway (rev 20130117) max_hops=1 zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05' zynq_pm_late_init: Unable to map DDRC IO memory. Registering SWP/SWPB emulation handler hctosys: unable to open rtc device (rtc0) ALSA device list: No soundcards found. RAMDISK: gzip image found at block 0 EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities EXT4-fs (ram0): mounted filesystem without journal. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 1:0. devtmpfs: mounted Freeing unused kernel memory: 1024K (c0a00000 - c0b00000) EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr random: dd urandom read with 0 bits of entropy available ubi0: attaching mtd2 ubi0: scanning is finished ubi0: attached mtd2 (name "configs", size 8 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 19/9, WL threshold: 4096, image sequence number: 237714726 ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40 ubi0: background thread "ubi_bgt0d" started, PID 708 UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711 UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs" UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs) UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model ubi1: attaching mtd5 ubi1: scanning is finished ubi1: attached mtd5 (name "reserve1", size 128 MiB) ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0 ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi1: max/mean erase counter: 26/12, WL threshold: 4096, image sequence number: 914180297 ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36 ubi1: background thread "ubi_bgt1d" started, PID 720 UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723 UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1" UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs) UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB) UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BCBDE5E0-4C0B-4978-9734-FC58D9F68227, small LPT model IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz macb e000b000.ethernet eth0: link up (100/Full) IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready In axi fpga driver! request_mem_region OK! AXI fpga dev virtual address is 0xcfb38000 *base_vir_addr = 0xab00d In fpga mem driver! request_mem_region OK! fpga mem virtual address is 0xd2000000 random: nonblocking pool is initialized macb e000b000.ethernet eth0: link down macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz macb e000b000.ethernet eth0: link up (100/Half) [2020-02-14 09:07:00.495] httpListenThread start ret=0 [2020-02-14 09:07:30.515] start listen on 6060 ... [2020-02-14 09:13:26.552] setStartTimePoint total_tv_start_sys=402 total_tv_end_sys=403
2020-02-14 09:07:00 cgminer.c:11470:cnt_of_proc: pidof cgminer command result is:1143
2020-02-14 09:07:00 cgminer.c:11471:cnt_of_proc: strlen is: 5 2020-02-14 09:07:00 cgminer.c:11492:cnt_of_proc: Parsed proc id is: 1143 2020-02-14 09:07:00 cgminer.c:11504:cnt_of_proc: 1 instance of cgminer is already Running on this machine 2020-02-14 09:07:00 driver-btm-soc.c:6311:bitmain_soc_init: This is Antminer S9k scan user version 2020-02-14 09:07:00 driver-btm-soc.c:6317:bitmain_soc_init: special mode: disabled 2020-02-14 09:07:00 driver-btm-soc.c:6324:bitmain_soc_init: This is high performance mode 2020-02-14 09:07:00 driver-btm-soc.c:6329:bitmain_soc_init: last commit version: 94e8f08 commit time: 2019-10-31 10:33:22 build: 2019-12-13 10:14:11 2020-02-14 09:07:00 driver-btm-soc.c:6350:bitmain_soc_init: Detect 256MB control board of XILINX 2020-02-14 09:07:00 driver-btm-soc.c:6353:bitmain_soc_init: Miner compile time: Fri Dec 13 10:01:09 CST 2019 type: Antminer S9k 2020-02-14 09:07:00 driver-btm-soc.c:849:check_chain: get_hash_on_plug is 0x7 2020-02-14 09:07:00 driver-btm-soc.c:861:check_chain: !! chain[0]is exist 2020-02-14 09:07:00 driver-btm-soc.c:861:check_chain: !! chain[1]is exist 2020-02-14 09:07:00 driver-btm-soc.c:861:check_chain: !! chain[2]is exist 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 00000000 7e ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000070 ff ff ff ff ff ff ff ff ff 01 02 1f fb 28 fc ff 00000080 ff ff ff ff ff ff ff c3 4d 4d 4d 4d 4d 4d 4d 4d 00000090 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 000000a0 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 000000b0 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 000000c0 4d 4d 4d 4d 00 ff ff ff ff ff ff ff ff ff ff ff 000000d0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 000000e0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 000000f0 ff ff ff ff e3 11 00 00 80 ff ff ff 39 10 a4 bd 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 00000000 7e ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000070 ff ff ff ff ff ff ff ff ff 01 02 1f fc 28 fd ff 00000080 ff ff ff ff ff ff ff c3 4d 4d 4d 4d 4d 4d 4d 4d 00000090 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 000000a0 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 000000b0 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 000000c0 4d 4d 4d 4d 02 ff ff ff ff ff ff ff ff ff ff ff 000000d0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 000000e0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 000000f0 ff ff ff ff 77 11 00 00 80 ff ff ff 39 10 e5 c6 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 00000000 7e ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00000070 ff ff ff ff ff ff ff ff ff 01 02 1f fb 28 fc ff 00000080 ff ff ff ff ff ff ff c3 4d 4d 4d 4d 4d 4d 4d 4d 00000090 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 000000a0 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 000000b0 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 4d 000000c0 4d 4d 4d 4d 00 ff ff ff ff ff ff ff ff ff ff ff 000000d0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 000000e0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 000000f0 ff ff ff ff df 11 00 00 80 ff ff ff 39 10 64 7d
read chain[0] hardware info: major type: 0 minor type: 0 chip level: 2 bom version: 0x10 pcb version: 0x39 fixture 8pattern result: L0
read chain[1] hardware info: major type: 0 minor type: 0 chip level: 2 bom version: 0x10 pcb version: 0x39 fixture 8pattern result: L2
read chain[2] hardware info: major type: 0 minor type: 0 chip level: 2 bom version: 0x10 pcb version: 0x39 fixture 8pattern result: L0
sweep config for eco mode: sweep_start_voltage: 9.44 max_aging_voltage: 9.84 sweep_min_freq: 270M sweep_max_freq: 310M
sweep config for hpf mode: sweep_start_voltage: 9.90 max_aging_voltage: 10.30 sweep_min_freq: 355M sweep_max_freq: 385M 2020-02-14 09:07:12 driver-btm-soc.c:5770:get_freq_result_from_eeprom: orginal chip freq: chain 0 freq: 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385
chain 1 freq: 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385
chain 2 freq: 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385
2020-02-14 09:07:13 driver-btm-soc.c:6443:bitmain_soc_init: reset all... 2020-02-14 09:07:15 driver-btm-soc.c:6451:bitmain_soc_init: miner ID : 815cc4417b808854 2020-02-14 09:07:15 driver-btm-soc.c:6112:init_miner_version: FPGA Version = 0xB00D 2020-02-14 09:07:34 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[0] PIC software version: 177 2020-02-14 09:07:35 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[1] PIC software version: 177 2020-02-14 09:07:35 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[2] PIC software version: 177 2020-02-14 09:07:35 power.c:185:power_init: power init ... 2020-02-14 09:07:35 driver-btm-soc.c:4877:get_working_voltage_from_eeprom: get working vol [ 9.90] from chain[0] eeprom 2020-02-14 09:07:35 power.c:232:set_working_voltage_by_chain: chain[0] working_voltage = 9.90 2020-02-14 09:07:35 driver-btm-soc.c:4877:get_working_voltage_from_eeprom: get working vol [ 9.90] from chain[1] eeprom 2020-02-14 09:07:35 power.c:232:set_working_voltage_by_chain: chain[1] working_voltage = 9.90 2020-02-14 09:07:35 driver-btm-soc.c:4877:get_working_voltage_from_eeprom: get working vol [ 9.90] from chain[2] eeprom 2020-02-14 09:07:35 power.c:232:set_working_voltage_by_chain: chain[2] working_voltage = 9.90 2020-02-14 09:07:35 driver-btm-soc.c:5560:update_highest_voltage: chain 0 hpf working voltage 9.90 2020-02-14 09:07:35 driver-btm-soc.c:5560:update_highest_voltage: chain 1 hpf working voltage 9.90 2020-02-14 09:07:35 driver-btm-soc.c:5560:update_highest_voltage: chain 2 hpf working voltage 9.90 2020-02-14 09:07:35 driver-btm-soc.c:5569:update_highest_voltage: open core at max voltage 10.20 2020-02-14 09:07:35 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[0] setting to highest voltage: 10.20 ... 2020-02-14 09:07:38 power.c:707:set_iic_power_by_voltage: now setting voltage to : 10.20 2020-02-14 09:07:38 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[1] setting to highest voltage: 10.20 ... 2020-02-14 09:07:39 power.c:707:set_iic_power_by_voltage: now setting voltage to : 10.20 2020-02-14 09:07:39 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[2] setting to highest voltage: 10.20 ... 2020-02-14 09:07:40 power.c:707:set_iic_power_by_voltage: now setting voltage to : 10.20 2020-02-14 09:07:40 driver-btm-soc.c:1259:get_ideal_hash_rate: get ideal hash rate 13500 2020-02-14 09:07:40 eeprom.c:675:travel_eeprom_store: chain[0] data in eeprom is: magic number: 0x7e freq data per ASIC: IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 voltage: 11.10 V hash rate: -0001 GH/s
freq data per ASIC in mode2: IC[000]:385 IC[001]:385 IC[002]:385 IC[003]:385 IC[004]:385 IC[005]:385 IC[006]:385 IC[007]:385 IC[008]:385 IC[009]:385 IC[010]:385 IC[011]:385 IC[012]:385 IC[013]:385 IC[014]:385 IC[015]:385 IC[016]:385 IC[017]:385 IC[018]:385 IC[019]:385 IC[020]:385 IC[021]:385 IC[022]:385 IC[023]:385 IC[024]:385 IC[025]:385 IC[026]:385 IC[027]:385 IC[028]:385 IC[029]:385 IC[030]:385 IC[031]:385 IC[032]:385 IC[033]:385 IC[034]:385 IC[035]:385 IC[036]:385 IC[037]:385 IC[038]:385 IC[039]:385 IC[040]:385 IC[041]:385 IC[042]:385 IC[043]:385 IC[044]:385 IC[045]:385 IC[046]:385 IC[047]:385 IC[048]:385 IC[049]:385 IC[050]:385 IC[051]:385 IC[052]:385 IC[053]:385 IC[054]:385 IC[055]:385 IC[056]:385 IC[057]:385 IC[058]:385 IC[059]:385 voltage in mode2: 9.90 V hash rate in mode2: 04579 GH/s
2020-02-14 09:07:40 eeprom.c:675:travel_eeprom_store: chain[1] data in eeprom is: magic number: 0x7e freq data per ASIC: IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 voltage: 11.10 V hash rate: -0001 GH/s
freq data per ASIC in mode2: IC[000]:385 IC[001]:385 IC[002]:385 IC[003]:385 IC[004]:385 IC[005]:385 IC[006]:385 IC[007]:385 IC[008]:385 IC[009]:385 IC[010]:385 IC[011]:385 IC[012]:385 IC[013]:385 IC[014]:385 IC[015]:385 IC[016]:385 IC[017]:385 IC[018]:385 IC[019]:385 IC[020]:385 IC[021]:385 IC[022]:385 IC[023]:385 IC[024]:385 IC[025]:385 IC[026]:385 IC[027]:385 IC[028]:385 IC[029]:385 IC[030]:385 IC[031]:385 IC[032]:385 IC[033]:385 IC[034]:385 IC[035]:385 IC[036]:385 IC[037]:385 IC[038]:385 IC[039]:385 IC[040]:385 IC[041]:385 IC[042]:385 IC[043]:385 IC[044]:385 IC[045]:385 IC[046]:385 IC[047]:385 IC[048]:385 IC[049]:385 IC[050]:385 IC[051]:385 IC[052]:385 IC[053]:385 IC[054]:385 IC[055]:385 IC[056]:385 IC[057]:385 IC[058]:385 IC[059]:385 voltage in mode2: 9.90 V hash rate in mode2: 04471 GH/s
2020-02-14 09:07:40 eeprom.c:675:travel_eeprom_store: chain[2] data in eeprom is: magic number: 0x7e freq data per ASIC: IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 voltage: 11.10 V hash rate: -0001 GH/s
freq data per ASIC in mode2: IC[000]:385 IC[001]:385 IC[002]:385 IC[003]:385 IC[004]:385 IC[005]:385 IC[006]:385 IC[007]:385 IC[008]:385 IC[009]:385 IC[010]:385 IC[011]:385 IC[012]:385 IC[013]:385 IC[014]:385 IC[015]:385 IC[016]:385 IC[017]:385 IC[018]:385 IC[019]:385 IC[020]:385 IC[021]:385 IC[022]:385 IC[023]:385 IC[024]:385 IC[025]:385 IC[026]:385 IC[027]:385 IC[028]:385 IC[029]:385 IC[030]:385 IC[031]:385 IC[032]:385 IC[033]:385 IC[034]:385 IC[035]:385 IC[036]:385 IC[037]:385 IC[038]:385 IC[039]:385 IC[040]:385 IC[041]:385 IC[042]:385 IC[043]:385 IC[044]:385 IC[045]:385 IC[046]:385 IC[047]:385 IC[048]:385 IC[049]:385 IC[050]:385 IC[051]:385 IC[052]:385 IC[053]:385 IC[054]:385 IC[055]:385 IC[056]:385 IC[057]:385 IC[058]:385 IC[059]:385 voltage in mode2: 9.90 V hash rate in mode2: 04575 GH/s
2020-02-14 09:07:41 driver-btm-soc.c:6494:bitmain_soc_init: fan_eft : 0 fan_pwm : 0 2020-02-14 09:07:41 driver-btm-soc.c:6141:bring_up_chain:
bring up chain 0 2020-02-14 09:07:41 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff 2020-02-14 09:08:14 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe 2020-02-14 09:08:16 driver-btm-soc.c:3807:check_asic_num: without pre_open_core chain 0, find asic num = 60 2020-02-14 09:08:19 driver-btm-soc.c:4630:set_freq_by_chain: chain[0] set freq:100.00 2020-02-14 09:08:19 driver-btm-soc.c:3853:open_core_BM1393_pre_open: pre open core = 13 2020-02-14 09:08:20 driver-btm-soc.c:3733:pre_open_core_one_chain: for chain 0 2020-02-14 09:08:20 temperature.c:591:is_eeprom_tempsensor_data_correct: check sensor info ... 2020-02-14 09:08:20 temperature.c:606:is_eeprom_tempsensor_data_correct: sensor type is TMP451 2020-02-14 09:08:20 temperature.c:618:is_eeprom_tempsensor_data_correct: 2 2020-02-14 09:08:20 temperature.c:632:is_eeprom_tempsensor_data_correct: sensor num is 2 2020-02-14 09:08:20 temperature.c:641:is_eeprom_tempsensor_data_correct: sensor pos = 31, 40, 0, 0 2020-02-14 09:08:20 temperature.c:659:is_eeprom_tempsensor_data_correct: chain[0] temp sensor info, correct! 2020-02-14 09:08:20 temperature.c:748:check_eeprom_calibration_data: chain[0] no need to calibrate ! 2020-02-14 09:08:20 temperature.c:524:is_tempsensor_data_correct: Bad,temp_info.type = 0 2020-02-14 09:08:20 temperature.c:763:calibration_sensor_offset: chain[0] temp info,Bad. Reload from eeprom.. sensor type = 1,sensor num = 2 sensor pos: 31 40 0 0 0 0 sensor offset: -5 -4 0 0 0 0 2020-02-14 09:08:20 temperature.c:801:calibration_sensor_offset: get temp info from eeprom,just use it! 2020-02-14 09:08:20 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x7a61, cmd_buf[2]=0x1a000000, misc=0x7a61 2020-02-14 09:08:20 temperature.c:818:calibration_sensor_offset: Chain[0] chip[31] use PIC middle temp offset=-5, typeID=55 2020-02-14 09:08:21 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[0] Chip[31] local:0 remote:0 offset:-5 2020-02-14 09:08:21 temperature.c:870:calibration_sensor_offset: Chain[0] Chip[31] get middle temp offset=-5 typeID=55 2020-02-14 09:08:21 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x7a61, cmd_buf[2]=0x13000000, misc=0x7a61 2020-02-14 09:08:21 temperature.c:818:calibration_sensor_offset: Chain[0] chip[40] use PIC middle temp offset=-4, typeID=55 2020-02-14 09:08:21 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[0] Chip[40] local:0 remote:0 offset:-4 2020-02-14 09:08:21 temperature.c:870:calibration_sensor_offset: Chain[0] Chip[40] get middle temp offset=-4 typeID=55 2020-02-14 09:08:21 driver-btm-soc.c:6141:bring_up_chain:
bring up chain 1 2020-02-14 09:08:22 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe 2020-02-14 09:08:53 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc 2020-02-14 09:08:55 driver-btm-soc.c:3807:check_asic_num: without pre_open_core chain 1, find asic num = 60 2020-02-14 09:08:58 driver-btm-soc.c:4630:set_freq_by_chain: chain[1] set freq:100.00 2020-02-14 09:08:58 driver-btm-soc.c:3853:open_core_BM1393_pre_open: pre open core = 13 2020-02-14 09:08:59 driver-btm-soc.c:3733:pre_open_core_one_chain: for chain 1 2020-02-14 09:08:59 temperature.c:591:is_eeprom_tempsensor_data_correct: check sensor info ... 2020-02-14 09:08:59 temperature.c:606:is_eeprom_tempsensor_data_correct: sensor type is TMP451 2020-02-14 09:08:59 temperature.c:618:is_eeprom_tempsensor_data_correct: 2 2020-02-14 09:08:59 temperature.c:632:is_eeprom_tempsensor_data_correct: sensor num is 2 2020-02-14 09:08:59 temperature.c:641:is_eeprom_tempsensor_data_correct: sensor pos = 31, 40, 0, 0 2020-02-14 09:08:59 temperature.c:659:is_eeprom_tempsensor_data_correct: chain[1] temp sensor info, correct! 2020-02-14 09:08:59 temperature.c:748:check_eeprom_calibration_data: chain[1] no need to calibrate ! 2020-02-14 09:08:59 temperature.c:524:is_tempsensor_data_correct: Bad,temp_info.type = 0 2020-02-14 09:08:59 temperature.c:763:calibration_sensor_offset: chain[1] temp info,Bad. Reload from eeprom.. sensor type = 1,sensor num = 2 sensor pos: 31 40 0 0 0 0 sensor offset: -4 -3 0 0 0 0 2020-02-14 09:08:59 temperature.c:801:calibration_sensor_offset: get temp info from eeprom,just use it! 2020-02-14 09:08:59 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x7a61, cmd_buf[2]=0x1a000000, misc=0x7a61 2020-02-14 09:08:59 temperature.c:818:calibration_sensor_offset: Chain[1] chip[31] use PIC middle temp offset=-4, typeID=55 2020-02-14 09:09:00 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[1] Chip[31] local:0 remote:0 offset:-4 2020-02-14 09:09:00 temperature.c:870:calibration_sensor_offset: Chain[1] Chip[31] get middle temp offset=-4 typeID=55 2020-02-14 09:09:00 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x7a61, cmd_buf[2]=0x13000000, misc=0x7a61 2020-02-14 09:09:00 temperature.c:818:calibration_sensor_offset: Chain[1] chip[40] use PIC middle temp offset=-3, typeID=55 2020-02-14 09:09:00 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[1] Chip[40] local:0 remote:0 offset:-3 2020-02-14 09:09:00 temperature.c:870:calibration_sensor_offset: Chain[1] Chip[40] get middle temp offset=-3 typeID=55 2020-02-14 09:09:00 driver-btm-soc.c:6141:bring_up_chain:
bring up chain 2 2020-02-14 09:09:01 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc 2020-02-14 09:09:32 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8 2020-02-14 09:09:34 driver-btm-soc.c:3807:check_asic_num: without pre_open_core chain 2, find asic num = 60 2020-02-14 09:09:37 driver-btm-soc.c:4630:set_freq_by_chain: chain[2] set freq:100.00 2020-02-14 09:09:37 driver-btm-soc.c:3853:open_core_BM1393_pre_open: pre open core = 13 2020-02-14 09:09:38 driver-btm-soc.c:3733:pre_open_core_one_chain: for chain 2 2020-02-14 09:09:38 temperature.c:591:is_eeprom_tempsensor_data_correct: check sensor info ... 2020-02-14 09:09:38 temperature.c:606:is_eeprom_tempsensor_data_correct: sensor type is TMP451 2020-02-14 09:09:38 temperature.c:618:is_eeprom_tempsensor_data_correct: 2 2020-02-14 09:09:38 temperature.c:632:is_eeprom_tempsensor_data_correct: sensor num is 2 2020-02-14 09:09:38 temperature.c:641:is_eeprom_tempsensor_data_correct: sensor pos = 31, 40, 0, 0 2020-02-14 09:09:38 temperature.c:659:is_eeprom_tempsensor_data_correct: chain[2] temp sensor info, correct! 2020-02-14 09:09:38 temperature.c:748:check_eeprom_calibration_data: chain[2] no need to calibrate ! 2020-02-14 09:09:38 temperature.c:524:is_tempsensor_data_correct: Bad,temp_info.type = 0 2020-02-14 09:09:38 temperature.c:763:calibration_sensor_offset: chain[2] temp info,Bad. Reload from eeprom.. sensor type = 1,sensor num = 2 sensor pos: 31 40 0 0 0 0 sensor offset: -5 -4 0 0 0 0 2020-02-14 09:09:38 temperature.c:801:calibration_sensor_offset: get temp info from eeprom,just use it! 2020-02-14 09:09:38 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x7a61, cmd_buf[2]=0x1a000000, misc=0x7a61 2020-02-14 09:09:38 temperature.c:818:calibration_sensor_offset: Chain[2] chip[31] use PIC middle temp offset=-5, typeID=55 2020-02-14 09:09:39 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[2] Chip[31] local:0 remote:0 offset:-5 2020-02-14 09:09:39 temperature.c:870:calibration_sensor_offset: Chain[2] Chip[31] get middle temp offset=-5 typeID=55 2020-02-14 09:09:39 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x7a61, cmd_buf[2]=0x13000000, misc=0x7a61 2020-02-14 09:09:39 temperature.c:818:calibration_sensor_offset: Chain[2] chip[40] use PIC middle temp offset=-4, typeID=55 2020-02-14 09:09:39 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[2] Chip[40] local:0 remote:0 offset:-4 2020-02-14 09:09:39 temperature.c:870:calibration_sensor_offset: Chain[2] Chip[40] get middle temp offset=-4 typeID=55 2020-02-14 09:09:39 asic.c:1153:set_baud: set baud=1 2020-02-14 09:09:39 asic.c:1126:set_baud_one_chain: cmd_buf[0]=0x51090018, cmd_buf[1]=0x2101, cmd_buf[2]=0x11000000, misc=0x2101 2020-02-14 09:09:39 asic.c:1126:set_baud_one_chain: cmd_buf[0]=0x51090018, cmd_buf[1]=0x2101, cmd_buf[2]=0x11000000, misc=0x2101 2020-02-14 09:09:39 asic.c:1126:set_baud_one_chain: cmd_buf[0]=0x51090018, cmd_buf[1]=0x2101, cmd_buf[2]=0x11000000, misc=0x2101 2020-02-14 09:09:39 asic.c:1164:set_baud: read bc write is 0x82001a 2020-02-14 09:09:39 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x6161, cmd_buf[2]=0x13000000, misc=0x6161 2020-02-14 09:09:39 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x6161, cmd_buf[2]=0x1a000000, misc=0x6161 2020-02-14 09:09:39 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x6161, cmd_buf[2]=0x13000000, misc=0x6161 2020-02-14 09:09:39 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x6161, cmd_buf[2]=0x1a000000, misc=0x6161 2020-02-14 09:09:39 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x6161, cmd_buf[2]=0x13000000, misc=0x6161 2020-02-14 09:09:39 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x6161, cmd_buf[2]=0x1a000000, misc=0x6161 2020-02-14 09:09:39 driver-btm-soc.c:6509:bitmain_soc_init: set TICKET_MASK 2020-02-14 09:09:41 temperature.c:2081:detect_startup_environment_temperature: Environment temperature: [30] 2020-02-14 09:09:41 temperature.c:2098:detect_startup_environment_temperature: Enter 10 secs to cool down hash board, 1 times ... 2020-02-14 09:09:52 temperature.c:2081:detect_startup_environment_temperature: Environment temperature: [29] 2020-02-14 09:09:52 temperature.c:2098:detect_startup_environment_temperature: Enter 10 secs to cool down hash board, 2 times ... 2020-02-14 09:10:03 temperature.c:2081:detect_startup_environment_temperature: Environment temperature: [29] 2020-02-14 09:10:03 temperature.c:2098:detect_startup_environment_temperature: Enter 10 secs to cool down hash board, 3 times ... 2020-02-14 09:10:13 driver-btm-soc.c:3884:set_clock_delay_control: set mode 0 2020-02-14 09:10:13 driver-btm-soc.c:3903:set_clock_delay_control: core_data = 0x04 2020-02-14 09:10:13 driver-btm-soc.c:3974:open_core_bm1393: Start Open Core!! 2020-02-14 09:10:19 driver-btm-soc.c:4041:open_core_bm1393: End Open Core!! 2020-02-14 09:10:20 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 125 2020-02-14 09:10:22 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 150 2020-02-14 09:10:24 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 175 2020-02-14 09:10:27 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 200 2020-02-14 09:10:29 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 225 2020-02-14 09:10:31 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 250 2020-02-14 09:10:33 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 275 2020-02-14 09:10:35 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 300 2020-02-14 09:10:37 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 325 2020-02-14 09:10:39 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 350 2020-02-14 09:10:42 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 375 2020-02-14 09:10:44 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 385 2020-02-14 09:10:46 driver-btm-soc.c:5209:increase_freq_by_eeprom_slowly: max = 385 ,min = 385 2020-02-14 09:10:46 driver-btm-soc.c:5215:increase_freq_by_eeprom_slowly: chain[0] increaseing the diff freq ... 2020-02-14 09:10:46 driver-btm-soc.c:5243:increase_freq_by_eeprom_slowly: chain 0 final freq setting: 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 2020-02-14 09:10:46 driver-btm-soc.c:5255:increase_freq_by_eeprom_slowly: set chain 0 to working voltage 2020-02-14 09:10:46 power.c:1309:slowly_set_working_power_t11: set chain 0 to working voltage: now setting chain[0]-volt[10.20]-data[026] now setting chain[0]-volt[10.17]-data[027] now setting chain[0]-volt[10.14]-data[028] now setting chain[0]-volt[10.11]-data[029] 2020-02-14 09:11:01 dspic33ep16gs202.c:213:dsPIC33EP16GS202_pic_heart_beat: ERROR! failed on Chain[0] after 3 times try! now setting chain[0]-volt[10.08]-data[030] now setting chain[0]-volt[10.02]-data[032] now setting chain[0]-volt[09.97]-data[034] now setting chain[0]-volt[09.95]-data[035] now setting chain[0]-volt[09.92]-data[036] 2020-02-14 09:11:22 power.c:1331:slowly_set_working_power_t11: done! 2020-02-14 09:11:22 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 125 2020-02-14 09:11:24 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 150 2020-02-14 09:11:26 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 175 2020-02-14 09:11:28 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 200 2020-02-14 09:11:31 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 225 2020-02-14 09:11:33 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 250 2020-02-14 09:11:35 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 275 2020-02-14 09:11:37 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 300 2020-02-14 09:11:39 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 325 2020-02-14 09:11:41 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 350 2020-02-14 09:11:43 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 375 2020-02-14 09:11:46 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 385 2020-02-14 09:11:48 driver-btm-soc.c:5209:increase_freq_by_eeprom_slowly: max = 385 ,min = 385 2020-02-14 09:11:48 driver-btm-soc.c:5215:increase_freq_by_eeprom_slowly: chain[1] increaseing the diff freq ... 2020-02-14 09:11:48 driver-btm-soc.c:5243:increase_freq_by_eeprom_slowly: chain 1 final freq setting: 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 2020-02-14 09:11:48 driver-btm-soc.c:5255:increase_freq_by_eeprom_slowly: set chain 1 to working voltage 2020-02-14 09:11:48 power.c:1309:slowly_set_working_power_t11: set chain 1 to working voltage: now setting chain[1]-volt[10.20]-data[026] now setting chain[1]-volt[10.17]-data[027] now setting chain[1]-volt[10.14]-data[028] now setting chain[1]-volt[10.11]-data[029] now setting chain[1]-volt[10.08]-data[030] now setting chain[1]-volt[10.02]-data[032] now setting chain[1]-volt[09.97]-data[034] now setting chain[1]-volt[09.95]-data[035] now setting chain[1]-volt[09.92]-data[036] 2020-02-14 09:12:23 power.c:1331:slowly_set_working_power_t11: done! 2020-02-14 09:12:23 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 125 2020-02-14 09:12:25 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 150 2020-02-14 09:12:27 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 175 2020-02-14 09:12:30 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 200 2020-02-14 09:12:32 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 225 2020-02-14 09:12:34 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 250 2020-02-14 09:12:36 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 275 2020-02-14 09:12:38 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 300 2020-02-14 09:12:40 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 325 2020-02-14 09:12:42 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 350 2020-02-14 09:12:45 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 375 2020-02-14 09:12:47 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 385 2020-02-14 09:12:49 driver-btm-soc.c:5209:increase_freq_by_eeprom_slowly: max = 385 ,min = 385 2020-02-14 09:12:49 driver-btm-soc.c:5215:increase_freq_by_eeprom_slowly: chain[2] increaseing the diff freq ... 2020-02-14 09:12:49 driver-btm-soc.c:5243:increase_freq_by_eeprom_slowly: chain 2 final freq setting: 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 385 2020-02-14 09:12:49 driver-btm-soc.c:5255:increase_freq_by_eeprom_slowly: set chain 2 to working voltage 2020-02-14 09:12:49 power.c:1309:slowly_set_working_power_t11: set chain 2 to working voltage: now setting chain[2]-volt[10.20]-data[026] now setting chain[2]-volt[10.17]-data[027] now setting chain[2]-volt[10.14]-data[028] now setting chain[2]-volt[10.11]-data[029] now setting 2020-02-14 09:13:07 dspic33ep16gs202.c:276:dsPIC33EP16GS202_set_pic_voltage: ERROR! failed on Chain[2] after 3 times try! chain[2]-volt[10.08]-data[030] now setting chain[2]-volt[10.02]-data[032] now setting chain[2]-volt[09.97]-data[034] now setting 2020-02-14 09:13:19 dspic33ep16gs202.c:276:dsPIC33EP16GS202_set_pic_voltage: ERROR! failed on Chain[2] after 3 times try! chain[2]-volt[09.95]-data[035] now setting chain[2]-volt[09.92]-data[036] 2020-02-14 09:13:23 power.c:1331:slowly_set_working_power_t11: done! 2020-02-14 09:13:23 driver-btm-soc.c:6545:bitmain_soc_init: set to working voltage... 2020-02-14 09:13:23 power.c:1258:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage: now setting chain[0]-volt[09.92]-data[036] chain[1]-volt[09.92]-data[036] chain[2]-volt[09.92]-data[036] 2020-02-14 09:13:26 power.c:1278:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage end! now setting chain[0]-volt[09.90]-data[036] chain[1]-volt[09.90]-data[036] chain[2]-volt[09.90]-data[036] 2020-02-14 09:13:26 driver-btm-soc.c:4929:set_timeout: freq 385 final timeout=340 2020-02-14 09:13:26 driver-btm-soc.c:2925:low_temp_process_parm_init: chip miner_type = [0] 2020-02-14 09:13:26 driver-btm-soc.c:2925:low_temp_process_parm_init: chip miner_type = [0] 2020-02-14 09:13:26 driver-btm-soc.c:2925:low_temp_process_parm_init: chip miner_type = [0] 2020-02-14 09:13:26 driver-btm-soc.c:3539:check_system_work: check system thread start... 2020-02-14 09:13:26 driver-btm-soc.c:6614:bitmain_soc_init: Init done! 2020-02-14 09:13:26 driver-btm-soc.c:7257:bitmain_soc_prepare: bitmain soc init success. 2020-02-14 09:13:27 temperature.c:1542:read_temp_func: bring_up_pcb_temp = 35 2020-02-14 09:13:45 temperature.c:1887:get_target_chip_temp: if startup in low temp environment: NO 2020-02-14 09:13:45 temperature.c:1733:_get_target_chip_temp_t11: chip miner_type = [0] 2020-02-14 09:13:45 temperature.c:1733:_get_target_chip_temp_t11: chip miner_type = [0] 2020-02-14 09:13:45 temperature.c:1733:_get_target_chip_temp_t11: chip miner_type = [0] 2020-02-14 09:15:30 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:15:34 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:15:39 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:15:43 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:15:48 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:15:53 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:15:57 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:02 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:06 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:11 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:15 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:20 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:24 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:29 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:34 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:38 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:43 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:47 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:52 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:16:56 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:17:01 temperature.c:1363:process_status_value: Fatal Error: network connection lost! 2020-02-14 09:17:05 temperature.c:1363:process_status_value: Fatal Error: network connection lost!
|