T17 will not hold hashrate

[TonyGotaTruck]

Picked up 3 - T17`s. My Internet speed is 198meg. Runs up to almost 40 Hashrate then over next hour it drops slowly. It will go back up a small amount but, continues on downward. It went to 18.58 and at 24.15 now.

Very cool weather here right now. Just checked and temperature in the room is 80 degrees.

I am new to this and I don't understand a lot. I have been watching youtubes and reading but, cant understand why I cant keep 40plus hashrate.

Update... I use a Charter Spectrum Modem (Arris) with a Netgear NightHawk R7000 Router (just upgraded software) and from there I am Cat5 to the T17.

The router took off with blazing speeds and I got 69 hashrate, soon, 45, then 35, now 23.22....

I think it is my cable TV wire. I just realized its 26 years old. Installed before we ever used Internet over cable. Will replace it tomorrow.

Any advise or direction would be helpful.

Alabama USA

[BitMaxz]

Very cool weather here right now. Just checked and temperature in the room is 80 degrees.

80 degrees Fahrenheit or Celsius? I guess it's Fahrenheit.

Much better put the kernel logs here and the screenshot of the miner status.

Maybe we can find the issue under your kernel logs.

It might be a PSU issue, Hashboard(ASIC chip is Damaged) or Pool issue(High ping).

[mikeywith]

You mentioned all the details but missed out one crucial element which is WHERE does the hashrate fluctuate?  is it stable at 40-42th on the miner's status page but goes below on the mining pool side? or is it on the miner itself or both?

Please answer that question and provide the following:

1- Screenshots of the miner status page + the pool status
2- Copy paste the kernel log of the miner, use the code format

Code:

Paste the kernel log here

In general this usually an 'easy to fix' problem, I will take you to step by step to fix this "hopefully", meanwhile you can  this and this.

80 degrees Fahrenheit or Celsius? I guess it's Fahrenheit.

Seriously dude we as non-us-citizens should start demanding that people write temps in Celsius scale. When I read 80 degrees I thought it was a toaster at first.  

[philipma1957]

I suppose you will be demanding

meters and klicks vs yards and miles. 😄. no way

personally we should all be using kelvin scale for temp.

80 would be super fucking cold.
as 0 is the start of the scale no negatives at all.

to op my answer to your poll is maybe.

please post logs I will read and attempt to help you.

do you use a switch to access router.
is so what is the switch
is it 100 mb or gig speed switch.
an eight port
or 16
or 32
or 48

[mikeywith]

meters and klicks vs yards and miles. 😄. no way

It's orange vs gray   if the "grey" people stop answering any questions that have Fahrenheit in them, I bet many will go unanswered   , that was a lame joke anyway, while I prefer to see Celsius so that I don't have to use google for that, but that won't stop me from helping here.

personally we should all be using kelvin scale for temp.

I hardly understand F let alone K.  

do you use a switch to access router.

My initial guess is that his router is somehow dropping packets from itself to the pool, and that his miner's status page shows perfect reading but the pool doesn't, however, I don't want to jump to conclusions.

[TonyGotaTruck]

80 degrees Fahrenheit or Celsius? I guess it's Fahrenheit.

Much better put the kernel logs here and the screenshot of the miner status.

Maybe we can find the issue under your kernel logs.

It might be a PSU issue, Hashboard(ASIC chip is Damaged) or Pool issue(High ping).

The 80 is Fahreheit.

I do not know how to copy paste logs etc. The only info I have is from my Antpool account. How may I access Kernel Logs?

[philipma1957]

open the gui  look at tabs click  kernel log



then copy the log paste it here

[philipma1957]

my machine has been running for over 2 weeks so my log is long

section 1 fits on this post.

Code:

Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 195352K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 34024K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 20984K (cc682000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 7/3, WL threshold: 4096, image sequence number: 4244297529
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 01559AD8-7B6A-42E6-A3FE-EDF3659527A9, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 529/159, WL threshold: 4096, image sequence number: 4185749592
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 4829CF2C-7435-4146-B2FD-0826AAE8443A, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
macb e000b000.ethernet eth0: link down
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab011
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
macb e000b000.ethernet eth0: link down
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
random: nonblocking pool is initialized
 [1970-01-01 00:00:53.350] httpListenThread start ret=0
 [1970-01-01 00:01:23.352] start listen on 6060 ...
 [1970-01-01 00:05:58.629] set_start_time_point total_tv_start_sys=359 total_tv_end_sys=360

1970-01-01 00:00:53 driver-btm-soc.c:3297:init_freq_mode: This is scan-user version
1970-01-01 00:00:53 driver-btm-soc.c:4118:bitmain_soc_init: opt_multi_version=1
1970-01-01 00:00:53 driver-btm-soc.c:4119:bitmain_soc_init: opt_bitmain_ab=1
1970-01-01 00:00:53 driver-btm-soc.c:4120:bitmain_soc_init: opt_bitmain_work_mode=0
1970-01-01 00:00:53 driver-btm-soc.c:3658:_show_sn: no SN got, please write SN to /nvdata/sn
1970-01-01 00:00:53 driver-btm-soc.c:3328:init_phy_mem_nonce2_jobid_address: Detect 256MB control board of XILINX
1970-01-01 00:00:53 driver-btm-soc.c:4126:bitmain_soc_init: Miner compile time: Fri May 24 21:07:07 CST 2019
1970-01-01 00:00:53 driver-btm-soc.c:4128:bitmain_soc_init: last commit version: c416f93 commit time: 2019-05-24 21:03:40 build: 2019-05-24 21:14:44
1970-01-01 00:00:53 driver-btm-soc.c:3360:check_fan_multi: check fan for 20 times...
1970-01-01 00:00:55 driver-btm-soc.c:3436:init_miner_version: miner ID : 81620d025c208854
1970-01-01 00:00:55 driver-btm-soc.c:3442:init_miner_version: FPGA Version = 0xB011
1970-01-01 00:00:55 driver-btm-soc.c:405:check_chain: !! chain[0]is exist
1970-01-01 00:00:55 driver-btm-soc.c:405:check_chain: !! chain[1]is exist
1970-01-01 00:00:55 driver-btm-soc.c:405:check_chain: !! chain[2]is exist
1970-01-01 00:00:59 driver-btm-soc.c:3864:get_product_id: product_id[0] = 1
1970-01-01 00:00:59 driver-btm-soc.c:3864:get_product_id: product_id[1] = 1
1970-01-01 00:00:59 driver-btm-soc.c:3864:get_product_id: product_id[2] = 1
1970-01-01 00:00:59 driver-btm-soc.c:4032:bitmain_board_init: g_product_id = 1
1970-01-01 00:00:59 driver-btm-soc.c:3900:get_ccdly_opt: ccdly_opt[0] = 1
1970-01-01 00:00:59 driver-btm-soc.c:3900:get_ccdly_opt: ccdly_opt[1] = 1
1970-01-01 00:00:59 driver-btm-soc.c:3900:get_ccdly_opt: ccdly_opt[2] = 1
1970-01-01 00:00:59 driver-btm-soc.c:4041:bitmain_board_init: g_ccdly_opt = 1
1970-01-01 00:00:59 driver-btm-soc.c:3716:_set_project_type: Project type: Antminer T17
1970-01-01 00:00:59 driver-btm-soc.c:3458:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
1970-01-01 00:00:59 driver-btm-soc.c:3459:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
1970-01-01 00:00:59 driver-btm-soc.c:3458:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
1970-01-01 00:00:59 driver-btm-soc.c:3459:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
1970-01-01 00:00:59 driver-btm-soc.c:3458:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
1970-01-01 00:00:59 driver-btm-soc.c:3459:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
1970-01-01 00:01:00 pic.c:619:pic_reset: chain[0] ok
1970-01-01 00:01:04 pic.c:898:jump_to_app_from_loader: chain[0] ok
1970-01-01 00:01:05 pic.c:619:pic_reset: chain[1] ok
1970-01-01 00:01:09 pic.c:898:jump_to_app_from_loader: chain[1] ok
1970-01-01 00:01:10 pic.c:619:pic_reset: chain[2] ok
1970-01-01 00:01:14 pic.c:898:jump_to_app_from_loader: chain[2] ok
1970-01-01 00:01:14 driver-btm-soc.c:4062:bitmain_board_init: Enter 30s sleep to make sure power release finish.
1970-01-01 00:01:14 driver-btm-soc.c:1177:heart_beat_func_one_chain: for chain 2
1970-01-01 00:01:14 driver-btm-soc.c:1177:heart_beat_func_one_chain: for chain 1
1970-01-01 00:01:14 driver-btm-soc.c:1177:heart_beat_func_one_chain: for chain 0
1970-01-01 00:01:44 power.c:187:power_init: power init ... 
1970-01-01 00:01:44 power.c:177:power_check_protocol_type: power type APW9 3600W
1970-01-01 00:01:44 power.c:154:power_on: init gpio907
1970-01-01 00:01:45 power.c:643:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
1970-01-01 00:01:47 power.c:251:check_voltage_multi: retry time: 0
1970-01-01 00:01:48 power.c:213:get_average_voltage: chain[0], voltage is: 20.487715 
1970-01-01 00:01:48 power.c:213:get_average_voltage: chain[1], voltage is: 20.279531 
1970-01-01 00:01:49 power.c:213:get_average_voltage: chain[2], voltage is: 19.936640 
1970-01-01 00:01:49 power.c:224:get_average_voltage: aveage voltage is: 20.234629 
1970-01-01 00:01:49 power.c:237:check_voltage: target_vol = 17.00, actural_vol = 20.23, more than 0.5v diff.
1970-01-01 00:01:50 power.c:251:check_voltage_multi: retry time: 1
1970-01-01 00:01:51 power.c:213:get_average_voltage: chain[0], voltage is: 19.152890 
1970-01-01 00:01:52 power.c:213:get_average_voltage: chain[1], voltage is: 19.005937 
1970-01-01 00:01:52 power.c:213:get_average_voltage: chain[2], voltage is: 18.705908 
1970-01-01 00:01:52 power.c:224:get_average_voltage: aveage voltage is: 18.954912 
1970-01-01 00:01:52 power.c:237:check_voltage: target_vol = 17.00, actural_vol = 18.95, more than 0.5v diff.
1970-01-01 00:01:53 power.c:251:check_voltage_multi: retry time: 2
1970-01-01 00:01:54 power.c:213:get_average_voltage: chain[0], voltage is: 18.265049 
1970-01-01 00:01:54 power.c:213:get_average_voltage: chain[1], voltage is: 18.093603 
1970-01-01 00:01:55 power.c:213:get_average_voltage: chain[2], voltage is: 17.818066 
1970-01-01 00:01:55 power.c:224:get_average_voltage: aveage voltage is: 18.058906 
1970-01-01 00:01:55 power.c:237:check_voltage: target_vol = 17.00, actural_vol = 18.06, more than 0.5v diff.
1970-01-01 00:01:56 power.c:251:check_voltage_multi: retry time: 3
1970-01-01 00:01:56 power.c:213:get_average_voltage: chain[0], voltage is: 17.395576 
1970-01-01 00:01:57 power.c:213:get_average_voltage: chain[1], voltage is: 17.254746 
1970-01-01 00:01:58 power.c:213:get_average_voltage: chain[2], voltage is: 17.003701 
1970-01-01 00:01:58 power.c:224:get_average_voltage: aveage voltage is: 17.218008 
1970-01-01 00:01:58 power.c:593:set_iic_power_by_voltage: now set voltage to : 17.000000 
1970-01-01 00:01:58 zynq.c:192:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
1970-01-01 00:02:02 pic.c:234:hashboard_power_cntl: [1] ok, i2c=0!
1970-01-01 00:02:02 zynq.c:192:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
1970-01-01 00:02:06 driver-btm-soc.c:3799:check_asic_number_with_power_on: Chain[0]: find 9 asic, times 0
1970-01-01 00:02:06 zynq.c:192:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
1970-01-01 00:02:10 pic.c:234:hashboard_power_cntl: [1] ok, i2c=0!
1970-01-01 00:02:10 zynq.c:192:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
1970-01-01 00:02:14 driver-btm-soc.c:3799:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 1
1970-01-01 00:02:14 zynq.c:192:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
1970-01-01 00:02:17 pic.c:234:hashboard_power_cntl: [1] ok, i2c=1!
1970-01-01 00:02:17 zynq.c:192:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
1970-01-01 00:02:21 driver-btm-soc.c:3799:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
1970-01-01 00:02:21 zynq.c:192:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
1970-01-01 00:02:24 pic.c:234:hashboard_power_cntl: [1] ok, i2c=2!
1970-01-01 00:02:24 zynq.c:192:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
1970-01-01 00:02:28 driver-btm-soc.c:3799:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
1970-01-01 00:02:28 chip139x.c:738:set_order_clock: chain[0]: set order clock, stragegy 3
1970-01-01 00:02:28 chip139x.c:738:set_order_clock: chain[1]: set order clock, stragegy 3
1970-01-01 00:02:28 chip139x.c:738:set_order_clock: chain[2]: set order clock, stragegy 3
1970-01-01 00:02:34 chip139x.c:848:set_core_clock_delay_control: pwth_sel = 3, ccdly_sel = 2
1970-01-01 00:02:34 chip139x.c:863:set_core_clock_delay_control: set CLOCK_DELAY_CTRL to 0xb4
voltage[0] = 1730
voltage[1] = 1730
voltage[2] = 1730
1970-01-01 00:02:34 power.c:267:set_working_voltage: working_voltage = 17.300000
sensor type = 1,sensor num = 4
sensor pos: 9  7  22  24  0  0  0  0 
sensor offset: 0  0  0  0  0  0  0  0 
1970-01-01 00:02:34 temperature.c:356:calibration_sensor_offset: chain[0] temp chip I2C addr=0x98
1970-01-01 00:02:34 temperature.c:420:calibration_sensor_offset: Chain[0] chip[8] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:34 temperature.c:420:calibration_sensor_offset: Chain[0] chip[6] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:35 temperature.c:420:calibration_sensor_offset: Chain[0] chip[21] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:35 temperature.c:420:calibration_sensor_offset: Chain[0] chip[23] use PIC middle temp offset=0, typeID=55
sensor type = 1,sensor num = 4
sensor pos: 9  7  22  24  0  0  0  0 
sensor offset: 0  0  0  0  0  0  0  0 
1970-01-01 00:02:35 temperature.c:356:calibration_sensor_offset: chain[1] temp chip I2C addr=0x98
1970-01-01 00:02:35 temperature.c:420:calibration_sensor_offset: Chain[1] chip[8] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:36 temperature.c:420:calibration_sensor_offset: Chain[1] chip[6] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:36 temperature.c:420:calibration_sensor_offset: Chain[1] chip[21] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:36 temperature.c:420:calibration_sensor_offset: Chain[1] chip[23] use PIC middle temp offset=0, typeID=55
sensor type = 1,sensor num = 4
sensor pos: 9  7  22  24  0  0  0  0 
sensor offset: 0  0  0  0  0  0  0  0 
1970-01-01 00:02:36 temperature.c:356:calibration_sensor_offset: chain[2] temp chip I2C addr=0x98
1970-01-01 00:02:37 temperature.c:420:calibration_sensor_offset: Chain[2] chip[8] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:37 temperature.c:420:calibration_sensor_offset: Chain[2] chip[6] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:38 temperature.c:420:calibration_sensor_offset: Chain[2] chip[21] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:38 temperature.c:420:calibration_sensor_offset: Chain[2] chip[23] use PIC middle temp offset=0, typeID=55
1970-01-01 00:02:40 temperature.c:446:do_calibration_temperature_sensor: bring up lowest temperature is 27
1970-01-01 00:02:40 chip139x.c:320:set_baud_one_chain: chain[0]: chip baud = 6000000, chip_divider = 7
1970-01-01 00:02:40 chip139x.c:320:set_baud_one_chain: chain[1]: chip baud = 6000000, chip_divider = 7
1970-01-01 00:02:40 chip139x.c:320:set_baud_one_chain: chain[2]: chip baud = 6000000, chip_divider = 7
1970-01-01 00:02:40 chip139x.c:277:set_baud_fpga: set fpga_baud = 6000000, fpga_divider = 3
1970-01-01 00:02:40 driver-btm-soc.c:3477:calculate_timeout: dev->timeout = 392
1970-01-01 00:02:40 freq_tuning.c:254:freq_tuning_get_max_freq: Max freq of tuning is 740
1970-01-01 00:02:40 driver-btm-soc.c:3207:increase_freq_by_frequency_list_slowly: Increase freq slowly for all chain to 640
1970-01-01 00:02:40 temperature.c:1379:get_current_lowest_temperature: current lowest temperature is 27
1970-01-01 00:02:40 driver-btm-soc.c:2890:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 50.000000 to 600.000000 @18.00V.
1970-01-01 00:02:40 driver-btm-soc.c:2891:auto_adaption_high_voltage_increase_frequency: index 0 2
1970-01-01 00:02:40 power.c:790:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
1970-01-01 00:02:40 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[150] = 17.174282
1970-01-01 00:02:41 temperature.c:1043:read_temp_func: bring_up_pcb_temp = 27
1970-01-01 00:02:41 temperature.c:1072:read_temp_func: PCB low 27, high 28. CHIP low 29, high 31
1970-01-01 00:02:42 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[144] = 17.341724
1970-01-01 00:02:44 temperature.c:1072:read_temp_func: PCB low 27, high 28. CHIP low 29, high 31
1970-01-01 00:02:45 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[138] = 17.509166
1970-01-01 00:02:47 temperature.c:1072:read_temp_func: PCB low 27, high 28. CHIP low 29, high 31
1970-01-01 00:02:48 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[132] = 17.676608
1970-01-01 00:02:49 temperature.c:1072:read_temp_func: PCB low 27, high 28. CHIP low 30, high 31
1970-01-01 00:02:50 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[126] = 17.844049
1970-01-01 00:02:52 temperature.c:1072:read_temp_func: PCB low 28, high 28. CHIP low 30, high 31
1970-01-01 00:02:53 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[124] = 17.899863
1970-01-01 00:02:55 temperature.c:1072:read_temp_func: PCB low 28, high 29. CHIP low 30, high 32
1970-01-01 00:02:56 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[122] = 17.955677
1970-01-01 00:02:58 temperature.c:1072:read_temp_func: PCB low 28, high 29. CHIP low 30, high 32
1970-01-01 00:02:58 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[121] = 17.983584
1970-01-01 00:03:00 temperature.c:1072:read_temp_func: PCB low 28, high 29. CHIP low 30, high 32
1970-01-01 00:03:01 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[120] = 18.011491
1970-01-01 00:03:03 temperature.c:1072:read_temp_func: PCB low 28, high 29. CHIP low 30, high 32
1970-01-01 00:03:03 power.c:251:check_voltage_multi: retry time: 0
1970-01-01 00:03:04 power.c:213:get_average_voltage: chain[0], voltage is: 18.032373 
1970-01-01 00:03:05 power.c:213:get_average_voltage: chain[1], voltage is: 18.075234 
1970-01-01 00:03:06 power.c:213:get_average_voltage: chain[2], voltage is: 17.989511 
1970-01-01 00:03:06 power.c:224:get_average_voltage: aveage voltage is: 18.032373 
1970-01-01 00:03:06 driver-btm-soc.c:2845:increase_freq_slowly: init_freq = 50.00, final_freq = 600.00, freq_step = 5.00, chain = 255
1970-01-01 00:03:06 temperature.c:1072:read_temp_func: PCB low 28, high 29. CHIP low 30, high 32
1970-01-01 00:03:08 temperature.c:1072:read_temp_func: PCB low 28, high 29. CHIP low 30, high 33
1970-01-01 00:03:11 temperature.c:1072:read_temp_func: PCB low 28, high 29. CHIP low 31, high 33
1970-01-01 00:03:14 temperature.c:1072:read_temp_func: PCB low 29, high 29. CHIP low 31, high 34
1970-01-01 00:03:16 temperature.c:1072:read_temp_func: PCB low 29, high 29. CHIP low 32, high 34
1970-01-01 00:03:19 temperature.c:1072:read_temp_func: PCB low 29, high 30. CHIP low 33, high 35
1970-01-01 00:03:22 temperature.c:1072:read_temp_func: PCB low 29, high 30. CHIP low 33, high 35
1970-01-01 00:03:24 temperature.c:1072:read_temp_func: PCB low 29, high 30. CHIP low 34, high 36
1970-01-01 00:03:27 temperature.c:1072:read_temp_func: PCB low 30, high 30. CHIP low 35, high 37
1970-01-01 00:03:30 temperature.c:1072:read_temp_func: PCB low 30, high 31. CHIP low 36, high 38
1970-01-01 00:03:32 temperature.c:1072:read_temp_func: PCB low 30, high 31. CHIP low 37, high 39
1970-01-01 00:03:35 temperature.c:1072:read_temp_func: PCB low 30, high 31. CHIP low 37, high 40
1970-01-01 00:03:38 temperature.c:1072:read_temp_func: PCB low 31, high 32. CHIP low 38, high 40
1970-01-01 00:03:41 temperature.c:1072:read_temp_func: PCB low 31, high 32. CHIP low 39, high 41
1970-01-01 00:03:43 temperature.c:1072:read_temp_func: PCB low 31, high 32. CHIP low 40, high 42
1970-01-01 00:03:46 temperature.c:1072:read_temp_func: PCB low 31, high 33. CHIP low 40, high 43
1970-01-01 00:03:49 temperature.c:1072:read_temp_func: PCB low 32, high 33. CHIP low 41, high 44
1970-01-01 00:03:51 temperature.c:1072:read_temp_func: PCB low 32, high 33. CHIP low 42, high 45
1970-01-01 00:03:54 temperature.c:1072:read_temp_func: PCB low 33, high 34. CHIP low 43, high 46
1970-01-01 00:03:57 temperature.c:1072:read_temp_func: PCB low 33, high 34. CHIP low 44, high 46
1970-01-01 00:03:59 temperature.c:1072:read_temp_func: PCB low 33, high 35. CHIP low 44, high 48
1970-01-01 00:04:02 temperature.c:1072:read_temp_func: PCB low 33, high 35. CHIP low 45, high 48
1970-01-01 00:04:05 temperature.c:1072:read_temp_func: PCB low 34, high 36. CHIP low 46, high 49
1970-01-01 00:04:07 temperature.c:1072:read_temp_func: PCB low 34, high 36. CHIP low 47, high 51
1970-01-01 00:04:10 temperature.c:1072:read_temp_func: PCB low 35, high 37. CHIP low 48, high 52
1970-01-01 00:04:13 temperature.c:1072:read_temp_func: PCB low 35, high 37. CHIP low 49, high 53
1970-01-01 00:04:16 temperature.c:1072:read_temp_func: PCB low 36, high 38. CHIP low 50, high 54
1970-01-01 00:04:18 temperature.c:1072:read_temp_func: PCB low 36, high 38. CHIP low 51, high 55
1970-01-01 00:04:21 temperature.c:1072:read_temp_func: PCB low 37, high 39. CHIP low 52, high 56
1970-01-01 00:04:24 temperature.c:1072:read_temp_func: PCB low 37, high 39. CHIP low 53, high 57
1970-01-01 00:04:26 temperature.c:1072:read_temp_func: PCB low 37, high 40. CHIP low 54, high 58
1970-01-01 00:04:29 temperature.c:1072:read_temp_func: PCB low 38, high 40. CHIP low 54, high 58
1970-01-01 00:04:32 temperature.c:1072:read_temp_func: PCB low 38, high 40. CHIP low 55, high 60
1970-01-01 00:04:34 temperature.c:1072:read_temp_func: PCB low 38, high 41. CHIP low 56, high 61
1970-01-01 00:04:37 temperature.c:1072:read_temp_func: PCB low 39, high 41. CHIP low 57, high 62
1970-01-01 00:04:40 temperature.c:1072:read_temp_func: PCB low 39, high 42. CHIP low 58, high 63
1970-01-01 00:04:42 temperature.c:1072:read_temp_func: PCB low 39, high 42. CHIP low 59, high 64
1970-01-01 00:04:45 temperature.c:1072:read_temp_func: PCB low 40, high 43. CHIP low 60, high 65
1970-01-01 00:04:48 temperature.c:1072:read_temp_func: PCB low 40, high 43. CHIP low 60, high 66
1970-01-01 00:04:51 temperature.c:1072:read_temp_func: PCB low 40, high 44. CHIP low 61, high 67
1970-01-01 00:04:53 temperature.c:1072:read_temp_func: PCB low 41, high 44. CHIP low 62, high 68
1970-01-01 00:04:56 temperature.c:1072:read_temp_func: PCB low 41, high 45. CHIP low 63, high 69
1970-01-01 00:04:57 temperature.c:1379:get_current_lowest_temperature: current lowest temperature is 41
1970-01-01 00:04:57 driver-btm-soc.c:2890:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 600.000000 to 640.000000 @17.80V.
1970-01-01 00:04:57 driver-btm-soc.c:2891:auto_adaption_high_voltage_increase_frequency: index 1 3
1970-01-01 00:04:57 power.c:790:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.80 ...
1970-01-01 00:04:57 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[121] = 17.983584
1970-01-01 00:04:59 temperature.c:1072:read_temp_func: PCB low 42, high 46. CHIP low 64, high 70
1970-01-01 00:05:00 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[122] = 17.955677
1970-01-01 00:05:01 temperature.c:1072:read_temp_func: PCB low 42, high 46. CHIP low 64, high 70
1970-01-01 00:05:03 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[123] = 17.927770
1970-01-01 00:05:04 temperature.c:1072:read_temp_func: PCB low 42, high 47. CHIP low 64, high 71
1970-01-01 00:05:05 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[124] = 17.899863
1970-01-01 00:05:07 temperature.c:1072:read_temp_func: PCB low 43, high 47. CHIP low 64, high 71
1970-01-01 00:05:08 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[125] = 17.871956
1970-01-01 00:05:09 temperature.c:1072:read_temp_func: PCB low 43, high 47. CHIP low 64, high 72
1970-01-01 00:05:10 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[126] = 17.844049
1970-01-01 00:05:12 temperature.c:1072:read_temp_func: PCB low 43, high 48. CHIP low 64, high 72
1970-01-01 00:05:13 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[127] = 17.816142
1970-01-01 00:05:15 temperature.c:1072:read_temp_func: PCB low 43, high 48. CHIP low 64, high 72
1970-01-01 00:05:16 power.c:251:check_voltage_multi: retry time: 0
1970-01-01 00:05:16 power.c:213:get_average_voltage: chain[0], voltage is: 17.811943 
1970-01-01 00:05:17 power.c:213:get_average_voltage: chain[1], voltage is: 17.848681 
1970-01-01 00:05:17 power.c:213:get_average_voltage: chain[2], voltage is: 17.744590 
1970-01-01 00:05:17 power.c:224:get_average_voltage: aveage voltage is: 17.801738 
1970-01-01 00:05:17 driver-btm-soc.c:2845:increase_freq_slowly: init_freq = 600.00, final_freq = 640.00, freq_step = 5.00, chain = 255
1970-01-01 00:05:17 temperature.c:1072:read_temp_func: PCB low 43, high 48. CHIP low 64, high 73
1970-01-01 00:05:20 temperature.c:1072:read_temp_func: PCB low 43, high 49. CHIP low 65, high 73
1970-01-01 00:05:23 temperature.c:1072:read_temp_func: PCB low 44, high 49. CHIP low 65, high 74
1970-01-01 00:05:25 driver-btm-soc.c:3219:increase_freq_by_frequency_list_slowly: Increase freq slowly for chain 0 to 670
1970-01-01 00:05:25 temperature.c:1379:get_current_lowest_temperature: current lowest temperature is 44
1970-01-01 00:05:25 driver-btm-soc.c:2890:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 640.000000 to 650.000000 @17.80V.
1970-01-01 00:05:25 driver-btm-soc.c:2891:auto_adaption_high_voltage_increase_frequency: index 1 3
1970-01-01 00:05:25 driver-btm-soc.c:2845:increase_freq_slowly: init_freq = 640.00, final_freq = 650.00, freq_step = 5.00, chain = 0
1970-01-01 00:05:25 temperature.c:1072:read_temp_func: PCB low 44, high 49. CHIP low 66, high 74
1970-01-01 00:05:27 temperature.c:1379:get_current_lowest_temperature: current lowest temperature is 44
1970-01-01 00:05:27 driver-btm-soc.c:2890:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 650.000000 to 670.000000 @17.80V.
1970-01-01 00:05:27 driver-btm-soc.c:2891:auto_adaption_high_voltage_increase_frequency: index 2 3
1970-01-01 00:05:27 driver-btm-soc.c:2845:increase_freq_slowly: init_freq = 650.00, final_freq = 670.00, freq_step = 5.00, chain = 0
1970-01-01 00:05:28 temperature.c:1072:read_temp_func: PCB low 44, high 49. CHIP low 66, high 75
1970-01-01 00:05:31 temperature.c:1072:read_temp_func: PCB low 44, high 50. CHIP low 66, high 75
1970-01-01 00:05:31 driver-btm-soc.c:3219:increase_freq_by_frequency_list_slowly: Increase freq slowly for chain 1 to 670
1970-01-01 00:05:31 temperature.c:1379:get_current_lowest_temperature: current lowest temperature is 44
1970-01-01 00:05:31 driver-btm-soc.c:2890:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 640.000000 to 650.000000 @17.80V.
1970-01-01 00:05:31 driver-btm-soc.c:2891:auto_adaption_high_voltage_increase_frequency: index 1 3
1970-01-01 00:05:31 driver-btm-soc.c:2845:increase_freq_slowly: init_freq = 640.00, final_freq = 650.00, freq_step = 5.00, chain = 1
1970-01-01 00:05:33 temperature.c:1379:get_current_lowest_temperature: current lowest temperature is 44
1970-01-01 00:05:33 driver-btm-soc.c:2890:auto_adaption_high_voltage_increase_frequency: auto adaption increase frequency from 650.000000 to 670.000000 @17.80V.
1970-01-01 00:05:33 driver-btm-soc.c:2891:auto_adaption_high_voltage_increase_frequency: index 2 3
1970-01-01 00:05:33 driver-btm-soc.c:2845:increase_freq_slowly: init_freq = 650.00, final_freq = 670.00, freq_step = 5.00, chain = 1
1970-01-01 00:05:34 temperature.c:1072:read_temp_func: PCB low 44, high 50. CHIP low 67, high 75
1970-01-01 00:05:36 temperature.c:1072:read_temp_func: PCB low 44, high 50. CHIP low 67, high 76
1970-01-01 00:05:37 driver-btm-soc.c:2993:set_timeout: freq 670 final timeout=175
1970-01-01 00:05:37 power.c:808:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.30 ...
1970-01-01 00:05:37 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[130] = 17.732421
1970-01-01 00:05:39 temperature.c:1072:read_temp_func: PCB low 44, high 50. CHIP low 67, high 77
1970-01-01 00:05:40 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[133] = 17.648701
1970-01-01 00:05:42 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 66, high 77
1970-01-01 00:05:42 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[136] = 17.564980
1970-01-01 00:05:44 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 66, high 77
1970-01-01 00:05:45 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[139] = 17.481259
1970-01-01 00:05:47 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 66, high 77
1970-01-01 00:05:48 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[142] = 17.397538
1970-01-01 00:05:50 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 66, high 77
1970-01-01 00:05:50 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[144] = 17.341724
1970-01-01 00:05:52 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 65, high 77
1970-01-01 00:05:53 power.c:570:get_power_voltage_from_iic_value: iic_index for voltage[145] = 17.313817
1970-01-01 00:05:55 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 65, high 77
1970-01-01 00:05:56 power.c:251:check_voltage_multi: retry time: 0
1970-01-01 00:05:56 power.c:213:get_average_voltage: chain[0], voltage is: 17.309853 
1970-01-01 00:05:57 power.c:213:get_average_voltage: chain[1], voltage is: 17.358838 
1970-01-01 00:05:58 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 65, high 77
1970-01-01 00:05:58 power.c:213:get_average_voltage: chain[2], voltage is: 17.260869 
1970-01-01 00:05:58 power.c:224:get_average_voltage: aveage voltage is: 17.309853 
1970-01-01 00:05:58 total rate = 39672
driver-btm-soc.c:2176:check_system_work: ideal hash is 38000
1970-01-01 00:05:58 driver-btm-soc.c:4227:bitmain_soc_init: Init done!
1970-01-01 00:05:58 util.c:2178:process_version_mask: Pool 0 Verion num is 4
1970-01-01 00:05:58 util.c:2178:process_version_mask: Pool 0 Verion num is 4
1970-01-01 00:05:59 driver-btm-soc.c:4416:send_job: Version num 4
1970-01-01 00:06:00 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 64, high 76
1970-01-01 00:06:03 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 75
1970-01-01 00:06:06 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 75
1970-01-01 00:06:08 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 75
1970-01-01 00:06:11 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 75
1970-01-01 00:06:14 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 75
1970-01-01 00:06:16 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 75
1970-01-01 00:06:19 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:06:22 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:06:24 temperature.c:1072:read_temp_func: PCB low 43, high 51. CHIP low 63, high 74
1970-01-01 00:06:27 temperature.c:1072:read_temp_func: PCB low 43, high 51. CHIP low 63, high 74
1970-01-01 00:06:28 pic.c:145:volt_clamp: failed on Chain[0], b[0] = 254, b[2] = 254!
1970-01-01 00:06:30 temperature.c:1072:read_temp_func: PCB low 43, high 51. CHIP low 63, high 74
1970-01-01 00:06:30 pic.c:145:volt_clamp: failed on Chain[0], b[0] = 254, b[2] = 254!
1970-01-01 00:06:31 pic.c:145:volt_clamp: failed on Chain[0], b[0] = 254, b[2] = 254!
1970-01-01 00:06:32 temperature.c:1072:read_temp_func: PCB low 43, high 51. CHIP low 63, high 74
1970-01-01 00:06:33 pic.c:145:volt_clamp: failed on Chain[1], b[0] = 254, b[2] = 254!
1970-01-01 00:06:35 pic.c:145:volt_clamp: failed on Chain[1], b[0] = 254, b[2] = 254!
1970-01-01 00:06:35 temperature.c:1072:read_temp_func: PCB low 43, high 51. CHIP low 63, high 74
1970-01-01 00:06:36 pic.c:145:volt_clamp: failed on Chain[1], b[0] = 254, b[2] = 254!
1970-01-01 00:06:38 temperature.c:1072:read_temp_func: PCB low 43, high 51. CHIP low 63, high 74
1970-01-01 00:06:38 pic.c:145:volt_clamp: failed on Chain[2], b[0] = 254, b[2] = 254!
1970-01-01 00:06:40 pic.c:145:volt_clamp: failed on Chain[2], b[0] = 254, b[2] = 254!
1970-01-01 00:06:40 temperature.c:1072:read_temp_func: PCB low 43, high 51. CHIP low 63, high 74
1970-01-01 00:06:41 pic.c:145:volt_clamp: failed on Chain[2], b[0] = 254, b[2] = 254!
1970-01-01 00:06:43 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:06:46 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:06:48 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:06:51 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:06:54 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:06:56 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:06:59 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:07:02 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:07:04 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 63, high 74
1970-01-01 00:07:07 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 64, high 74
1970-01-01 00:07:10 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 64, high 74
1970-01-01 00:07:12 temperature.c:1072:read_temp_func: PCB low 44, high 51. CHIP low 64, high 74
1970-01-01 00:11:16 driver-btm-soc.c:2101:is_zero_nonce_happened: chain_nonce[0] = 15728
1970-01-01 00:11:16 driver-btm-soc.c:2101:is_zero_nonce_happened: chain_nonce[1] = 15533
1970-01-01 00:11:16 driver-btm-soc.c:2101:is_zero_nonce_happened: chain_nonce[2] = 14765
2020-03-21 15:48:03 temperature.c:1092:update_error_status: Fatal Error: network connection lost!
2020-03-21 15:48:03 temperature.c:1137:check_error_protect: fatal_error_counter increase as: 1, error status: 2
2020-03-21 15:48:05 temperature.c:1092:update_error_status: Fatal Error: network connection lost!
2020-03-21 15:48:05 temperature.c:1137:check_error_protect: fatal_error_counter increase as: 2, error status: 2
2020-03-21 15:48:08 temperature.c:1092:update_error_status: Fatal Error: network connection lost!
2020-03-21 15:48:08 temperature.c:1137:check_error_protect: fatal_error_counter increase as: 3, error status: 2
2020-03-21 15:48:11 temperature.c:1092:update_error_status: Fatal Error: network connection lost!
2020-03-21 15:48:11 temperature.c:1137:check_error_protect: fatal_error_counter increase as: 4, error status: 2
2020-03-21 15:48:13 temperature.c:1092:update_error_status: Fatal Error: network connection lost!
2020-03-21 15:48:13 temperature.c:1137:check_error_protect: fatal_error_counter increase as: 5, error status: 2
2020-03-21 15:48:22 log.c:101:_log_update_name: _log_update_name
2020-03-21 15:48:22 log.c:101:_log_update_name: _log_update_name
2020-03-21 15:48:47 pic.c:145:volt_clamp: failed on Chain[0], b[0] = 254, b[2] = 254!
2020-03-21 15:48:48 pic.c:145:volt_clamp: failed on Chain[0], b[0] = 254, b[2] = 254!
2020-03-21 15:48:50 pic.c:145:volt_clamp: failed on Chain[0], b[0] = 254, b[2] = 254!
2020-03-21 15:48:52 pic.c:145:volt_clamp: failed on Chain[1], b[0] = 254, b[2] = 254!
2020-03-21 15:48:53 pic.c:145:volt_clamp: failed on Chain[1], b[0] = 254, b[2] = 254!
2020-03-21 15:48:55 pic.c:145:volt_clamp: failed on Chain[1], b[0] = 254, b[2] = 254!
2020-03-21 15:48:57 pic.c:145:volt_clamp: failed on Chain[2], b[0] = 254, b[2] = 254!
2020-03-21 15:48:58 pic.c:145:volt_clamp: failed on Chain[2], b[0] = 254, b[2] = 254!
2020-03-21 15:49:01 pic.c:145:volt_clamp: failed on Chain[2], b[0] = 254, b[2] = 254!
2020-03-21 15:53:36 driver-btm-soc.c:2101:is_zero_nonce_happened: chain_nonce[0] = 48288
2020-03-21 15:53:36 driver-btm-soc.c:2101:is_zero_nonce_happened: chain_nonce[1] = 48737
2020-03-21 15:53:36 driver-btm-soc.c:2101:is_zero_nonce_happened: chain_nonce[2] = 45601
2020-03-21 16:18:58 driver-btm-soc.c:2270:check_system_work: The avg rate is 39746.86 in 28 mins, PCB temperature between 49 ~ 57.
2020-03-21 16:49:26 driver-btm-soc.c:2270:check_system_work: The avg rate is 39937.29 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-21 17:19:53 driver-btm-soc.c:2270:check_system_work: The avg rate is 39459.11 in 30 mins, PCB temperature between 48 ~ 56.
2020-03-21 17:50:21 driver-btm-soc.c:2270:check_system_work: The avg rate is 39717.22 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-21 18:20:48 driver-btm-soc.c:2270:check_system_work: The avg rate is 39650.42 in 30 mins, PCB temperature between 48 ~ 56.
2020-03-21 18:51:16 driver-btm-soc.c:2270:check_system_work: The avg rate is 39912.63 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-21 19:21:43 driver-btm-soc.c:2270:check_system_work: The avg rate is 39727.37 in 30 mins, PCB temperature between 48 ~ 56.
2020-03-21 19:52:11 driver-btm-soc.c:2270:check_system_work: The avg rate is 39531.86 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-21 20:22:38 driver-btm-soc.c:2270:check_system_work: The avg rate is 39595.66 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-21 20:53:06 driver-btm-soc.c:2270:check_system_work: The avg rate is 39634.14 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-21 21:23:33 driver-btm-soc.c:2270:check_system_work: The avg rate is 39989.84 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-21 21:54:00 driver-btm-soc.c:2270:check_system_work: The avg rate is 40020.30 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-21 22:24:28 driver-btm-soc.c:2270:check_system_work: The avg rate is 40079.51 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-21 22:54:55 driver-btm-soc.c:2270:check_system_work: The avg rate is 40010.67 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-21 23:25:23 driver-btm-soc.c:2270:check_system_work: The avg rate is 39717.22 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-21 23:55:50 driver-btm-soc.c:2270:check_system_work: The avg rate is 39756.94 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-22 00:26:18 driver-btm-soc.c:2270:check_system_work: The avg rate is 39877.74 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-22 00:56:45 driver-btm-soc.c:2270:check_system_work: The avg rate is 39974.80 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-22 01:27:13 driver-btm-soc.c:2270:check_system_work: The avg rate is 39808.57 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-22 01:57:40 driver-btm-soc.c:2270:check_system_work: The avg rate is 39587.23 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-22 02:28:07 driver-btm-soc.c:2270:check_system_work: The avg rate is 39974.20 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-22 02:58:35 driver-btm-soc.c:2270:check_system_work: The avg rate is 39777.90 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-22 03:29:02 driver-btm-soc.c:2270:check_system_work: The avg rate is 40053.64 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-22 03:59:30 driver-btm-soc.c:2270:check_system_work: The avg rate is 39810.38 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-22 04:29:57 driver-btm-soc.c:2270:check_system_work: The avg rate is 39853.23 in 30 mins, PCB temperature between 45 ~ 57.
2020-03-22 05:00:25 driver-btm-soc.c:2270:check_system_work: The avg rate is 39821.81 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-22 05:30:52 driver-btm-soc.c:2270:check_system_work: The avg rate is 39806.29 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 06:01:20 driver-btm-soc.c:2270:check_system_work: The avg rate is 39927.07 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 06:31:47 driver-btm-soc.c:2270:check_system_work: The avg rate is 39918.83 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 07:02:14 driver-btm-soc.c:2270:check_system_work: The avg rate is 39806.29 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 07:32:42 driver-btm-soc.c:2270:check_system_work: The avg rate is 39928.87 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 08:03:09 driver-btm-soc.c:2270:check_system_work: The avg rate is 39505.99 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 08:33:37 driver-btm-soc.c:2270:check_system_work: The avg rate is 39775.49 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 09:04:04 driver-btm-soc.c:2270:check_system_work: The avg rate is 39754.53 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 09:34:32 driver-btm-soc.c:2270:check_system_work: The avg rate is 39985.41 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 10:04:59 driver-btm-soc.c:2270:check_system_work: The avg rate is 39659.45 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 10:35:26 driver-btm-soc.c:2270:check_system_work: The avg rate is 39740.61 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-22 11:05:54 driver-btm-soc.c:2270:check_system_work: The avg rate is 39737.08 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-22 11:36:22 driver-btm-soc.c:2270:check_system_work: The avg rate is 39913.83 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-22 12:06:49 driver-btm-soc.c:2270:check_system_work: The avg rate is 39828.56 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-22 12:37:16 driver-btm-soc.c:2270:check_system_work: The avg rate is 39916.24 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-22 13:07:44 driver-btm-soc.c:2270:check_system_work: The avg rate is 39632.37 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-22 13:38:12 driver-btm-soc.c:2270:check_system_work: The avg rate is 39870.53 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-22 14:08:39 driver-btm-soc.c:2270:check_system_work: The avg rate is 39773.19 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-22 14:39:07 driver-btm-soc.c:2270:check_system_work: The avg rate is 39682.86 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-22 15:09:34 driver-btm-soc.c:2270:check_system_work: The avg rate is 39939.89 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-22 15:40:01 driver-btm-soc.c:2270:check_system_work: The avg rate is 39791.85 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-22 16:10:29 driver-btm-soc.c:2270:check_system_work: The avg rate is 39726.17 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-22 16:40:57 driver-btm-soc.c:2270:check_system_work: The avg rate is 39797.75 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-22 17:11:24 driver-btm-soc.c:2270:check_system_work: The avg rate is 39880.31 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-22 17:41:51 driver-btm-soc.c:2270:check_system_work: The avg rate is 39813.99 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-22 18:12:19 driver-btm-soc.c:2270:check_system_work: The avg rate is 40015.12 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-22 18:42:47 driver-btm-soc.c:2270:check_system_work: The avg rate is 40008.87 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-22 19:13:14 driver-btm-soc.c:2270:check_system_work: The avg rate is 39752.73 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-22 19:43:42 driver-btm-soc.c:2270:check_system_work: The avg rate is 39684.67 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-22 20:14:09 driver-btm-soc.c:2270:check_system_work: The avg rate is 39631.76 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-22 20:44:36 driver-btm-soc.c:2270:check_system_work: The avg rate is 39767.77 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-22 21:15:04 driver-btm-soc.c:2270:check_system_work: The avg rate is 40011.88 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-22 21:45:31 driver-btm-soc.c:2270:check_system_work: The avg rate is 39807.37 in 30 mins, PCB temperature between 48 ~ 60.
2020-03-22 22:15:59 driver-btm-soc.c:2270:check_system_work: The avg rate is 39864.06 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-22 22:46:26 driver-btm-soc.c:2270:check_system_work: The avg rate is 39778.61 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-22 23:16:54 driver-btm-soc.c:2270:check_system_work: The avg rate is 39820.60 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-22 23:47:21 driver-btm-soc.c:2270:check_system_work: The avg rate is 39873.09 in 30 mins, PCB temperature between 49 ~ 57.

[philipma1957]

section 2

Code:

2020-03-23 00:17:49 driver-btm-soc.c:2270:check_system_work: The avg rate is 40046.76 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-23 00:48:17 driver-btm-soc.c:2270:check_system_work: The avg rate is 39633.54 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-23 01:18:44 driver-btm-soc.c:2270:check_system_work: The avg rate is 40061.46 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-23 01:49:11 driver-btm-soc.c:2270:check_system_work: The avg rate is 39894.76 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-23 02:19:39 driver-btm-soc.c:2270:check_system_work: The avg rate is 39915.64 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-23 02:50:07 driver-btm-soc.c:2270:check_system_work: The avg rate is 40028.72 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-23 03:20:34 driver-btm-soc.c:2270:check_system_work: The avg rate is 40071.09 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 03:51:01 driver-btm-soc.c:2270:check_system_work: The avg rate is 39898.80 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 04:21:29 driver-btm-soc.c:2270:check_system_work: The avg rate is 39674.49 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 04:51:57 driver-btm-soc.c:2270:check_system_work: The avg rate is 39880.15 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 05:22:24 driver-btm-soc.c:2270:check_system_work: The avg rate is 40280.52 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 05:52:52 driver-btm-soc.c:2270:check_system_work: The avg rate is 39647.38 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 06:23:19 driver-btm-soc.c:2270:check_system_work: The avg rate is 40120.44 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-23 06:53:47 driver-btm-soc.c:2270:check_system_work: The avg rate is 40096.08 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 07:24:14 driver-btm-soc.c:2270:check_system_work: The avg rate is 39882.12 in 30 mins, PCB temperature between 45 ~ 57.
2020-03-23 07:54:42 driver-btm-soc.c:2270:check_system_work: The avg rate is 40148.41 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 08:25:10 driver-btm-soc.c:2270:check_system_work: The avg rate is 39741.21 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 08:55:37 driver-btm-soc.c:2270:check_system_work: The avg rate is 39814.11 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-23 09:26:05 driver-btm-soc.c:2270:check_system_work: The avg rate is 39555.35 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-23 09:56:32 driver-btm-soc.c:2270:check_system_work: The avg rate is 39666.07 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-23 10:27:00 driver-btm-soc.c:2270:check_system_work: The avg rate is 40091.27 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-23 10:57:27 driver-btm-soc.c:2270:check_system_work: The avg rate is 39852.63 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-23 11:27:55 driver-btm-soc.c:2270:check_system_work: The avg rate is 39709.93 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-23 11:58:22 driver-btm-soc.c:2270:check_system_work: The avg rate is 39706.39 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-23 12:28:50 driver-btm-soc.c:2270:check_system_work: The avg rate is 39887.37 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-23 12:59:17 driver-btm-soc.c:2270:check_system_work: The avg rate is 39951.93 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-23 13:29:45 driver-btm-soc.c:2270:check_system_work: The avg rate is 39974.58 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-23 14:00:12 driver-btm-soc.c:2270:check_system_work: The avg rate is 39963.36 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-23 14:30:40 driver-btm-soc.c:2270:check_system_work: The avg rate is 40108.11 in 30 mins, PCB temperature between 49 ~ 58.
2020-03-23 15:01:08 driver-btm-soc.c:2270:check_system_work: The avg rate is 39889.17 in 30 mins, PCB temperature between 49 ~ 58.
2020-03-23 15:31:35 driver-btm-soc.c:2270:check_system_work: The avg rate is 39749.12 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-23 16:02:03 driver-btm-soc.c:2270:check_system_work: The avg rate is 39718.95 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-23 16:32:30 driver-btm-soc.c:2270:check_system_work: The avg rate is 39755.14 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-23 17:02:58 driver-btm-soc.c:2270:check_system_work: The avg rate is 39774.29 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-23 17:33:25 driver-btm-soc.c:2270:check_system_work: The avg rate is 39915.22 in 30 mins, PCB temperature between 45 ~ 55.
2020-03-23 18:03:53 driver-btm-soc.c:2270:check_system_work: The avg rate is 39904.81 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-23 18:34:20 driver-btm-soc.c:2270:check_system_work: The avg rate is 39960.75 in 30 mins, PCB temperature between 45 ~ 57.
2020-03-23 19:04:48 driver-btm-soc.c:2270:check_system_work: The avg rate is 39908.60 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-23 19:35:16 driver-btm-soc.c:2270:check_system_work: The avg rate is 39844.06 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-23 20:05:43 driver-btm-soc.c:2270:check_system_work: The avg rate is 39918.23 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-23 20:36:10 driver-btm-soc.c:2270:check_system_work: The avg rate is 39768.88 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-23 21:06:38 driver-btm-soc.c:2270:check_system_work: The avg rate is 39889.94 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-23 21:37:06 driver-btm-soc.c:2270:check_system_work: The avg rate is 39715.95 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-23 22:07:33 driver-btm-soc.c:2270:check_system_work: The avg rate is 39654.63 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-23 22:38:01 driver-btm-soc.c:2270:check_system_work: The avg rate is 39450.69 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-23 23:08:29 driver-btm-soc.c:2270:check_system_work: The avg rate is 39670.23 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-23 23:38:56 driver-btm-soc.c:2270:check_system_work: The avg rate is 40015.12 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-24 00:09:24 driver-btm-soc.c:2270:check_system_work: The avg rate is 40007.06 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 00:39:51 driver-btm-soc.c:2270:check_system_work: The avg rate is 39796.66 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-24 01:10:19 driver-btm-soc.c:2270:check_system_work: The avg rate is 39733.99 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-24 01:40:46 driver-btm-soc.c:2270:check_system_work: The avg rate is 39693.75 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 02:11:14 driver-btm-soc.c:2270:check_system_work: The avg rate is 40085.86 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-24 02:41:41 driver-btm-soc.c:2270:check_system_work: The avg rate is 39888.14 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-24 03:12:09 driver-btm-soc.c:2270:check_system_work: The avg rate is 40038.34 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-24 03:42:36 driver-btm-soc.c:2270:check_system_work: The avg rate is 39919.43 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-24 04:13:04 driver-btm-soc.c:2270:check_system_work: The avg rate is 39537.31 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-24 04:43:31 driver-btm-soc.c:2270:check_system_work: The avg rate is 39695.56 in 30 mins, PCB temperature between 43 ~ 55.
2020-03-24 05:13:59 driver-btm-soc.c:2270:check_system_work: The avg rate is 39952.33 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-24 05:44:26 driver-btm-soc.c:2270:check_system_work: The avg rate is 39776.20 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-24 06:14:54 driver-btm-soc.c:2270:check_system_work: The avg rate is 39724.37 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-24 06:45:21 driver-btm-soc.c:2270:check_system_work: The avg rate is 39707.59 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-24 07:15:49 driver-btm-soc.c:2270:check_system_work: The avg rate is 39459.71 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-24 07:46:17 driver-btm-soc.c:2270:check_system_work: The avg rate is 39707.52 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-24 08:16:44 driver-btm-soc.c:2270:check_system_work: The avg rate is 39894.16 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-24 08:47:11 driver-btm-soc.c:2270:check_system_work: The avg rate is 39595.05 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-24 09:17:39 driver-btm-soc.c:2270:check_system_work: The avg rate is 39954.34 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-24 09:48:07 driver-btm-soc.c:2270:check_system_work: The avg rate is 39920.45 in 30 mins, PCB temperature between 45 ~ 57.
2020-03-24 10:18:34 driver-btm-soc.c:2270:check_system_work: The avg rate is 39971.79 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-24 10:49:02 driver-btm-soc.c:2270:check_system_work: The avg rate is 40081.65 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 11:19:29 driver-btm-soc.c:2270:check_system_work: The avg rate is 39989.84 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 11:49:57 driver-btm-soc.c:2270:check_system_work: The avg rate is 39653.39 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 12:20:24 driver-btm-soc.c:2270:check_system_work: The avg rate is 39536.08 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 12:50:52 driver-btm-soc.c:2270:check_system_work: The avg rate is 40069.62 in 30 mins, PCB temperature between 48 ~ 58.
2020-03-24 13:21:19 driver-btm-soc.c:2270:check_system_work: The avg rate is 39832.77 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 13:51:47 driver-btm-soc.c:2270:check_system_work: The avg rate is 40010.07 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 14:22:14 driver-btm-soc.c:2270:check_system_work: The avg rate is 39908.60 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 14:52:42 driver-btm-soc.c:2270:check_system_work: The avg rate is 40160.44 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-24 15:23:09 driver-btm-soc.c:2270:check_system_work: The avg rate is 39953.13 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-24 15:53:37 driver-btm-soc.c:2270:check_system_work: The avg rate is 39551.74 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-24 16:24:05 driver-btm-soc.c:2270:check_system_work: The avg rate is 39736.40 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 16:54:32 driver-btm-soc.c:2270:check_system_work: The avg rate is 39821.34 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-24 17:25:00 driver-btm-soc.c:2270:check_system_work: The avg rate is 39978.79 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 17:55:27 driver-btm-soc.c:2270:check_system_work: The avg rate is 39930.87 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 18:25:55 driver-btm-soc.c:2270:check_system_work: The avg rate is 39990.22 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 18:56:22 driver-btm-soc.c:2270:check_system_work: The avg rate is 39730.46 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 19:26:50 driver-btm-soc.c:2270:check_system_work: The avg rate is 39993.23 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 19:57:17 driver-btm-soc.c:2270:check_system_work: The avg rate is 39845.41 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 20:27:45 driver-btm-soc.c:2270:check_system_work: The avg rate is 39648.58 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 20:58:13 driver-btm-soc.c:2270:check_system_work: The avg rate is 39936.09 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 21:28:40 driver-btm-soc.c:2270:check_system_work: The avg rate is 39566.77 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-24 21:59:08 driver-btm-soc.c:2270:check_system_work: The avg rate is 39823.61 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-24 22:29:35 driver-btm-soc.c:2270:check_system_work: The avg rate is 39638.38 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-24 23:00:03 driver-btm-soc.c:2270:check_system_work: The avg rate is 39592.64 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-24 23:30:30 driver-btm-soc.c:2270:check_system_work: The avg rate is 39927.25 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 00:00:58 driver-btm-soc.c:2270:check_system_work: The avg rate is 39940.90 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-25 00:31:26 driver-btm-soc.c:2270:check_system_work: The avg rate is 39922.25 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 01:01:53 driver-btm-soc.c:2270:check_system_work: The avg rate is 39601.07 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-25 01:32:21 driver-btm-soc.c:2270:check_system_work: The avg rate is 39620.31 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 02:02:48 driver-btm-soc.c:2270:check_system_work: The avg rate is 39945.31 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 02:33:16 driver-btm-soc.c:2270:check_system_work: The avg rate is 39880.15 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-25 03:03:43 driver-btm-soc.c:2270:check_system_work: The avg rate is 40058.79 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 03:34:11 driver-btm-soc.c:2270:check_system_work: The avg rate is 40067.48 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 04:04:39 driver-btm-soc.c:2270:check_system_work: The avg rate is 39866.92 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 04:35:06 driver-btm-soc.c:2270:check_system_work: The avg rate is 39569.78 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-25 05:05:34 driver-btm-soc.c:2270:check_system_work: The avg rate is 39725.57 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 05:36:01 driver-btm-soc.c:2270:check_system_work: The avg rate is 39576.40 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 06:06:29 driver-btm-soc.c:2270:check_system_work: The avg rate is 40073.23 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 06:36:57 driver-btm-soc.c:2270:check_system_work: The avg rate is 40061.80 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-25 07:07:24 driver-btm-soc.c:2270:check_system_work: The avg rate is 39870.08 in 30 mins, PCB temperature between 44 ~ 55.
2020-03-25 07:37:51 driver-btm-soc.c:2270:check_system_work: The avg rate is 40168.86 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 08:08:19 driver-btm-soc.c:2270:check_system_work: The avg rate is 39871.29 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-25 08:38:47 driver-btm-soc.c:2270:check_system_work: The avg rate is 39801.96 in 30 mins, PCB temperature between 45 ~ 57.
2020-03-25 09:09:14 driver-btm-soc.c:2270:check_system_work: The avg rate is 39983.83 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-25 09:39:42 driver-btm-soc.c:2270:check_system_work: The avg rate is 39785.12 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-25 10:10:09 driver-btm-soc.c:2270:check_system_work: The avg rate is 39635.38 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-25 10:40:37 driver-btm-soc.c:2270:check_system_work: The avg rate is 40029.32 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-25 11:11:05 driver-btm-soc.c:2270:check_system_work: The avg rate is 39919.25 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-25 11:41:32 driver-btm-soc.c:2270:check_system_work: The avg rate is 39893.55 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-25 12:12:00 driver-btm-soc.c:2270:check_system_work: The avg rate is 39663.02 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-25 12:42:27 driver-btm-soc.c:2270:check_system_work: The avg rate is 39922.25 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 13:12:55 driver-btm-soc.c:2270:check_system_work: The avg rate is 39869.48 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-25 13:43:23 driver-btm-soc.c:2270:check_system_work: The avg rate is 39971.58 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-25 14:13:50 driver-btm-soc.c:2270:check_system_work: The avg rate is 39851.43 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-25 14:44:18 driver-btm-soc.c:2270:check_system_work: The avg rate is 39788.73 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-25 15:14:45 driver-btm-soc.c:2270:check_system_work: The avg rate is 39939.29 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-25 15:45:13 driver-btm-soc.c:2270:check_system_work: The avg rate is 39663.02 in 30 mins, PCB temperature between 49 ~ 58.
2020-03-25 16:15:41 driver-btm-soc.c:2270:check_system_work: The avg rate is 39948.72 in 30 mins, PCB temperature between 49 ~ 58.
2020-03-25 16:46:08 driver-btm-soc.c:2270:check_system_work: The avg rate is 39529.46 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-25 17:16:36 driver-btm-soc.c:2270:check_system_work: The avg rate is 39697.90 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-25 17:47:03 driver-btm-soc.c:2270:check_system_work: The avg rate is 39732.79 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-25 18:17:31 driver-btm-soc.c:2270:check_system_work: The avg rate is 39930.26 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-25 18:47:59 driver-btm-soc.c:2270:check_system_work: The avg rate is 40182.10 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 19:18:26 driver-btm-soc.c:2270:check_system_work: The avg rate is 39684.12 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 19:48:54 driver-btm-soc.c:2270:check_system_work: The avg rate is 40059.39 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-25 20:19:21 driver-btm-soc.c:2270:check_system_work: The avg rate is 39982.02 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-25 20:49:49 driver-btm-soc.c:2270:check_system_work: The avg rate is 39736.40 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-25 21:20:16 driver-btm-soc.c:2270:check_system_work: The avg rate is 39435.65 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-25 21:50:44 driver-btm-soc.c:2270:check_system_work: The avg rate is 39872.49 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-25 22:21:12 driver-btm-soc.c:2270:check_system_work: The avg rate is 39765.27 in 30 mins, PCB temperature between 50 ~ 58.
2020-03-25 22:51:39 driver-btm-soc.c:2270:check_system_work: The avg rate is 39897.16 in 30 mins, PCB temperature between 50 ~ 58.
2020-03-25 23:22:07 driver-btm-soc.c:2270:check_system_work: The avg rate is 39877.14 in 30 mins, PCB temperature between 51 ~ 59.
2020-03-25 23:52:34 driver-btm-soc.c:2270:check_system_work: The avg rate is 39779.81 in 30 mins, PCB temperature between 51 ~ 59.
2020-03-26 00:23:02 driver-btm-soc.c:2270:check_system_work: The avg rate is 40073.23 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 00:53:29 driver-btm-soc.c:2270:check_system_work: The avg rate is 39918.83 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 01:23:57 driver-btm-soc.c:2270:check_system_work: The avg rate is 39900.60 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 01:54:25 driver-btm-soc.c:2270:check_system_work: The avg rate is 39825.42 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-26 02:24:52 driver-btm-soc.c:2270:check_system_work: The avg rate is 39659.45 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-26 02:55:20 driver-btm-soc.c:2270:check_system_work: The avg rate is 39960.15 in 30 mins, PCB temperature between 47 ~ 56.
2020-03-26 03:25:48 driver-btm-soc.c:2270:check_system_work: The avg rate is 39813.99 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-26 03:56:15 driver-btm-soc.c:2270:check_system_work: The avg rate is 39831.57 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-26 04:26:42 driver-btm-soc.c:2270:check_system_work: The avg rate is 40291.95 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-26 04:57:10 driver-btm-soc.c:2270:check_system_work: The avg rate is 40099.09 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-26 05:27:38 driver-btm-soc.c:2270:check_system_work: The avg rate is 39836.24 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-26 05:58:05 driver-btm-soc.c:2270:check_system_work: The avg rate is 39687.13 in 30 mins, PCB temperature between 46 ~ 57.
2020-03-26 06:28:32 driver-btm-soc.c:2270:check_system_work: The avg rate is 39922.86 in 30 mins, PCB temperature between 45 ~ 57.
2020-03-26 06:59:00 driver-btm-soc.c:2270:check_system_work: The avg rate is 39898.37 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-26 07:29:27 driver-btm-soc.c:2270:check_system_work: The avg rate is 39521.03 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-26 07:59:55 driver-btm-soc.c:2270:check_system_work: The avg rate is 39913.23 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-26 08:30:23 driver-btm-soc.c:2270:check_system_work: The avg rate is 39685.27 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-26 09:00:50 driver-btm-soc.c:2270:check_system_work: The avg rate is 39720.83 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-26 09:31:18 driver-btm-soc.c:2270:check_system_work: The avg rate is 39659.41 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-26 10:01:45 driver-btm-soc.c:2270:check_system_work: The avg rate is 39731.67 in 30 mins, PCB temperature between 44 ~ 56.
2020-03-26 10:32:13 driver-btm-soc.c:2270:check_system_work: The avg rate is 39431.44 in 30 mins, PCB temperature between 45 ~ 56.
2020-03-26 11:02:40 driver-btm-soc.c:2270:check_system_work: The avg rate is 40021.14 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-26 11:33:08 driver-btm-soc.c:2270:check_system_work: The avg rate is 39939.70 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-26 12:03:35 driver-btm-soc.c:2270:check_system_work: The avg rate is 39648.01 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 12:34:03 driver-btm-soc.c:2270:check_system_work: The avg rate is 39887.97 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-26 13:04:30 driver-btm-soc.c:2270:check_system_work: The avg rate is 39974.80 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 13:34:58 driver-btm-soc.c:2270:check_system_work: The avg rate is 39722.56 in 30 mins, PCB temperature between 48 ~ 58.
2020-03-26 14:05:25 driver-btm-soc.c:2270:check_system_work: The avg rate is 39759.85 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 14:35:53 driver-btm-soc.c:2270:check_system_work: The avg rate is 39734.67 in 30 mins, PCB temperature between 46 ~ 56.
2020-03-26 15:06:21 driver-btm-soc.c:2270:check_system_work: The avg rate is 39650.38 in 30 mins, PCB temperature between 47 ~ 57.
2020-03-26 15:36:48 driver-btm-soc.c:2270:check_system_work: The avg rate is 40012.71 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 16:07:16 driver-btm-soc.c:2270:check_system_work: The avg rate is 39740.61 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 16:37:44 driver-btm-soc.c:2270:check_system_work: The avg rate is 39878.95 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 17:08:11 driver-btm-soc.c:2270:check_system_work: The avg rate is 39797.87 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 17:38:39 driver-btm-soc.c:2270:check_system_work: The avg rate is 39783.31 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-26 18:09:06 driver-btm-soc.c:2270:check_system_work: The avg rate is 39730.46 in 30 mins, PCB temperature between 49 ~ 58.
2020-03-26 18:39:34 driver-btm-soc.c:2270:check_system_work: The avg rate is 39801.96 in 30 mins, PCB temperature between 49 ~ 58.
2020-03-26 19:10:01 driver-btm-soc.c:2270:check_system_work: The avg rate is 39738.29 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-26 19:40:29 driver-btm-soc.c:2270:check_system_work: The avg rate is 39699.10 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-26 20:10:56 driver-btm-soc.c:2270:check_system_work: The avg rate is 39596.25 in 30 mins, PCB temperature between 48 ~ 56.
2020-03-26 20:41:24 driver-btm-soc.c:2270:check_system_work: The avg rate is 40016.93 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-26 21:11:51 driver-btm-soc.c:2270:check_system_work: The avg rate is 39708.20 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-26 21:42:19 driver-btm-soc.c:2270:check_system_work: The avg rate is 39497.61 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-26 22:12:46 driver-btm-soc.c:2270:check_system_work: The avg rate is 39891.15 in 30 mins, PCB temperature between 49 ~ 57.
2020-03-26 22:43:14 driver-btm-soc.c:2270:check_system_work: The avg rate is 39837.45 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 23:13:41 driver-btm-soc.c:2270:check_system_work: The avg rate is 39776.80 in 30 mins, PCB temperature between 48 ~ 57.
2020-03-26 23:44:09 driver-btm-soc.c:2270:check_system_work: The avg rate is 39773.69 in 30 mins, PCB temperature between 48 ~ 57.

I have   more but this is what you need to do

[TonyGotaTruck]

Im sorry but, I don't know what a GUI is nor how to locate it... Ive tried searching through everything and have not found it.

   I think I have heat issues. I can run at night but about 10AM they (2 miners) go down.

[philipma1957]

Im sorry but, I don't know what a GUI is nor how to locate it... Ive tried searching through everything and have not found it.

   I think I have heat issues. I can run at night but about 10AM they (2 miners) go down.

I can't help you if you can not find your miner on the browser.

I can't help you if you do not understand the screen shots. Of the gui that I posted.

Sorry about that.

My advice to you is sell the gear and don't mine.

As without the knowledge to access to the miners gui  you can not mine properly.

I will try this 1 more time.   The gui is the browser page that you add the pools you mine to.

The pools are filled out according to you.

Which means  you went to the gui and then went to the pools page.

[mikeywith]

Im sorry but, I don't know what a GUI is nor how to locate it... Ive tried searching through everything and have not found it.

GUI = graphical user interface

In other words, you open your browser (Google Chrome for an example), and then you type the IP address of the miner (For an example 192.168.1.10, that opens the GUI of your miner.

from there you can see Miner status, Kernel logs and all the other information we need to see, the kernel log is a text which you copy and paste here, the status page and setting page you should take a screenshot, upload it to imgur.com and post the image URL here.

And honestly, if you can't do the above you shouldn't be mining.

[BitMaxz]

Im sorry but, I don't know what a GUI is nor how to locate it... Ive tried searching through everything and have not found it.

   I think I have heat issues. I can run at night but about 10AM they (2 miners) go down.

That's the weird thing if you don't know how to access the WebGUI like the above said you can access it through the browser.

How did you setup the miner(adding Pool server)? you can find the kernel logs under that page on different tabs.

Here's the sample Web GUI below



I'll make it big for you. As you can see in the image the whole thing is a Web GUI. You can find the kernel logs on the other tab between the upgrade and monitor tab.

If you are in kernel logs you can see what philipma1957 posted above copy them and post it here with "insert code" or paste it to pastebin.com and post the URL here.

And some images or screenshot of your Web Gui from the miner status tab and post it here. So that we can troubleshoot what exactly the issue of your miner.